Mazda KF69 79 EZX, KD37 79 EZX Instructions Manual

Page 1
1
GENUINE CAR-NAVIGATION UNIT
INSTALLATION INSTRUCTIONS
Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the contents of this booklet in order to properly install and use the car-navigation unit. Your safety depends on it. Keep these instructions with your vehicle records for future reference.
There are several WARNING and CAUTION sections in this booklet concerning
safety when installing or removing the car-navigation unit. Always read and follow them in order to prevent injuries, accidents, and possible damage to the vehicle.
WARNING: Indicates a situation in which serious injury or death could result if
the warning is ignored.
CAUTION: Indicates a situation in which bodily injury or damage to the vehicle
could result if the caution is ignored.
For areas indicating the tightening torque in this instruction manual, tighten to the specified torque using a torque wrench. For areas in which the tightening torque is indicated inside parentheses ( ), the tightening torque is indicated as a reference value, however tightening using a torque wrench is not necessary.
Do not modify the car-navigation unit.
Do not install the car-navigation unit in any way other than described in the following
instructions.
If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation.
If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before using it.
Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property that arise from the failure of the dealer or installer to follow these instructions.
To ensure safety and reliability of the work, installation, removal and disposal work
must be carried out by an Authorized Mazda Dealership.
Be careful not to lose removed parts, and be sure that they are kept free from scratches, grease or other dirt.
PART NAME: CAR-NAVIGATION UNIT
PART NUMBER: KF69 79 EZX (MEXICO)
KD37 79 EZX (US/CANADA)
VEHICLE: MAZDA CX-5
To the dealer
Please turn over these instructions to the customer after installation.
To the customer
Keep these instructions after installation. The instructions may be necessary for installing other optional parts or removal of this accessory.
Should the vehicle or this accessory be resold, always leave these instructions with it for the next owner.
WARNING
NOTE
00
GB
00
E
00
F
Page 2
2
PARTS LIST
KF69 79 EZX (MEXICO), KD37 79 EZX (US/CANADA)
Part Part name Qty. Part Part name Qty. Part Part name Qty.
Car-navigation unit
1
Installation
instruction
1
Owner’s
manual
1
REQUIRED TOOLS
Socket wrench (10mm) or Spanner wrench (10mm) ☆Torque wrench ☆Clean rag (soft cloth)
1. PARTS
Before installation, verify that the kit includes all the following parts and that they are free of dirt, scratches, or damage.
NOTE:
2. BEFORE INSTALLATION
To prevent short related accidents while performing procedures, disconnect the negative battery cable before beginning any work.
When disconnecting the connector, hold the connector itself to remove while pressing the connector lock.
Do not apply excessive force to the wiring harness as it could cause an open circuit.
When locking connectors, listen for a click that will indicate they are securely locked.
Be careful not to pinch the wiring harness. Otherwise, the harness may be broken.
WARNING
Refer to the applicable Workshop Manual for removal and installation of vehicle parts. Not following the procedures for removal/installation in the Workshop Manual could result in an accident or vehicle malfunction.
When the negative battery cable is removed, the clock, radio, trip meters and other memories will be erased. Before performing work, record the content of the memory.
NOTE:
When removing and installing vehicle parts, make sure they are clean with no scratches. Also, be sure to cover the vehicle body with protectors or mats when removing/installing parts to prevent scratches and dirt.
CAUTION
Page 3
3
Negative battery cable disconnection
1. Set the selector lever to P range. (AT vehicles only)
2. Disconnect the negative battery cable and wrap tape around it to insulate.
CAR-NAVIGATION UNIT INSTALLATION
Pocket Assy Removal
1. Grasp the pocket assy from the back side of the lower panel and press it out to the vehicle rear.
2. Remove the harness clips.
3. Disconnect the connectors.
3. VEHICLE PARTS REMOVAL
When the negative battery cable is connected during
operation, it may cause electric shock or other personal injuries. Disconnect the negative battery cable before removal/installation.
WARNING
When removing/installing the parts, park the vehicle on
level ground and apply the side brake securely. Be sure to turn the ignition switch off, otherwise the vehicle can move, causing personal injury or vehicle damage.
WARNING
4. INSTALLATION
Be careful not to apply excessive force to the wiring
harness when removing the connectors.
CAUTION
Pock
et assy
H
arness clip
C
onnectors
Ne
g
ative battery cable
Pock
et assy
L
ower panel
Back side of lower panel
Pocket assy
Clip
s
Clip
s
Page 4
4
Car-navigation unit Installation
1. Connect the USB, GPS antenna, and +B/ACC connectors to the car-navigation unit.
2. Install the wiring harness clip.
3. Press the clips (4 locations) shown in the figure and install the car-navigation unit to the lower panel.
1. Connect the negative battery cable and perform an operation check by referring to the owner’s manual applicable to the vehicle.
