Maytag MLE20PNAGW, MLE20PNBGW, MLG20PDBGW, MLE20PNCGW, MLE20PDCGW Installation Instructions

...

INSTALLATION

INSTRUCTIONS

CommerCial StaCked

WaSher/dryer

GaS or eleCtriC

INSTRUCTIONS

D’INSTALLATION

lave-linGe/SèChe-linGe SuperpoSéS

à uSaGe CommerCial

à Gaz ou éleCtrique

INSTRUCCIONES

DE INSTALACIÓN

MLE20PD MLG20PD MLE20PN

lavadora/SeCadora ComerCialeS

apiladaS a GaS o eléCtriCaS

ISTRUZIONI

D’INSTALLAZIONE

lavatriCe/aSCiuGatriCe

CommerCiale a Colonna

a GaS o elettriCa

W10335466C

www.maytagcommerciallaundry.com

TABLE OF CONTENTS

(Australia and New Zealand Installations)

Page

Stacked Washer/Dryer Safety .................................................................. 3

Stacked Washer/Dryer Disposal ............................................................. 6

Tools & Parts ..................................................................................................... 7

Alternate Parts and Accessories ............................................................. 8

Dimensions/Clearances ............................................................................. 9

Stacked Washer/Gas Dryer Installation Requirements .......... 10

Stacked Washer/Electric Dryer

Installation Requirements ....................................................................... 13

Dryer Venting Requirements ................................................................. 15

Dryer Gas Supply Requirements ......................................................... 17

Installing Stacked Washer/Dryer ......................................................... 18

Washer Drain System ................................................................................ 21

Leveling ............................................................................................................. 22

Complete Installation ................................................................................. 23

Reversing Dryer Door Swing .................................................................. 24

Stacked Washer/Dryer Maintenance Instructions ...................... 26

If You Need Assistance ............................................................................. 27

Technical Speciﬁcations – Gas Dryer ................................................ 28

Electronic Control Setup Instructions ............................................... 29

Warranty ........................................................................................................... 35

ÍNDICE

Página

Seguridad de la lavadora/secadora apiladas ................................. 71

Eliminación de la lavadora/secadora apiladas .............................. 74

Herramientas y piezas ................................................................................. 75

Piezas y accesorios adicionales ........................................................... 76

Dimensiones y espacios libres .............................................................. 77

Requisitos de instalación de la lavadora/secadora

a gas apiladas ................................................................................................. 78

Requisitos de instalación de la lavadora/

secadora eléctricas apiladas .................................................................. 81

Requisitos de ventilación de la secadora ........................................ 83

Requisitos del suministro de gas de la secadora ....................... 86

Instalación de la lavadora/secadora apiladas ................................ 87

Sistema de desagüe de la lavadora ..................................................... 90

Nivelación ...........................................................................................................91

Complete la instalación ............................................................................. 92

Cómo invertir el cierre de la puerta de la secadora .................... 93

Instrucciones de mantenimiento

de la lavadora/secadora apiladas .........................................................95

Si necesita ayuda ...........................................................................................96

Especiﬁcaciones técnicas – secadora a gas ................................. 97

Instrucciones de programación del control electrónico ........... 98

Garantía ........................................................................................................... 105

TABLE DES MATIÈRES

Page

Sécurité du lave-linge/sèche-linge superposés ........................... 36

Élimination du lave-linge/sèche-linge superposés ..................... 39

Outils et pièces .............................................................................................. 40

Pièces supplémentaires et accessoires ........................................... 41

Dimensions/Distances de dégagement ........................................... 42

Exigences d’installation pour

le lave-linge/sèche-linge à gaz superposés ................................... 43

Exigences d’installation pour le lave-linge/sèche-linge

électriques superposés ............................................................................ 46

Exigences concernant l’évacuation du sèche-linge .................... 48

Spéciﬁcations de l’alimentation en gaz du sèche-linge ........... 51

Installation du lave-linge/sèche-linge superposés .................... 52

Système d’évacuation du lave-linge .................................................... 55

Nivellement .......................................................................................................56

Achever l’installation .................................................................................... 57

Inversion du sens d’ouverture de la porte du sèche-linge ......58

Instructions d’entretien du lave-linge/

sèche-linge superposés ...........................................................................60

Si vous avez besoin d’assistance .........................................................61

Fiche technique – sèche-linge à gaz .................................................. 62

Instructions de réglage du tableau

de commande électronique ..................................................................... 63

Garantie .............................................................................................................. 70

INDICE

Pagina

Sicurezza della lavatrice/asciugatrice impilati ........................... 106

L’eliminazione della lavatrice/asciugatrice impilati .................. 109

Attrezzi e componenti ............................................................................. 110

Parti ed accessori alternati .................................................................... 111

Dimensioni/spazi ...................................................................................... 112

Requisiti dell’installazione della lavatrice/asciugatrice

a gas impilati ............................................................................................... 113

Requisiti dell’installazione della lavatrice/asciugatrice

elettrica impilat ........................................................................................... 116

Requisiti di scarico dell’asciugatrice .............................................. 118

Requisiti di alimentazione del gas dell’asciugatrice .............. 120

Installazione della lavatrice/asciugatrice impilati ..................... 121

Sistema dello scolo della lavatrice .................................................. 124

Livellamento ................................................................................................. 125

Completamento dell’installazione ................................................... 126

Inversione della rotazione di apertura dell’asciugatrice ...... 127

Istruzioni di manutenzione della lavatrice/

asciugatrice impilat .................................................................................... 129

Se avete bisogno dell’assistenza ..................................................... 130

Dati tecnici – asciugatrice a gas ....................................................... 131

Conﬁgurazione dei controlli elettronici ......................................... 132

Garanzia ......................................................................................................... 139

STACKED WASHER/DRYER SAFETY

n It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer smells gas. This information should be obtained from your gas supplier.

n Post the following warning in a prominent location.

FOR YOUR SAFETY

1. DO NOT USE OR STORE PETROL OR OTHER FLAMMABLE MATERIALS IN THIS APPLIANCE OR NEAR THIS APPLIANCE.

2. DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

3. DO NOT MODIFY THIS APPLIANCE.

STACKED WASHER/DRYER SAFETY

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of ﬁre, electric shock, or injury to persons when using the washer/dryer, follow basic precautions,

including the following:

n Read all instructions before using the washer/dryer. n This dryer is intended only for drying clothes and textiles

that have been washed in water. Do not use for any other purpose.

n WARNING: If you smell gas, do not use the dryer or any

electrical equipment nearby. Warn other people to clear the area. Contact the dryer owner immediately.

n Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch ﬁre.

n If it is unavoidable that fabrics that contain vegetable or

cooking oil or that have been contaminated by hair care products be placed in a tumble dryer, they should ﬁrst be washed in hot water with extra detergent – this will reduce, but not eliminate the hazard.

n Do not wash or dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with petrol, dry-cleaning solvents, other ﬂammable, or explosive substances as they give off vapors that could ignite or explode.

n Items that have been soiled with substances such

as acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes, and wax removers should be washed in hot water with extra detergent before being dried in the dryer.

n Do not add gasoline, dry-cleaning solvents, or other

ﬂammable, or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

n Do not dry unwashed items in the dryer. n Do not use this dryer if industrial chemicals have been used

for cleaning. The possible presence of residual quantities of aggressive or decomposed chemicals in the load may produce damage to the dryer and harmful fumes.

n Do not allow children to play on or in the washer/dryer.

