Maytag W10112937A User Manual

ELECTRIC DRYER

USE & CARE GUIDE

SECADORA ELÉCTRICA

MANUAL DE USO Y CUIDADO

SÉCHEUSE ÉLECTRIQUE

GUIDE D’UTILISATION ET D’ENTRETIEN

FOR QUESTIONS ABOUT FEATURES, OPERATION/PERFORMANCE,

PARTS, ACCESSORIES OR SERVICE CALL: 1.800.688.9900

IN CANADA, CALL: 1.800.807.6777

VISIT OUR WEBSITE AT WWW.MAYTAG.COM

IN CANADA, WWW.MAYTAG.CA

W10112937A

SI TIENE PREGUNTAS RESPECTO A LAS CARACTERÍSTICAS,

FUNCIONAMIENTO, RENDIMIENTO, PARTES, ACCESORIOS O

SERVICIO TÉCNICO, LLAME AL: 1.800.688.9900

EN CANADÁ, LLAME AL: 1.800.807.6777

VISITE NUESTRO SITIO WEB EN

WWW.MAYTAG.COM

EN CANADÁ, WWW.MAYTAG.CA

AU CANADA, POUR ASSISTANCE, INSTALLATION OU SERVICE,

COMPOSEZ LE : 1.800.807.6777

OU VISITEZ NOTRE SITE INTERNET À

WWW.MAYTAG.CA

TABLE OF CONTENTS

DRYER SAFETY......................................................................3

INSTALLATION INSTRUCTIONS .........................................4

Tools and Parts...................................................................4

Optional Pedestal...............................................................4

Location Requirements.......................................................5

Electrical Requirements - U.S.A. Only................................7

Electrical Requirements - Canada Only..............................9

Electrical Connection - U.S.A. Only.................................10

Venting Requirements......................................................16

Plan Vent System..............................................................17

Install Vent System ...........................................................19

Install Leveling Legs .........................................................19

Connect Vent ...................................................................19

Level Dryer ......................................................................19

Reverse Door Swing.........................................................20

Complete Installation .......................................................22

DRYER USE..........................................................................23

Starting Your Dryer...........................................................23

Stopping or Restarting Your Dryer....................................24

Lock Controls...................................................................24

Drying and Cycle Tips......................................................25

Status Lights......................................................................25

Cycles ..............................................................................26

Additional Features ..........................................................27

Changing Cycles, Options and Modifiers.........................27

Drying Rack Option.........................................................28

DRYER CARE......................................................................29

Cleaning the Dryer Location ............................................29

Cleaning the Lint Screen ..................................................29

Cleaning the Dryer Interior...............................................29

Removing Accumulated Lint............................................29

Vacation and Moving Care ..............................................30

TROUBLESHOOTING.........................................................30

ASSISTANCE OR SERVICE...................................................32

WARRANTY ........................................................................33

ÍNDICE

SEGURIDAD DE LA SECADORA........................................ 35

INSTRUCCIONES DE INSTALACIÓN ................................ 36

Herramientas y piezas ..................................................... 36

Pedestal opcional ............................................................ 37

Requisitos de ubicación .................................................. 37

Requisitos eléctricos - Sólo en EE. UU............................. 39

Conexión eléctrica - Sólo en EE. UU............................... 41

Requisitos de ventilación................................................. 47

Planificación del sistema de ventilación.......................... 48

Instalación del sistema de ventilación ............................. 50

Instalación de las patas niveladoras................................. 50

Conexión del ducto de escape ........................................ 51

Nivelación de la secadora ............................................... 51

Cómo invertir el cierre de la puerta................................. 51

Complete la instalación................................................... 53

USO DE LA SECADORA..................................................... 54

Puesta en marcha de la secadora..................................... 54

Detención o reanudación de la marcha de la

secadora.......................................................................... 55

Bloquear los controles..................................................... 55

Sugerencias de ciclos y secado........................................ 56

Luces de estado ............................................................... 56

Ciclos .............................................................................. 57

Características adicionales............................................... 58

Cambio de ciclos, opciones y modificadores .................. 59

Opción de estante de secado .......................................... 59

CUIDADO DE LA SECADORA........................................... 60

Limpieza del lugar donde está la secadora...................... 60

Limpieza del filtro de pelusa............................................ 60

Limpieza del interior de la secadora................................ 61

Eliminación de pelusa acumulada................................... 61

Cuidado para las vacaciones y la mudanza..................... 61

SOLUCIÓN DE PROBLEMAS ............................................. 62

AYUDA O SERVICIO TÉCNICO......................................... 64

GARANTÍA ......................................................................... 65

TABLE DES MATIÈRES

SÉCURITÉ DE LA SÉCHEUSE............................................... 67

INSTRUCTIONS D’INSTALLATION ...................................68

Outillage et pièces........................................................... 68

Piédestal facultatif............................................................69

Exigences d'emplacement................................................ 69

Spécifications électriques - Pour le Canada

seulement ........................................................................ 72

Exigences concernant l'évacuation.................................. 73

Planification du système d’évacuation............................. 74

Installation du système d’évacuation................................76

Installation des pieds de nivellement ...............................76

Raccordement du conduit d’évacuation ..........................77

Mise à niveau de la sécheuse........................................... 77

Inversion du sens d'ouverture de la porte ........................77

Achever l'installation .......................................................79

UTILISATION DE LA SÉCHEUSE ........................................80

Mise en marche de la sécheuse .......................................80

Arrêt ou remise en marche de la sécheuse.......................81

Verrouillage des commandes...........................................81

Conseils pour le séchage et les programmes....................82

Témoins lumineux ...........................................................82

Programmes.....................................................................83

Caractéristiques supplémentaires..................................... 84

Changement des programmes, options et

modificateurs ...................................................................84

Option de grille de séchage.............................................85

ENTRETIEN DE LA SÉCHEUSE ...........................................86

Nettoyage de l'emplacement de la sécheuse ...................86

Nettoyage du filtre à charpie............................................ 86

Nettoyage de l’intérieur de la sécheuse............................87

Retrait de la charpie accumulée....................................... 87

Précautions à prendre pour les vacances et avant

un déménagement ...........................................................87

DÉPANNAGE ......................................................................88

ASSISTANCE OU SERVICE.................................................. 90

GARANTIE ..........................................................................91

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

including the following:

■

Read all instructions before using the dryer.