2. If there is any malfunction, disconnect the negative battery cable and verify that each connector is properly connected and the wiring harnesses are not damaged or pinched, then perform the operation check again. If it does not operate normally, contact the dealer where the unit was purchased.
After installing the car-navigation unit, verify the connections of the GPS antenna, +B/ACC, and USB connectors using the following procedure:
Connection verification of GPS antenna connector
1. Turn the ignition switch to the ON position.
2. After the opening screen ends, the Audio off screen is displayed.
Be careful not to press the car-navigation unit when installing it.
CAUTION
H
arness clip
USB connector
+B/ACC connector
GPS
antenna
connector
C
ar-navigation unit
5. OPERATION CHECK
Audio off screen
C
ar-navigation unit
L
ower panel
Cli
ps
Cli
ps
Page 5
5
3. Press the POWER/VOLUME dial to switch to the on screen.
4. Press the POWER/VOLUME dial and SEEK UP button at the same time on the Audio on screen (press POWER/VOLUME dial a little earlier).
5. After switching to the AUDIO system screen, touch the buttons in the order of “1”, “5” and “ENTER” on the screen.
6. After switching to the Vehicle and Navi Signal Check screen, touch “ “on the screen to switch the display screen to “NAVI GPS ANT”. Verify that “NAVI GPS ANT: OK” is displayed. If not OK, verify the connection condition again.
7. Press the POWER/VOLUME dial to switch to the AUDIO screen.
8. Switch the ignition off
POWER/VOLUME dial
SEEK UP b
utton
Audio on screen
POWER/VOLUME dial
Page 6
6
Connection verification of +B/ACC connector and USB connector
1. Turn the ignition switch to the ON position.
2. When the Audio off screen is displayed after the opening screen ends, press the NAV button.
3. When the screen in the figure on the left is displayed, the connection verification is completed. If it is not displayed, verify the connection condition again.
4. Switch the ignition off.
5. Remove the negative battery cable.
The procedure from this screen is performed by a user.
This procedure ends on this screen.
It is necessary to reset after this procedure. It is reset by
removing the negative battery cable.
NAV button
A
udio off screen
Ne
g
ative battery cable
Page 7
7
After connecting the negative battery cable, restore the vehicle functions using the following procedure.
Connect the negative battery cable
.
Tightening torque Nut4.05.0 Nm
Power window auto function
z If the battery is disconnected, the automatic full open/close feature of the power window is disabled.
This feature can be recovered by the following procedure.
1. Turn the ignition switch to the ON position.
2. Hold down the power window switch until the window is fully open.
3. Pull up the power window switch to close the window and continue to pull it up for about two seconds after it is fully closed.
4. If the feature does not function even after the ignition switch is turned off, contact an Authorized Mazda Dealer.
TPMS system
z If the battery is disconnected, the TPMS (Tire Pressure Monitoring System) initial setting is reset and the
system may not operate normally.
This feature can be recovered by the following procedure.
1. Adjust the tire pressure (verify tire pressure using label on body side with driver’s door open).
2. Turn the ignition switch to the ON position.
3. Press the TPMS (SET) switch (long-press it until TPMS warning light in meter flashes two times and a beep sounds one time).
4. Switch the ignition off.
5. If the TPMS warning light illuminates or flashes even though the above procedure has been performed, contact an Authorized Mazda Dealer.
CAUTION
Page 8
CAR-NAVIGATION UNIT
KF69 79 EZX (MEXICO) KD37 79 EZX (US/CANADA)
A. Vehicle parts reinstallation
Install removed vehicle parts in the reverse order of “VEHICLE PARTS REMOVAL”.
Check
B. Inspection after installation
Inspect the installed / reinstalled parts for the following items.
Check Item(○)
Inspection Parts
Clearance/Fit
Scratches/
Dirt/
Harness
interference
Installation/ Tightening/
Engagement
Operation check
Car-navigation unit
Negative battery cable
Power window auto function
TPMS system
○:Applicable
C. Important check items
Inspect the installed / reinstalled parts for the following items.
Section Parts Name Tightening torque
Check
Installation of the negative battery cable
Nut 4.05.0 Nm
Installation inspection sheet for car-navigation unit.
Date , , Vehicle. VIN.
Approved
Checked
Person in
charge
The term of validity for this sheet: 3 years.
MAZDA
CX-5
INSTALLATION INSPECTION SHEET
Make sure that the vehicle parts are clean before reinstalling. Clean
any dirty parts.
Verify that the connectors are securely connected.
CAUTION
Page 9
1
GENUINE CAR-NAVIGATION UNIT
INSTALLATION INSTRUCTIONS SUPPLEMENT
Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the contents of this booklet in order to properly install and use the car-navigation unit. Your safety depends on it. Keep these instructions with your vehicle records for future reference.
