IMP 036-MARZO 2015
I.MANUAL
MBP, S.L.
Plgno. Ansoleta,
C. Anboto, 17
01006 VITORIA
Tfno. 34 945 132744
Fax.
34 945134756
e-mail: info@mbpspray.com
www.mbpspray.com
WARRANTY
1.-
2.-
3.-
M.B.P., will any repairs necessary during the first 12 months after purchase of a
new unit, with the exceptions shown under 1 and 2 below, and under the conditions
shown in item 3.
Damage caused by external abuse, customer negligence, or failure to operate
the unit in accordance with the instructions supplied with the unit.
Normal maintenance items.
Within the first 12 months after purchase, M.B.P. will pay 100% of the
cost of covered repairs.
In no case will M.B.P.liability extend beyond repair or repalacement of the equipment.
Such liability is limited to the amount of the original purchase price paid for the unit,
minus a reasonable deduction for the time the unit has been in service. It is the
responsibility of the purchaser under this warranty to ship or deliver the failed paint
sprayer to the authorized service center at the purchaser’s expence. Parts or
components covered under this warranty may either be repaired or replaced at
M.B.P. option.
Equipent not covered by M.B.P. warranty. Accessories or components of equipment
sold by M.B.P. that are nort manufactured by M.B.P. are subject to the warranty,
if any, of their manufacturer. M.B.P. will provide purchaser with reasonable
assistance in making such claims.
The Industry Department of The Basque Goverment, states that all electric and
pneumatic airless equipment manufacture by M.B.P. S.L., follows the ’’CE’’
standards under the number 83/392/CEE.
EC//
4 99 ATEX
ELECTRIC
PAINTING PUMP
KS 2300
SPRAY EQUIPMENT
MODELO / MODEL KS 2300
Este producto cumple con la siguiente directiva de la Comunidad
Europea.
This Product complies with the following European Comunity
Directive.
Directiva 2006/42/CEE y 94/9/CEE Atex sobre máquinas.
Machinery Directive 2006/42/EC and 94/9/EC Atex Directive.
APROBADO POR /
APPROVED BY AITOR ORTIZ
FECHA / DATE
MBP, S.L. figura inscrita en el Registro Industrial del País Vasco con
el Nº 01/8030 y cumple los requisitos para el desarrollo de su
actividad comercial.
MBP, S.L. is registered in the Industrial Register of the Basque
Country with the Nº 01/8030.
DECLARACION DE CONFORMIDAD ‘’CE’’
‘’EC’’ DECLARATION OF CONFORMITY
INDEX
Pump components ...............................
Safety warnings ..................................
Operating instructions ..........................
Cleaning ...........................................
Troubleshooting chart ..........................
Parts drawing & list ............................
Wiring diagram ..................................
Pressure control assy .........................
Shutdown and care ............................
Standard spray tips .............................
Accesories ........................................
1
3
5
6
7
9
11
12
13
13
14
15
14
PUMP COMPONENTS
1
5
4
12
10
3
9
13
1
2
8
7
6
11
7
1
10
PACKOIL
REF: B.100.20
HP FILTER
SCREEN
G.100.20-60 MESH
G.100.05-100 MESH
G.100.21-200 MESH
REF. GR.70.70-70 MESH
REF. GR.71.20-120 MESH
SIEVE
REF:
REF:
REF:
ACCESORIES
TIP EXTENSIONS 90cms. 30cms.
J.275
J.272
J.271
AIRLESS GUN FILTER
MESH
50
100
200
COLOUR
WHITE
YELLOU
RED
REF.
J.260.01
J.260.02
J.260.03
2
PUMP COMPONENTS
13
SHUTDOWN AND CARE
1.-
2.-
3.-
4.-
5.-
6.-
7.-
8.-
9.-
10.-
11.-
12.-
13.-
Pressure regulator.
Ref: 100.610.00
On / Off switch.
Ref: CEA.026
Pressure drain valve.
Ref: 100.420.00
Suction pipe.
Ref: 102.300.00
Displacement pump.
Ref: 102.200.00
Check that the product doesn’t leak.
Put a drop of oil.
Trasmitting pressure.
Ref: 100.410.00
Pressure control assy.
Ref: 102.600.00
Strainer.
Ref: D.910.00
Paint outlet.
Ref: G.100.06
Wire.
Ref: 102.630.00
Troley.
Ref: 102.500.00
Gun.
Ref: J.600.00
*
*
*
Check the packing nut daily. First follow the Pressure Relief Procedure. Be
sure the packing nut is 1/3 full of Oilpack at all times to help prevent fluid
buildup on the piston rod and premature wear of packings.
Clean the fluid filter often and wherenever the sprayer is stored. First follow the
Pressure relief procedure.
