Maytag MSD2578VEW00, MSD2578VEM01, MSD2578VEM00, MSD2578VEB00, MSD2578VEA00 Owner’s Manual

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING, please visit our website at www.maytag.com for additional information. If you still need assistance, call us at 1-800-688-9900. In Canada, visit our website at www.maytag.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall ofthe refrigerator compartment.

Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espa_ol, o para obtener informaci6n adicional acerca de su producto, visite: www.maytag.com.

Necesitara su nOmero de modelo y de serie, ubicado en el interior del compartimiento del refrigerador.

Table of Contents / Table des mati res

REFRIGERATOR SAFETY ............................................................ 1

INSTALLATION INSTRUCTIONS ................................................. 2

REFRIGERATOR USE ................................................................... 5

REFRIGERATOR CARE ................................................................ 9

TROUBLESHOOTING ................................................................. 10

ACCESSORIES ............................................................................ 12

WATER FILTER CERTIFICATIONS ........................................... 13

PERFORMANCE DATA SHEETS ............................................... 14

WAR RANTY ................................................................................. 18

SleCURITle DU RleFRIGleRATEUR ............................................. 19

INSTRUCTIONS D'INSTALLATION ........................................... 20

UTILISATION DU RleFRIGleRATEUR ........................................ 23

ENTRETIEN DU RleFRIGleRATEUR .......................................... 28

DlePANNAGE ............................................................................... 29

ACCESSOIRES ............................................................................ 31

FEUlLLES DE DONNI_ES SUR LA PERFORMANCE ............... 32

GARANTIE ................................................................................... 36

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages willtell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

W10216897A

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoff the doors.

• Leave the shelves in place so that children may not easily climb inside.

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

Remove packaging materials. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see "Refrigerator Safety."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for V2"(1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on each side (depending on your model) to allow for the door to swing open. If your refrigerator has an ice maker, allow extra space at the back for the water line connections.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection. Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting. See "Using the

Controls."

NOTES:

It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source. Do not install in a location where the temperature will fall below 55°F (13°C).

Normal minimum cabinet cut-out width required for product installation is 36" (91.44 cm). However, if the product is placed against an extended wall and the ability to remove the crisper pans is desired, an additional 18" (45.72 cm) of cabinet width is required, so a total cabinet opening width of 54" (137.16 cm) is recommended.

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • V4"Nut driver

• 7/le"and V2"Open-end or two • V4"Drill bit adjustable wrenches

NOTE: Your refrigerator dealer has a kit available with a V4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or ¾e"

(4.76 mm) saddle valve which reduces water flow and clogs more easily. IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain

above freezing.

• Cordless drill

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and

827 kPa). If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

• If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration System."

If you have questions about your water pressure, call a licensed, qualified plumber.

Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFR

screws slowly and evenly so the washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw the compression nut onto outlet end with adjustable wrench. Do not

overtighten.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do

not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

B C

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2"(12.70 mm) to 1V4" (3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use V4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a V4"(6.35 mm) hole in the cold water pipe you have selected.

i...............B

G, ...............C

FEO

A. Cold water pipe E.Compression sleeve B. Pipe clamp F Shutoff valve

C.Copper tubing G.Packing nut D.Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the V4" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp

A. Tubeclamp D.Compression nut

B.Tube clamp screw E.Valveinlet

C. Copper tubing

The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install

it in the V4"(6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long enough, a V4" x V4" (6.35 mm x 6.35 mm) coupling is needed

in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the

end of the copper tubing. NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

A B C

A. Refrigerator water tubing

B.Nut (provided)

C.Bulb

D E F G

E. Ferrule (purchased)

F. Nut (purchased)

G. Household water fine

D. Coupling (purchased)

Turn shutoff valve ON.

Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown. NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

Complete the Installation

Electrical Shock Hazard

t/If

A. Bulb B. Nut (provided)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

REFRIGERATOR USE

Temperature Control Adjustment and Cooling On/Off

The refrigerator and freezer control buttons are located on the dispenser panel.

temperature

measure fill fast ice

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Prepare the Water System" or "Water and Ice Dispensers."