■

Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

■

Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, drycleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.

■

Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.

■

Before the dryer is removed from service or discarded, remove the door to the drying compartment.

■

Do not reach into the dryer if the drum is moving.

■

Do not install or store the dryer where it will be exposed to the weather.

■

Do not tamper with controls.

To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

follow instructions.

can be killed or seriously injured if you don't

You instructions.

■

Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.

■

Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

■

Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

■

Clean lint screen before or after each load.

■

Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

■

The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.

■

See installation instructions for grounding requirements.

SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■ Flat-blade screwdriver

■ #2 Phillips screwdriver

■ Adjustable wrench that opens to 1"

(2.54 cm) or hex-head socket wrench (for adjusting dryer feet)

■ Wire stripper (direct wire installations)

■ Level

Parts supplied

Remove parts package from dryer drum. Check that all parts are included.

4 Leveling legs

NOTE: Do not use leveling legs if installing the dryer on a pedestal.

Parts needed

Check local codes. Check existing electrical supply and venting. See “Electrical Requirements” and “Venting Requirements” before purchasing parts.

■ For close-clearance installations between 28.65" (72.77 cm) and 34.15" (86.74 cm), see

“Plan Vent System” section for venting requirements.

■ Vent clamps

■ Caulking gun and compound (for

installing new exhaust vent)

■ Tin snips (new vent installations)

■ ¼" nut driver or socket wrench

(recommended)

■ Tape mea sur e

Optional Pedestal

Are you placing the dryer on a pedestal? You have the option of purchasing pedestals of different heights separately for this dryer. You may select a 10" (25.4 cm) pedestal or a

15.5" (39.4 cm) pedestal with a storage drawer. The pedestal will add to the total height of the dryer for a total height of approximately 46" (116.8 cm) or 51.5" (130.8 cm), respectively.

For a garage installation, you will need to place the 10" (25.4 cm) pedestal at least 9" (22.9 cm) above the floor. You will need to place the 15.5" (39.4 cm) pedestal at least 3" (7.6 cm) above the floor.

Optional pedestal (15.5" [39.4 cm] model shown)

The pedestals are available in several colors. To order, call the dealer from whom you purchased your dryer or refer to the “Assistance or

Service” section.

Pedestal Height Color Part Number

10" (25.4 cm) White MHP1000SQ0 10" (25.4 cm) Black MHP1000SB0

15.5" (39.4 cm) White MHP1500SQ0

15.5" (39.4 cm) Black MHP1500SB0

15.5" (39.4 cm) Pacific Blue MHP1500SK0

34.15" (86.74 cm)

Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your dryer. For further information, please refer to the “Assistance or Service” section.

Stack Kit

Are you planning to stack your washer and dryer? To do so, you will need to purchase a Stack Kit. To order, call the dealer from whom you purchased your dryer or refer to the “Assistance or Service” section. Ask for Part Number 8212640.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

■ A location that allows for proper exhaust installation. See “Venting Requirements.”

■ A separate 30-amp circuit.

■ If you are using a power supply cord, a grounded electrical outlet located within 2 ft

(61 cm) of either side of the dryer. See “Electrical Requirements.”

■ A sturdy floor to support the total dryer weight of 127 lbs (57.6 kg). The combined weight

of a companion appliance should also be considered.

■ A level floor with a maximum slope of 1" (2.5 cm) under entire dryer. (If slope is greater

than 1" [2.5 cm], install Extended Dryer Feet Kit, Part No. 279810.) Clothes may not tumble properly and automatic sensor cycles may not operate correctly if dryer is not level.

■ For a garage installation, you will need to place the dryer at least 18" (46 cm) above the

floor. If using a pedestal, you will need 18" (46 cm) to the bottom of the dryer.

Do not operate your dryer at temperatures below 45ºF (7ºC). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

Dryer Dimensions

50"

(128.27 cm)

36"

(91.4 cm)

*28.65"

(72.77 cm)

27"

(68.6 cm)

*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the

exhaust vent with elbow. See “Venting Requirements.”

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons:

■ Additional spacing should be considered for ease of installation and servicing.

■ Additional clearances might be required for wall, door and floor moldings.

■ Additional spacing should be considered on all sides of the dryer to reduce noise transfer.

■ For closet installation, with a door, minimum ventilation openings in the top and bottom

of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

■ Companion appliance spacing should also be considered.

Installation clearances

The location must be large enough to allow the dryer door to open fully.

Installation spacing for custom undercounter installation

Custom undercounter installation - Dryer only

36" min

(91.4 cm)

2"* (5 cm)

Recessed or closet installation - Dryer on pedestal

14" max. (35.6 cm)

18" min.* (45.72 cm)

1"*

(2.5 cm)

27"

(68.6 cm)

(2.5 cm)

*Required spacing

Closet installation - Dryer only

1"*

(2.5 cm)

14" max.* (35.6 cm)

18" min.*

(45.72 cm)

28.65"

(72.77 cm)

"**

(12.7 cm)

48 in.

