Maytag YMET3800TW0, YMET3800TW1 Installation Guide

27"(69CM)ELECTRICWASHER/DRYER

INSTAILATIONINSTRUCTIONS

INSTRUCTIONSPOURL'INSTAILATIONDELA

p p

LAVEUSE/SECHEUSEELECTRIQUEDE27'(69CM)

Table of Contents /Table des mati_res

WASHER/DRYER SAFETY .............................. 2

INSTALLATION INSTRUCTIONS .................... 2

Tools and Parts ............................................. 2

Alternate Parts ............................................... 2

Location Requirements ................................. 3

Drain System ................................................. 4

Electrical Requirements ................................ 4

Venting Requirements ................................... 5

Remove Shipping Strap ................................ 6

Install Leveling Legs ...................................... 6

Connect the Drain Hose ................................ 6

Connect the Inlet Hoses ................................ 7

Secure the Drain Hose .................................. 8

Plan Vent System .......................................... 8

Install Vent System ...................................... 10

Level Washer/Dryer ..................................... 10

Connect Vent ............................................... 10

Complete Installation .................................. 10

S¢CURIT¢ DE LA LAVEUSE/SECHEUSE ....11

INSTRUCTIONS D'INSTALLATION ............... 11

Outillage et pieees ....................................... 11

Autres pieces ............................................... t 2

Exigences d'emplacement ......................... 12

Syst_me de vidange .................................... 13

Specifications _lectriques ............................ 14

Exigences concernant I'_vacuation ............. 15

Enlever la sangle d'exp_dition ..................... 16

Installation des pieds de nivellement ........... 16

Raccordement du tuyau de vidange ........... 16

Raccordement des tuyaux d'alimentation ..17

Immobilisation du tuyau de vidange ............ 18

Planification du systeme d'_vacuation ........ 18

Installation du systeme d'_vacuation ..........19

Nivellement de la laveuse/s_cheuse ........... 20

Raccordement du conduit d'_vacuation .....20

Achever I'installation .................................... 20

WASHER/DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow
instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

W10118291A

INSTALLATIONINSTRUCTIONS

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed

here.

Tools needed:

#2 Phillips and flat-blade
screwdriver

Adjustable wrench that
opens to 1" (2.5 cm) or
9/16"open-end wrench (for

adjusting washer/dryer
feet)

1/4"nut driver or socket
wrench

Tin snips (for new vent
installations)

Parts supplied:

Remove parts package from the washer basket. Check that all
parts were included.

• Caulking gun and
compound (for installing

new exhaust vent)

• Level

• Knife

• Vent clamps

• Pliers

• Scissors

• Wood block (for leveling)

• Ruler or measuring tape

Your installation may require additional parts. For information on
ordering, please refer to the toll free phone numbers on the front
page of the Washer/Dryer User Instructions.

If You Have You Will Need to Buy

Laundry tub or Sump pump system (if not already
standpipe taller than available)

96" (2.4 m)

1" (2.5 cm) diameter 2" (5 cm) diameter to 1" (2.5 cm)
standpipe diameter standpipe adapter, Part

Number 3363920

Overhead sewer Standard 20 gal. (76 L) 34" (86.4 cm)

tall drain tub or utility sink and sump

pump (available from local plumbing
suppliers)

Floor drain Siphon break, Part Number 285320,

additional drain hose, Part Number
285702 and connector kit,

Part Number 285442

Drain hose too short Drain hose, Part Number 285664 and

connector kit, Part Number 285442

Lint clogged drain Drain protector, Part Number 367031

Water faucets 2 longer water fill hoses:
beyond reach of fill 6 ft (1.8 m) Part Number 76314,

hoses 10 ft (3.0 m) Part Number 350008

D

A. Water inlet hoses (2)
B. Inlet hose flat washers (4)
C. Front leveling feet with nuts (2)

Parts needed for dryer:

Check local codes, electrical supply and venting, and read
"Electrical Requirements" and "Venting Requirements" before

purchasing parts.
Mobile home installations require metal exhaust system hardware

available for purchase from the dealer from whom you purchased
your washer/dryer. For further information, please reference the

"Assistance or Service" section of the Washer/Dryer User
Instructions.

D. Shipping strap (not in parts

bag. See "Remove Shipping
Strap. ")

E.Drain hose

£ Silver, double wire hose clamp

ExplosionHazard

Keepflammablematerialsandvapors,suchas
gasoline,awayfromdryer,

Failuretodosocanresultin death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. See
"Venting Requirements."

• Aseparate 30-amp circuit.

