Maytag MMW9730AB, MMW9730AW, MMW9730AS Dimension Guide

30" (76.2 CM) ELECTRIC BUILT-IN MICROWAVE/OVEN COMBINATION

PRODUCT MODEL SERIES

PRODUCT DIMENSIONS

MMW9730A

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and the wire gauge are in accordance with local codes.

Check with a qualified electrical installer if you are not sure the oven is properly grounded.

This oven must be connected to a grounded metal, permanent wiring system.

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and all local codes and ordinances.

To properly install your oven, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

●

Oven must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model/serial number rating plate is located near center vent of the lower oven. See the following illustration.

●

Models rated from 7.3 to 9.6 kW at 240 volts (5.4 to

7.4 kW at 208 volts) require a separate 40-amp circuit. Models rated at 4.8 kW and below at 240 volts (3.6 kW and below at 208 volts) require a separate 20-amp circuit.

●

A circuit breaker is recommended.

●

Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored or nonmetallic sheathed, copper cable (with grounding wire). See “Make Electrical Connection” section.

●

Flexible conduit from the oven should be connected directly to the junction box.

●

Do not cut the conduit. The length of conduit provided is for serviceability of the oven.

●

A UL listed or CSA approved conduit connector must be provided.

●

If the house has aluminum wiring follow the procedure below:

1. Connect a section of solid copper wire to the pigtail leads.

2. Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

For power requirements for model MMW9730A, refer to the following table.

Voltage Microwave Oven and Microwave Oven and

Microwave Oven with Microwave Oven with Single Thermal Oven Single Convection Oven

240 VAC 5490 W 5520 W 208 VAC 4590 W 4620 W 240 VAC 30.4 A 30.5 A 208 VAC 28.4 A 28.6 A

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.

Ref. W10351241

2/17/12

ELECTRICAL CONNECTION

Product Dimensions

A. Model/serial number plate

30" (76.2 cm) models

" (108.0 cm) overall height

42⁹⁄₁₆

B. 28

" (72.3 cm) recessed width

¹⁄₂

C. 41" (104.1 cm) recessed height D. 23

" (59.1 cm) max. recessed depth

¹⁄₄

E. 30" (76.2 cm) overall width

Cabinet Dimensions

30" (76.2 cm) models

" (76.2 cm) min. cabinet width

B. 1" (2.5 cm) top of cutout to bottom of upper cabinet door C. 19

" (48.9 cm) bottom of cutout to floor is recommended.

¹⁄₄

4"-19

" (10.2-48.9 cm) bottom of cutout to floor is acceptable.

¹⁄₄

D. 28

" (72.4 cm) cutout width

¹⁄₂

E. 1

" (3.8 cm) min. bottom of cutout to top of cabinet door

¹⁄₂

" (105 cm)* recommended cutout height

F. 4 1

⁵⁄₁₆

G. 24" (60.7 cm) cutout depth

*NOTE: The cabinet height can be between 41" (104.1 cm) and

41½" (105.6 cm) for microwave/oven combination.