(310 cm

24 in.

(155 cm

)

A. Side view - closet or confined area B. Closet door with vents

*Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

1"*

28.65"

(72.77 cm)

5"**

(12.7 cm)

3"*

(7.6 cm)

(2.5 cm)

27"

(68.6 cm)

(2.5 cm)

A. Recessed area B. Side view - closet or confined area

*Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

Recommended installation spacing for cabinet installation

■ The dimensions shown are for the minimum spacing allowed.

3"*

(7.6 cm)

■ For cabinet installation, with a door, minimum ventilation openings in the top of the

cabinet are required.

7"* (17.8 cm)

9"* (22.9 cm)

28.65"

(72.77 cm)

1"* (2.5 cm)

(2.5 cm)

27"

(68.6 cm)

1" (2.5 cm)

5"**

(12.7 cm)

*Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

Recommended installation spacing for recessed or closet installation, with stacked washer and dryer

The dimensions shown are for the recommended spacing.

48 in.2 *

(310 cm2)

3"* (7.6 cm)

24 in.

(155 cm2)

1"* (2.5 cm)

*Required spacing

6"* (15.2 cm)

72"

(182.9 cm)

5¹⁄₂"** (14 cm)

(2.5 cm)

27"

(68.6 cm)

(2.5 cm)

*Required spacing

**For venting out the side, 1" (2.5 cm) spacing is allowed.

Mobile home - Additional installation requirements

This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH.

Mobile home installations require:

■ Metal exhaust system hardware, which is available for purchase from your dealer.

■ Special provisions must be made in mobile homes to introduce outside air into the dryer.

The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

Electrical Requirements - U.S.A. Only

It is your responsibility

■ To contact a qualified electrical installer.

■ To be sure that the electrical connection is adequate and in conformance with the

National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and ordinances.

The National Electric Code requires a 4-wire power supply connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269.

■ To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical

supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit.

■ Do not use an extension cord.

■ If codes permit and a separate ground wire is used, it is recommended that a qualified

electrician determine that the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

■ This dryer is manufactured ready to install with a 3-wire electrical supply connection. The

neutral ground conductor is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground conductor must be removed from the external ground connector (green screw), and secured under the neutral terminal (center or white wire) of the terminal block. When the neutral ground conductor is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the neutral conductor.

■ If local codes do not permit the connection of a neutral ground wire to the neutral wire,

see “Optional 3-wire connection” section.

■ A 4-wire power supply connection must be used when the appliance is installed in a

location where grounding through the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductors.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:

■ A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be

type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.

■ A UL listed strain relief.

If your outlet looks like this:

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green or bare. The neutral conductor must be identified by a white cover.

If your outlet looks like this:

GROUNDING INSTRUCTIONS

■

For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

■

For a permanently connected dryer: This dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer.

3-wire receptacle (10-30R)

Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire) and be:

■ Flexible armored cable or nonmetallic sheathed copper cable (with ground wire),

protected with flexible metallic conduit. All current-carrying wires must be insulated.

■ 10-gauge solid copper wire (do not use aluminum).

■ At least 5 ft (1.52 m) long.

WARNING:

Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug on the power supply cord: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Electrical Requirements - Canada Only

WARNING

Electrical Shock Hazard Plug into a grounded 4 prong outlet. Failure to do so can result in death or electrical shock.

It is your responsibility

■ To contact a qualified electrical installer.

■ To be sure that the electrical connection is adequate and in conformance with the

Canadian Electrical Code, C22.1-latest edition and all local codes. A copy of the above codes standard may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

■ To supply the required 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical

supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit.

■ This dryer is equipped with a CSA International Certified Power Cord intended to be

plugged into a standard 14-30R wall receptacle. The cord is 5 ft (1.52 m) in length. Be sure wall receptacle is within reach of dryer’s final location.

If you are using a replacement power supply cord, it is recommended that you use Power Supply Cord Replacement Part Number 9831317. For further information, please reference the service numbers located in the “Assistance or Service” section

GROUNDING INSTRUCTIONS

■

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer is equipped with a cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

■ Do not use an extension cord.

4-wire receptacle 14-30R

Electrical Connection - U.S.A. Only

Power Supply Cord Direct Wire

WARNING

Fire Hazard Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (silver). Ground wire (green or bare wire) must be connected to

green ground connector. Connect remaining 2 supply wires to remaining

2 terminals (gold). Securely tighten all electrical connections. Failure to do so can result in death, fire, or

electrical shock.

1. Disconnect power.

2. Remove the hold-down screw and terminal block cover.

A. Neutral ground wire B. External ground conductor screw C. Center, silver-colored terminal

block screw

D. Terminal block cover and hold-

down screw

WARNING

Fire Hazard Use 10 gauge solid copper wire. Use a UL listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (silver). Ground wire (green or bare wire) must be connected to

green ground connector. Connect remaining 2 supply wires to remaining

2 terminals (gold). Securely tighten all electrical connections. Failure to do so can result in death, fire, or

electrical shock.

3. Install strain relief. Style 1: Power supply cord strain relief

■ Remove the screws from a ³⁄₄" (1.9 cm) UL listed strain relief (UL marking on strain

relief). Put the tabs of the two clamp sections into the hole below the terminal block opening so that one tab is pointing up and the other is pointing down, and hold in place. Tighten strain relief screws enough to hold the two clamp sections together.

A. Strain relief tab pointing up

B C

B. Hole below terminal block opening C. Clamp section

D. Strain relief tab pointing down

■ Put power supply cord through the strain relief. Be sure that the wire insulation on the

power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point.