Close supervision of children is necessary when the washer/dryer is used near children.

n This dryer is not intended for use by persons (including

children) with reduced physical, sensory, or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning use of the dryer by a person responsible for their safety.

n Before the washer/dryer is removed from service

or discarded, remove the doors to the washer/dryer compartments.

n Do not reach into the washer/dryer if the tub, agitator

or drum is moving.

n Do not open door while dryer is in operation. It will stop. n When loading or re-loading the dryer, avoid touching hot

metal parts of the drum (burn risk).

SAVE THESE INSTRUCTIONS

n If drum rotation is blocked due to trapped textiles,

disconnect the dryer from the electrical supply before gently removing the blockage.

n If the dryer is not heating, or appears to be defective or

damaged, do not use it. Contact the owner.

n Do not install or store the washer/dryer where it will be

exposed to the weather.

n Do not tamper with controls. n Clean dryer lint screen before or after each load. n Do not use this dryer without the lint screen in place. n Under certain conditions, hydrogen gas may be produced

in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the washer, turn on all hot water faucets and let the water ﬂow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is ﬂammable, do not smoke or use an open ﬂame during this time.

n Do not repair or replace any part of the washer/dryer or

attempt any servicing unless speciﬁcally recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.

n Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric softener or product.

n Do not use heat to dry articles containing foam rubber

or similarly textured rubber-like materials.

n The ﬁnal part of a tumble dryer cycle occurs without heat

(cool-down cycle) to ensure that the articles are left at a temperature that ensures that the items will not be damaged.

n WARNING: Never stop a tumble dryer before the end

of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. (Avoids risk of spontaneous combustion).

n In case of electrical supply failure, remove the load quickly

and spread it out to avoid risk of spontaneous combustion.

n Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust, and dirt.

n The fresh air ventilation openings into the room and into

the dryer must not be blocked or sealed.

n Emergency stop control: The mains plug should be removed

in an emergency.

n The interior of the dryer and dryer exhaust vent should be

cleaned periodically by qualiﬁed service personnel.

n See “Electrical Requirements” section of the Installation

Instructions booklet for grounding instructions.

STACKED WASHER/DRYER DISPOSAL

GPO, Schorndorf

Name and signature of aurthorised person

GPO, Schorndorf

Name and signature of aurthorised person

MODEL NOMENCLATURE:

MLE – Maytag Electric PD – Electronic Control – Coin Drop Enabled MLG – Maytag Gas PN – Electronic Control – Non-Pay 20 – Model Type Number

EU - DECLARATION OF CONFORMITY

CE - DECLARATION DE CONFORMITE

We BAUKNECHT HAUSGERÄTE GmbH, D-73614 Schorndorf representing WHIRLPOOL EUROPE S.r.l I-21025 COMERIO

declare under our sole responsibility that the product

Commercial stacked pair washer / dryer MAYTAG MLE 20PN

to which this declaration relates is in conformity with the following standard(s) or other normative document(s)

EN 60335-1:2002+A1+A2+A11+A12+A13+A14+A15 EN 60335-2-7:2010 EN 60335-2-11:2010 EN 62233:2008 EN 61770:1999+A1:2004+A2:2006 EN ISO 10472-1:2008 EN ISO 10472-2:2008 EN ISO 14121-1:2007 EN 55014-1:2006+A1:2009 EN 55014-2:1997+A1:2001+A2:2008 EN 61000-3-2:2006+A1:2009+A2:2009 EN 61000-3-11:2000

following the provisions of Directive(s

2006/42/EC MACHINERY DIRECTIVE 2004/108/EC ELECTROMAGNETIC COMPATIBILITY DIRECTIVE 2011/65/EU ROHS DIRECTIVE 2002/96/EC WEEE DIRECTIVE

Schorndorf, 28.02.2012 Micael Zirondi Karl-Dieter Klingenstein

Place and date: Director PDC FC EMEA Product Approval

MAYTAG MLE 20PD

represented by

EU - DECLARATION OF CONFORMITY

CE - DECLARATION DE CONFORMITE

We BAUKNECHT HAUSGERÄTE GmbH, D-73614 Schorndorf representing WHIRLPOOL EUROPE S.r.l I-21025 COMERIO

declare under our sole responsibility that the product

Commercial gas dryer MAYTAG MLG 20PD

to which this declaration relates is in conformity with the following standard(s) or other normative document(s)

EN 60335-1:2002+A1+A2+A11+A12+A13 (+A14+A15 only electrical part) EN 60335-2-11:2010 EN 60335-2-102:2006+A1 EN 62233:2008 EN 12752-1:1999 EN ISO 10472-1:2008 EN ISO 10472-4:2008 EN ISO 14121-1:2007 EN 55014-1:2006+A1:2009 EN 55014-2:1997+A1:2001+A2:2008 EN 61000-3-2:2006+A1:2009+A2:2009 EN 61000-3-11:2000

following the provisions of Directive(s):

2006/42/EC MACHINERY DIRECTIVE 2009/142/EC EUROPEAN GAS APPLIANCE DIRECTIVE 2004/108/EC ELECTROMAGNETIC COMPATIBILITY DIRECTIVE 2011/65/EU ROHS DIRECTIVE 2002/96/EC WEEE DIRECTIVE

Schorndorf, 19.04.2012 Micael Zirondi Karl-Dieter Klingenstein

Place and date: Director PDC FC EMEA Product Approval

represented by

Nom et signature de la personne autorisée

TOOLS & PARTS

Tools Needed:

203 mm (8") 203 mm (8") or 254 mm (10") Flat-Blade Screwdriver Phillips Screwdriver or 254 mm (10") Adjustable Wrench Pipe Wrench that opens to 25 mm (1")

Torx®† T-20 Security 25 mm (1") Hex-Head 8 mm (5/16") Socket Wrench Pliers Screwdriver or Bit Socket Wrench (that open to 39 mm [19/16"])

Level Utility Knife 6 mm (1/4") Nut Driver Locking Pliers

Caulk Gun and Caulk Vent Clamps Pipe-Joint Compound 686 mm (27") Wood Block (for installing new exhaust vent) suitable for gas type

Flashlight (optional) 13 mm (1/2") and 14 mm Ruler or Measuring Tape (9/16") Open-End Wrenches

Parts Supplied:

Water Inlet Hoses (2) Inlet Hose Washers (4) U-Shaped Hose Form Transit Bolt Hole Plug (4)

Beaded Tie Strap

Drain Hose/Clamp

†® TORX is a registered trademark of Saturn Fasteners, Inc.

ALTERNATE PARTS AND ACCESSORIES

Alternate Parts

Your installation may require additional parts. If you are interested in purchasing one of the items listed here, call the toll-free number in the “If You Need Assistance” section.

