Maytag MEDX500BW, MGDX500BW, YMEDX500BW, MEDB655DW Owner's Manual

SÉCHEUSE

ELECTRIC or GAS DRYER

USE AND CARE GUIDE

ÉLECTRIQUE ou À GAZ

GUIDE D’UTILISATION

ET D’ENTRETIEN

Para una versión de estas instrucciones en español, visite www.maytag.com

Table of Contents Table des matières

DRYER SAFETY ............................................................2

CHECK YOUR VENT SYSTEM

FOR GOOD AIR FLOW .................................................4

USE SENSOR DRY CYCLES FOR BETTER

FABRIC CARE AND ENERGY SAVINGS ......................4

CONTROL PANEL & FEATURES ..................................5

CYCLE GUIDE ............................................................... 6

USING YOUR DRYER ...................................................7

DRYER CARE ................................................................9

TROUBLESHOOTING ................................................. 11

WARRANTY .................................................................13

ASSISTANCE OR SERVICE .................... BACK COVER

SÉCURITÉ DE LA SÉCHEUSE ...................................14

VÉRIFICATION D’UNE CIRCULATION
D’AIR ADÉQUATE POUR LE SYSTÈME

D’ÉVACUATION .......................................................... 16

UTILISATION DES PROGRAMMES DE SÉCHAGE
PAR DÉTECTION POUR UN MEILLEUR SOIN
DU TISSU ET DAVANTAGE D’ÉCONOMIES

D’ÉNERGIE .................................................................. 16

TABLEAU DE COMMANDE

ET CARACTÉRISTIQUES ...........................................17

GUIDE DE PROGRAMMES ........................................18

UTILISATION DE LA SÉCHEUSE ............................... 19

ENTRETIEN DE LA SÉCHEUSE ................................. 21

DÉPANNAGE. ..............................................................24

GARANTIE. .................................................................. 26

ASSISTANCE

OU SERVICE. ........................COUVERTURE ARRIÈRE

W10594781A
W10594782A - SP

DRYER SAFETY

2

3

CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW

Maintain good air ow by:

n

Cleaning your lint screen before each load.

n

Replace plastic or foil vent material with 4" (102 mm)
diameter heavy, rigid vent material.

n

Use the shortest length of vent possible.

n

Use no more than four 90° elbows in a vent system;
each bend and curve reduces air ow.

Good air ow

Along with heat, dryers require good air ow to efciently
dry laundry. Proper venting will reduce your drying times
and improve your energy savings. See “Installation Instruc­tions.”

The venting system attached to the dryer plays a big role in
good air ow.

Service calls caused by improper venting are not covered
by the warranty and will be paid by the customer, regardless
of who installed the dryer.

n

n

n

Good Better

Remove lint and debris from the exhaust hood.
Remove lint from the entire length of the vent system at

least every 2 years. When cleaning is complete, be sure
to follow the “Installation Instructions” supplied with your
dryer for nal product check.

Clear away items from the front of the dryer.

USE SENSOR DRY CYCLES FOR BETTER FABRIC CARE
AND ENERGY SAVINGS

Use the SENSOR DRY cycles to provide the most energy savings and enhanced fabric care from the dryer. During SENSOR DRY
cycles, drying air temperature or moisture level are sensed in the load. This sensing occurs throughout the drying cycle and the
dryer shuts off when the load reaches the selected dryness. The Energy Preferred cycle will provide optimal energy savings.

With Timed Dry, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to over-drying.
Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying rack.

4

CONTROL PANEL & FEATURES

52 3 41

Not all features and options are available on all models.

1

TEMPERATURE

Select a drying temperature based on the fabrics in your
load. If you are unsure of the temperature to select for a
load, select the lower setting rather than the higher setting.

2

SIGNAL

The Signal produces an audible sound when the drying cycle
is nished. Promptly removing clothes at the end of the cycle
reduces wrinkling.

Turn the SIGNAL knob to select the desired setting (Off,
Low, or High).

3

CYCLE KNOB

Use Cycle Knob to select available cycles on your dryer.
Turn the knob to select a cycle for your laundry load. See
“Cycle Guide” for detailed descriptions of cycles.