NOTE: Allow 24 hours to produce the first batch of ice. Allow 3 days to completely fill ice container.

The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is firm. Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made. The display screen on the dispenser control panel has a

backlight, which will turn off automatically when the control buttons have not been used for 30 seconds or more. When

the backlight is off, the first press of a control button will only reactivate the backlight, without changing any settings.

Within 30 seconds after the backlight has been reactivated, additional presses of control buttons will change the

applicable settings.

To turn cooling off, press and hold the MEASURE FILL and FAST ICE buttons at the same time for 3 seconds. Press and hold

MEASURE FILL and FAST ICE again to turn cooling on. Your refrigerator and freezer will not cool when cooling is off.

For your convenience, your refrigerator and freezer controls are preset at the factory. When you first install your refrigerator, make

sure that the controls are still set to the "mid-settings." To view set points, press the TEMPERATURE button on your

dispenser panel. The factory recommended set points are 0°F (-18°C) for the freezer and 37°F (3°C) for the refrigerator.

IMPORTANT:

• Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your

food may spoil. NOTE: Adjusting the set points to a higher (colder) than

recommended setting will not cool the compartments any faster.

• If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

Adjusting the Controls

To adjust the set points, press the TEMPERATURE button. When

adjust mode is activated, adjusting information will appear on the display screen.

r_ fridge

select zone unit home

The set point for only one compartment (refrigerator or freezer)

appears on the display screen, indicated by "FRIDGE" for the refrigerator or "FREEZER" for the freezer. To change

compartments, press the SELECT ZONE button.

NOTE:ToviewCelsiustemperatures,presstheUNITbutton whenadjustmodeisactivated.Toreturnthedisplaysettingto Fahrenheit,pressUNITagain.

RefrigeratorControls Inadjustmode,makesurethe"FRIDGE"zoneisselected.The

setpointrangefortherefrigeratoris33°Fto45°F(0°Cto7°C).

• Press"-"tolowerthesetpoint.

• Press"+"toraisethesetpoint.

FreezerControls Inadjustmode,makesurethe"FREEZER"zoneisselected.The

setpointrangeforthefreezeris-5°Fto5°F(-21°Cto-15°C).

• Press"-"tolowerthesetpoint.

• Press"+"toraisethesetpoint.

CONDITION: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Setting

1o higher

REFRIGERATOR too warm REFRIGERATOR Setting

1o lower

FREEZER too cold FREEZER Setting

1o higher

FREEZER too warm/too little ice FREEZER Setting

1o lower

Press HOME to exit adjust mode, or allow about 15 seconds of inactivity and adjust mode will turn off automatically.

Disabling Sounds

• To turn off all dispenser and control sounds, including the Door Ajar Alarm, press and hold LIGHT and FAST ICE at the

same time for 3 seconds. IMPORTANT: To avoid unintentionally locking the dispenser

or changing other settings, be sure to press both buttons at exactly the same time.

To turn all sounds back on, press and hold LIGHT and FAST ICE at the same time for 3 seconds again.

The control can be adjusted to properly chill meats or vegetables. The air inside the pan is cooled to avoid "spot" freezing and can

be set to keep meats at the National Livestock and Meat Board recommended storage temperatures of 28 ° to 32°F (-2° to 0°C).

The convertible vegetable/meat drawer control comes preset at

the lowest meat setting.

To store meat:

Set the control to one of the three MEAT settings to store meat at its optimal storage temperature.

To store vegetables:

Set the control to VEG to store vegetables at their optimal storage temperatures.

NOTE: If food starts to freeze, move the control to the left (less cold). Remember to wait 24 hours between adjustments.

Additional Features

NOTE: The display screen on the dispenser control panel has a backlight, which will turn off automatically when the control

buttons have not been used for 30 seconds or more. When the backlight is off, the first press of a control button will only

reactivate the backlight, without changing any settings. Within 30 seconds after the backlight has been reactivated, additional presses of control buttons will change the applicable settings.