If You Have You Will Need to Buy

Overhead sewer Standard 76 L (20 gal.) 990 mm

(39") tall drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers)

25 mm (1") standpipe 51 mm (2") diameter to 25 mm (1")

diameter Standpipe Adapter Part Number 3363920 Connector Kit Part Number 285835

Drain hose too Extension Drain Hose Part short Number 285863 Connector Kit Part Number 285835

Lint clogged drain Drain Protector Part Number 367031 Connector Kit Part Number 285835

Floor drain system Siphon break, Part Number 285834

Connector Kit (x2) Part Number 285835 Extension Drain Hose Part Number 285863

Water faucets 2 longer water ﬁll hoses: beyond reach 1.8 m (6 ft.) 90° bend hose of ﬁll hoses Part Number 76314

3.0 m (10 ft.) Part Number 350008

Accessories

Enhance your washer/dryer with these premium accessories. For more high-quality items or to order, contact your authorized

Maytag distributor.

Part Number Accessory 8212526 Washer drip tray, ﬁts under all 31682 All-purpose appliance cleaner 1903WH Laundry supply storage cart 279818 3-way dryer venting kit 285834 Siphon break kit

DIMENSIONS/CLEARANCES

Dimensions

Front View Side View Back View

Clearances

Side Clearances Back/Top Clearances

STACKED WASHER/GAS DRYER INSTALLATION REQUIREMENTS

(Australia and New Zealand – for full details of installation requirements refer to AS/NZS 5601.1 – Gas Installations)

Stacked Washer/Gas Dryer Location

Stacked washer/gas dryer installation clearances

n The location must be large enough to allow the washer and dryer

doors to be fully opened.

n Additional spacing should be considered for ease of installation

and servicing. The doors open more than 180°. The washer door is not reversible.

n Additional clearances might be required for wall, door, and ﬂoor

moldings.

n Additional spacing of 25 mm (1") on all sides of the washer/dryer

is recommended to reduce noise transfer.

n Companion appliance spacing should also be considered.

When installing a gas dryer:

IMPORTANT: Observe all governing codes and ordinances.

n Check code requirements: Some codes limit or do not permit

installation of clothes dryers in garages, closets, or sleeping

Selecting the proper location for your washer/dryer improves performance and minimizes noise and possible washer “walk.”

Your washer/dryer can be installed in a basement, laundry room, or recessed area. See “Drain System.”

Companion appliance location requirements should also be considered.

IMPORTANT: Do not install or store the washer/dryer where it will be exposed to the weather. Do not store or operate the washer/ dryer in temperatures at or below 0°C (32°F). Some water can remain in the washer and can cause damage in low temperatures. Proper installation is your responsibility.

You will need:

n A water heater set to deliver 49°C (120°F) water to the washer. n A grounded electrical outlet located within 1.8 m (6 ft.) of

where the power cord is attached to the back of the washer. See “Electrical Requirements.”

n Hot and cold water faucets located within 1.2 m (4 ft.)

of the hot and cold water ﬁll valves, and water pressure of 137.9–689.6 kPa (20–100 psi).

n A level ﬂoor with a maximum slope of 25 mm (1") under

entire washer/dryer. Installing the washer/dryer on soft ﬂoor surfaces, such as carpets or surfaces with foam backing, is not recommended.

n A sturdy and solid ﬂoor to support the washer/dryer with a total

weight (water and load) of 204 kg (450 lbs).

n A ﬂoor drain under the bulkhead. Prefabricated bulkheads with

electrical outlets, water inlet lines, and drain facilities should be used only where local codes permit.

quarters. Contact your local building inspector.

NOTE: For installation in Australia and New Zealand, install

dryer in accordance with AS/NZS 5601.1 and local governance codes.

n Make sure that lower edges of the cabinet, plus the back and

bottom sides of the washer, are free of obstructions to permit adequate clearance of air openings for combustion air. See “Recessed Area and Closet Installation Instructions” below for minimum spacing requirements.

n Do not install on carpet.

Recessed Area and Closet Installation Instructions

This washer/dryer may be installed in a recessed area or closet. This washer/dryer must not be installed behind a lockable door, a sliding door, or a door with a hinge on the opposite side to that of the washer/dryer. For recessed area and closet installations, minimum clearances can be found on the warning label on the rear of the dryer or in “Dimensions/Clearances.”

The installation spacing is in millimeters and is the minimum allowable. Additional spacing should be considered for ease of installation, servicing, and compliance with local codes and ordinances.

If closet door is installed, the minimum unobstructed air opening in the top and bottom is required. Louvered doors with equivalent air openings are acceptable.

The dryer must be exhausted outdoors. No other fuel-burning appliance may be installed in the same closet

as the washer/dryer. NOTE: For installation in Australia and New Zealand, refer to

AS/NZS 5601.1 for ventilation requirements.

STACKED WASHER/GAS DRYER INSTALLATION

Stacked Washer/Gas Dryer Electrical Requirements

IMPORTANT: Observe all governing codes and ordinances.

You will need an earthed electrical outlet located within 610 mm (2 feet) of either side of the washer/dryer.

This washer/dryer is supplied/ﬁtted with an electrical supply cord and plug. It should be connected to electrical supply socket at the voltage shown on the rating plate. The minimum supply fuse capacity should be 5A. The washer/dryer must be positioned so that the plug is clearly visible and accessible. This plug also provides the function of an emergency stop control for the user. If the ﬁtted plug is not used, the electrical connection must be carried out by a competent electrician in accordance with local or national codes.

If the supply cord is damaged, it must be replaced with a specially terminated cord by an authorized service agent or a similarly competent person in order to avoid a hazard.

Do not use an adapter. Do not use an extension cord. NOTE: In accordance with the European EMC Directive

(2004/108/EC), the maximum electricity supply system impedance to which the gas dryer should be connected is declared to be 0.054 Ohm + j0.034 Ohm.

NOTE: Electrical safety standards: The manufacturer has chosen compliance with IEC/EN.60335 standards as the most appropriate for this product.

REQUIREMENTS

EARTHING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Using the universal cord included with this dryer:

The gas dryer is equipped with a universal cord with interchangeable plugs.

1. To use the universal cord, select the plug end that ﬁts your electrical outlet, and plug it into the adapter on the supply cord.

2. Secure the plug end in place on the cord by aligning the 2 cover halves over the cord adapter and clipping them together.

If codes permit and an additional earth bond wire is used, it is recommended that a qualiﬁed electrician determine that the earth bond path is adequate.

STACKED WASHER/GAS DRYER INSTALLATION REQUIREMENTS

Stacked Washer/Gas Dryer Gas Supply Requirements

Supply line requirements:

Provide a rigid gas supply line to the washer/dryer location. It should be minimum 12.5 mm (1/2") ID. When acceptable to the gas supplier and local codes, 10 mm (3/8") ID rigid supply line may be used for lengths under 6.1 m (20'). Pipe-joint compounds resistant to the action of L.P. gas must be used.

NOTE: For installation in Australia and New Zealand, refer to AS/NZS 5601 for pipe sizing details. All piping is to be in accordance with AS/NZS 5601.1 – Gas Installations.