Appearance may vary.

TIMED DRY

Will run the dryer for the specied time on the control.
On models with a selectable temperature knob, you
may choose a setting based on the fabrics in your load.
On some models, temperature is included in the cycle
selections. Drying time and temperature will depend on
your dryer model.

SENSOR DRY

Senses moisture in the load or air temperature and shuts
off when the load reaches the selected dryness level.
Gives the best drying in the shortest time. Drying time
will vary based on fabric type, load size, and temperature
setting.

4

WRINKLE CONTROL Feature

The WRINKLE CONTROL feature will run after your drying
cycle is complete. It periodically starts and stops the dryer,
tumbling the load without heat to help avoid wrinkling.

WRINKLE CONTROL automatically starts at the end of the
cycle. Opening the door will stop this feature.

n

Get up to 120 minutes of heat-free, periodic tumbling at
the end of a cycle. Turn the WRINKLE CONTROL knob
to OFF, 60 min., or 120 min. at any time before the cycle
has ended.

NOTE: A signal will sound periodically when the WRINKLE
CONTROL setting is selected, but only if the Signal is also
selected.

5

PUSH TO START

Press the PUSH TO START knob to start the dryer.

5

CYCLE GUIDE — SENSOR DRY CYCLES

SENSOR DRY - Senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level.

Choose ENERGY PREFERRED cycle for optimal energy savings.
Not all cycles and settings are available on all models.

Items to dry:

Dryness Level:

Temperature:

Available

Cycle Details:

Options:

Jeans, heavy work
clothes, towels

Work clothes, medium
weight fabrics, sheets

Casual, shirts, pants,
lightweight items,
synthetics, delicates,
athletic wear

NOTE: If loads do not seem as dry as you would like, select More Dry next time you dry a similar load. If loads seem drier than you
like, select Less Dry next time you dry a similar load.

More Dry

Energy Preferred

Less Dry

More Dry

Energy Preferred

Less Dry

More Dry

Energy Preferred

Less Dry

High

Medium or

Low

Low

Signal

Wrinkle Control

Signal

Wrinkle Control

Signal

Wrinkle Control

Automatic cycles give the best drying
in the shortest time. Drying time varies
based on fabric type, load size, and
dryness setting.

Select a drying temperature based on
the fabrics in your load. If you are unsure
of the temperature to select for a load,
select the lower setting rather than the
higher setting.

CYCLE GUIDE — TIMED DRY CYCLES

TIMED DRY - Will run the dryer for the specied time on the control.

Not all cycles and settings are available on all models.

Items to dry: Temperature:Cycle:

Available

Cycle Details:

Options:

Towels, bedding,

children’s clothing

Any load Freshen Up Any Signal Use low to medium temperature to

Rubber, plastic, heat

sensitive fabrics

Sanitize Sanitize Signal Extended high-heat drying cycle

Timed Dry

Air Fluff

Signal

intended to help sanitize items such as
bedding, towels, and baby wear. This
cycle is not recommended for all fabrics.
For best results, run cycle to completion,
do not interrupt.

smooth out wrinkles, such as those
found in clothes packed in a suitcase or
in items wrinkled from being left in the
dryer too long.

No heat drying.

Setting the Drying Temperature

If your dryer has multiple heat settings:
A High temperature setting may be used for drying

heavyweight items such as towels and work clothes.
A Low to Medium temperature setting may be used for drying

medium-weight items such as sheets, blouses, dresses,
underwear, permanent press fabrics, and some knits.

Use the Air Fluff (no heat) setting for foam, rubber, plastic, or
heat-sensitive fabrics.

Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures for

various loads, refer to the care label directions.

6

USING YOUR DRYER

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this dryer.

Before using your dryer, wipe the dryer drum with a damp cloth
to remove dust from storing and shipping.

1. Clean the lint screen

Clean the lint screen before each load. Pull the lint screen out
of its holder. Roll lint off the screen with your ngers. Do not
rinse or wash screen to remove lint. Push the lint screen rmly
back into place.

For additional cleaning information, see “Dryer Care”.

2. Load the dryer

3. Select the desired cycle

Select the desired cycle for your load. See the Cycle Guide
for more information about each cycle.