Style 2: Direct wire strain relief

■ Unscrew the removable conduit connector and any screws from a ³⁄₄" (1.9 cm) UL

listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole below the terminal block opening. Reaching inside the terminal block opening, screw the removable conduit connector onto the strain relief threads.

■ Put direct wire cable through the strain relief. The strain relief should have a tight fit

with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire cable.

4. Now complete installation following instructions for your type of electrical connection: 4-wire (recommended)

3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has: And you will be

Go to Section

connecting to:

4-wire receptacle (NEMA Type 14-30R)

A UL listed, 120/240volt minimum,

4-wire connection:

Power supply cord 30-amp, dryer power supply cord*

A. Removable conduit connector B. Hole below terminal block opening C. Strain relief threads

4-wire direct A fused disconnect or

(12.7 cm)

3-wire receptacle (NEMA type 10-30R)

circuit breaker box*

A UL listed, 120/240volt minimum,

4-wire connection:

Direct Wire

3-wire connection:

Power supply cord 30-amp, dryer power supply cord*

3-wire direct A fused disconnect or

circuit breaker box*

3¹⁄₂"

(8.9 cm)

3-wire connection:

Direct Wire

*If local codes do not permit the connection of a cabinet-ground conductor to the neutral

wire, go to “Optional 3-wire connection” section.

4-wire connection: Power supply cord

3. Connect ground wire (green or bare) of power supply cord to external ground conductor

screw. Tighten screw.

IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections.

A. 4-wire receptacle (NEMA type 14-30R) B. 4-prong plug C. Ground prong

D. Neutral prong

E. Spade terminals with upturned ends F. ¾" (1.9 cm) UL listed strain relief

G. Ring terminals

1. Remove center silver-colored terminal block screw.

2. Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and the neutral wire (white or center wire) of power supply cord under center, silver-colored terminal block screw. Tighten screw.

A. External ground conductor screw B. Ground wire (green or bare) of power supply cord

³⁄₄

" (1.9 cm) UL listed strain relief

D. Center silver-colored terminal block screw

E. Neutral ground wire F. Neutral wire (white or center wire)

4. Connect the other wires to outer terminal block screws. Tighten screws.

A. External ground conductor screw - Dotted line shows position

of NEUTRAL ground wire before being moved to center silver-

colored terminal block screw. B. Center silver-colored terminal block screw C. Neutral ground wire

D. Neutral wire (white or center wire)

E. ¾" (1.9 cm) UL listed strain relief

5. Tighten strain relief screws.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-

down screw.

7. You have completed your electrical connection. Now go to “Venting Requirements.”

4-wire connection: Direct wire

IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do

not permit the use of 3-wire connections. Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.

Strip 5" (12.7 cm) of outer covering from end of cable, leaving bare ground wire at 5"

(12.7 cm). Cut 1¹⁄₂" (3.8 cm) from 3 remaining wires. Strip insulation back 1" (2.5 cm). Shape ends of wires into a hook shape.

(2.5 cm)

3. Connect ground wire (green or bare) of direct wire cable to external ground conductor

screw. Tighten screw.

(12.7 cm)

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown.

1. Remove center silver-colored terminal block screw.

2. Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the terminal block. Squeeze hooked ends together. Tighten screw.

A. External ground conductor screw B. Ground wire (green or bare) of power supply cable C. ¾" (1.9 cm) UL listed strain relief

D. Center silver-colored terminal block screw

E. Neutral ground wire F. Neutral wire (white or center wire)

4. Place the hooked ends of the other direct wire cable wires under the outer terminal block

screws (hooks facing right). Squeeze hooked ends together. Tighten screws.

5. Tighten strain relief screw.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-

down screw.

7. You have completed your electrical connection. Now go to “Venting Requirements.”

A. External ground conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to

center silver-colored terminal block screw. B. Center silver-colored terminal block screw C. Neutral ground wire

D. Neutral wire (white or center wire)

E. ¾" (1.9 cm) UL listed strain relief

3-wire connection: Power supply cord

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

3. Connect the other wires to outer terminal block screws. Tighten screws.

A. 3-wire receptacle (NEMA type 10-30R) B. 3-wire plug C. Neutral prong

D. Spade terminals with up turned ends

³⁄₄

" (1.9 cm) UL listed strain relief

F. Ring terminals

G. Neutral (white or center wire)

1. Loosen or remove center silver-colored terminal block screw.

2. Connect neutral wire (white or center wire) of power supply cord to the center, silver-

colored terminal screw of the terminal block. Tighten screw.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-

down screw.

6. You have completed your electrical connection. Now go to “Venting Requirements.”

3-wire connection: Direct wire

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed. Strip 3¹⁄₂" (8.9 cm) of outer covering from end of cable. Strip insulation back 1" (2.5 cm). If

using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of wires into a hook shape.

(2.5 cm)

3¹⁄₂"

(8.9 cm)

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown.

A. External ground conductor screw B. Neutral ground wire C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

³⁄₄

" (1.9 cm) UL listed strain relief

1. Loosen or remove center silver-colored terminal block screw.

2. Place the hooked end of the neutral wire (white or center wire) of direct wire cable under

the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw.

A. External ground conductor screw B. Neutral ground wire C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

³⁄₄

" (1.9 cm) UL listed strain relief

3. Place the hooked ends of the other direct wire cable wires under the outer terminal block

screws (hooks facing right). Squeeze hooked ends together. Tighten screws.

Optional 3-wire connection

Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.

1. Remove center silver-colored terminal block screw.

2. Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver-colored terminal block screw. Tighten screw.

4. Tighten strain relief screw.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-

down screw.