Gas connection to the dryer itself should be made by means of a ﬂexible gas hose suitable for the appliance and gas category in accordance with national installation regulations. If in doubt, contact the gas supplier. It should be minimum 10 mm (3/8") ID.

A means of restraint should be used between the washer/dryer and the wall to avoid straining of the rigid gas supply when the washer/dryer is moved. An appropriate length of chain and a wall hook is recommended.

The dryer gas inlet connection is a 3/8" NPT thread. An adapter is supplied for conversion to standard ISO.228-1 thread (3/8" BSP).

Check for leaks by using an approved noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leak found. A

IMPORTANT: Observe all governing codes and ordinances. In Australia and New Zealand, refer to AS/NZS 5601.1 – Gas Installations.

Gas Supply

Before installation, check that the local gas distribution conditions, nature of gas and pressure, and the adjustment of the appliance are compatible. Burner information will be found on the model/ serial rating plate in the door recess of the dryer. If this information does not agree with the type of gas available, see your dealer.

Natural Gas:

This dryer is factory adjusted for use with NATURAL GAS (G20), and no further adjustment should be required at installation.

L.P. Gas:

This dryer is also certiﬁed for use with L.P. (propane or butane) gases with appropriate conversion. No attempt shall be made to convert the appliance from the gas speciﬁed on the model/serial rating plate for use with a different gas without consulting the serving gas supplier.

Conversion must be done by a competent service technician. Gas conversion kit (European Country), part number W10233219, is available for purchase from your dealer. Gas conversion kit (Australia), part number W10315369, is available for purchase from your dealer. Full instructions are supplied with the kit.

Natural gas (France/Belgium):

This dryer is also certiﬁed for France/Belgium for use with G20/ G25 gases (20 mbar/25 mbar) with appropriate conversion. No attempt should be made to convert this appliance from the gas speciﬁed on the gas rating label for use with a different gas without consulting the serving gas supplier. Gas conversion must be done by a qualiﬁed gas service technician. Conversion kit, part number (W10181947) is available for purchase from your dealer. Full instructions are supplied with the kit.

pressure measurement tapping is provided on the gas valve within the dryer, accessible after removal of the lower front panel.

The dryer must be disconnected from the gas supply piping system during any pressure testing of that system.

STACKED WASHER/ELECTRIC DRYER INSTALLATION

Stacked Washer/Electric Dryer Location

NOTE: In Australia and New Zealand, refer to AS/NZS 5601.1 – Gas Installations.

Selecting the proper location for your washer/dryer improves performance and minimizes noise and possible washer “walk.”

Your washer/dryer can be installed in a basement, laundry room, or recessed area. See “Drain System.”

Companion appliance location requirements should also be considered.

You will need:

n A water heater set to deliver 49°C (120°F) water to the washer. n A grounded electrical outlet located within 1.8 m (6 ft.) of

where the power cord is attached to the back of the washer. See “Electrical Requirements.”

n Hot and cold water faucets located within 1.2 m (4 ft.)

of the hot and cold water ﬁll valves, and water pressure of 137.9–689.6 kPa (20–100 psi).

n A level ﬂoor with a maximum slope of 25 mm (1") under

entire washer/dryer. Installing the washer/dryer on soft ﬂoor surfaces, such as carpets or surfaces with foam backing, is not recommended.

n A sturdy and solid ﬂoor to support the washer/dryer with a total

weight (water and load) of 204 kg (450 lbs).

n A ﬂoor drain under the bulkhead. Prefabricated bulkheads with

electrical outlets, water inlet lines, and drain facilities should be used only where local codes permit.

REQUIREMENTS

Stacked washer/electric dryer installation clearances

n The location must be large enough to allow the washer

and dryer doors to be fully opened.

n Additional spacing should be considered for ease of installation

and servicing. The doors open more than 180°. The washer door is not reversible.

n Additional clearances might be required for wall, door, and ﬂoor

moldings.

n Additional spacing of 25 mm (1") on all sides of the washer/dryer

is recommended to reduce noise transfer.

n Companion appliance spacing should also be considered.

Recessed Area and Closet Installation Instructions

The installation spacing is in millimeters and is the minimum allowable. Additional spacing should be considered for ease of installation, servicing, and compliance with local codes and ordinances.

If closet door is installed, the minimum unobstructed air opening in the top and bottom is required. Louvered doors with equivalent air openings are acceptable.

The dryer must be exhausted outdoors. No other fuel-burning appliance may be installed in the same closet

as the washer/dryer.

STACKED WASHER/ELECTRIC DRYER INSTALLATION REQUIREMENTS

Stacked Washer/Electric Dryer Electrical Requirements

This washer/dryer is supplied without an electric cord and plug. It must be connected by a competent electrician to a single-phase electricity supply at the voltage shown on the dataplate, using a suitable ﬁxed wiring installation in accordance with local and national wiring regulations.

n A 3-wire circular cord of minimum conductor size 2.5 mm2

cross-section area should be used.

n A 30A supply fuse should be used, and a switch having

a contact separation in both poles that provides full disconnection under over-voltage category III conditions must be incorporated into the ﬁxed wiring in accordance with local wiring regulations. The washer/dryer should be positioned so that the disconnection switch is clearly visible and easily accessible to the user. This disconnection switch also provides the function of an emergency stop control for the user.

n A cord clamp bush is provided on the washer/dryer, and

should be tightened on completion of wiring. The electrical mains terminals are located behind the small rear access panel (terminal block cover), and connections should be made in accordance with the terminal markings. Remember to replace the terminal access panel (terminal block cover).

NOTE: In accordance with the European EMC Directive (2004/108/EC), the maximum electrical supply system impedance to which the electric dryer should be connected is declared to be

0.054 Ohm + j0.034 Ohm. NOTE: Electrical safety standards: The manufacturer has

chosen compliance with IEC/EN.60335 standards as the most appropriate for this product.

This is 3-wire appliance which must be earthed.

If codes permit and an additional earth bond wire is used, it is recommended that a qualiﬁed electrician determine that the earth bond path is adequate.

Recommended Earthing Method

It is your responsibility to contact a qualiﬁed electrical installer to ensure that the electrical installation is adequate and in conformance with all local codes and ordinances.

DRYER VENTING REQUIREMENTS

Elbows:

■ 45° elbows provide better airﬂow than 90° elbows.

WARNING: To reduce the risk of ﬁre, this dryer MUST BE EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances. In Australia and New Zealand, refer to AS/NZS 5601.1 – Gas Installations.

■ Following these venting requirements will minimise ducting air

noise.

■ Adequate ventilation has to be provided to avoid the backﬂow

of gases into the room from appliances burning other fuels, including open ﬁres (i.e. available airﬂow into the room should match airﬂow out from the room).

■ Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building. Only rigid or ﬂexible metal vent shall be used for exhausting.

■ Do not use an exhaust hood with a magnetic latch.

102 mm

(4")

102 mm (4") Heavy, Metal Exhaust Vent

■ Only a 4" (102 mm) heavy, metal exhaust vent and clamps may

be used.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■ Must be fully extended and supported in ﬁnal dryer location.

