Maytag MTF2142MES00, MTF2142MEW00, MTF2142MEQ00, MTF2142MEB00, MTF1842MEW00 Owner’s Manual

M_ YI AG ®

REFRIGERATOR USE & CARE GUIDE

MANUAL DE USO Y CUIDADO DEL

REFRIGERADOR

GUIDE D'UTILISATION ET D'ENTRETIEN DU

p p

REFRIGERATEUR

Table of Contents / Indice / Table des mati_res

ASSISTANCE OR SERVICE ............................ 1

REFRIGERATOR SAFETY ............................... 2

INSTALLATION INSTRUCTIONS ................... 3

REFRIGERATOR USE ..................................... 9

REFRIGERATOR CARE ................................. 10

TROUBLESHOOTING .................................... 11

WARRANTY .................................................... 13

If you need assistance or service, first see the "Troubleshooting"
section. Additional help is available. Call us at 1-800-688-9900

from anywhere in the U.S.A., or write:

Maytag Services, LLC

ATTN: CAIR ®Center

P.O. Box 2370

Cleveland, TN 37320-2370

Information may also be obtained by visiting our website at

www.maytag.com.

In Canada, for assistance, installation or service, call us at
1-800-807-6777, or write:

Whirlpool Canada LP

Customer Interaction Centre

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

In Canada, visit www.maytag.ca.

Please include a daytime phone number in your correspondence.
Keep this hook and your sales slip together for future

reference. You must provide proof of purchase or installation
date for in-warranty service.

AYUDA O SERVIClO TECNICO .................... 14

SEGURIDAD DEL REFRIGERADOR ............ 14

INSTRUCCIONES DE INSTALACION .......... 15

USO DE SU REFRIGERADOR ...................... 22

CUIDADO DE SU REFRIGERADOR ............. 23

SOLUCION DE PROBLEMAS ....................... 24

GARANTIA ...................................................... 26

Assistance or Service

ASSISTANCE OU SERVICE .......................... 27

SleCURITle DU RleFRIGleRATEUR ................ 27

INSTRUCTIONS D'INSTALLATION .............. 28

UTILISATION DU RleFRIGleRATEUR ........... 35

ENTRETIEN DU RleFRIGleRATEUR ............. 37

DlePANNAGE .................................................. 38

GARANTIE ...................................................... 40

Write down the following information about your appliance to help
you obtain assistance or service if you ever need it. You will need

to know your complete model number and serial number. You can
find this information on the model and serial number label, located
on the inside wall of the refrigerator compartment.

Dealer name

Serial number

Address

Phone number
Model number

Purchase date

Toorder stainless steel cleaner, call 1-800-688-9900 and ask for
the part number listed below or contact your authorized MAYTAG°

appliance dealer. In Canada, call 1-800-807-6777.
Stainless Steel Cleaner & Polish:

Order Part #4396095
In Canada, Order Part #31462B

2320376A

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow
instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the refrigerator, follow basic precautions,

including the following:

m Plug into a grounded 3 prong outlet.
m Do not remove ground prong.

m Do not use an adapter.
m Do not use an extension cord.

m Disconnect power before servicing.
m Replace all parts and panels before operating.
m Remove doors from your old refrigerator.

SAVETHESEJNSTRUCTmONS

m Use nonflammable cleaner.
m Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

m Use two or more people to move and install refrigerator.
m Disconnect power before installing ice maker (on ice maker

kit ready models only).

Proper Disposal of Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of
your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily
climb inside.

INSTALLATION INSTRUCTIONS

i_iii_i_iii?_;!!_:_:_iiii<t !i:!ii_ili!!_i_iiii:_i!'Jii!__;iil;i:!!::;i_ii!_i_i_i_:_;_i:o_ii:¸

Excessive Weight Hazard

Use two or more people to move and install
refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Do not use sharp instruments, rubbing alcohol, flammable fluids,
or abrasive cleaners to remove tape or glue. These products can
damage the surface of your refrigerator. For more information, see
"Refrigerator Safety."

