How it Works
Maytag
Loading...
W10285880A
User Manual
32 pgs826.16 Kb0

Maytag W10285880A User Manual

BEVERAGE CENTER
Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-688-9900 , or visit our website at www.maytag.com
In Canada, for assistance or service call: 1-800-807-6777, or visit our website at www.maytag.ca
REFRIGERADOR PARA BEBIDAS
Manual de uso y cuidado
Para consultas respecto a características, operación/desempeño, partes, accesorios o servicio, llame al: 1-800-688-9900
o visite nuestra página de internet en www.maytag.com
RÉFRIGÉRATEUR POUR BOISSONS
Guide d’utilisation et d’entretien
Au Canada, pour assistance ou service, composer le 1-800-807-6777 ou visitez notre site web à... www.maytag.ca
Table of Contents/Índice/Table des matières................................2
W10285880A - 8336411962010
TABLE OF CONTENTS
BEVERAGE CENTER SAFETY ......................................................3
Proper Disposal of Your Old Refrigerated Appliance..................3
INSTALLATION INSTRUCTIONS..................................................4
Location Requirements................................................................4
Electrical Requirements ...............................................................4
Unpack the Beverage Center.......................................................4
Reverse Door Swing ....................................................................5
Door Closing.................................................................................6
Base Grille ....................................................................................6
BEVERAGE CENTER USE.............................................................6
Normal Sounds ............................................................................6
Using the Control .........................................................................7
Beverage/Wine Racks..................................................................7
ÍNDICE
Stocking the Beverage Center.....................................................8
Lighting the Beverage Center ......................................................8
BEVERAGE CENTER CARE ..........................................................8
Cleaning........................................................................................8
Changing the Light Bulb...............................................................9
Vacation and Moving Care...........................................................9
TROUBLESHOOTING ....................................................................9
ASSISTANCE OR SERVICE.........................................................11
In the U.S.A. ...............................................................................11
In Canada ...................................................................................11
Accessories ................................................................................11
WARRANTY ..................................................................................12
SEGURIDAD DEL REFRIGERADOR PARA BEBIDAS ..............13
Cómo deshacerse adecuadamente de
su aparato refrigerado viejo .......................................................13
INSTRUCCIONES DE INSTALACIÓN.........................................14
Requisitos de ubicación.............................................................14
Requisitos eléctricos..................................................................14
Desempaque del refrigerador para bebidas..............................14
Cambio del sentido de apertura de la puerta............................15
Cómo cerrar la puerta ................................................................16
Rejilla de la base ........................................................................16
USO DEL REFRIGERADOR PARA BEBIDAS ............................16
Sonidos normales ......................................................................16
Uso del control...........................................................................17
TABLE DES MATIÈRES
SÉCURITÉ DU RÉFRIGÉRATEUR POUR BOISSONS ..............23
Mise au rebut de votre vieil appareil réfrigéré ...........................23
INSTRUCTIONS D’INSTALLATION ............................................24
Exigences d'emplacement.........................................................24
Spécifications électriques..........................................................24
Déballage du réfrigérateur pour boissons .................................24
Inversion du sens de l'ouverture de la porte .............................25
Fermeture de la porte.................................................................26
Grille de la base..........................................................................26
UTILISATION DU RÉFRIGÉRATEUR POUR BOISSONS..........26
Sons normaux ............................................................................26
Utilisation de la commande .......................................................27
Casiers à vin/boissons...............................................................27
Portabebidas/portabotellas........................................................17
Cómo almacenar en el refrigerador para bebidas.....................17
Cómo iluminar el refrigerador para bebidas ..............................18
CUIDADO DEL REFRIGERADOR PARA BEBIDAS ...................18
Limpieza .....................................................................................18
Cómo cambiar el foco................................................................19
Cuidado durante las vacaciones y mudanzas...........................19
SOLUCIÓN DE PROBLEMAS......................................................19
AYUDA O SERVICIO TÉCNICO...................................................21
En los EE.UU. .............................................................................21
En Canadá..................................................................................21
Accesorios..................................................................................21
GARANTÍA.....................................................................................22
Stockage dans le réfrigérateur pour boissons...........................27
Éclairage du réfrigérateur pour boissons...................................28
ENTRETIEN DU RÉFRIGÉRATEUR POUR BOISSONS ............28
Nettoyage ...................................................................................28
Changement de l'ampoule d'éclairage......................................29
Précautions à prendre pour les vacances et avant un
déménagement ..........................................................................29
DÉPANNAGE.................................................................................29
ASSISTANCE OU SERVICE.........................................................31
Aux États-Unis............................................................................31
Au Canada..................................................................................31
Accessoires ................................................................................31
GARANTIE.....................................................................................32
2
BEVERAGE CENTER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
precautions:
■
Plug into a grounded 3 prong outlet.