■ Remove excess to avoid sagging and kinking that may result in

reduced airﬂow and poor performance.

■ Do not install in enclosed walls, ceilings, or ﬂoors.

■ The total length should not exceed 7

■ An exhaust hood should cap the vent to keep rodents and

insects from entering the building.

NOTE: If using an existing vent system, clean lint from entire length of the system and make sure exhaust hood is not plugged with lint. Replace plastic or metal foil vents with rigid metal or ﬂexible metal vents. Review “Vent System Chart” and if necessary, modify existing vent system to achieve best drying performance.

⁄4 ft. (2.4 m).

Good

■ Plan installation to use the fewest number of elbows and turns.

■ Allow as much room as possible when using elbows or making

Better

turns. Bend vent gradually to avoid kinking.

■ Vent outlet is located at the center of the bottom dryer back.

■ The vent can be routed up, down, left, right, behind the dryer,

or straight out the back of the dryer.

Clamps:

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct and catch lint. Do not use duct tape.

Improper venting can cause moisture and lint to collect indoors, which may result in:

Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc.

Housecleaning problems and health problems.

DRYER VENTING REQUIREMENTS

(In Australia and New Zealand, refer to AS/NZS 5601.1 – Gas Installations)

Vent Hoods

102 mm (4") Diameter Exhaust Hoods

Box Hood Louvered Hood Angled Hood

Vent System Length

Maximum Vent Length/Vent Connection

Maximum length of vent system depends upon the type of vent used, number of elbows, and type of exhaust hood.

Exhaust hood must be at least 305 mm (12") from the ground or any object that may be in the path of the exhaust (such as ﬂowers, rocks, bushes, or snow).

3. Tighten hose clamp with Phillips screwdriver.

12" min.

305 mm min.

(305 mm)

(12")

Vent System Chart (Rigid Metal Vent) No. of Box and Angled

90˚ Turns Louvered Hood Hood 0 39.6 m (130 ft.) 39.3 m (129 ft.)

1 38.1 m (125 ft.) 36.3 m (119 ft.) 2 35.1 m. (115 ft) 33.2 m (109 ft.) 3 32.3 m (106 ft.) 30.5 m (100 ft.) 4 29.9 m (98 ft.) 28.0 m (92 ft.)

For vent systems not covered by the vent speciﬁcation chart, see your parts distributor.

Provision must be made for enough air for combustion and ventilation. (Check governing codes and ordinances.) See “Recessed Area and Closet Installation Instructions” in the “Stacked Washer/Gas Dryer Location” and “Stacked Washer/ Electric Dryer Location” sections.

A 102 mm (4") outlet hood is preferred. However, a 64 mm (21⁄2") outlet exhaust hood may be used. A 64 mm (21⁄2") outlet creates greater back pressure than other hood types. For permanent installation, a stationary vent system is required.

Connect Vent

1. If connecting to existing vent, make sure the vent is clean.

2. Using a 102 mm (4") clamp, connect vent to exhaust outlet in

dryer.

Vent Collar

4. Make sure the vent is secured to exhaust hood with a 102 mm

(4") clamp.

5. Move dryer into ﬁnal position. Do not crush or kink vent. Make sure dryer is level.

NOTE: Do not remove vent collar.

DRYER VENTING REQUIREMENTS

(In Australia and New Zealand, refer to AS/NZS 5601.1 – Gas Installations)

If an Exhaust Hood Cannot be Used Multiple Dryer Venting

The outside end of main vent should have a sweep elbow directed downward.

* Minimum clearance above any

accumulation of snow, ice, or debris such as leaves

A main vent can be used for venting a group of dryers. The main vent should be sized to remove 5663 l/min. (200 CFM) of air per dryer. Large-capacity lint screens of proper design may be used in main vent if checked and cleaned frequently. The room where the dryers are located should have make-up air equal to or greater than CFM of all the dryers in the room.

Back-draft Damper Kit, Part No. 3391910, is available from your distributor and should be installed in the vent of each dryer to keep exhausted air from returning into dryers and to keep exhaust in balance within main vent. Unobstructed return air openings are required.

Each vent should enter the main vent at an angle pointing in the direction of the airﬂow. Vents entering from the opposite side should be staggered to reduce the exhausted air from interfering with the other vents.

30˚ max.

If main vent travels vertically through the roof, rather than through wall, install a 180° sweep elbow on end of vent at least 610 mm (2 ft.) above surface of roof.

The opening in wall or roof shall have a diameter 13 mm (1⁄2") larger than vent diameter. Vent should be centered in opening.

Do not install screening over end of vent for best performance.

DRYER GAS SUPPLY REQUIREMENTS

(All piping is to be in accordance with AS/NZS 5601.1 – Gas Installations)

Make Gas Connection

air ow

The maximum angle of each vent entering the main vent should be no more than 30°.

Keep air openings free of dry cleaning ﬂuid fumes. Fumes create acids which, when drawn through the dryer heating units, can damage dryers and items being dried.

A clean-out cover should be located on the main vent for periodic cleaning of the vent system.

1. Remove red cap from gas pipe.

2. Connect gas supply to dryer. If the ﬂexible gas hose has

10 mm (3/8") BSP thread, use the supplied conversion thread adapter. Use pipe-joint compound resistant to the action of L.P. gas for gas connections.

If necessary for service, open the toe panel. Use a putty knife to press on the 2 toe panel locks located at the top of the toe panel. Pull downward on the toe panel to open. Toe panel is hinged at the bottom.

3. Open the shut-off valve in the gas supply line.

4. Test all connections by brushing on an approved noncorrosive

leak-detection solution. Bubbles will show a leak. Correct any leaks found.

INSTALLING STACKED WASHER/DRYER

Remove Transport System

NOTE: Slide washer/dryer onto cardboard or hardboard before

moving to avoid damaging ﬂoor covering.

IMPORTANT: Position the washer/dryer so that the rear of the washer is within approximately 900 mm (3 ft.) of its ﬁnal location.

There are four shipping bolts in the rear panel of the washer that support the suspension system during transportation. These bolts also retain the power cord inside the washer until the bolts are removed.

IMPORTANT: Remove the four shipping bolts at the rear of the washer before operation.

1. Keep the washer/dryer in the upright position while removing the shipping bolts.

2. Using a 13 mm (1/2") wrench, loosen each of the bolts.

4. Models with separate washer power cords: Push the power

cord plug into the opening on the right side of the rear panel and pull the power cord through the opening on the left side of the rear panel and close holes with the attached cap. Do not pull plug end of power cord through the right side hole.

NOTE: To avoid damage to internal washer parts or the power cord, if the cord does not pull out of the washer rear panel easily, do not force it. Remove the washer rear panel and guide the power cord around the obstruction and out the hole on the left side of the rear panel.

3. Once the bolt is loose, move it to the center of the hole and completely pull out the bolt, including the plastic spacer covering the bolt. Once all 4 bolts are removed, discard the bolts and spacers.