6. You have completed your electrical connection. Now go to “Venting Requirements.”

A. External ground conductor screw B. Center silver-colored terminal block screw C. Neutral ground wire

D. Neutral wire (white or center wire)

³⁄₄

" (1.9 cm) UL listed strain relief

F. Grounding path determined by a qualified electrician

3. Connect the other wires to outer terminal block screws. Tighten screws.

4. Tighten strain relief screws.

5. Connect a separate copper ground wire from the external ground conductor screw to an

adequate ground.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-

down screw.

Venting Requirements

WARNING

Fire Hazard Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a concealed space of a building.

Rigid metal vent

■ For best drying performance, rigid metal vents are recommended.

■ Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

■ Flexible metal vents are acceptable only if accessible for cleaning.

■ Flexible metal vent must be fully extended and supported when the dryer is in its final

location.

■ Remove excess flexible metal vent to avoid sagging and kinking that may result in

reduced airflow and poor performance.

■ Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45° elbows provide better airflow than 90° elbows.

If using an existing vent system

■ Clean lint from the entire length of the system and make sure exhaust hood is not plugged

with lint.

■ Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

■ Review Vent system chart. Modify existing vent system if necessary to achieve the best

drying performance.

If this is a new vent system

Vent material

■ Use a heavy metal vent. Do not use plastic or metal foil vent.

■ 4" (10.2 cm) heavy metal exhaust vent and clamps must be used.

10.2 cm

4" (10.2 cm) heavy metal exhaust vent

Vent products can be purchased from your dealer or by calling Maytag Services. For more information, see the “Assistance or Service” section.

Good Better

Clamps

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws or other fastening devices

that extend into the interior of the duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

Plan Vent System

(10.2 cm)

4" (10.2 cm)

A. Louvered hood style

B. Box hood style

The angled hood style (shown here) is acceptable.

(10.2 cm)

2½"

(6.4 cm)

■ An exhaust hood should cap the vent to keep rodents and insects from entering the home.

■ Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in

the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

■ Do not use an exhaust hood with a magnetic latch.

Improper venting can cause moisture and lint to collect indoors, which may result in:

Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc.

Housecleaning problems and health problems.

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer. Other installations are possible.

E F G

A. Dryer B. Elbow C. Wall

D. Exhaust hood

E. Clamps

F. Rigid metal or flexible metal vent G. Vent length necessary to connect elbows H. Exhaust outlet

Optional exhaust installations

WARNING

Fire Hazard

Cover unused exhaust holes with one of the following kits:

279818 (white) 279820 (black) 280102 (pacific blue) Contact your local dealer. Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

This dryer can be converted to exhaust out the right side, left side, or through the bottom. Contact your local dealer to have the dryer converted.

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.

A. Standard rear offset exhaust installation B. Left or right side exhaust installation C. Bottom exhaust installation (not an option with

pedestal installations)

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Two closeclearance installations are shown. Refer to the manufacturer’s instructions.

A. Over-the-top installation (also available with one

offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate installations are available for purchase. Please see the “Assistance or Service” section to order.

■ Over-the-Top Installation:

Part Number 4396028

■ Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm) mismatch Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm) mismatch

Determine vent path

■ Select the route that will provide the straightest and most direct path outdoors.

■ Plan the installation to use the fewest number of elbows and turns.

■ When using elbows or making turns, allow as much room as possible.

■ Bend vent gradually to avoid kinking.

■ Use the fewest 90° turns possible.

Determine vent length and elbows needed for best drying performance

■ Use the following Vent system chart to determine type of vent material and hood

combinations acceptable to use. NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust

systems longer than those specified will:

■ Shorten the life of the dryer.

■ Reduce performance, resulting in longer drying times and increased energy usage.

The Vent system chart provides venting requirements that will help to achieve the best drying performance.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90º turn inside the dryer. To determine

maximum exhaust length, add one 90º turn to the chart.

Number of 90º turns or elbows

0 Rigid metal

1 Rigid metal

2 Rigid metal

3 Rigid metal

4 Rigid metal

Type of vent

Flexible metal

Box or louvered hoods

64 ft (20 m) 36 ft (11 m)

54 ft (16.5 m) 31 ft (9.4 m)

44 ft (13.4 m) 27 ft (8.2 m)

35 ft (10.7 m) 25 ft (7.6 m)

27 ft (8.2 m) 23 ft (7 m)

Angled hoods

58 ft (17.7 m) 28 ft (8.5 m)

48 ft (14.6 m) 23 ft (7 m)

38 ft (11.6 m) 19 ft (5.8 m)

29 ft (8.8 m) 17 ft (5.2 m)

21 ft (6.4 m) 15 ft (4.6 m)

2. Firmly grasp the body of the dryer (not the console panel). Gently lay the dryer on the

cardboard. See illustration.

3. Examine the leveling legs. Find the diamond marking.

Install Vent System

1. Install exhaust hood. Use caulking compound to seal exterior wall opening around

exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust

hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible. See “Determine vent path” in

“Plan Vent System.” Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior of the vent to secure vent.

Install Leveling Legs

WARNING

Excessive Weight Hazard Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

1. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place

cardboard under the entire back edge of the dryer.

4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the

diamond marking is no longer visible.

5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners.

Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent.

Connect Vent

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to

existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible gas line.

4. Once the exhaust vent connection is made, remove the corner posts and cardboard.

Level Dryer

Check the levelness of the dryer. Check levelness first side to side, then front to back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.

Reverse Door Swing

You can change your door swing from a right-side opening to a left-side opening, if desired.

1. Place a towel or soft cloth on top of the dryer or work space to protect the surface. Remove the door assembly

1. Remove the 4 screws that hold the door hinge on the front panel of the dryer.

A. Dryer front panel B. Door assembly

2. Lay the door assembly on a flat, protected surface with the inside (inner door assembly)

facing up.