• A grounded electrical outlet located within 2 ft (61 cm) of
either side of the washer/dryer. See "Electrical Requirements."

• A sturdy floor to support the washer/dryer weight (washer/
dryer, water and load) of 500 Ibs (226.8 kg).

• A level floor with a maximum slope of 1" (2.5 cm) under entire
washer/dryer. Clothes may not tumble properly and automatic

sensor cycles may not operate correctly if washer/dryer is not
level. Installing on carpet is not recommended.

• A water heater set to deliver 120°F (49°C) water to the washer.

• Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of 5-100 psi
(34.5-689.6 kPa).

The washer/dryer must not be installed or stored in an area where
it will be exposed to water and/or weather.

Do not operate your washer in temperatures at or below 32°F
(0°C). Some water can remain in the washer and can cause
damage in low temperatures. See "Washer/Dryer Care" in the

Washer/Dryer User Instructions for winterizing information.
Do not operate your dryer at temperatures below 45°F (7°C). At

lower temperatures, the dryer might not shut off at the end of an
automatic cycle. This can result in longer drying times.

Check code requirements. Some codes limit, or do not permit,
installation of the washer/dryer in garages, closets, mobile homes,
or sleeping quarters. Contact your local building inspector.

Installation Clearances
The location must be large enough to allow the dryer door to open

fully.

Washer/Dryer Dimensions

71%"

(181.9 cm)

27"

(68.6 cm)

*Most installations require a minimum 5" (12.7 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting
Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this
washer/dryer. This washer/dryer has been tested for spacing of 0"

(0 cm) clearance on the sides. Recommended spacing should be
considered for the following reasons:

• Additional spacing should be considered for ease of
installation and servicing.

• Additional clearances might be required for wall, door and
floor moldings.

• Additional spacing on all sides of the laundry center is
recommended to reduce noise transfer.

For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are
acceptable.

Oo_,O

Wl L

$- (16_cm)

48in.2-

(310 cm2)

24in.2-

m

(166cm2)

r_,ll27,H, I1_,,

(2.6cm) (68,6cm)

*Required spacing

**Rear clearance may be 1" (2.5 cm) when house exhaust system

is lined up directly with dryer exhaust.

(2.6crn) (2.6crn) (81.3cm) (123 cm)

A

A. Recessed area

B. Side view - closet or confined area

C. Closet door with vents

B

Mobile Home - Additional Installation Requirements
This washer/dryer is suitable for mobile home installations.

The installation must conform to the Canadian Manufactured
Home Standard CAN/CSA-Z240 MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for
purchase from your dealer.

• Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer

exhaust opening.

The washer/dryer can be installed using the standpipe drain
system (floor or wall), the laundry tub drain system, or the floor

drain system. Select the drain hose installation method you need.
See "Alternate Parts."

Standpipe drain system - wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no less than

17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm)
diameter standpipe adapter kit is available. See "Alternate Parts."

The top of the standpipe must be at least 39" (99 cm) high and no
higher than 96" (2.4 m) from the bottom of the washer.

39"1

(99 cm)

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.
Failure to do so can result in death or electrical shock.

It is your responsibility

• To contact a qualified electrical installer.

• To be sure that the electrical connection is adequate and in
conformance with the Canadian Electrical Code, C22.1-latest

edition and local codes. A copy of the above codes standard
may be obtained from: Canadian Standards Association, 178
Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

• To supply the required 4 wire, single phase, 120/240 volt,
60 Hz., AC only electrical supply on a separate 30-amp circuit,
fused on both sides of the line. A time-delay fuse or circuit
breaker is recommended. Connect to an individual branch
circuit.

This dryer is equipped with a CSA International Certified
Power Cord intended to be plugged into a standard 14-30R

wall receptacle. The cord is 5 ft (1.52 m) in length. Be sure wall
receptacle is within reach of dryer's final location.

A

Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top

of the laundry tub must be at least 34" (86.4 cm) above the floor
and no higher than 96" (2.4 m) from the bottom of the washer.

Floor drain system (view D)

The floor drain system requires a siphon break that may be
purchased separately. See "Alternate Parts."

The siphon break must be a minimum of 28" (71 cm) from the
bottom of the washer. Additional hoses might be needed.

C

4-wire receptacle 14-30R

• Do not use an extension cord.