5. Close the bolt holes with the 4 transport bolt hole plugs.

IMPORTANT: If the washer/dryer is to be transported, call your

product distributor or installer. To avoid suspension and structural damage, your washer/dryer must be properly set up for relocation by a trained professional.

INSTALLING STACKED WASHER/DRYER

Connect Inlet Hoses

Insert new hose washers (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings.

CouplingWasher

Connect Inlet Hoses to Water Faucets

Make sure the washer drum is empty.

1. Attach a hose to the hot water faucet. Screw on coupling

by hand until it is seated on the washer.

Connect Inlet Hoses to Washer

1. Attach the cold water hose to the washer’s cold water inlet

valve. Screw on coupling by hand until it is seated on the washer.

2. Attach the hot water hose to the washer’s hot water inlet valve. Screw on coupling by hand until it is seated on the washer.

2. Attach a hose to the cold water faucet. Screw on coupling by hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

Clear Water Lines

n Run water through both faucets and inlet hoses, into a laundry

tub, drainpipe, or bucket, to get rid of particles in the water lines that might clog the inlet valve screens.

n Check the temperature of the water to make sure that the hot

water hose is connected to the hot water faucet and that the cold water hose is connected to the cold water faucet.

3. Using pliers, tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten. Damage to the valve can result.

4. Turn on the water faucets completely and check for leaks.

NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

INSTALLING STACKED WASHER/DRYER

Route Drain Hose

Proper routing of the drain hose avoids damage to your ﬂoor due to water leakage. Read and follow these instructions.

Remove drain hose from the washer drum

1. Using locking pliers, squeeze hose clamp tabs together and

insert over the end of the drain hose.

2. Slide the drain hose onto the washer connection.

3. Once the drain hose is in place, release the pliers.

4. The washer drain system can be installed using a ﬂoor drain,

wall standpipe, ﬂoor standpipe, or laundry tub.

Laundry tub drain or standpipe drain

Connect the drain hose form to the corrugated drain hose. Snap either end of the drain hose form to the drain

hose at the point where the corrugation begins.

Secure Drain Hose

1. Drape the power cord over the washer top.

2. Move the washer to its ﬁnal location.

3. Place the drain hose

in the laundry tub or standpipe as shown.

4. Secure the drain hose using the supplied beaded tie strap.

Bend drain hose over drain hose form and snap into place.

NOTE: Hose must not extend more than 25 mm (1") past the end of the U bend.

To keep drain water from going back into the washer:

n Do not straighten the drain hose, do not force excess drain

hose into standpipe. Hose should be secure, but loose enough to provide a gap for air.

n Do not lay excess hose on the bottom of the laundry tub.

Floor drain

You may need additional parts. See “Alternate Parts.”

5. If the washer faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe as shown.

NOTES:

n Do not force excess drain hose

back into the rear of the washer.

n To avoid siphoning, do not seal the

drain hose into the standpipe.

WASHER DRAIN SYSTEM

The washer can be installed using the standpipe drain system (ﬂoor or wall), the laundry tub drain system, or the ﬂoor drain system.

Standpipe drain system – wall or ﬂoor

The standpipe drain requires a minimum diameter standpipe of 50 mm (2"). The minimum carry-away capacity can be no less than 38 L (10 gal.) per minute.

Wall

The top of the standpipe must be at least 762 mm (30") high and no higher than 2.4 m (96") from the bottom of the washer.

Floor

Laundry tub drain system

The laundry tub needs a minimum 76 L (20 gal.) capacity. The top of the laundry tub must be at least 762 mm (30") above the ﬂoor.

Floor drain system

The ﬂoor drain system requires a siphon break that may be purchased separately.

The siphon break (Part Number 285834) must be a minimum of 710 mm (28") from the bottom of the washer. Additional hoses might be needed.

SyphonBreak

LEVELING

Leveling Stacked Washer/Dryer

Leveling your washer/dryer properly reduces excess noise and vibration.

1. Remove cardboard from beneath washer/dryer. Place a level on top edges of washer/dryer, checking each side and front. If not level, tip washer/dryer and adjust feet up or down as shown in Steps 3 and 4, repeating as necessary.

3. If washer/dryer is not level, use a 14 mm or 9/16" openend or adjustable wrench to turn jam nuts clockwise (as viewed from above) on feet until they are about 13 mm (1/2") from the washer/dryer cabinet. Then turn the leveling foot counterclockwise to lower the washer/dryer or clockwise to raise the washer/dryer. Recheck levelness of washer/dryer and that all four feet are ﬁrmly in contact with the ﬂoor. Repeat as needed.

HELPFUL TIP: You may want to prop up front of washer/dryer about 102 mm (4") with a wood block or similar object that will support weight of washer/dryer.

Jam nut

4. When washer/dryer is level and all four feet are ﬁrmly in contact with the ﬂoor, use a 14 mm or 9/16" open-end or adjustable wrench to turn jam nuts counterclockwise (as viewed from above) on leveling feet tightly against washer/dryer cabinet.

HELPFUL TIP: You may want to prop washer/dryer with wooden block.

Not Level

2. Grip washer/dryer from top and rock back and forth, making sure all four feet are ﬁrmly on ﬂoor. Repeat, rocking washer/dryer from side to side. If washer/dryer rocks, go to Step 3 and adjust leveling feet. If all four feet are in ﬁrm contact with ﬂoor, go to Step 4.

LEVEL

Not Level

COMPLETE INSTALLATION

1. Check the electrical requirements. Be sure that you have the

correct electrical supply and the recommended grounding method. See “Electrical Requirements.”

2. Check that all parts are now installed. If there is an extra part,

go back through the steps.

3. Check that you have all of your tools.

4. Dispose of/recycle all packaging materials.

5. Check that the water faucets are on.

6. Check for leaks around faucets and inlet hoses.

WARNING

Electric Shock Hazard

This washer/dryer must be earthed.

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or electric shock.

8. To test and to clean your washer, measure 1/2 the detergent manufacturer’s recommended amount of High Efﬁciency (HE) detergent for a medium-size load. Pour the detergent into the detergent dispenser. Select any cycle and allow the washer to complete one whole cycle.

9. Check dryer operation. Using a full heat cycle, let the dryer run for at least ﬁve minutes. Dryer will stop when time is used up.

NOTE: Dryer door must be closed for dryer to operate. When door is open, dryer stops, but timer continues to run. To restart dryer, close door and push cycle button.

If the burner does not ignite and you can feel no heat inside the dryer, shut off dryer for ﬁve minutes. Check that all supply valve controls are in “ON” position and that the electrical cord is plugged in. Repeat ﬁve-minute test.

7. Plug into a grounded outlet, or connect power.

REVERSING DRYER DOOR SWING

NOTE: Dryer only. Washer door is not reversible.

Remove the Door Assembly

1. Place a towel or soft cloth on top of dryer or work space to avoid

scratching of the surface.

2. Remove 3 of the 4 screws that hold the door hinge on the front panel of the dryer. Partially loosen the remaining screw with keyhole opening and lift the door off the screw.

4. Lift the inner door assembly off outer door assembly.

5. Rotate outer door 180°.

3. Lay the door assembly on a previously prepared ﬂat surface

with the inside (inner door assembly) facing up, and remove 6 phillips-head screws to release outer door assembly from inner door assembly.