■
Do not remove ground prong.
■
Do not use an adapter.
■
Do not use an extension cord.
■
Disconnect power before servicing.
■
Replace all parts and panels before operating.
To reduce the risk of fire, electric shock, or injury when using your beverage center, follow these basic
SAVE THESE INSTRUCTIONS
follow instructions.
can be killed or seriously injured if you don't
You instructions.
■
Remove door or drawer(s) from your old refrigerated
appliance.
■
Use nonflammable cleaner.
■
Keep flammable materials and vapors, such as gasoline, away from beverage center.
■
Use two or more people to move and install beverage center.
follow
Proper Disposal of Your Old
Refrigerated Appliance
WARNING
Suffocation Hazard
Remove door or drawer(s) from your old refrigerated appliance.
Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned beverage centers are still dangerous – even if they will sit for “just a few days.” If you are getting rid of your old beverage center, please follow these instructions to help prevent accidents.
Before You Throw Away Your Old Refrigerated Appliance:
■ Take off the door.
■ Leave the racks and shelves in place so that children may not
easily climb inside.
3
INSTALLATION INSTRUCTIONS
Location Requirements
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from beverage center.
Failure to do so can result in death, explosion, or fire.
To ensure proper ventilation for your beverage center, allow for a ¹/₄" (6.35 mm) space on each side and at the top. When installing your beverage center next to a fixed wall, leave 2¹⁄₂" (6.35 cm) minimum clearance on the hinge side to allow for the door to swing open.
NOTE: It is recommended that you do not install the beverage center near an oven, radiator, or other heat source. Do not install in a location where the temperature will fall below 55°F (13°C). For best performance, do not install the beverage center behind a cabinet door or block the base grille.
¹⁄₄" (6.35 mm)
Electrical Requirements
WARNING
Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your beverage center into its final location, it is important to make sure you have the proper electrical connection.
Recommended grounding method
A 115 Volt, 60 Hz., AC only, 15– or 20–amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your beverage center be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.
NOTE: Before performing any type of installation, cleaning, or removing a light bulb, unplug beverage center or disconnect power.
Unpack the Beverage Center
WARNING
Excessive Weight Hazard
2¹⁄₂" (6.35 cm)
4
Use two or more people to move and install beverage center.
Failure to do so can result in back or other injury.
Remove the Packaging
■ Remove tape and glue residue from surfaces before turning
on the beverage center. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
■ Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your beverage center. For more information, see “Beverage Center Safety.”
■ Dispose of/recycle all packaging materials.
When Moving Your Beverage Center:
C
C D
B
A
C
Your beverage center is heavy. When moving the appliance for cleaning and service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the appliance straight out when moving it. Do not wiggle or “walk” the appliance when trying to move it, as floor damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside of your beverage center before using it. See the cleaning instructions in “Beverage Center Care.”
Important information to know about glass shelves and covers:
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.
Front View
B
A
A. Cover B. Bottom of beverage
center cabinet
C. Bottom hinge D. Washer
7. Remove the two screws fastening the door stop spacer and
the door stop to the bottom of the beverage center door.