Flush the sprayer at the end of each work day and fill it with mineral spirits to
help prevent pump corrosion and freezing.
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
.021’’
21.20
21.40
21.60
.023’’
23.20
23.40
23.60
.025’’
25.20
25.40
25.60
.027’’
27.20
27.40
27.60
.029’’
29.20
29.40
29.60
.031’’
31.20
31.40
31.60
0.30
0.45
0.64
0.87
1.13
1.36
1.74
2.08
2.49
2.91
3.33
3.86
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
100-150
200-250
300-350
.009’’
9.20
9.40
9.60
.011’’
11.20
11.40
11.60
.013’’
13.20
13.40
13.60
.015’’
15.20
15.40
15.60
.017’’
17.20
17.40
17.60
.019’’
19.20
19.40
19.60
0.48 MM. 0.43 MM. 0.38 MM. 0.33 MM. 0.28 MM. 0.23 MM.
0.79 MM. 0.74 MM. 0.68MM. 0.63 MM. 0.58 MM. 0.53 MM.
ORIFICE SIZE
MM/INCHES
FLOW IN
LITRES/MIN
FAN WIDTH AT
300 MM.
ORIFICE SIZE
MM/INCHES
FLOW IN
LITRES/MIN
FAN WIDTH AT
300 MM.
STANDARD SPRAY TIPS
8
19
18
21
1
5
15
17
4
25
27
28
28
20
7
15
12
2
11
9
6
23
24
22
3
26
ATTENTION
This equipment generates very high fluid pressure. High pressure spray can cause
serious injury. Read and understand all instructions before operating.
Never point the spray gun at anyone or at any part of the body.
Never put hand, fingers over the spray tip.
Always have the tip guard in place on the spray gun while spraying.
High pressure fluid in the hoses can be very dangerous. If the hose develops a
leak, split or rupture due to any kind of wear, damage or misuse, the high pressure
spray emitted from it can cause a fluid injection injury or other serious bodily injury
or properly damage.
Never use a damaged hose
Tighten all fluid connections securely before each use. High pressure fluid can
dislodge a loose coupling or allow high pressure spray to be emitted from the
coupling.
Proper hose grounding continuity is essential to maintaining a grounded spray
system.
If any fluid appears to penetrate your skin, get emergency medical care at once.
Do not treat as a simple cut. Tell the doctor exactly what fluid was injected.
All chemicals used in the pump must be compatible with the wetted parts of the
pump.
PRESSURE HAZARD
This pump can develope 240 bar working pressure. Be sure that all spray
equipment and accesories used are rated to withstand this pressure. Do not
exceed the maximum working pressure of any component or accessory used in
the system.
SAFETY WARNINGS
3 12
PRESSURE CONTROL ASSY
Nº REF. DESCRIPTION Q Nº REF. DESCRIPTION Q
CEA.026
CEA.027
CEA.030
100.660.00
100.411.00
CEA.037
F.900.20
100.600.03
CAR.022
100.650.00
CTU.105
CTB.013
ON/OFF SWITCH
CONNECTOR
NUT
MOTOR CABLE
PRESSURE TRANSMITTER C.
CONTROL CAR
CONNECTOR
BOX
WASHER
CONTROL CAR INVERTER C.
NUT
SCREW
102.600.01
102.600.02
CEA.041
100.610.00
100.640.00
100.620.00
100.630.00
CTB.005
CAR.254
CTJ.005
CTU.015
CEA.034
BOX
COVER
FRECUENCY INVERTER
PRESSURE REGULATOR
INVERTER OUTLET CABLE
INVERTER ON/OFF SWITCH CABLE
WIRE
SCREW
WASHER
SCREW
NUT
CONNECTOR
1
1
1
1
1
1
3
1
4
1
5
4
1
1
1
1
1
1
1
1
2
2
2
2
1
2
3
4
5
6
7
8
9
11
12
15
17
18
19
20
21
22
23
24
25
26
27
28
COM
LI 1
0
1
L3
MOTOR
PEW UV
PE
220 V 50 Hz.
BROWN
BLUE
BROWN
BLUE
FREQUENCY
INVERTER
GREY
GREEN
WHITE
BROWN
PRESSURE
REGULATOR
GREY
BROWN
YELLOW
GREEN
WHITE
PRESSURE
TRANSMITTER
L1
COM
1
2
+244+24
3
COM
5
6 7
COM
8
LI 1
10
9
1
2
3
4
4
3
2
COM
1
2
+244+243COM
5
6 7
COM
8
LI 1
10
9
1
1
2
3
3 2 1
+24
4
SAFETY WARNINGS
11
PRESSURE RELIEF PROCEDURE
To reduce the risk of serious bodily injury, including fluid injection, splashing fluid
or solvent in the eyes or on the skin, or injury from moving parts or electric shock,
allways follow this procedure whenever you shut off the sprayer, when checking
or servicing any part of the spray system, when installing, cleaning or changing
spray tips, and whenever you stop spraying:
· Engage the gun safety latch
· Turn the ON/OFF switch to OFF (red)
· Unplug the power supply cord (No. 14)
· Disengage the gun safety latch. Hold a metal part of the gun to the side of a
grounded metal pail, and trigger the gun to relieve pressure.