IMPORTANT: Do not remove the white foam air return insert from
behind the control panel on the ceiling of the refrigerator. If the

insert is removed, ice may migrate down from the freezer and
cause icicles to form.

When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.
Always pu!I the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move
it, as floor damage could occur.

Explosion Hazard

Keep flammable materials and vapors, such as
gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

Toensure proper ventilation for your refrigerator, allow for a V2"
(1.25 cm) space on each side and at the top. When installing your

refrigerator next to afixed wall, leave 2" (5.08 cm) minimum on the
hinge side (some models require more) to allow for the door to
swing open. If your refrigerator has an ice maker, allow extra
space at the back for the water line connections.

NOTE: It is recommended that you do not install the refrigerator
near an oven, radiator, or other heat source. Do not install the

refrigerator in a location where the temperature will fall below
55°F (13°C).

Clean Before Using

After you remove all of the package materials, clean the inside of
your refrigerator before using it. See the cleaning instructions in
"Refrigerator Care."

_mportant information to know about glass shelves

and covers:

Do not clean gtass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter
into many smalI, pebble-size pieces= This is normal. Glass

shelves and covers are heavy= Use special care when
removing them to avoid impact from dropping=

II

_/2" {1.25cm)

II

/

2" (5.08 era)

Emectrica_ Shock Hazard

Pmuginto a grounded 3 prong outleto
Do not remove ground prong,

Do not use an adapter,
Do not use an extension cord.

FaiJure to follow these }nstructions can resumt }n death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an

extension cord.
NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or
Freezer Control depending on the model) to OFF and then
disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source and
reset the control (Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired setting.

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • 1/411Drill bit

• 7/1611and 1/211Open-end or two • Hand drill or electric drill
adjustable wrenches (properly grounded)

• 1/411nut driver

NOTE: Your refrigerator dealer has a kit available with a %"
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or 3/lO"

(4.76 mm) saddle valve which reduces water flow and clogs more
easily.

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain
above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and
120 psi (207 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water
pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and
827 kPa).

If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill
after heavy usage.

If you have questions about your water pressure, call a licensed,
qualified plumber.

Read all directions before you begin.
IMPORTANT: Ifyou turn the refrigerator on before the water line is

connected, turn the ice maker OFR

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a 1/2"to 11/4'' (1.25 cm to 3.18 cm) vertical cold water
pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.

4.

Determine the length of copper tubing you need. Measure
from the connection on the lower left rear of refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"
(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both
ends of copper tubing are cut square.

5.

Using a grounded drill, drill a 1/4"hole in the cold water pipe
you have selected.

....... A

G ..................B

............ C

A. Cold waterpipe
B. Pipe clamp
C. Copper tubing
D. Compression nut

6.

Fasten the shutoff valve to the cold water pipe with the pipe

E. Compression sleeve
F. Shutoff valve

G. Packing nut

clamp. Be sure the outlet end is solidly in the 1/4"drilled hole in
the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws slowly
and evenly so washer makes a watertight seal. Do not

overtighten or you may crush the copper tubing.

7. Slipthecompressionsleeveandcompressionnutonthe
coppertubingasshown.Inserttheendofthetubingintothe

outletendsquarelyasfarasitwillgo.Screwcompressionnut
ontooutletend with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn
ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe. Coil the copper
tubing.

Connect to Refrigerator

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do not
overtighten.

3. Use the tube clamp on the back of the refrigerator to secure
the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back
against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.

A. Tube clamp

B. Copper tubing

6. The ice maker is equipped with a built-in water strainer. If your
water conditions require a second water strainer, install it in

the 1/4"(6.35 mm) water line at either tube connection. Obtain
a water strainer from your nearest appliance dealer.