SENSOR DRY Cycles

You can select a different dryness level, depending on your
load, by turning the knob to dryness level.

Selecting More Dry, Energy Preferred, or Less Dry
automatically adjusts the dryness level of the fabrics at which
the dryer will shut off.

SENSOR DRY cycles give the best drying in the shortest time.
Drying time varies based on fabric type, load size, and dryness
setting. Choose Energy Preferred for optimal energy savings.
Less Dry removes less moisture and is used for loads you may
want to put on a hanger to complete drying.

More Dry removes more load moisture. Energy Preferred is
used for a starting point for SENSOR DRY cycles.

Place laundry in the dryer. Close the door.
Do not tightly pack the dryer; clothes should be able to tumble

freely.
NOTE: Your model may have a different door than the one

shown. Some models have drop down doors.

7

4. Set temperature

6. Select Wrinkle Control (if desired)

Select temperature by turning the knob to the desired position
or select the Sensor Dry cycle that has the temperature
included in the cycle selections. Turn the TEMPERATURE knob
to change the drying temperature setting. See “Setting the
Drying Temperature”.

NOTE: Not all options and settings are available with all cycles.

5. Select Signal (if desired)

Turn the SIGNAL knob to select the desired setting (Off, Low,
or High). The Signal produces an audible sound when the
drying cycle is nished. Promptly removing clothes at the end
of the cycle reduces wrinkling.

Select Wrinkle Control by turning the knob to the desired
position.

Get up to 120 minutes of heat-free, periodic tumbling at the
end of a cycle. Turn the WRINKLE CONTROL knob to OFF,
60 min., or 120 min. at any time before the cycle has ended.

NOTE: Not all options and settings are available with all
cycles.

7. Press PUSH TO START to begin

cycle

Push and hold the PUSH TO START knob to begin the cycle.

DRYING RACK

To purchase a drying rack for your dryer, please refer to
“Assistance or Service” on the back cover of the manual or
contact the dealer from whom you purchased your dryer.

Part Number Accessory

3406839 Drying rack - ts 29" Super Capacity Plus

8

DRYER CARE

Cleaning the dryer location

Keep dryer area clear and free from items that would
block the air ow for proper dryer operation. This includes
clearing piles of laundry in front of the dryer.

Cleaning the dryer interior

To clean dryer drum

1. Apply a liquid, nonammable household cleaner to the

stained area of the drum and rub with a soft cloth until
stain is removed.

2. Wipe drum thoroughly with a damp cloth.

3. Tumble a load of clean cloths or towels to dry the drum.

NOTE: Garments that contain loose dyes, such as denim

blue jeans or brightly colored cotton items, may discolor the
dryer interior. These stains are not harmful to your dryer and
will not stain future loads of clothes. Dry these items inside
out to avoid drum staining.

Removing accumulated lint

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often,
depending on dryer usage. Cleaning should be done by a
qualied servicer.

From the Exhaust Vent

Lint should be removed every 2 years, or more often,
depending on dryer usage.

Cleaning the lint screen

Every load cleaning

The lint screen is located in the dryer. A screen blocked by
lint can increase drying time.

To clean:

1. Pull the lint screen out of its holder. Roll lint off the

screen with your ngers. Do not rinse or wash screen to
remove lint. Wet lint is hard to remove.

2. Push the lint screen rmly back into place.

IMPORTANT:

n

Do not run the dryer with the lint screen loose,
damaged, blocked, or missing. Doing so can cause
overheating and damage to both the dryer and fabrics.

n

If lint falls off the screen into the dryer during removal,
check the exhaust hood and remove the lint. See
“Venting Requirements.”

As needed cleaning

Laundry detergent and fabric softener residue can build
up on the lint screen. This buildup can cause longer drying
times for your clothes, or cause the dryer to stop before
your load is completely dry. The screen is probably clogged
if lint falls off while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months,
or more frequently, if it becomes clogged due to a residue
buildup.

To wash:

1. Roll lint off the screen with your ngers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent.

Scrub lint screen with the brush to remove residue
buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Reinstall

screen in dryer.

9