· Engage the gun safety latch
· Open the pressure drain valve (No. 3), having a container ready to catch the
drainage
FIRE OR EXPLOSION HAZARD
Static electricity is created by the flow of fluid through the pump and hose. If every
part of the spray equipment is not properly grounded, sparking may occur and the
system may become hazardous. Sparking may also occur when plugging in or
unplugging a power supply cord. Sparks can ignite fumes from solvents and the
fluid being sprayed, dust particles, whether you are spraying indoors or outdoors,
and can cause a fire or explosion.
If you experience any static sparking or even a slight shock while using the
equipment, stop spraying immediately. Check the system for proper grounding.
Do not use the system again until the problem has been identified and corrected.
WIRING DIAGRAM
1
3
5
7
4
6
8
20
24
9
21
22
10
10
11
11
12
13
14
15
16
17
18
19
32
34
33
35
36
31
30
29
23
25
28
26
27
37
38
OPERATION
5 10
1.-
2.-
3.-
4.-
5.-
6.-
7.-
8.-
9.-
10.-
Connect hose and gun (use two wrenches to tighten the fittings). Don´t install the
spray tip yet.
Check the electrical service. Be sure the electrical installation is properly rated for
the sprayer and that the outlet you use is properly grounded. Use an extension cord
which has 3 wires of a minimum 4 mm size, and a maximum of 45 m long. Longer
lengths may affect sprayer performance.
Prepare the paint. Stir the paint to mix pigments. Strain the paint to remove particles
that could clog the filters or spray tip.
Put the suction tube into the pail container.
Lower the pressure setting by turning the pressure adjusting knob all the way
counterclockwise
Disengage the gun safety latch.
To prime the pump, hold a metal part of the gun firmly into a metal waste container.
Squeeze the trigger and hold it open, turn the ON/OFF switch to ON, and slowly
increase the pressure setting until the sprayer starts. Keep the gun triggered until all
air is forced out of the system and the paint flows freely from the gun. Release the
trigger and engage the gun safety latch.
Note: If the pump is hard to prime, place a container under the pressure drain
valve and open it. When fluid comes from the valve, close it. Then disengage the
gun safety latch and proceed as in point 7.
Check all fluid connections for leaks. If any are found, follow the pressure relief,
before tightening connections.
Install the spray tip and tip guard. Be sure the gun safety latch is engaged.
Note: your new sprayer was factory tested in lightweight oil which was left in to
protect pump parts. before using water-base paint, flush with mineral spirits followed
by clean water. Before using oil-case paint, flush with mineral spirits only.
Fill the packing nut with MBP - Packoil
PART LIST DISPLACEMENT PUMP
REF.
102.210.00
CB0.110
080.230.00
102.200.03
102.200.04
CJT.044
102.200.05
102.200.01
102.200.06
CJT.045
102.200.07
102.200.08
080.200.10
080.200.11
CB0.111
102.220.00
102.200.09
102.200.02
CPA.218
CTB.036
CAR053
100.420.00
G.100.06
CJT.164
100.410.01
CEA.027
100.411.00
CNA.057
G.920.03
MAPM.203
102.310.00
CJT.175
102.300.01
CC0001
MAPM.202
102.320.00
D.910.00
DESCRIPTION
Rod
Ball
Seat ball
Tapón
Sleeve
O-ring
Packings
Body
Packings
O-ring
Sleeve
Joint
Sleeve-guide
Pin
Ball
Seat
Joint
Valve housing
Pin
Screw
Washer
Valve
Nipple
Joint
Body
Packing nut
Sensor
Nipple
Spring
Tube
Suction
Joint
Nipple
Clamp
Hose
Tube
Strainer
Nº
1
*3
4
5
6
*7
*8
9
*10
*11
12
13
14
15
*16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
*KIT 043: Includes packings (up &
down) packing glands and balls.
Q
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
69
1.-
2.-
3.-
4.-
5.-
6.-
7.-
8.-
9.-
10.-
Follow the Pressure Relief Procedure.
If the sprayer has been used before, remove the filter bowl and screen.
Clean the screen separately and install the bowl without the screen to
flush it.