Complete the Installation

C. Compression nut
D. Valve inlet

TOOLS NEEDED: %6" hex-head socket wrench, #2 Phillips
screwdriver, flat-blade screwdriver, %6" open-end wrench, flat 2"
putty knife.

IMPORTANT:

• Unplug refrigerator or disconnect power.

• Remove food and any adjustable door or utility bins from
doors.

• If you only want to remove and replace the doors, see
"Remove Doors and Hinges" and "Replace Doors and
Hinges."

• Depending on your model, you have either standard doors or
contour doors. If you are going to reverse the door swing,

follow the instructions for the appropriate door style.

• All graphics referenced in the following instructions are
included later in this section after "Final Steps."

Remove Doors and Hinges

5/16"Hex-head hinge screw

1. Unplug refrigerator or disconnect power.

2. Open refrigerator door and remove base grille from the bottom
front of the refrigerator. See Base Grille graphic.

3. Close the refrigerator door and keep both doors closed until
you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.

4. Remove the parts for the top hinge as shown in Top Hinge
graphic. Lift the freezer door free from the cabinet.

5. Remove the parts for the center hinge as shown in the Center
Hinge graphic. Lift the refrigerator door free from the cabinet.

6. Remove the parts for the bottom hinge as shown in the
Bottom Hinge graphic.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.
Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.
NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely
fill ice container.

Reverse Doors (optional)

IMPORTANT: If you want to reverse your doors so that they open
in the opposite direction, follow these steps. Ifyou are not

reversing the doors, see "Replace Doors and Hinges."

Standard Doors

Door Stop Screw

Door Handle Sealing Screw

Fiat-Head Handle Screw

Door Handle Seal Screw Front

DoorHinge Hole Plug

Cabinet Hinge Hole Plug

Round-Head Handle Screw

Shoulder Handle Screw

Cabinet

1. Remove 5/16"hex-head hinge screws from handle side and

move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from cabinet top and move
them to opposite side hinge holes as shown in Graphic 1-2.

Freezer Door

1. Remove freezer handle assembly as shown. Keep all parts

together. See Graphic 2.

2. Remove door stop. Move to opposite side of freezer door as
shown in Graphic 5.

3. Position freezer handle on opposite side of freezer door.
Assemble handles on door as shown in Graphic 2.

4. Tighten all screws. Set aside door until hinges and refrigerator
compartment door are in place.

Refrigerator Door

1. Remove refrigerator handle bottom trim. For Style 1, remove
screw from bottom of door and slide trim down as shown in

Graphic 6-1. For Style 2, slide trim down as shown in
Graphic 6-2.

2. Remove refrigerator handle assembly as shown. Keep all
parts together. See Graphic 6-3.

3. Remove door hinge hole plug from refrigerator door. Move to
opposite side hinge hole as shown in Graphic 3.

4. Remove door handle sealing screws. Move to opposite side of
refrigerator door as shown in Graphic 4.

5. Remove door handle seal screw front. Move to opposite side
of refrigerator door as shown in Graphic 7.

6. Remove door stop. Move to opposite side of refrigerator door
as shown in Graphic 5.

7. Position refrigerator handle on opposite side of the refrigerator
door as shown in Graphic 6-3. Drive top two screws in handle
first. Align lower portion of handle and drive bottom screw.

8. Align refrigerator handle bottom trim. For Style 1, slide trim
into place and attach bottom screw. See Graphic 6-1. For

Style 2, slide trim into place. See Graphic 6-2.

9. Tighten all screws. Set aside refrigerator door until bottom
hinge is installed on product.

Contour Doors

Replace Doors and Hinges

NOTE: Graphic may be reversed if door swing is reversed.

1. Replace the parts for the bottom hinge as shown. Tighten
screws. See Bottom Hinge graphic. Replace the refrigerator

door.
NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.

2. Assemble the parts for the center hinge as shown and tighten
all screws. See Center Hinge graphic. Replace the freezer

door.