8. Move the door stop spacer and the door stop to the opposite
side and fasten with the two screws. Completely tighten the screws.
Bottom View
Reverse Door Swing
(optional)
Tools Needed: Phillips screwdriver
1. Unplug beverage center or disconnect power.
2. Remove the screws from each side of the top of the beverage
center cabinet and set aside.
NOTE: There are seven screws total. Do not discard.
3. Remove the hinge cover and washer and set aside. Top View
A
B
A. Top of beverage center cabinet B. Hinge cover C. Washer
4. Lift the door straight up and off of the bottom hinge.
5. Remove the screws fastening the bottom hinge and cover to
the bottom of the beverage center cabinet. There are five screws total.
6. Move the bottom hinge and cover each to the opposite side
of the bottom of the beverage center cabinet. Completely tighten the five screws.
A. Bottom of beverage center door B. Door stop spacer C. Door stop
9. Place the washer onto the bottom hinge, then install the
beverage center door onto the washer and hinge pin.
A
B
A. Bottom hinge washer B. Bottom hinge
10. Align the top hinge washer with the hinge hole in the top of
the door. Then, insert the top hinge pin through the washer and into the hinge hole.
11. Fasten the top hinge cover with three screws and move the
remaining four screws to the opposite side. Completely tighten the seven screws.
BA
A. Top hinge washer B. Top hinge
5
Door Closing
Door Closing
Your beverage center has four leveling legs. If your beverage center seems unsteady or you want the door to close more easily, adjust the beverage center’s tilt using the instructions below.
WARNING
Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,
fire, or electrical shock.
Base Grille
Tools Needed: Phillips screwdriver
Remove the Base Grille
1. Open the beverage center door.
2. Using a Phillips screwdriver, remove the two screws. Push
both tabs in toward the center to release the base grille from the beverage center.
BAA
A. Tabs B. Screws
3. Remove the base grille.
1. Plug into a grounded 3 prong outlet.
WARNING
Excessive Weight Hazard
Use two or more people to move and install beverage center.
Failure to do so can result in back or other injury.
2. Move the beverage center into its final location.
3. Turn the leveling legs to the right to lower the beverage center
or turn the leveling legs to the left to raise it. It may take several turns of the leveling legs to adjust the tilt of the beverage center.
NOTE: Having someone push against the top of the beverage center takes some weight off the leveling legs. This makes it easier to adjust the leveling legs.
4. Make sure that the door closes as easily as you like. If not, tilt
the beverage center slightly more to the rear by turning both front leveling screws to the left. It may take several more turns, and you should turn both leveling legs the same amount.
Replace the Base Grille
1. Open the beverage center door.
2. Position the base grille so that both tabs align and the base
grille snaps into place. Replace the two screws. Tighten the screws.
BEVERAGE CENTER USE
Normal Sounds
Your new beverage center may make sounds that your old one didn’t make. Because the sounds are new to you, you might be concerned about them. Most of the new sounds are normal. Hard surfaces, such as the flooring and surrounding structures, can make the sounds seem louder. The following describes the kinds of sounds and what may be making them.
■ Your beverage center is designed to run more efficiently to
keep your food items at the desired temperatures and to minimize energy usage. The high efficiency compressor and fans may cause your beverage center to run longer than your old one. You may also hear a pulsating or high-pitched sound from the compressor or fans adjusting to optimize performance.
■ Rattling noises may come from the flow of refrigerant or items
stored inside the beverage center.
■ As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing in your beverage center.
■ You may hear water running into the drain pan when the
beverage center is defrosting.
■ You may hear clicking sounds when the beverage center
starts or stops running.
6
Using the Control
C
D
For your convenience, your beverage center control is preset at the factory. When you first install your beverage center, make sure that the control is still preset to the mid-setting as shown.
Adjusting Controls
The mid-setting indicated in the previous section should be correct for normal usage. The control is set correctly when beverages are as cold as you like.
