Mazda KF69 79 EZX, KD37 79 EZX Instructions Manual

1

GENUINE CAR-NAVIGATION UNIT

INSTALLATION INSTRUCTIONS

Thank you for purchasing a genuine Mazda accessory.
Before removal and installation, be sure to thoroughly read these instructions.
Please read the contents of this booklet in order to properly install and use the
car-navigation unit. Your safety depends on it.
Keep these instructions with your vehicle records for future reference.

• There are several WARNING and CAUTION sections in this booklet concerning

safety when installing or removing the car-navigation unit. Always read and follow them
in order to prevent injuries, accidents, and possible damage to the vehicle.

WARNING: Indicates a situation in which serious injury or death could result if

the warning is ignored.

CAUTION: Indicates a situation in which bodily injury or damage to the vehicle

could result if the caution is ignored.

• For areas indicating the tightening torque in this instruction manual, tighten to the
specified torque using a torque wrench. For areas in which the tightening torque is
indicated inside parentheses ( ), the tightening torque is indicated as a reference value,
however tightening using a torque wrench is not necessary.

• Do not modify the car-navigation unit.

• Do not install the car-navigation unit in any way other than described in the following

instructions.

• If in any doubt, please ask your Mazda dealer to install the accessory in order to
prevent errors in installation.

• If you have any questions about the use of the accessory, ask your Mazda dealer for
proper advice before using it.

• Mazda and its suppliers are not responsible for injuries, accidents, and damage to
persons and property that arise from the failure of the dealer or installer to follow these
instructions.

• To ensure safety and reliability of the work, installation, removal and disposal work

must be carried out by an Authorized Mazda Dealership.

•

Be careful not to lose removed parts, and be sure that they are kept free from
scratches, grease or other dirt.

PART NAME: CAR-NAVIGATION UNIT

PART NUMBER: KF69 79 EZX (MEXICO)

KD37 79 EZX (US/CANADA)

VEHICLE: MAZDA CX-5

To the dealer

• Please turn over these instructions to the customer after installation.

To the customer

• Keep these instructions after installation. The instructions may be necessary
for installing other optional parts or removal of this accessory.

• Should the vehicle or this accessory be resold, always leave these instructions
with it for the next owner.

WARNING

NOTE

00

ＧＢ

00

E

00

F

2

▼ PARTS LIST

• KF69 79 EZX (MEXICO), KD37 79 EZX (US/CANADA)

Part Part name Qty. Part Part name Qty. Part Part name Qty.

Car-navigation
unit

1

Installation

instruction

1

Owner’s

manual

1

▼ REQUIRED TOOLS

☆Socket wrench (10mm) or Spanner wrench (10mm) ☆Torque wrench ☆Clean rag (soft cloth)

1. PARTS

• Before installation, verify that the kit includes all the following parts and that they are free of dirt, scratches,
or damage.

NOTE:

2. BEFORE INSTALLATION

• To prevent short related accidents while performing procedures, disconnect the negative battery cable
before beginning any work.

• When disconnecting the connector, hold the connector itself to remove while pressing the connector lock.

• Do not apply excessive force to the wiring harness as it could cause an open circuit.

• When locking connectors, listen for a click that will indicate they are securely locked.

• Be careful not to pinch the wiring harness. Otherwise, the harness may be broken.

WARNING

• Refer to the applicable Workshop Manual for removal and installation of vehicle parts. Not following the
procedures for removal/installation in the Workshop Manual could result in an accident or vehicle
malfunction.

• When the negative battery cable is removed, the clock, radio, trip meters and other memories will be
erased. Before performing work, record the content of the memory.

NOTE:

• When removing and installing vehicle parts, make sure they are clean with no scratches. Also, be sure to
cover the vehicle body with protectors or mats when removing/installing parts to prevent scratches and dirt.

CAUTION

3

Negative battery cable disconnection

1. Set the selector lever to P range.
(AT vehicles only)

2. Disconnect the negative battery cable and wrap tape around it
to insulate.

CAR-NAVIGATION UNIT INSTALLATION

Pocket Assy Removal

1. Grasp the pocket assy from the back side of the lower panel
and press it out to the vehicle rear.

2. Remove the harness clips.

3. Disconnect the connectors.

3. VEHICLE PARTS REMOVAL

•

When the negative battery cable is connected during

operation, it may cause electric shock or other personal
injuries. Disconnect the negative battery cable before
removal/installation.

WARNING

•

When removing/installing the parts, park the vehicle on

level ground and apply the side brake securely. Be sure to
turn the ignition switch off, otherwise the vehicle can move,
causing personal injury or vehicle damage.

WARNING

4. INSTALLATION

•

Be careful not to apply excessive force to the wiring

harness when removing the connectors.

CAUTION

Pock

et assy

H

arness clip

C

onnectors

Ne

g

ative battery cable

Pock

et assy

L

ower panel

Back side of
lower panel

Pocket
assy

Clip

s

Clip

s

4

Car-navigation unit Installation

1. Connect the USB, GPS antenna, and +B/ACC connectors to
the car-navigation unit.

2. Install the wiring harness clip.

3. Press the clips (4 locations) shown in the figure and install the
car-navigation unit to the lower panel.

1. Connect the negative battery cable and perform an operation check by referring to the owner’s manual
applicable to the vehicle.

2. If there is any malfunction, disconnect the negative battery cable and verify that each connector is properly
connected and the wiring harnesses are not damaged or pinched, then perform the operation check again. If it
does not operate normally, contact the dealer where the unit was purchased.

■ After installing the car-navigation unit, verify the connections of the GPS antenna, +B/ACC, and USB
connectors using the following procedure:

Connection verification of GPS antenna connector

1. Turn the ignition switch to the ON position.

2. After the opening screen ends, the Audio off screen is
displayed.

• Be careful not to press the car-navigation unit when
installing it.

CAUTION

H

arness clip

USB
connector

+B/ACC
connector

GPS

antenna

connector

C

ar-navigation unit

5. OPERATION CHECK

Audio off screen

C

ar-navigation unit

L

ower panel

Cli

ps

Cli

ps