3. Assemble the parts for the top hinge as shown in Top Hinge
graphic. Do not tighten screws completely.

4. Line up the doors so that the bottom of the freezer door aligns
evenly with the top of the refrigerator door. Tighten all screws.

i

Final Steps

1. Check all holes to make sure that hole plugs and screws are in
place. Reinstall top hinge cover. See Top Hinge graphic.

2. Replace the base grille. See Base Grille graphic.

ElectricaB Shock Hazard

Pmuginto a grounded 3 prong outlet.

Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can resumt in death,
fire, or eiectricam shock.

Round-Hend DoorHandle

HandleScrew Screw Hole Plug

Cabinet

1. Remove 5/16"hex-head hinge screws from handle side and

move them to opposite side. See Graphic 1.

2. Remove cabinet hinge hole plugs from the cabinet top and
move them to opposite side hinge holes as shown in

Graphic 2.

Doors

1. Remove the door hinge hole plug from top of refrigerator door.
Move it to the opposite side as shown in Graphic 3.

2. Remove door stop from both the freezer and refrigerator
doors and move to the other side. See Graphics 4 and 5.

3. Plug into a grounded 3 prong outlet.

4. Return all removable door parts to doors and food to
refrigerator.

Standard Doors

Base Grille

A. Top Hinge Cover

B._" Hex-Head Hinge Screws
C. Top Hinge

............................Center Hinge

iiiiiiiiiiiiii......

!!!!!!!!!!!!!! A

I °°'D\I

A. Door Hinge Hole Plug

A. Flat-Head Handle Screws
B. Freezer Door Handle

A. Door Handle Sealing Screws

Front View Side View

A. Cabinet Hinge Hole Plugs

A. _6" Hex-Head Hinge Screws

/

0

l

I

/

/

I

!

A. Center Hinge

B.5/_,,Hex-Head Hinge Screws

Bottom Hinge

A. Bottom Hinge
B. 5/_,,Hex-Head Hinge Screws

-p

A. Door Stop Screw A B
B. Door Stop

A. Door Handle

Seal Screw Front

B

A. Flat-Head

Handle Screw

A. Shoulder

Handle Screw

B. Round-Head

Handle Screw

Contour Doors

Base Grille

iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii

o.°'°, )

L"

|"," .....................................................................A

A. 5/_8"Hex-Head Hinge Screws

oO

Top Hinge

A. Top Hinge Cover
B. %_"Hex-Head Hinge Screws

C. Top Hinge

Center Hinge

A. Center Hinge
B. 6/_,,Hex-Head Hinge Screws

Bottom Hinge

A. Cabinet Hinge Hole Plugs

B

[]

A. Door Stop
B. Door Stop Screw

Reinstallation of Door Stops

A. Bottom Hinge
B. %_"Hex-Head Hinge Screws

©

A. Door Stop
B. Door Stop Screw

Door Closing

ii_,,_i_ii_!_!i!,i_ii_I!:ii!__ii!!_!_!!iii_o _'i_i__i_i:_!!i_i_;_

REFRIGERATOR USE

Your refrigerator has two front adjustable rollers - one on the right
and one on the left. If your refrigerator seems unsteady or you

want the doors to close easier, adjust the refrigerator's tilt using
the instructions below.

1. Remove the base grille. See the Base Grille graphic in
"Refrigerator Doors." The two leveling screws are part of the

front roller assemblies which are at the base of the refrigerator
on either side.

2. Use a screwdriver to adjust the leveling screws. Turn the
leveling screw to the right to raise that side of the refrigerator

or turn the leveling screw to the left to lower that side. It may
take several turns of the leveling screws to adjust the tilt of the
refrigerator.

NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws and

rollers. This makes it easier to adjust the screws.

3. Open both doors again and check to make sure that they
close as easily as you like. If not, tilt the refrigerator slightly

more to the rear by turning both leveling screws to the right. It
may take several more turns, and you should turn both
leveling screws the same amount.