If you need to adjust the temperature, wait at least 24 hours between adjustments and then recheck the temperature.
To make the beverage center colder, adjust the control to the next higher setting. To make the beverage center less cold, adjust the control to the next lower setting.
Temperature Separator (Temperature Display)
The temperature separator displays the current temperatures (Fahrenheit or Celsius) for the upper and lower zones (compartments) of the beverage center. To adjust the temperature settings, see “Adjusting Controls” earlier in this section.
Beverage/Wine Racks
Upper Wine Rack
To remove the wine rack:
1. Remove all bottles from the wine rack.
2. Lift the wine rack straight up slowly until it clears all four
resting posts. Pull the rack out of the compartment.
To replace the wine rack: IMPORTANT: The wine rack hooks should be facing down when
the wine rack is installed.
1. Place the wine rack into the compartment above the four
resting posts and slide the rack back until it is aligned with all four resting posts.
2. Push down gently on the rack until the wine rack hooks snap
firmly onto the two rear posts and the front of the rack is resting on the two front posts.
Lower Wine Rack
To remove the wine rack:
1. Remove all bottles from the wine rack.
2. Slowly, lift the wine rack straight up until it clears the two rear
resting posts. Pull the rack out of the compartment.
To replace the wine rack: IMPORTANT: The wine rack hooks should be facing down when
the wine rack is installed.
1. Slide the wine rack into the compartment until the two hooks
on the back of the rack are aligned with the two rear resting posts.
2. Push down gently on the rack until the hooks on the back of
the rack snap firmly onto the two rear posts. Rest the front of the rack on the compartment floor.
Side View
A B C D
A. Dimmer B. Upper zone display
C. Lower zone display D. Fahrenheit/Celsius
A
B
A. Upper wine rack B. Lower wine rack
C. Rack hook D. Resting post
7
Stocking the Beverage Center
1. Start stocking the beverage center with the bottom display
rack.
BEVERAGE CENTER CARE
Cleaning
WARNING
2. Place juices, sodas or other canned beverages on the glass
shelves.
Lighting the Beverage Center
The beverage center has an interior light that comes on any time the door is opened. You may also turn the light on at any time by opening the door and pressing the exterior switch located beside the temperature control knob on the base grille.
NOTE: Leaving the light on for an extended period of time will slightly increase the temperature of the beverage center.
Explosion Hazard Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.
Clean the beverage center about once a month to avoid odor buildup. Wipe up spills immediately.
To clean your beverage center:
1. Unplug beverage center or disconnect power.
2. Remove all racks and shelves from inside the beverage
center.
3. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.
■ Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.
■ To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda (2 tbs to 1 qt [26 g to 0.95 L] of water).
4. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners containing chlorine. These can scratch or damage materials. Dry thoroughly with a soft cloth.
NOTE: To keep your stainless steel beverage center looking like new and to remove minor scuffs or marks, it is suggested that you use the manufacturer’s approved Stainless Steel Cleaner and Polish. To order the cleaner, see “Accessories.”
IMPORTANT: This cleaner is for stainless steel parts only! Do not allow the Stainless Steel Cleaner and Polish to come
into contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets. If unintentional contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth.
5. Replace the racks and shelves.
6. Clean the condenser coils regularly. They are located behind
the base grille. Coils may need to be cleaned as often as every other month. This may help save energy.
■ Remove the base grille. See “Base Grille.”
■ Use a vacuum cleaner with an extended attachment to
clean the condenser coils when they are dusty or dirty.
■ Replace the base grille.
7. Plug in beverage center or reconnect power.
8
Changing the Light Bulb
NOTE: Not all appliance bulbs will fit your beverage center. Be sure to replace the bulb with one of the same size, shape, and wattage.
To change the light bulb:
1. Unplug beverage center or disconnect power.
2. Using a Phillips screwdriver, remove the screw located at the
back of the light shield. Pull the light shield back to remove the tabs from the appliance. Remove the light shield.