If you are using a replacement power supply cord, it is
recommended that you use Power Supply Cord Replacement
Part Number 9831317. For further information, please reference

the service numbers located in the Washer/Dryer User
Instructions.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected washer/dryer:
This washer/dryer must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for

electric current. This washer/dryer is equipped with a cord
having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance with

all local codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative or
personnel if you are in doubt as to whether the washer/dryer
is properly grounded. Do not modify the plug provided with
the washer/dryer: if it will not fit the outlet, have a proper
outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Fire Hazard

Use a heavy metal vent.
Do not use a plastic vent.

Do not use a metal foil vent.
Failure to fellow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this washer/dryer

MUST BE EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling or a concealed space of a building.

If using an existing vent system

Rigid metal vent

• For best drying performance, rigid metal vents are
recommended.

• Rigid metal vent is recommended to avoid crushing and
kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for
cleaning.

• Flexible metal vent must be fully extended and supported
when the dryer is in its final location.

• Remove excess flexible metal vent to avoid sagging and
kinking that may result in reduced airflow and poor

performance.

• Do not install flexible metal vent in enclosed walls, ceilings or
floors.

Elbows

45° elbows provide better airflow than 90° elbows.

• Clean lint from the entire length of the system and make sure
exhaust hood is not plugged with lint.

• Replace any plastic or metal foil vent with rigid or flexible
heavy metal vent.

• Review Vent system chart, Modify existing vent system if
necessary to achieve the best drying performance,

If this is a new vent system

Vent material

• Use a heaw metal vent. Do not use plastic or metal foil vent,

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be
used. DURASAFF Mventing products are recommended.

4" (10.2cm) heavymetal exhaust vent

DURASAFF Mvent products can be purchased from your
dealer or by calling Whirlpool Parts and Accessories. For more
information, see the "Assistance or Service" section of the
Washer/Dryer User Instructions.

Good Better

Clamps

Use clamps to seal all joints.
Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into the interior of the
duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

B

4" '

(10.2 era)

A. Louvered hood style

B.Box hood style

The angled hood style (shown here) is acceptable.

4"

(1 0.2 cm)__

P"_,_ 21/2''

(6.4 crn)

• An exhaust hood should cap the vent to keep rodents and
insects from entering the home.

• Exhaust hood must be at least 12" (30.5 cm) from the ground
or any object that may be in the path of the exhaust (such as
flowers, rocks or bushes, snow line, etc.).

• Do not use an exhaust hood with a magnetic latch.

Install the front leveling feet

1. Prop up the front of the washer/dryer about 4" (10.2 cm) with

a wood block or similar object. The block needs to support
the weight of the washer/dryer.

2. Screw the Iocknut onto each foot to within 1" (2.5 cm) of the
base.

+

1 "

(2.5 cm)

Improper venting can cause moisture and lint to collect
indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Excessive Weight Hazard

Use two or more people to move and install
washer/dryer.

Failure to do so can result in back or other injury.

To avoid floor damage, set washer/dryer onto cardboard before
moving across floor. Move washer/dryer close to its final location.

1. Do not cut yellow strap. Pull yellow strap firmly, until
completely removed from washer/dryer. There should be

2 cotter pins on the end of the shipping strap. Remove the
hang tag and pin from the vent pipe.

3=

Screw the feet into the correct holes at the front corner of the
washer/dryer until the nuts touch the washer.

NOTE: Do not tighten the nuts until the washer/dryer is level.

4.

Tilt the washer/dryer back and remove the wood block. Gently
lower the washer/dryer to the floor.

Proper connection of the drain hose protects your floors from
damage due to water leakage. To keep the drain hose from

coming off or leaking, it must be installed according to the
following instructions:

IMPORTANT: Toensure proper installation, this procedure must
be followed exactly.

1. Check the drain hose to see whether it is the proper length.

2. Wet the inside of the straight end of the drain hose with tap
water.

IMPORTANT: Do not use any lubricant other than water.

3. Squeeze ears of the silver, double-wire clamp with pliers to
open. Place clamp over the straight end of the drain hose

1A"(6.4 mm) from the end.

2. Tilt the washer/dryer forward. Move each of the 2 rear legs in
an up-down motion to check the self-adjusting leveling legs
for free movement. This is required for proper leveling. Gently

lower the washer/dryer to the floor.

3. Cut the shipping strap about 16" (40,6 cm) from the plug end.
Look for the words "CUT HERE." Discard end with cotter pins.
You will use the remaining piece of shipping strap to secure

the drain hose.

4 rnrn)

4. Open clamp. Twist hose back and forth while pushing onto
drain connector on the side of the washer/dryer. Continue until
hose contacts the ribbed stops on the cabinet.

5. Place clamp over the area marked "CLAMP" Release clamp.