Due to changes in the vehicle, some additions and changes have been made to the con tent described in the existing installation instructions (KD37 79EZX/KF69 79 EZX). Please refer to the existing installation instructions (KD37 79EZX/KF69 79 EZX) for all other content that is not related to work procedures which are not covered in this supplement.
There are several WARNING and CAUTION sections in this booklet concerning safety when installing or removing the car-navigation unit. Always read and follow them in order to prevent injuries, accidents, and possible damage to the vehicle.
WARNING: Indicates a situation in which serious injury or death could result if
the warning is ignored.
CAUTION: Indicates a situation in which bodily injury or damage to the vehicle
could result if the caution is ignored.
For areas indicating the tightening torque in this instruction manual, tighten to the specified torque using a torque wrench. For areas in which the tightening torque is indicated inside parentheses ( ), the tightening torque is indicated as a reference value, however tightening using a torque wrench is not necessary.
Do not modify the car-navigation unit.
Do not install the car-navigation unit in any way other than described in the following
instructions.
If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation.
If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before using it.
Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property that arise from the failure of the dealer or installer to follow these instructions.
To ensure safety and reliability of the work, installation, removal and disposal work must be carried out by an Authorized Mazda Dealership.
Be careful not to lose removed parts, and be sure that they are kept free from scratches, grease or other dirt.
PART NAME: CAR-NAVIGATION UNIT
PART NUMBER: GJY3 79 EZX (MEXICO)
KJY2 79 EZX (US/CANADA)
VEHICLE: MAZDA CX-5
To the dealer
Please turn over these instructions to the customer after installation.
To the customer
Keep these instructions after installation. The instructions may be necessary for installing other optional parts or removal of this accessory.
Should the vehicle or this accessory be resold, always leave these instructions with it
for the next owner.
WARNING
NOTE
00
GB
00
E
00
F
Page 10
2
GPS CONNECTOR INSTALLATIONUS/CANADA only
Glove compartment removal
1. Push the glove compartment in the direction of the arrow (1) and hooks A.
2. Pull the stay damper in the direction of the arrow (2) shown in the figure and remove the hook B.
3. Pull down the glove compartment in the direction of the arrow (3).
4. Pull the glove compartment in the direction of the arrow (4) and remove it while detaching hooks C.
GPS connector installation
1. Disconnect the connector from the unit and connect it to the
connector shown in the figure.
2. Install the glove compartment in the reverse order of removal.
If the glove compartment is closed without being joined to the stay damper, the stay damper may be damaged. Verify that the stay damper is joined to the glove compartment before closeing the glove compartment.
CAUTION
(3)
(4)
Hook C
1. INSTALLATION
Hook A
Hook A
Glove compartment
Hook B
(1)
(1)
(2)
Stay damper
GPS connector
Page 11
3
Reset procedure
1. Touch "No”
2. Touch “Join Map Share”.
3. Touch “Continue”.
4. Touch “Y es”.
5. Touch “I agree”.
6. Touch the screen.
2. OPERATION CHECK
This procedure is in Step 3 of “Connection verification of +B/ACC connector and USB connector (Pg. 6)” of “5. OPERATION CHECK” of current INSTALLATION INSTRUCTIONS (KD37 79 EZX/KF69 79 EZX), and is implemented only if the “Continue” button is pressed by mistake and the screen advances too far.
Page 12
4
7. Touch “Setting”.
8. Touch the location shown in the figure.
9. Touch “Reset factory setting”.
10. Touch “Y es”.
1 1. Touch “Yes”.
12. Setting is finished when “Welcome” screen appears.
13. Switch the ignition off.
Page 13
CAR-NAVIGATION UNIT
GJY3 79 EZX (MEXICO) KJY2 79 EZX (US/CANADA)
A. Vehicle parts reinstallation
Install removed vehicle parts in the reverse order of “VEHICLE PARTS REMOVAL”.
Check
B. Inspection after installation
Inspect the installed / reinstalled parts for the following items.
Inspection Parts
Check Item(○)
Clearance/Fit
Scratches/
Dirt/
Harness
interference
Installation/ Tightening/
Engagement
Operation check
Car-navigation unit
Glove compartment
Negative battery cable
Power window auto function
TPMS system
○:Applicable
C. Important check items
Inspect the installed / reinstalled parts for the following items.
Section Parts Name Tightening torque
Check
Installation of the negative battery cable
Nut 4.05.0 Nm
Installation inspection sheet for car-navigation unit.
Date , , ehicle. VIN.
Approved
Checked
Person in
charge
The term of validity for this sheet: 3 years.
MAZDA
CX-5
INSTALLATION INSPECTION SHEET
Make sure that the vehicle parts are clean before reinstalling. Clean
any dirty parts.
Verify that the connectors are securely connected.
CAUTION
Loading...