Fast Ice

The Fast Ice feature assists with temporary periods of heavy ice use by increasing ice production over a 24-hour period.

• Press the FAST ICE button to turn on the Fast Ice feature. When the feature turns on, "FAST ICE ON" will appear on the

dispenser display. The Fast Ice setting will remain on for 24 hours unless manually turned off.

NOTE: If increased ice production is desired at all times, change the freezer control to a lower setting. Setting the freezer to a colder temperature may make some foods, such as ice cream,

harder. Temperature Alarm This feature constantly monitors the temperatures inside the

refrigerator and freezer, alerting you if either compartment becomes unusually warm for an extended period of time due to a

recent power outage, product malfunction or any other reason. An alarm will sound, "TEMP ALARM" will appear on the display

screen, and the screen will show the highest temperature reached in one of the compartments.

• Press SELECT ZONE to see the highest temperature reached in the other compartment.

• Press and hold RESET ALARM for 3 seconds to turn off the alarm. If internal temperatures have not returned to normal

levels after 15 minutes, the alarm will sound again.

Door Ajar Alarm The Door Ajar Alarm feature sounds an alarm when the

refrigerator or freezer door is open for 5 minutes and the product cooling is turned on. The alarm will repeat every 2 minutes. Close both doors to turn it off. The feature then resets and will

reactivate when either door is left open again for 5 minutes.

You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and

HIGH. LOW (open) for best storage of fruits and vegetables with skins.

HIGH (closed) for best storage of fresh, leafy vegetables.

l)oou I i_"t

Cool air from the freezer is directed to the refrigerator door bin directly beneath the vents.

NOTE: The daip/compartment and can rack are not associated

with the Chilled Door Bin feature.

Chilled Door Bin Control

The chilled door bin control is located on the left-hand side of the

refrigerator compartment.

A. Chilled door bin control

Slide the door chill control to the left or down to reduce the flow of cold air to the bin and make it less cold.

Slide the door chill control to the right or up to increase the flow of cold air to the bin and make it colder.

s ' A Ice ....

Depending on your model, you may have one or more of the following options: the ability to select either crushed or cubed ice, a special light that turns on when you use the dispenser, or a lock option to avoid unintentional dispensing.

NOTES:

• The dispensing system will not operate when the freezer door is open.

• After connecting the refrigerator to a water source, flush the water system. Use a sturdy container to depress and hold the

water dispenser pad for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water

begins to flow, continue depressing and releasing the dispenser pad (5 seconds on, 5 seconds off) for an additional 5 minutes. This will flush air from the filter and water

dispensing system. Additional flushing may be required in some households. As air is cleared from the system, water

may spurt out of the dispenser.

• Allow 24 hours for the refrigerator to cool down and chill water.

Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

The display screen on the dispenser control panel has a backlight, which will turn off automatically when the control buttons have not been used for 30 seconds or more. When

the backlight is off, the first press of a control button will only reactivate the backlight, without changing any settings. Within

30 seconds after the backlight has been reactivated, additional presses of control buttons will change the

applicable settings.

The Water Dispenser

To Dispense Water (Standard):

1. To select water, press the WATER selection button. The display screen will indicate when water is selected.

y water

2. Press a sturdy glass against the dispenser pad OR place the glass below the water dispenser and press the WATER

dispenser button.

3. Remove the glass OR release the button to stop dispensing. NOTE: While dispensing water and for 5 seconds after

dispensing has stopped, the digital display will show how much water has been dispensed.

To Dispense Water (Measured Fill):

Measured Fill allows you to dispense a specified amount of water with the touch of a few buttons.

NOTE: The amount of water you select will be dispensed. Be sure that the container is empty and can hold the entire volume. If

ice is in the container, you may need to adjust your selection.

1. Press MEASURE FILL to turn the feature on. The Measured Fill options will appear on the display screen.

unit home

IMPORTANT: Dispense enough water every week to maintain a

fresh supply.

Water Dispenser Buttons and Pad

There are three dispenser panel buttons primarily used in the water dispensing process:

• In the row of six buttons below the dispenser display screen, the fourth button (from the left) is the WATER selection

button. It is used to select water instead of ice for dispensing.

• Centered below the row of six buttons is the WATER dispenser button. This is used to actually dispense water.

• In the row of six buttons, the fifth button (from the left) is the MEASURE FILL button. This activates the Measured Fill

feature.

light Itemperature

AB C

A. WATERselection button

B.WATERdispenser button

C.MEASUREFILLbutton

The dispenser pad is located on the back wall of the dispenser cavity. When pressed, either water or ice will dispense, depending on the chosen setting.

At any time while Measured Fill is active, press HOME to turn off the feature.

NOTE: The dispenser will automatically turn off Measured Fill after 15 seconds of inactivity.

You can dispense water by the ounce, cup, or liter. Press UNIT to select your desired setting. Default, minimum, and maximum volumes are listed below.

Units Default Minimum Maximum

Ounces 8 1 128

Cups 1 1/4 16 Liters 0.25 0.05 4

Press the "+" and "-" buttons to adjust the volume as desired. NOTE: Most coffee cups (commonly 4 to 6 oz [118 to

177 mL] per cup) are not the same size as a measuring cup (8 oz [237 mL]). You may need to adjust the volume to avoid

unintentionally overfilling coffee cups.

To dispense water, press and hold a sturdy glass against the dispenser pad OR place the glass below the dispenser and

press and release the WATER dispenser button. NOTE: While dispensing water, the digital display will count

down how much water remains to be dispensed, according to the volume you selected. The flow of water will

automatically stop once the desired volume has been dispensed.

To stop dispensing before the entire selected volume has been dispensed, remove the glass from the dispenser pad

OR press and release the WATER dispenser button a second time.

NOTE: To select a new volume or select the same volume again, you must first finish dispensing the selected volume, or

turn off the Measured Fill feature and then turn it back on.

The Ice Dispenser The Dispenser Lock (on some models)

Ice dispenses from the ice maker storage bin in the freezer when the dispenser pad is pressed. The dispensing system will not

operate when the freezer door is open. To turn off the ice maker, see "Ice Maker and Storage Bin."

Your ice maker can produce both crushed and cubed ice. Before dispensing ice, select which type of ice you prefer by pressing

the ICE button on the dispenser panel. The display screen indicates which type of ice is selected.

crushedU cubedU

CRUSHED CUBED

For crushed ice, cubes are crushed before being dispensed. This may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size. When changing from crushed to cubed, a few ounces of crushed

ice will be dispensed along with the first cubes. To Dispense Ice:

1. Press the button to select the desired type of ice.

Cut Hazard

Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

Hold a sturdy glass close to the dispenser opening so ice does not fall outside of the glass. Press the glass against the

dispenser pad or, if necessary, use your index finger or other hand to press the pad while keeping the glass close to the

dispenser opening. IMPORTANT: You do not need to apply a lot of pressure to

the pad in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

NOTE: You can dispense both ice and water at the same time. While using the dispenser pad to dispense ice, press

the WATER dispenser button to also dispense water. Releasing the WATER dispenser button while still pressing

the dispenser pad will not affect ice dispensing.

Remove the glass to stop dispensing. NOTE: Ice may continue to dispense for up to 10 seconds

after removing the glass from the pad. The dispenser may continue to make noise for a few seconds after dispensing.

The Dispenser Light (on some models)

The dispenser can be turned off for easy cleaning or to avoid

unintentional dispensing by small children and pets. NOTE: The lock feature does not shut off power to the

refrigerator, to the ice maker, or to the dispenser light. It simply deactivates the dispenser controls and pad. To turn off the ice

maker, see "Ice Maker and Storage Bin."

• Press and hold TO LOCK for 3 seconds to lock the dispenser.

• Press and hold TO LOCK a second time to unlock the dispenser.

The display screen indicates when the dispenser is locked.

locked

NOTE: If you attempt to change settings or dispense ice/water while the dispenser is locked, "CONTROL LOCKED" will flash on

the display screen.

Turning the Ice Maker On/Off

• To turn on the ice maker, lift open the translucent ice maker door and lower the wire shutoff arm to the ON position.

• To manually turn off the ice maker, lift the wire shutoff arm to the OFF (arm up) position and listen for the click. Ice can still

be dispensed, but no more can be made.

NOTE: Your ice maker has an automatic shutoff. As ice is made, the ice cubes will fill the ice storage bin, and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not force the wire shutoff arm up or down.

REMEMBER:

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

• The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the

ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating

properly and is well maintained.

• Do not use anything sharp to break up the ice in the storage bin. This can cause damage to the ice container and the

dispenser mechanism. Do not store anything on top of or in the ice maker or storage

bin.

Removing and Replacing Ice Storage Bin

1. Lift and hold open the translucent ice maker door.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position. Release the ice maker door.

3. Lift up the front of the storage bin and pull it out.

When you use the dispenser, the light will automatically turn on. If you want the light to be on continuously, you may choose either

ON or DIM. The display screen indicates which mode is selected. ON: Press LIGHT to turn on the dispenser light. DIM: Press LIGHT a second time to select DIM mode. The

dispenser light will remain on, but at a lower intensity. OFF: Press LIGHT a third time to turn off the dispenser light.

The dispenser lights are LEDs that cannot be changed. If it appears that your dispenser lights are not working, see

"Troubleshooting" for more information.

Replace the bin by pushing it in all the way, or the dispenser will not work.

To restart ice production, lift open the ice maker door and push the wire shutoff arm down to the ON position.

Donotusewithwaterthatismicrobiologicallyunsafeorof unknownqualitywithoutadequatedisinfectionbeforeor afterthesystem.

Water Filter Status Light (on some models)

The water filter status light will help you know when to change your water filter. When the water filter status display changes from "GOOD" to "ORDER," this tells you that it is almost time to change the water filter cartridge. Replace the water filter cartridge when the water filter status display changes to "REPLACE." If water flow to your water dispenser or ice maker decreases noticeably, change the filter sooner. The filter should be replaced at least every 6 months depending on your water quality and usage.

After changing the water filter, reset the status light by pressing and holding the FILTER button for 3 seconds. The status light will change from "REPLACE" to "GOOD" when the system is reset.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator: NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water.

Changing the Water Filter

1. Press the eject button to release the filter from the base grille.

2. Pull the filter straight out.

3. Turn the cap counterclockwise to remove it from the filter. IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

4. Align the ridge on the cap with the arrow on the new filter and turn the cap until it snaps into place.

NOTE: You can run the dispenser without a filter. Your water will not be filtered. Simply insert the cap all of the way into the base grille and rotate the cap until it is firmly in place.

5. Remove the covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.

6. Push the filter into the base grille. The eject button will pop back out when the filter is fully engaged.

7. Flush the water system. See "Water and Ice Dispensers."

On some models, wash glass door panels with a clean sponge or soft cloth and a mild detergent in warm water.

NOTES:

Do not hit the glass with pots, pans, furniture, toys, or other objects. Scratching, hitting, jarring or stressing the glass may weaken its structure, causing an increased risk of breakage at a later date.

• Do not close the doors until all shelves, drawers and bins

are in place.

There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not allbulbswillfityourrefrigerator.Be sureto replace thebulbwithone ofthesame size,shape and wattage.On some models,the dispenserlightrequiresa heavy duty10-wattbulb.

Allotherlightsrequirea 40-wattbulb.Replacement bulbsare

availablefrom your dealer.

1. Unplug refrigeratorordisconnectpower.

2. Remove lightshieldwhen applicable. NOTE: To cleanthelightshield,wash itwithwarm waterand

liquiddetergent.Rinseand drytheshieldwell.

3. Remove lightbulband replacewithone ofthesame size,

shape and wattage.

4. Replace light shield when applicable.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

In the U.S.A., www.maytag.com In Canada, www.maytag.ca

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

to possibly avoid the cost of a service call.

• Rattling - flow of refrigerant, water line, or from items placed on top of the refrigerator

• Sizzling/Gurgling - water dripping on the heater during defrost cycle

• Popping - contraction/expansion of inside walls, especially during initial cool-down

• Water running - may be heard when ice melts during the defrost cycle and water runs into the drain pan

• Creaking/Cracking - occurs as ice is being ejected from the ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct position.

The doors are difficult to open

Power cord unplugged? Plug into a grounded 3 prong outlet.

Is outlet working? Plug in a lamp to see if the outlet is working.

Household fuse blown or circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues,

call an electrician. Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls." New installation? Allow 24 hours following installation for

the refrigerator to cool completely. NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its high-efficiency compressor and fans. The refrigerator may run even longer if the room is warm, a large food load is added, doors are opened often, or if the doors have been left open.

The refrigerator is noisy

Refrigerator noise has been reduced over the years. Due to this reduction, you may hear intermittent noises from your new refrigerator that you did not notice from your old model. Below are listed some normal sounds with an explanation.

• Buzzing - heard when the water valve opens to fill the ice maker

• Pulsating - fans/compressor adjusting to optimize performance

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

• Are the gaskets dirty or sticky? Clean gaskets with mild soap and warm water.

The lights do not work

• Is a light bulb loose in the socket or burned out? See "Changing the Light Bulbs."

• Is the dispenser light set to OFF? On some models, the dispenser light will operate only when a dispenser lever/pad is pressed. If you want the dispenser light to stay on continuously, set the dispenser light to ON, or (on some models) NIGHT LIGHT or AUTO or HALF or DIM. See "Water and Ice Dispensers."

• Is the dispenser light set to NIGHT LIGHT or AUTO? On some models, if the dispenser is set to the NIGHT LIGHT or AUTO mode, be sure the dispenser light sensor is not blocked. See "Water and Ice Dispensers."

Temperature is too warm

• New installation? Allow 24 hours following installation for the refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions? Adjust the controls a setting colder. Check temperature in 24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to enter refrigerator. Minimize door openings and keep doors fully closed.

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch (depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice

production.

• Large amount of ice recently removed? Allow 24 hours for ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm? Remove ice from the ejector arm with a plastic utensil.

• Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.

• Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a licensed, qualified plumber.

Off-taste, odor or gray color in the ice

• New plumbing connections? New plumbing connections can cause discolored or off-flavored ice.

• Ice stored too long? Discard ice. Wash ice bin. Allow 24 hours for ice maker to make new ice.

• Odor transfer from food? Use airtight, moisture-proof packaging to store food.

• Are there minerals (such as sulfur) in the water? A water filter may need to be installed to remove the minerals.

• Is there a water filter installed on the refrigerator? Gray or dark discoloration in ice indicates that the water filtration

system needs additional flushing.

The ice dispenser will not operate properly

• Freezer door closed completely? Close the door firmly. If it does not close completely, see "The doors will not close

completely."

• Ice bin installed correctly? Be sure the ice bin is firmly in position.

• New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice production.

• Ice stuck in the delivery chute? Use a plastic utensil to clear the delivery chute.

• Has the wrong ice been added to the bin? Use only cubes produced by the current ice maker.

• Has the ice melted around the auger (metal spiral) in the ice bin? Empty the ice container. Use warm water to melt the

ice if necessary.

Cut Hazard

Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

• Is the ice dispenser stalling while dispensing "crushed" ice? Change the ice button from "crushed" to "cubed." If cubed ice dispenses correctly, depress the button for "crushed" ice and begin dispensing again.

• Has the dispenser arm been held in too long? Ice will stop dispensing when the arm is held in too long. Wait 3 minutes for dispenser motor to reset before using again.

+ 25 hidden pages

Maytag MSD2578VEW00, MSD2578VEM01, MSD2578VEM00, MSD2578VEB00, MSD2578VEA00 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual