Maytag UXT4030ADB, UXT4030ADW, UXT4036ADW Installation Guide

30" AND 36" (76.2 AND 91.4 CM) RANGE HOOD

UXT4030AD/UXT4036AD

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. FOR RESIDENTIAL USE ONL IMPOR POUR UTILISA

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories or service,

call: 1-800-253-1301 or visit our website at www.whirlpool.com

In Canada, call 1-800-807-6777 or visit our website at www.whirlpool.ca

HOTTE D’ASPIRATION DE 30" ET 36"

(76,2 ET 91,4 CM)

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composer le 1-800-807-6777 ou visiter notre site Web à www.whirlpool.ca

Table of Contents/Table des matières .....................................2

Models/Modèles :

TANT : LIRE ET CONSERVER CES INSTRUCTIONS.

LI317D/W10646402E

TION RÉSIDENTIELLE UNIQUEMENT

TABLE OF CONTENTS TABLE DES MATIÈRES

RANGE HOOD SAFETY .................................................................2

INSTALLATION REQUIREMENTS .................................................4

Tools and Parts .............................................................................4

Location Requirements ................................................................4

Electrical Requirements ...............................................................5

INSTALLATION INSTRUCTIONS ...................................................6

RANGE HOOD USE ........................................................................9

Range Hood Controls ..................................................................9

RANGE HOOD CARE .....................................................................9

Cleaning .......................................................................................9

WIRING DIAGRAM .......................................................................10

ASSISTANCE OR SERVICE .........................................................11

In the U.S.A. ...............................................................................11

In Canada ...................................................................................11

WARRANTY ..................................................................................12

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE ...............................13

EXIGENCES D’INSTALLATION ...................................................15

Outillage et pièces ......................................................................15

Exigences d’emplacement .........................................................15

Spéciﬁcations électriques ..........................................................16

INSTRUCTIONS D’INSTALLATION .............................................17

UTILISATION DE LA HOTTE .......................................................20

Commandes de la hotte de cuisinière .......................................20

ENTRETIEN DE LA HOTTE .........................................................20

Nettoyage ...................................................................................20

SCHÉMA DE CÂBLAGE ...............................................................21

ASSISTANCE OU SERVICE .........................................................22

Au Canada ..................................................................................22

GARANTIE .....................................................................................23

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer. WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

(2.5 cm)

(12.5 cm)

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

Pencil

#2 Phillips screwdriver

Drill with ¹⁄₈" (3 mm), ¹⁄₂" (13 mm), and 1¹⁄₄" (3 cm) bits

Parts supplied

Remove parts from package. Check that all parts are included.

#8-18 x 1" (4.2 x 25 mm) flat-head screws

Drywall anchors

Parts needed

UL Listed/CSA Approved wire connectors

UL Listed/CSA Approved ¹⁄₂" (13 mm) strain relief

Optional accessories

Charcoal filter kit Part Number W10355450*

* For information on ordering, see the “Assistance or Service”

section.

Power cord kit Part Number W10355452*

Wire stripper

Flat-blade screwdriver

#8-18 x ⁵⁄₈" (4.2 x 16 mm) truss-head screws

Mounting brackets

120V, 75W maximum, type E26 incandescent lamp

Stainless steel cleaner and polish Part Number 31462A*

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■ It is the installer’s responsibility to comply with installation

clearances speciﬁed on the model/serial/rating plate. The model/serial/rating plate is located inside the range hood on the left wall.

■ Range hood location should be away from strong draft

areas, such as windows, doors and strong heating vents.

■ Cabinet opening dimensions that are shown must be

used. Given dimensions provide minimum clearance. Consult the cooktop/range manufacturer installation instructions before making any cutouts.

■ This range hood is recommended for use with cooktops

with a maximum total rating of 40,000 BTUs or less.

■ Grounded electrical outlet is required. See “Electrical

Requirements” section.

■ All openings in ceiling and wall where range hood will

be installed must be sealed.

■ These range hoods are factory set for non-vented

installations and require charcoal ﬁlters. See the “Assistance or Service” section for information on ordering charcoal ﬁlters.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

Product Dimensions

6⁹⁄₁₆" (16.7 cm) or

4¹⁵⁄₁₆"

(5.1 cm)

(2.2 cm)

⁷⁄₈"

9⁹⁄₁₆" (24.4 cm)

29¹⁵⁄₁₆" (76.0 cm) or 35¹⁵⁄₁₆" (91.0 cm)

(22.9 cm)

1¹⁄₂"

(3.8 cm)

18⁵⁄₈"

(47.3 cm)

Installation Clearances

A. 24" (61 cm) minimum distance from electric cooking surface

24" (61 cm) minimum distance from gas cooking surface

30" (76.2 cm) suggested maximum above the cooking surface B. 18" (45.7 cm) minimum clearance - upper cabinet to countertop C. 30" (76.2 cm) minimum cabinet opening width for 30"

(76.2 cm) models and 36" (91.4 cm) minimum cabinet

width for 36" (91.4 cm) models D. 12" (30.5 cm) cabinet depth E. 36" (91.4 cm) base cabinet height

Electrical Requirements

Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest edition) or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition), and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp, fused

electrical circuit is required.