Close the pressure drain valve
For 2 liters of compatible solvent into a grounded metal pail. Put the
suction tube in the pail.
Remove the spray tip from the gun
Lower the pressure setting by turning the pressure adjusting knob all the
way counterclockwise.
Hold a metal part of the gun against a metal container. Squeeze the trigger
and hold it open, turn the ON/OFF switch to ON, and slowly increase
the pressure setting until the sprayer starts. Keep the gun triggered until
all air is forced out of the system and the solvent flows freely from the
gun. Release the trigger and engage the gun safety latch.
Remove the suction tube from the pail. Disengage the gun safety latch
and trigger the gun to force solvent from the hose. Do not let the pump
run dry for more than 15 seconds to avoid damaging the pump packings.
Then follow the Pressure Relief Procedure.
Leave the pressure drain valve open until you are ready to use the sprayer
again. If the screen was removed, unscrew the filter bowl and reinstal the
clean screen. Reinstall the bowl, hand tight.
If you flushed with mineral spirits and are going to use water-base paint,
flush with clean water.
CLEANINGPARTS LIST
REF.
102.110.00
CTB.003
102.111.01
CTB.014
CPA.204
CB1010
A1.920.02
CB1012
CB2007
A1.920.03
CB2008
A1.910.02
CPA.501
102.111.02
CB1009
102.121.00
CB2002
102.120.02
A1.930.03
102.100.01
CTB.204
DESCRIPTION
Motor
Screw
Housing
Screw
Pin
Sleeve
Gear
Bearing
Washer
Gear
Washer
Rod
Cotter pin
Body
Bearing
Rod
Sleeve
Rod
Pin
Cover
Screw
Nº
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Q
1
4
1
4
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
2
3
5
4
8
5
6
10
13
11
12
14
15
16
17
6
7
9
19
18
20
21
7
SOLUTION
Remove siphon tube and feel lower ball check
to be sure it is free to move off it is seat. Place
full cup of paint thinner over end of fluid
section and turn on pump.
Remove and clean.
Hold gun trigger in open position and run unit
about 10 seconds until air is purged. Check
for siphon tube leak.
Replace.
Prime pump with compatible solvent. Bring up
to pressure, carefully remove pump from
solvent container and immerse inlet tube into
heavy material to be sprayed. With nozzle tip
removed trigger gun until heavy material
appears at gun.
Replace nozzle tip and you are ready to spray.
Remove and clean.
Check connection and seal.
Relieve pressure, remove tip and clean.
Adjust to increase pressure.
Clean or temporaly remove.
Replace or clean.
Hold gun trigger in open position and run
about 10 seconds until airs is purged.
Replace.
Replace.
With gun trigger closed, allow unit to pump
up to pressure and shut off if pump
momentarily starts, internal leak is indicated
and fluid section rebuild is necesary.
CAUSE
Dried out piston packings.
Stuck valve balls.
Pump inlet screen plugged.
Air in pump or hose
Packings worn.
Fluid too viscous.
Siphon tube clogged.
Siphon tube air leak.
Clogged tip.
Pressure adjusting knob not
properly set.
Pump inlet strainer dirty.
Valve balls or seats worn or
dirty.
Air in pump or hose.
Packings worn.
Worn spray tip.
Internal leakage.
TROUBLE
Unit will not
prime
Unit will not
build or
maintain
pressure.
TROUBLESHOOTING CHART
8
CAUSE
Fuid leak.
Fluid too viscous.
Too large a spray tip.
Worn packing.
Upper packings worn.
Piston rod worn.
Too large a tip size.
Pressure adjustment wrong.
Insufficient fluid delivery.
Fuid too viscous.
Pressure adjustment low.
Improper voltage supply.
Excessive pressure.
Excesive extention cord length
or improper wire gauge.
TROUBLE
Unit will not
build or
maintain
pressure.
Fuid leakage
out relief hole
at pressure
control.
Fluid leakage
at upper end
of fluid
section.
Bad spray
pattern.
Unit lacks
power.
Blown fuses
at pump.
SOLUTION
Check for external leaks including hydraulic
fittings attached to pressure control
housing.
Consult manufacturers recommendations on
paint container label.
Change tip.
Repack or replace transducer.
Relieve pressure and tighten packing take
up nut or replace packings.
Replace.
Change to a smaller tip size.
Adjust pressure control knob.
Clean all straines and filters in system.
Add solvent to fluid according to
manufacturer’s recommendations.
Increase.
Reconnect input voltage accordingly.
Have Service Center recalibrate the pressure
control.
Use 3x1,5 mm. section wire or larger up to
maximum of 50 meters. For additional lenght,
more airless hose may be used.
Loading...