Vacation and Moving Care
Vacations
If you choose to turn the beverage center off before you leave, follow these steps.
1. Remove all wine bottles from the beverage center.
2. Unplug the beverage center.
3. Clean the beverage center. See “Cleaning.”
4. Tape a rubber or wood block to the top of the door to prop it
open far enough for air to get in. This stops odor and mold from building up.
B
A
A. Light shield B. Tabs
C. Screw
3. Replace the bulb.
4. Reinstall the light shield by inserting the tabs. Align the holes
and insert the screw. Tighten the screw.
5. Plug in beverage center or reconnect power.
C
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Your beverage center will not operate
WARNING
Moving
When you are moving your beverage center to a new home, follow these steps to prepare it for the move.
1. Remove all wine bottles from the beverage center.
2. Unplug the beverage center.
3. Clean, wipe, and dry it thoroughly.
4. Take out all removable parts, wrap them well, and tape them
together so they don’t shift and rattle during the move.
5. Tape the doors shut and tape the power cord to the beverage
center.
When you get to your new home, put everything back and refer to the “Installation Instructions” section for preparation instructions.
■ Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit.
■ Is the Beverage Center Control turned to the OFF
position? See “Using the Control.”
The lights do not work
Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,
fire, or electrical shock.
■ Is the power supply cord unplugged? Plug into a grounded
3 prong outlet.
■ Is a light bulb loose in the socket? Unplug beverage center
or disconnect power. Gently remove the bulb and reinsert. Plug in beverage center or reconnect power.
■ Has a light bulb burned out? Replace with an appliance
bulb of the same wattage, size, and shape. See “Changing the Light Bulb.”
9
The motor seems to run too much
■ Is the temperature outside hotter than normal? Expect the
motor to run longer under warm conditions. At normal temperatures, expect your motor to run about 40% to 80% of the time. Under warmer conditions, expect it to run even more of the time.
■ Is the door opened often? Expect the motor to run longer
when this occurs. In order to conserve energy, try to get everything you need out of the beverage center at once, keep wine bottles positioned label side up so that they are easy to find, and close the door as soon as the wine is removed.
■ Is the control set correctly for the surrounding
conditions? See “Using the Control.”
■ Is the door closed completely? Push the door firmly shut. If
it will not shut all the way, see “The door will not close completely” later in this section.
■ Are the condenser coils dirty? This obstructs air transfer
and makes the motor work harder. Clean the condenser coils. See “Cleaning.”
The door is difficult to open
WARNING
Explosion Hazard Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.
■ Is the gasket dirty or sticky? Clean the gasket and the
surface that it touches. Rub a thin coat of paraffin wax on the gasket following cleaning.
The door will not close completely
Temperature is too warm
■ Is the door opened often? Be aware that the beverage
center will warm when this occurs. In order to keep the beverage center cool, try to get everything you need out of the beverage center at once, keep wine bottles positioned label side up so that they are easy to find, and close the door as soon as the wine is removed.
■ Is the control set correctly for the surrounding
conditions? See “Using the Control.”
■ Is the base grille blocked? For best performance, do not
install the beverage center behind a cabinet door or block the base grille.
There is interior moisture buildup
■ Is the door opened often? To avoid humidity buildup, try to
get everything you need out of the beverage center at once, keep wine bottles positioned label side up so that they are easy to find, and close the door as soon as the wine is removed. When the door is opened, humidity from the room air enters the beverage center. The more often the door is opened, the faster humidity builds up, especially when the room itself is very humid.
■ Is it humid? It is normal for moisture to build up inside the
beverage center when the air is humid.
■ Is the control set correctly for the surrounding
conditions? See “Using the Control.”
■ Are the racks or shelves out of position? Put the racks or
shelves back into their correct positions. See “Beverage Center Use” for more information.
WARNING
Explosion Hazard Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.
■ Is the gasket sticking? Clean the gasket and the surface
that it touches. Rub a thin coat of paraffin wax on the gasket following cleaning.
10
Loading...
+ 22 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use