■ If the house has aluminum wiring, follow

the procedure below:

1. Connect a section of solid copper wire

to the pigtail leads.

2. Connect the aluminum wiring to the added section

of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer’s recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating

of the appliance as speciﬁed on the model/serial/rating plate. The model/serial/rating plate is located inside the range hood on the left wall.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition) or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition), and all local codes and ordinances.

Venting Requirements

These range hoods are factory set for non-vented (recirculating) installations and come with a charcoal ﬁlter. See the “Assistance or Service” section for information on ordering a charcoal ﬁlter kit, Part Number W10355450.

INSTALLATION INSTRUCTIONS

1. Disconnect Power

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

2. Mark Hole Locations

3. Install Brackets

■ Using a #2 Phillips screwdriver, install the drywall anchors.

■ Using #8-18 x 1" (4.2 x 25 mm) ﬂat-head #2 Phillips screws,

install the mounting brackets using the upper holes.

NOTE: For installations to a surface other than drywall, it is recommended that a qualiﬁed contractor determine the anchoring method.

4. Prepare Range Hood

Align the exterior edge of the mounting brackets with the exterior edges of the upper cabinet.

IMPORTANT: The brackets should touch the upper cabinet. With a pencil, mark the upper holes on the brackets.

■ Set the range hood on its back on a covered surface.

■ Using a #2 Phillips screwdriver, remove the electrical

box cover.

■ Using a ﬂat-blade screwdriver, remove the appropriate

power supply knockout.

5. Mark Hole Locations

Lift the range hood into place and insert the mounting bracket tabs through the slots in the back of the range hood.

6. Drill Electrical Opening

Using a 11/4" (3 cm) drill bit, drill the hole in the dot marked previously at the electrical strain relief.

OPTIONAL: Using a 1/8" (3 mm) drill bit, drill pilot holes for the dots marked previously at each mounting tab at an approximate 45° angle in an upward direction.

90˚

Hold the range hood ﬁrmly in place with one hand and bend each mounting tab (A) upward approximately 90°.

Mark the hole at the power supply knockout (B). OPTIONAL: Mark the hole in each mounting tab. Remove the range hood and set it aside.

7. Prepare Range Hood Vents

and Mounting Tabs

■ Install Strain Relief

Install a UL Listed/CSA Approved 1/2" (13 mm) strain relief (A).

■ Mounting Tabs

Start a #8-18 x 5/8" (4.2 x 16 mm) truss-head screw into the mounting tab (D) on each side of the range hood as shown in the inset. Insert the screws approximately 2 turns into the mounting tab holes.

■ Non-vent (Recirculating) Installations

Remove the (2) T10 Torx®† screws and remove the top, front rectangular vent cover (B).

†®TORX is a registered trademark of Acument Intellectual Properties, LLC.

8. Mount Range Hood

■ Lift the range hood into place, positioning the rear slots

over the mounting brackets.

■ Using a Phillips screwdriver, push on the screws that

are started into the top mounting tabs and bend the tabs against the cabinet side walls. Attach the screws to the cabinet side walls.

IMPORTANT: Do not overtighten the screws.

■ For direct wire installations, run the home power supply

cable according to the National Electric Code or CSA standards and local codes and ordinances. There must be enough wiring from the fused disconnect (or circuit breaker) box to make the connection in the range hood electrical terminal box.

■ Tighten the strain relief screws.

NOTE: Do not reconnect power until the installation is complete.

OPTIONAL: If you prefer, bend the rear tabs against the rear of the range hood and attach to the wall using #8-18 x 5/8" (4.2 x 16 mm) truss-head screws.

9. Make Electrical Connection

Option 1 - Direct Wire Installations

■ Use a UL Listed/CSA Approved wire connector

and connect the 3 white wires (A) together.

■ Use a UL Listed/CSA Approved wire connector

and connect the 2 black wires (B) together.

WARNING

Fire Hazard Electrically ground the blower. Use copper wire. Connect ground wire to green ground screw in

terminal box. Failure to do so can result in death, fire, or

electrical shock.

■ Connect the green (or bare) ground wire (C) from the

power supply to the green ground screw in the electrical box and tighten the screw securely.

Reinstall the electrical box cover. Reconnect power.

Option 2 - Power Cord Kit Installations

For optional power cord kit installations, follow the instructions supplied with the power cord kit. See the “Assistance or Service” section for information on ordering.

NOTE: Use only with range hood cord connection kits that have been investigated and found acceptable for use with this model range hood.

10. Complete the Installation

■ Install a 120V, 75W maximum, light bulb with

E26 base. See “Replacing the Light Bulb” in the “Range Hood Care” section.

■ If removed previously, replace the ﬁlter. See “Charcoal

Grease Filter” in the “Range Hood Care” section.

■ Check the operation of the range hood fan and light.

See the “Range Hood Use” section. If the range hood does not operate, check to see whether

a circuit breaker has tripped or a household fuse has blown. Disconnect the power and check the wiring connections.

NOTE: To get the most efﬁcient use from your new range hood, read the “Range Hood Use” section.

+ 16 hidden pages