NOTE: It is important that you remove only 6 indicated screws.

Reverse Hinge

1. Use a small ﬂat-blade screwdriver to remove 2 plug strips from

the inner door. Slide the head of the screwdriver under the plugs, without scratching inner door surface, and lift up strip.

2. Remove the 4 screws that attach to inner door hinge.

REVERSING DRYER DOOR SWING

3. Move hinge to other side. Reinstall 4 screws.

4. Reinstall plug strips on opposite side of the inner door.

Reverse the strike

1. Use a small ﬂat-blade screwdriver to remove plug strip from the

dryer door opening. Slide the head of the screwdriver under the plugs, without scratching dryer surface, and lift up strip.

2. Remove the strike using a Phillips screwdriver.

5. Check for ﬁngerprints on the glass. Clean if necessary.

Replace the Door Assembly

1. Place the inner door assembly inside the outer door assembly.

2. Reassemble the inner and outer door assemblies with the

6 screws.

3. Insert strike on the opposite side.

Reinstall the door

1. Partially insert the third screw from the top; then slide the

hinge onto this screw while hooking the hinge into the front panel hole. Reattach door to dryer front panel with the remaining three screws.

2. Check for ﬁngerprints on the glass. Clean if necessary.

3. Close door and check that it latches securely.

STACKED WASHER/DRYER MAINTENANCE INSTRUCTIONS

Washer

Cleaning the Door Seal/Bellow

1. Open the washer door and remove any clothing or items from

the washer.

2. Inspect inner glass door. If debris is present, wipe it off using a damp cloth.

3. Inspect the colored seal/bellow between the door opening and the basket for stained areas. Pull back the seal/bellow to inspect all areas under the seal/bellow and to check for foreign objects.

Seal/Bellow

4. If stained areas are found, wipe down these areas of the seal/

bellow:

a) Mix a dilute solution, using 177 mL (3/4 cup) of liquid chlorine

bleach, and 3.8 L (1 gal.) of warm tap water.

b) Wipe the seal/bellow area with the dilute solution, using

a damp cloth. c) Let stand 5 minutes. d) Wipe down area thoroughly with a dry cloth and let the

washer interior air dry with door open.

IMPORTANT:

n Wear rubber gloves when cleaning for prolonged periods. n Refer to the bleach manufacturer’s instructions for proper use.

Maintenance Instructions:

This washer has a special cycle that uses higher water volumes in combination with liquid chlorine bleach to thoroughly clean the inside of the washer.

NOTES:

n Read these instructions completely before beginning the

cleaning process.

n If necessary, the cleaning cycle may be interrupted by pressing

the lower-right (QUICK CYCLE) button twice. However, this will not immediately stop the cycle. The washer will continue with several rinse and drain steps to ensure that all remaining bleach is rinsed from the washer.

To clean washer interior:

1. Open the washer door and remove any clothing or items from

the washer.

2. Use liquid chlorine bleach: Open the dispenser drawer and immediately add 160 mL (2/3 cup) of liquid chlorine bleach to the bleach compartment.

NOTE: Do not add any detergent. Use of more than 160 mL

(2/3 cup) of bleach will cause product damage over time.

3. Close the washer door and the dispenser drawer.

4. To start the Washer Cleanout cycle, ﬁrst enter “Service Mode.”

Then press and hold the lower-right (QUICK CYCLE) button for 2 seconds. With the entire display ﬂashing, press the centerright (BRIGHTS) button.

To exit out of the service mode and activate the clean wash cycle, push the BRIGHTS button, then turn the key.

NOTE: The door will lock, the basket will rotate 1/2 turn, then

the door will unlock and lock again, then the Washer Cleanout Cycle will continue.

n The washer will not ﬁll, but the basket will rotate while

the washer runs a short sensing cycle. This will take approximately 3 minutes.

5. The cycle will determine whether clothing or other items are in the washer.

a) If no items are detected in the washer, it will proceed to

Step 7.

b) If any items are detected in the washer, “F-34” will be

displayed. Then the door will unlock.

n Enter the service mode and then press and hold the

lower-right (QUICK CYCLE) button to cancel the failure code. Then repeat steps 1, 3, and 4 to start the cycle again.

6. Once the cycle has begun, allow the cycle to complete.

7. After the cycle is complete, leave the door open slightly to allow

for better ventilation and drying of washer interior.

STACKED WASHER/DRYER MAINTENANCE INSTRUCTIONS

Washer

Always do the following to maintain washer freshness:

n Use only HE High Efﬁciency detergent. n Leave the door slightly open after each cycle to allow for better

ventilation and drying of washer interior.

n Clean the washer monthly using the Washer Maintenance

Procedure, using 160 mL (2/3 cup) of liquid chlorine bleach.

n If the procedure does not sufﬁciently improve the washer

freshness, please evaluate your installation and usage conditions for other causes.

Cleaning the exterior

Use a soft damp cloth or sponge to wipe up any spills. Occasionally wipe the outside of your washer to keep it looking new. Use mild soap and water. Do not use abrasive products.

Cleaning the dispenser drawer

The dispenser drawer is removable for easy cleaning.

1. Unlock the dispenser drawer for removal by inserting a ﬂat-blade screwdriver into the catch release. Remove the dispenser drawer.

2. Remove the inserts (the siphon from the softener and bleach compartments).

3. Wash the parts under running water. NOTE: Do not wash components in the dishwasher.

4. Replace the inserts and return the dispenser to the drawer.

Water inlet hoses

Replace the inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, record the date of replacement.

Dryer

Maintenance instructions:

• Clean lint screen before and after each cycle.

• Removing accumulated lint:

From inside the dryer cabinet: Lint should be removed every 2 years or more often,

depending on dryer usage. Cleaning should be done

by a qualiﬁed person. From the exhaust vent: Lint should be removed every 2 years, or more often,

depending on dryer usage.

• Keep area around dryer clear and free from combustible

materials, gasoline and other ﬂammable vapors and liquids.

• Keep dryer area clear and free from items that would obstruct

the ﬂow of combustion and ventilation air.

If dryer does not operate, check the following:

• Electrical supply is connected.

• Circuit breaker is not tripped or house fuse is not blown.

• Door is closed. Listen closely to hear the door switch activate.

• Cycle selection button has been pushed rmly.

• For gas dryers, check that gas supply shut-off valves are set in

open position.

If you need help, contact the dealer from whom you purchased the appliance, or a Maytag designated service company. When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request.

IF YOU NEED ASSISTANCE

Accessories

Enhance your washer/dryer with these premium accessories. For more high-quality items or to order, contact your authorized

Maytag distributor.

Part Number Accessory 8212526 31682 1903WH

Whirlpool Corporation, Benton Harbor, Michigan 49022, U.S.A.

Manufacturer site: Whirlpool Mexico S.A. de C.V.,

Antigua Carretera a Roma Km 9, Col.

El Milagro, Apodaca, Nuevo Leon, C.P. 66634, Mexico.