3. Remove the 6 Phillips head screws to release the outer door assembly from the inner door

assembly, as indicated below. See illustration. It is important that you remove only the 6 indicated screws.

5. Rotate outer door 180°.

180˚

Reverse hinge

1. Use a small flat-blade screwdriver to remove 2 plug strips from the inner door. Slide the

head of the screwdriver under the plugs, being certain not to scratch the inner door surface. Lift up.

4. Lift the inner door assembly off the outer door assembly.

2. Remove the 4 screws that attach to the inner door hinge and move the hinge to the other

side. Reinstall the 4 screws.

A. Door hinge

3. Reinstall plug strips on opposite side of the inner door.

4. Check for fingerprints on the glass. Clean glass if necessary.

5. Place the inner door assembly inside the outer door assembly. To fit correctly, the inner

door assembly edge fits completely inside the outer door assembly edge.

6. Reassemble the inner and outer door assemblies with the 6 screws.

3. Insert strike on the opposite side.

A. Plug strip (cannot be seen from this angle) B. Door strike

Reinstall the door

1. Reattach door to dryer front panel with the 4 screws.

Reverse the strike

1. Use a small flat-blade screwdriver to remove plug strip from the dryer door opening. Slide

the head of the screwdriver under the plugs, being certain not to scratch the dryer surface. Lift up.

2. Remove the strike

A. Dryer front panel B. Door assembly

2. Check for fingerprints on the glass. Clean glass if necessary.

3. Close door and check that it latches securely.

Complete Installation

1. Check that all parts are now installed. If there is an extra part, go back through the steps to

see which step was skipped.

2. Check that you have all of your tools.

3. Check the dryer’s final location. Be sure the vent is not crushed or kinked.

4. Check that the dryer is level. See “Level Dryer.”

5. In the U.S.A.

■ For power supply cord installation, plug into a grounded outlet. For direct wire

installation, turn on power.

In Canada

■ Plug into a grounded 4 prong outlet. Turn on power.

6. Remove any protective film or tape remaining on the dryer.

7. Dispose of/recycle all packaging materials.

8. Read “Dryer Use.”

9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

10. Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only

Temperature setting.

If the dryer will not start, check the following:

■ Controls are set in a running or “On” position.

■ Start button has been pushed firmly.

■ Dryer is plugged into an outlet and/or electrical supply is on.

■ Household fuse is intact and tight, or circuit breaker has not tripped.

■ Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If

you feel heat, cancel cycle and close the door.

If you do not feel heat, turn off the dryer and check the following:

■ There may be 2 household fuses or circuit breakers for the dryer. Check that both fuses

are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician.

NOTE: You may notice an odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away.

DRYER USE

Starting Your Dryer

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Do not dry anything that has ever had anything flammable on it (even after washing).

Failure to follow these instructions can result in death, explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

Follow these basic steps to start your dryer. Please refer to specific sections of this manual for more detailed information. This information covers several different models. Your dryer

may vary from the model shown and may not have all the cycles and features described.

WARNING

Fire Hazard No washer can completely remove oil. Do not dry anything that has ever had any type of oil on

it (including cooking oils). Items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle. Failure to follow these instructions can result in death

or fire.

1. Clean lint screen before each load. See “Cleaning the Lint Screen.”

2. Place laundry into dryer and shut door.

3. Press POWER.

4. Select a Sensor Dry or Timed Dry Cycle. The preset settings for Sensor Dry or Timed Dry

Cycles will illuminate. The estimated (Sensor Dry cycle) or actual (Timed Dry) cycle time (in minutes) will show in the display.

NOTE: A default time is displayed when an automatic cycle is selected. During the first few minutes of the drying process, the cycle time may automatically vary from the default time based on the size and fabric type of the load. Toward the end of the drying process, the estimated time display will adjust again, showing the final drying time.

To use a Sensor Dry Cycle

■ Select a Sensor Dry Cycle. Sensor Dry Cycles are preset to Normal.

■ Select DRYNESS LEVEL to adjust how dry you want the load. As the cycle runs, the

control senses the dryness of the load and adjusts the time automatically for the selected dryness level.

To make changes to the Dryness Level and/or Options during a Sensor Dry Cycle:

■ Press PAUSE/CANCEL once.

■ Adjust Dryness Level and/or options.

NOTE: Dryness Level selections can be made only while using Sensor Dry Cycles. Selecting More, Normal or Less automatically adjusts the sensed time needed.

To make changes to Time and/or options during a Timed Dry Cycle:

■ Press PAUSE/CANCEL once.

■ Adjust the Time and/or Options.

5. (OPTIONAL STEP) If desired, select WRINKLE PREVENT. For more details, see “WRINKLE

PREVENT” in the “Additional Features” section.

6. (OPTIONAL STEP) The Cycle Signal is preset to on. If desired, you may turn the Cycle

Signal off.

7. Press and hold START for approximately 1 second until dryer starts. Be sure the door is

closed.

■ If you do not press Start within 5 minutes of selecting a cycle, the dryer automatically

shuts off.

Stopping or Restarting Your Dryer

To pause/stop the dryer at any time

Open the door or press PAUSE/CANCEL once.

To restart the dryer

Close the door. Press and hold START until dryer starts.

To end/cancel your dryer at any time

Press PAUSE/CANCEL twice or open the door. NOTE: Drying will continue from where the cycle was interrupted if you close the door and

press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off. Select new cycle settings before restarting the dryer.

Sensor Dry cycles take the guesswork out of drying time and enhances fabric care. The amount of time that is displayed is the estimated time remaining in the cycle.

To use a Timed Dry Cycle

■ Select a Timed Dry Cycle.

■ Press the Timed Dry Cycle Adjust up or down arrow buttons until the desired drying

time is displayed. Tap the Timed Dry Cycle Adjust up or down arrow buttons and the time will change by 1-minute intervals. Press and hold the Timed Dry Cycle Adjust up or down arrow buttons, and the time will change by 5-minute intervals.

NOTE: The Timed Dry Cycle Adjust feature can be used only with Timed Dry Cycles.

■ Press TEMPERATURE until the desired temperature illuminates.

Lock Controls

This feature allows you to lock your settings to avoid unintended use of the dryer. You can also use the control lock feature to avoid unintended cycle or option changes during dryer operation.

To enable the control lock feature:

Press and hold CYCLE SIGNAL button for 3 seconds. The CONTROLS LOCKED icon lights up, and a single beep tone is heard. To unlock, press and hold CYCLE SIGNAL button for 3 seconds. The indicator light turns off.

Drying and Cycle Tips

Select the correct cycle and dryness level or temperature for your load. If a Sensor Dry Cycle is running, the display shows the estimated cycle time, which is determined by your dryer automatically sensing the dryness level of your load. If a Timed Dry Cycle is running, the display shows the exact number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level.

Drying tips

■ Follow care label directions when they are available.

■ If desired, add a fabric softener sheet. Follow package instructions.

■ To reduce wrinkling, remove the load from the dryer as soon as tumbling stops. This is

especially important for permanent press, knits, and synthetic fabrics.

■ Avoid drying heavy work clothes together with lighter fabrics. This could cause

overdrying of lighter fabrics and lead to increased shrinkage or wrinkling.

Cycle tips

■ Dry most loads using the preset cycle settings.

■ Refer to the Sensor Dry Cycles or Timed Dry Cycles Preset Settings chart (in the “Cycles”

section) for a guide to drying various loads.

■ Drying temperature and Dryness Level are preset when you choose an Sensor Dry

Cycle. You can select a different dryness level, depending on your load, by pressing Dryness Level and choosing More or Less.

NOTE: You cannot use the Timed Dry Cycle Adjust Up or Down arrow buttons and you cannot modify temperature with the Sensor Dry cycles.

■ If you wish to adjust the cycle length of a Timed Dry Cycle, press the Timed Dry Cycle

Adjust up or down arrow buttons. Adjust the temperature of a Timed Dry Cycle by pressing TEMPERATURE until the desired temperature is selected.

NOTE: You cannot use the Dryness Level with Timed Dry Cycles.

Status Lights

Follow the progress of your dryer with the drying Status indicator lights.

Wet

The Wet light illuminates at the beginning of an Auto Cycle if a wet item is detected.

■ In an Sensor Dry Cycle, if a wet item is not detected after approximately 5 minutes, the

dryer goes directly into Cool Down and the Cool Down and WRINKLE PREVENT indicators illuminate, if selected.

■ In a Timed Dry Cycle, wet items are not detected. The dryer will continue to run for the

length of time selected, and the Wet light will illuminate. The damp light will not illuminate.

Damp

The Damp light illuminates in an Sensor Dry Cycle when the laundry is approximately 80% dry.

Cool Down

The Cool Down light illuminates during the cool down part of the cycle. Laundry cools for ease in handling.

Dry

The Dry light illuminates when the drying cycle is finished. This indicator stays on during WRINKLE PREVENT.

WRINKLE PREVENT

The WRINKLE PREVENT light illuminates when this option is selected. This indicator stays on with Dry.

Clean Lint Screen

The Clean Lint Screen light is a reminder to check to see whether the lint screen needs to be cleaned. The Clean Lint Screen light will come on when the machine is turned on. The light will flash until the cycle is started or the door is opened, and then the light will turn off.

Indicator lights

Other indicator lights show Cycle, Options and Modifier settings selected.

Cycles

Select the drying cycle that matches the type of load you are drying. See the Sensor Dry Cycles Preset Settings chart or the Timed Dry Cycles Preset Settings chart.

Sensor Dry Cycles

Sensor Dry Cycles allow you to match the cycle to the load you are drying. See the following Sensor Dry Cycles Preset Settings chart. Each cycle dries certain fabrics at the recommended temperature. A sensor detects the moisture in the load and automatically adjusts the drying time for optimal drying.

Cotton/Towels or Heavy Duty

Use this cycle to get high heat for heavy fabrics such as cotton towels or bedspreads.

Jeans

Use this cycle to get regular heat for drying denims.

Normal

Use this cycle to get medium heat for drying sturdy fabrics such as sturdy work clothes and sheets.

Wrinkle Control

Use this cycle to get low heat for drying no-iron fabrics such as sport shirts, casual business clothes and permanent press blends.

Delicate

Use this cycle to get extra-low heat for drying synthetic fabrics, washable knit fabrics and noiron finishes.

Sensor Dry Cycles Preset Settings

Sensor Dry Cycles Load Type Temperature Time*

(Minutes)

COTTON/TOWELS or HEAVY DUTY

Heavyweight mixed loads, towels

JEANS

Denim pants, jackets

NORMAL

Sheets, corduroys, sturdy work clothes

WRINKLE CONTROL

Permanent press, synthetics, casual business clothes

DELICATE

Lingerie, blouses

*Estimated time with dryness level (normal) setting. Time will vary depending on load type

and load size.

High 45

Regular 55

Medium 40

Low 35

Extra Low 30

Timed Dry Cycles

Use Timed Dry Cycles to select a specific amount of drying time and a drying temperature. When a Timed Dry Cycle is selected, the Estimated Time Remaining display shows the actual time remaining in your cycle. You can change the actual time in the cycle by pressing the Timed Dry Cycle Adjust Up or Down arrow buttons. See “Changing Cycles, Options and Modifiers.”

Timed Dry

Use this cycle to complete drying if items are still damp after an Sensor Dry Cycle. Timed Dry is also useful for drying heavyweight and bulky items such as bedspreads and work clothes.

Rapid Dry

Use this cycle for drying small loads or loads that need a short drying time.

Freshen Up

Use this cycle to help smooth out wrinkles from items such as clothes packed in a suitcase or items wrinkled from being left in the dryer too long.

Timed Dry Cycles Preset Settings

Timed Dry Cycles Load Type Temperature Default Time

(Minutes)

TIMED DRY Heavyweight, bulky items,

bedspreads, work clothes

RAPID DRY

Small loads, sturdy fabric FRESHEN UP

Helps to smooth out wrinkles

High 40

High 23

Regular 20

Additional Features

Tempe ratur e

Temperature settings are used with the Timed Dry Cycles. Press TEMPERATURE until the desired temperature setting illuminates. Temperature settings cannot be used with the Sensor Dry Cycles.

WRINKLE PREVENT

WRINKLE PREVENT helps smooth out wrinkles that form when you cannot unload the dryer promptly at the end of a cycle. During this option, the dryer periodically starts and stops, tumbling the load for 90 minutes.

■ Press WRINKLE PREVENT to get up to 90 minutes of heat-free, periodic tumbling at the

end of a cycle.

■ Stop WRINKLE PREVENT at any time by pressing WRINKLE PREVENT or opening the

dryer door.

■ WRINKLE PREVENT is preset to OFF. The Sensor Dry cycles will retain the WRINKLE

PREVENT setting. For example, if you select WRINKLE PREVENT in the Normal cycle, WRINKLE PREVENT will be on the next time you select the Normal cycle.

NOTE: WRINKLE PREVENT must be selected with a cycle in order to work. If you do not select WRINKLE PREVENT, the dryer stops after cool down.

Cycle Signal

The Cycle Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling.

Press CYCLE SIGNAL to turn the signal off.

Air Fluff

Use the Air Fluff temperature setting for items that require drying without heat such as rubber, plastic and heat-sensitive fabrics. This chart shows examples of items that can be dried using Air Fluff.

Type of Load Time* (Minutes)

Foam rubber - pillows, padded bras, stuffed toys 20 - 30 Plastic - Shower curtains, tablecloths 20 - 30 Rubber-backed rugs 40 - 50 Olefin, polypropylene, sheer nylon 10 - 20

*Reset time to complete drying, if needed.

When using Air Fluff

■ Check that coverings are securely stitched.

■ Shake and fluff pillows by hand periodically during the cycle.

■ Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Air Fluff is not available with Sensor dry cycles.

NOTE: When the WRINKLE PREVENT feature is selected and the Cycle Signal is on, an

audible sound will emit every 5 minutes until the clothes are removed, or the WRINKLE PREVENT feature ends.

Changing Cycles, Options and Modifiers

You can change Sensor Dry Cycles, Timed Dry Cycles, Options, and Modifiers anytime before pressing Start.

■ Three short tones sound if an unavailable combination is selected. The last selection will

not be accepted.

Changing Cycles after pressing Start

1. Press PAUSE/CANCEL twice. This ends the current cycle.

2. Select the desired cycle and options.

3. Press and hold START. The dryer starts at the beginning of the new cycle. NOTE: If you do not press Start within 5 minutes of selecting the cycle, the dryer

automatically shuts off.

Changing Options and Modifiers after pressing Start

You can change an Option or Modifier anytime before the selected feature begins.

1. Press PAUSE/CANCEL once.

2. Select the new feature.

3. Press and hold START to continue the cycle. NOTE: If you happen to press Pause/Cancel twice, the program clears and your dryer shuts

down. Restart the selection process.

Drying Rack Option

Use the drying rack to dry items such as sweaters and pillows without tumbling. The drum turns, but the rack does not move.

If your model does not have a drying rack, you may be able to purchase one for your model. To find out whether your model allows drying rack usage and for information on ordering, please refer to the front page of this manual or contact the dealer from whom you purchased your dryer.

NOTE: The drying rack must be removed for normal tumbling. Do not use Sensor Dry cycles with the drying rack.

To use the dryer rack

Do not remove the lint screen.

1. Open dryer door.

A. Front edge

2. Place dryer rack inside dryer drum, positioning the back wire on the ledge of the inner

dryer back panel. Push down on front edge of dryer rack to secure over the lint screen.

3. Put the wet items on top of the rack. Leave space between the items so air can reach all

the surfaces.

NOTE: Do not allow items to hang over the edge of the rack.

4. Close the door.

5. Press the POWER button.

6. Select a Timed Dry Cycle and temperature (see following chart). Items containing foam,

rubber or plastic must be dried on a clothesline or by using the Air Fluff temperature setting.

7. You may change the cycle time by pressing Timed Dry Cycle Adjust Up or Down arrow

buttons. Reset time as needed to complete drying. Refer to the following table.

8. Press (and hold) START button (about 3 seconds). This chart shows examples of items that can be rack dried and the suggested temperature

setting and drying time. Actual drying time will depend on the amount of moisture items hold.

Rack Dry Setting Temp. Time* Wool Sweaters

Block to shape and lay flat on the rack.

Stuffed toys or pillows

Cotton or polyester fiber filled

Stuffed toys or pillows

Foam rubber filled Sneakers or canvas shoes Timed Dry

Timed Dry Cycles

Cycles

Low 60

Air Fluff (no heat)

*(Minutes) Reset time to complete drying, if needed.

A. Dryer rack front edge

B. Dryer back panel

+ 64 hidden pages