4. Replace the base grille.

Align Doors

If the space between your doors looks uneven, you can adjust it
using the instructions below:

1. Pry off the top hinge cover.

2. Loosen the top hinge screws using a %6" socket or wrench.

3. Have someone hold the door in place or put a spacer between
the doors while you tighten the top hinge screws.

4. Replace the top hinge cover.

For your convenience, your refrigerator controls are preset at the
factory. When you first install your refrigerator, make sure that the
controls are still preset to the mid-settings as shown.

NOTE: To turn your refrigerator off, turn the refrigerator control to
the word OFF or until the word OFF appears. Your product will not

cool when the refrigerator control is set to OFR

Mid-setting "3"

OFF

5 1

COL_ES @

3

IMPORTANT:

• Give your refrigerator time to cool down completely before
adding food. It is best to wait 24 hours before you put food

into the refrigerator.

• If you add food before the refrigerator has cooled completely,
your food may spoil. Adjusting the Refrigerator and Freezer

Controls to a higher (colder) than recommended setting will
not cool the compartments any faster.

Adjusting Controls

The mid-settings indicated in the previous section should be
correct for normal household usage. The controls are set correctly
when milk or juice is as cold as you like and when ice cream is
firm.

If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not blocked.

If you need to adjust temperatures, use the settings listed in the
chart below as a guide. On models with two controls, adjust the
refrigerator temperature first. Wait at least 24 hours between
adjustments and then recheck the temperatures.

CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR too warm REFRIGERATOR or

TEMPERATURE Control one

setting higher

FREEZER too warm/too FREEZER or TEMPERATURE
little ice Control one setting higher

MAX ice production switch

REFRIGERATOR too cold REFRIGERATOR or

TEMPERATURE Control one

setting lower

FREEZER too cold FREEZER or TEMPERATURE

Control one setting lower

C _i_i_:iis:!/>_ii:!!_i:}ii!!!__i_:_ii!i_i;id iit},¸¸_¸C _:>_iii__!:_ii_iii_!ii

_{}_'_ ao_ _ _o_@_

You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) for best storage of fruits and vegetables with skins.
HIGH (closed) for best storage of fresh, leafy vegetables.

Style 1

To Turn the Ice Maker On/Off:

Toturn the ice maker ON, simply lower the wire shutoff arm.
To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.
NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will
raise the wire shutoff arm to the OFF (arm up) position. Do not
force the wire shutoff arm up or down.

Ice Production Rate:

• The ice maker should produce approximately 8to 12 batches
of ice in a 24-hour period with the ice level adjustment arm in
the factory set 100% position.

NOTE: Adjust the ice level by slightly pressing in on the ice
level adjustment arm to release it from the wire shutoff arm

and then moving it up or down to the desired setting.

• To decrease the amount of ice produced, move the ice level
adjustment arm to the 75% or 50% position.

• For maximum ice production move the ice level adjustment
arm to the 100% position.

Remember

• Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.

• The quality of your ice will be only as good as the quality of the
water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals
(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If asoftened water supply cannot be avoided,
make sure the water softener is operating properly and is well

maintained.

• Do not use anything sharp to break up the ice in the bin. This
can cause damage to the ice container and the dispenser

mechanism.

• Do not store anything on top of or in the ice maker or ice bin.

Ice Production Rate:

• The ice maker should produce approximately 8 to 12 batches
of ice in a 24-hour period.

• To increase ice production, lower the freezer and refrigerator
temperature. See "Using the Controls." Wait 24 hours
between adjustments.

• For maximum ice production (on some models), push the
switch to ICE PLUS. The ice maker should produce 16to
20 batches of ice in a 24-hour period in the Ice Plus mode.

Style 2

To Turn the Ice Maker On/Off:

Toturn the ice maker ON, simply lower the wire shutoff arm.
To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.
NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will
raise the wire shutoff arm to the OFF (arm up) position. Do not
force the wire shutoff arm up or down.

A. Wire shutoff arm
B. Ice level adjustment arm

REFRIGERATOR CARE

Exp}osion Hazard

Use nonflammable c_eaner.
Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid build-
up of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor
transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,
concentrated detergents, bleaches or cleansers containing
petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh
cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

10

3.

Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water.

4.

There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to
3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Removethe base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

5.

Plug in refrigerator or reconnect power.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.

_ICiiiii:__!i__i_i_i:_ii!!ii!_iilliiii_i_i!i_,iti:_i_;__!i!_¸¸i_i;i!;!!i;!!_i_iii:ii!!ii,u! !!:>i!!i_

NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the
bulb with an appliance bulb of the same size, shape, and wattage.

1. Unplug refrigerator or disconnect power.

2. Remove the bulb from behind the control panel in the
refrigerator or from behind the light shield in the freezer (on
some models). Replace it with an appliance bulb of the same
wattage.

3. Plug in refrigerator or reconnect power.

The refrigerator will not operate

E(ectrica} Shock Hazard

Pmuginto a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.
FaiJure to follow these instructions can resumt in death,

fire, or emectdcal shock.

• Power cord unplugged? Plug into a grounded 3 prong outlet.

• Is outlet working? Plug in a lamp to see if the outlet is
working.

• Household fuse blown or circuit breaker tripped? Replace
the fuse or reset the circuit breaker. If the problem continues,

call an electrician.
Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls."
New installation? Allow 24 hours following installation for the

refrigerator to cool completely.
NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its
high-efficiency compressor and fans. The unit may run even
longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to this
reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below are
listed some normal sounds with explanations.

• Buzzing - heard when the water valve opens to fill the ice
maker.

• Pulsating - fans/compressor adjusting to optimize
performance.

• Hissing/Rattling - flow of refrigerant, movement of water
lines, or from items placed on top of the refrigerator.

• Sizzling/Gurgling - water dripping on the heater during
defrost cycle.

• Popping - contraction/expansion of inside walls, especially
during initial cool-down.

• Water running - may be heard when water melts during the
defrost cycle and runs into the drain pan.

• Creaking/Cracking - occurs as ice is being ejected from the
ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct
position.

• Crisper cover in the way? Make sure the crisper cover is
pushed in fully, so that the back rests on the supports.

11

The doors are difficult to open

E×plosion Hazard

Use nonflammable cleaner.
Failure to do so can result in death, e×p_osion, or five°

• Gaskets dirty or sticky? Clean gaskets and contact surfaces
with mild soap and warm water. Rinse and dry with soft cloth.

The lights do not work

• Is a light bulb loose in the socket or burned out? See
"Changing the Light Bulbs."

_iiii(,ii!__iii_:_i_i!i?¸¸¸_i:i!_i_i_:_i_!il__i_iliii_i?_ii!i:ii:__i::!iiii!i_,iliii_::i,iii:_!i_;__:_i_!_i:x::_i:!_

Temperature is too warm

• New installation? Allow 24 hours following installation for the
refrigerator to cool completely.

• Door(s} opened often or left open? Allows warm air to enter
refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for
refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions?
Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s} opened often or left open? Allows humid air to enter
refrigerator. Minimize door openings and keep doors fully

closed.

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch
(depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice

production.

• Large amount of ice recently removed? Allow 24 hours for
ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm?
Remove ice from the ejector arm with a plastic utensil.

• Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff
valve fully open.

• Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.

• Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a
licensed, qualified plumber.

Off-taste, odor or gray color in the ice

• New plumbing connections? New plumbing connections
can cause discolored or off-flavored ice.

• Ice stored too long? Discard ice. Wash ice bin. Allow
24 hours for ice maker to make new ice.

• Odor transfer from food? Use airtight, moisture proof
packaging to store food.

• Are there minerals (such as sulfur) in the water? A water
filter may need to be installed to remove the minerals.

12