EU representative: Maytag UK Ltd, Redhill, RH1 1AX, UK

BAUKNECHT HAUSERGRÄTE Gmb H, D-73614 Schorndorf

Washer drip trays; ﬁts under all All-purpose appliance cleaner Laundry supply storage cart

TECHNICAL SPECIFICATIONS – GAS DRYER

ELECTRONIC CONTROL SETUP INSTRUCTIONS

WHITES

PERM.

PRESS

COLORS

DELICATES AND KNITS

BRIGHTS

QUICK

CYCLE

WASHER

Washer Control

NOTE: After the washer/dryer has been installed and plugged

in, the display will show “0 MINUTES” on the washer and dryer portions of the display. After the washer and dryer doors have been opened and closed, the display will show the price for each machine. On washer/dryers set for free cycles, the display sections will ﬂash “SELECT CYCLE.”

1. PD Models: Insert coins until “SELECT CYCLE” ﬂashes on the display portion of the washer or dryer that is to be run.

PN Models: A debit card is required rather than coins.

Generation 1 or 2 debit card systems may be used; but when the Generation 2 debit system is used, the controls will automatically be set to Enhanced Debit mode (J. Ed). In Enhanced Debit mode, the card balance will also display when a debit card is inserted into the reader.

2. Door must be closed on the desired washer/dryer before cycle selection is made.

3. Press the fabric setting button for the washer/dryer cycle desired. After the cycle is started, the time will display and count down.

4. If a cycle is interrupted by opening the door or power loss, “RESELECT CYCLE” will ﬂash in the display. To restart the washer/dryer, close door and reselect desired cycle.

NOTE: When set for free vend operation an ongoing dryer cycle will cancel if the door is opened.

DRYER

WHITES

& COLORS

PERM.

PRESS

Dryer Control

DELICATES

General Washer/Dryer User Information

SCROLLING “OUT OF ORDER” MESSAGE, FOLLOWED BY A FAILURE OR DIAGNOSTIC CODE, SHOWING IN DISPLAY –

condition indicates the washer/dryer is inoperative. Diagnostic codes being displayed on the upper portion of the display pertain to the dryer section, and diagnostic codes displayed on the lower portion of the display apply to the washer section. Diagnostic codes displayed on both the upper and lower portions of the display pertain to the control system of both the washer and dryer.

“0 MINUTES” SHOWING IN DISPLAY – This indicates the cycle is complete and the washer/dryer cannot be operated. Coins dropped or debit inputs during this condition will be stored in escrow but cannot be used until normal operation is restored by opening and closing the door. If a door switch has failed, causing “0 MINUTES” to remain in the display after the door is opened and closed, it must be replaced before normal operation can be restored.

COLD START (Initial ﬁrst use) – Washer/dryer is programmed at the factory as follows:

Washer 11-minute wash period

1.75 wash price (PD models)

0.00 wash price (PN models) 3 rinses (extra rinse not enabled) Dryer 5 minutes per coin for PD models 45 minutes dry time for PN models

1.50 dry price (ﬁxed cycle with top off – PD Models)

0.00 dry price (ﬁxed cycle – PN Models)

This

ELECTRONIC CONTROL SETUP INSTRUCTIONS

WARM START (after power failure) – A few seconds after power is restored, if a cycle was in progress at the time of the power failure, “RESELECT CYCLE” will ﬂash in the display, indicating the need for a key press to restart washer or dryer.

WASHER DOOR LOCK – Prior to beginning a cycle, there is a door lock routine of lock/unlock/relock, then cycle begins. The door will remain locked until the end of a cycle or approximately 2 minutes after a power interruption.

PRICING – After the door is opened and then closed following the completion of a cycle, the display indicates the cycle price (unless set for free operation, where the display will ﬂash “SELECT CYCLE”). As coins are dropped or debit inputs arrive, the display will change to lead the user through the initiation of a cycle.

There are four (4) types of dryer pricing: Fixed “Vend” Pricing

A dryer setup for “Fixed Cycle” operation can only accept additional time accumulated by increments equal to the length of a complete dry cycle. A maximum of 99 minutes may be purchased; no additional credit is given for coins dropped with 99 minutes in the display.

Accumulator Pricing

If the price is set to one coin 1, then accumulator pricing is in effect. Cycle time can be purchased one coin at a time (PD models) up to the maximum time of 99 minutes.

Fixed Cycle With Top Off Pricing

A dryer set to offer “Top Off” capability will allow time to be added to an existing dry cycle in increments equal to the number of minutes of dry time per coin (coin 1), up to 99 minutes, regardless of the cost required to start the dryer. No credit is given for coins or debit inputs entered when the control is displaying 99 minutes.

PN Models: In Enhanced Debit Mode, the top off price can be set independently (see VALUE OF COIN 2), and the top off time is calculated according to the following equation:

top off time = x full cycle length

top off price

full cycle price

Penny increment offset is not applied to top off purchases. FREE CYCLES – This is established by setting the cycle price

to zero. When this happens, “SELECT CYCLE” will appear rather than a cycle price. Any cycle started as a free cycle will automatically terminate when the door is opened.

DEBIT CARD READY – This washer/dryer is debit card ready. It will accept a variety of debit card systems, but does NOT come with a debit card reader. Refer to the debit card reader manufacturer for proper washer/dryer setup. In models converted to a Generation 1 debit card system, debit pulses represent the equivalent of one coin (coin 1).

Control Set-up Procedures

IMPORTANT: Read all instructions before operating. PD/PN Models: Insert service switch key and turn

counterclockwise. PN Models: Once a Generation 2 debit card reader is installed

(according to the reader manufacturer’s instructions), the set-up modes can only be changed by inserting a set-up card (supplied by the reader manufacturer) into the card slot. Inserting the service switch key and turning will only allow access to the service mode.

The washer/dryer is now in the set-up mode. The lower fabric setting buttons and the lower portion of the display are used to set up the digital control for the washer. The upper three fabric setting buttons and the upper portion of the display are used to set up the controls for the dryer.

The display can contain 4 numbers and/or letters and a decimal point on both the top and bottom display portions. These are used to indicate the set-up codes and related code values available for use in programming the washer/dryer.

How to Use the Buttons to Program the Controls

1. The lower-left (PERM. PRESS) button is used to adjust the

values associated with washer set-up codes and the upper-left (WHITES & COLORS) button is for the dryer. Pressing the button will change the value by increments. Rapid adjustment is possible by holding the button down.

2. The lower-middle (DELICATES AND KNITS) button will advance through the set-up codes. Pressing the button will advance both the washer and dryer to the next available set-up code. Some set-up codes are washer- or dryer-speciﬁc and will not be displayed on both the washer and dryer portions of the display. Holding down the lower-middle (DELICATES AND KNITS) button will automatically advance through the set-up codes at a rate faster than 1 per second.

3. The lower-right (QUICK CYCLE) button is used to select or deselect washer options; upper-right (DELICATES) is used for dryer option selection or deselection.

+ 110 hidden pages

Maytag MLE20PNAGW, MLE20PNBGW, MLG20PDBGW, MLE20PNCGW, MLE20PDCGW Installation Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual