Maytag MIM1554ZRS User Manual

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

ICE MAKER

USER INSTRUCTIONS

W10520283C

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

please visit our website at www.maytag.com for additional information. If you still need assistance, call us at 1-800-688-9900. In Canada, visit our website at www.maytag.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the ice maker compartment.

Table of Contents / Índice / Table des matières

ICE MAKER SAFETY............................... 1

INSTALLATION INSTRUCTIONS........... 2

ICE MAKER USE ................................... 11

ICE MAKER CARE................................. 13

TROUBLESHOOTING ........................... 16

PERFORMANCE DATA SHEET............ 19

WARRANTY ........................................... 20

ICE MAKER SAFETY

SEGURIDAD DE LA

FÁBRICA DE HIELO.............................. 21

INSTRUCCIONES

DE INSTALACIÓN ................................. 22

USO DE LA FÁBRICA DE HIELO ......... 32

CUIDADO DE LA FÁBRICA

DE HIELO ............................................... 34

SOLUCIÓN DE PROBLEMAS............... 37

HOJA DE DATOS DEL

RENDIMIENTO ...................................... 40

GARANTÍA ............................................. 41

SÉCURITÉ DE LA MACHINE

À GLAÇONS........................................... 43

INSTRUCTIONS D’INSTALLATION ..... 44

UTILISATION DE LA

MACHINE À GLAÇONS ........................ 54

ENTRETIEN DE LA

MACHINE À GLAÇONS ........................ 55

DÉPANNAGE ......................................... 59

FEUILLE DE DONNÉES SUR

LA PERFORMANCE.............................. 62

GARANTIE.............................................. 63

INSTALLATION INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING

: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic

precautions

SAVE THESE INSTRUCTIONS

■

Plug into a grounded 3 prong outlet.

■

Do not remove ground prong.

■

Do not use an adapter.

■

Do not use an extension cord.

■

Disconnect power before manually cleaning the inside components.

■

Disconnect power before servicing.

■

Replace all parts and panels before operating.

■

Use two or more people to move and install ice maker.

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer. WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

WARNING

Excessive Weight Hazard Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

Unpack the Ice Maker

Removing Packaging Materials

Remove tape and glue from your ice maker before using.

■ To remove any remaining tape or glue from the exterior of the

ice maker, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

■ Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. Do not use chlorine bleach on the stainless steel surfaces of the ice maker. These products can damage the surface of your ice maker.

Cleaning Before Use

After you remove all of the packaging materials, clean the inside of your ice maker before using it. See the cleaning instructions in the “Ice Maker Care” section.

Location Requirements

■ To ensure proper ventilation for your ice maker, the front side

must be completely unobstructed. The ice maker may be closed-in on the top and three sides, but the installation should allow the ice maker to be pulled forward for servicing if necessary.

■ Installation of the ice maker requires a cold water supply inlet

of ¹⁄₄" (6.35 mm) OD soft copper tubing with a shutoff valve or a Whirlpool supply line Part Number 8212547RB, and a Whirlpool approved drain pump, Part Number 1901A, only to carry the water to an existing drain.

■ Choose a well ventilated area with temperatures above 55°F

(13°C) and below 110°F (43°C). Best results are obtained between 70°F and 90°F (21ºC and 32°C).

■ The ice maker must be installed in an area sheltered from the

elements, such as wind, rain, water spray, or drip.

■ When installing the ice maker under a counter, follow the

recommended opening dimensions shown. Place electrical and plumbing fixtures in the recommended location as shown.

NOTES:

■ Check that the power supply cord is not damaged, or

pinched or kinked between the ice maker and the cabinet.

■ Check that the water supply line is not damaged, or

pinched or kinked between the ice maker and the cabinet.

■ Check that the drain line (on some models) is not

damaged, or pinched or kinked between the ice maker and the cabinet.

■ Check that the ice maker door is not flush with the

3¹⁄₂" (8.9 cm)

9" (22.9 cm)

11¹⁄₂"

(29.2 cm)

24"

(60.1 cm)

15"

(38.1 cm)

34"

(86.4 cm)

Min.

¹⁄₂"

(87.6 cm)

Max.

28¹⁄₂"

(72.4 cm)

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

standard cabinets to avoid problems with opening the ice maker door.

A. Recommended location for electrical and plumbing fixtures B. Floor level

■ Choose a location where the floor is even. It is important for

the ice maker to be level in order to work properly. If needed, you can adjust the height of the ice maker by changing the height of the leveling legs. See “Leveling.”

Electrical Requirements

Before you move your ice maker into its final location, it is important to make sure you have the proper electrical connection:

A 115 volt, 60 Hz., AC only, 15- or 20-amp electrical supply,

Code and local codes and ordinances, is required. It is recommended that a separate circuit, serving only your ice

maker, be provided. Use a receptacle which cannot be turned off by a switch or pull chain.

properly grounded in accordance with the National Electrical

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) equipped outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Ice quality may be affected. If nuisance tripping has occurred, and if the condition of the ice appears poor, dispose of it.

Recommended Grounding Method

The ice maker must be grounded. The ice maker is equipped with a power supply cord having a 3 prong grounding plug. The cord must be plugged into a mating, 3 prong, grounding-type wall receptacle, grounded in accordance with the National Electrical Code and local codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility of the customer to have a properly grounded, 3 prong wall receptacle installed by a qualified electrician.

Water Supply Requirements

Check that the water supply lines are insulated against freezing conditions. Ice formations in the supply lines can increase water pressure and damage your ice maker or home. Damage from frozen supply lines is not covered by the warranty.

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT:

■ A reverse osmosis water filtration system is not

recommended for ice makers that have a drain pump installed.

■ For gravity drain systems only.

■ The pressure of the water supply coming out of a reverse

osmosis system going to the water inlet valve of the ice maker needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

NOTE: The reverse osmosis system must provide 1 gal. (3.8 L) of water per hour to the ice maker for proper ice maker operation. If a reverse osmosis system is desired, only a whole-house capacity reverse osmosis system, capable of maintaining the steady water supply required by the ice maker, is recommended. Faucet capacity reverse osmosis systems are not able to maintain the steady water supply required by the ice maker.

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If you have questions about your water pressure, call a licensed, qualified plumber.

Vacation or Extended Time

■ When you will not be using the ice maker during the summer

months, turn off the water and power supply to the ice maker.

■ Check that the water supply lines are insulated against

freezing conditions. Ice formations in the supply lines can increase water pressure and cause damage to your ice maker or home. Damage from freezing is not covered by the warranty.

Without Use

Connect Water Supply

A B

DA B C

Read all directions before you begin.

IMPORTANT:

■ Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and ordinances.

■ Use copper tubing or Whirlpool supply line, Part Number

8212547RP, and check for leaks.

■ Install tubing only in areas where temperatures will remain

above freezing.

Tools Needed

Gather the required tools and parts before starting installation:

■ Flat-blade screwdriver

■ ⁷⁄₁₆" and ¹⁄₂" open-end wrenches or two adjustable wrenches

■ ¹⁄₄" nut driver

NOTE: Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

Connecting the Water Line

1. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

2. Using a ¹⁄₂" copper supply line with a quarter-turn shutoff

valve or the equivalent, connect the ice maker as shown. NOTE: To allow sufficient water flow to the ice maker a

minimum ¹⁄₂" diameter home supply line is recommended.

4. Place the free end of the tubing into a container or sink, and

turn on main water supply and flush out tubing until water is clear. Turn off shutoff valve on the water pipe.

IMPORTANT: Always drain the water line before making the final connection to the inlet of the water valve to avoid possible water valve malfunction.

5. Bend the copper tubing to meet the water line inlet which is

located on the back of the ice maker cabinet as shown. Leave a coil of copper tubing to allow the ice maker to be pulled out of the cabinet or away from the wall for service.

Rear View

A. Copper tubing B. Water supply tube clamp

6. Remove and discard the short, black plastic tube from the

end of the water line inlet.

7. Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet’s side wall or other parts inside the cabinet.

C. Inlet water tube clamp and

supply line connector

A. Bulb B. Nut

3. Now you are ready to connect the copper tubing. Use ¹⁄₄"

(6.35 mm) OD soft copper tubing for the cold water supply.

■ Ensure that you have the proper length needed for the

job. Be sure both ends of the copper tubing are cut square.

■ Slip compression sleeve and compression nut on copper

tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

A. Compression sleeve

B. Compression nut

C. Copper tubing

A. Line to ice maker B. Nut (purchased)

C. Ferrule (purchased) D. Supplied line from ice maker

8. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

9. Turn shutoff valve ON.

10. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Drain Pump Installation

(on some models)

NOTE: Connect drain pump to your drain in accordance with all state and local codes and ordinances. It may be desirable to insulate drain tube thoroughly up to drain inlet to minimize condensation on the drain tube. Insulated tube kit Part Number W10365792 is available for purchase. Drain pump is designed to pump water to a maximum height of 10 ft (3 m). Use only Whirlpool approved drain pump kit Part Number 1901A. Do not connect the outlet end of the drain tube to a closed pipe system to keep drain water from backing up into the ice maker.

Kit Contains:

WARNING

Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

C D

■ Drain pump kit Part Number 1901A

■ ⁵⁄₈" ID x 5¹⁄₈" drain tube (ice maker bin to drain pump reservoir

inlet)

■ ¹⁄₂" ID x 10 ft (3 m) drain tube hose (drain pump discharge to

household drain)

■ ⁵⁄₁₆" ID x 32" (81 cm) vent tube (drain pump reservoir vent to

ice maker cabinet back)

■ Cable clamps (secures vent tube to back of ice maker) (3)

■ #8-32 x ³⁄₈" pump mounting screws (secures drain pump to

baseplate and clamps to back of ice maker) (5)

■ ⁵⁄₈" small adjustable hose clamp (secures vent to drain pump)

■ ⁷⁄₈" large adjustable hose clamp, (secures drain tube to ice

maker bin and drain pump reservoir inlet) (3)

■ Rear panel (2)

■ Instruction sheet

If Ice Maker Is Currently Installed

5. If ice maker is built into cabinets, pull ice maker out of the

opening.

6. Disconnect water supply line. See “Water Supply Line”

illustration.

Water Supply Line

NOTE: If ice maker is not installed, please proceed to “Drain

Pump Installation” section.

1. Push the selector switch to the Off position.

2. Unplug ice maker or disconnect power.

3. Turn off water supply. Wait 5 to 10 minutes for the ice to fall

into the storage bin. Remove all ice from bin.

4. Unscrew the drain cap from the bottom of the water pan

located inside the storage bin. Allow water to drain completely. Replace drain cap. See “Drain Cap” illustration.

Drain Cap

¹⁄₄

" copper tubing B. Cable clamp C.

¹⁄₄

" compression nut

D. Ferrule (sleeve)

E. Ice maker connection

Drain Pump Installation

NOTE: Do not kink, smash or damage tubes or wires during

installation.

1. Unplug ice maker or disconnect power.

2. Remove rear panel. See “Rear Panel” illustration for 5 screw

locations. Pull rear panel away from the drain tube and discard.

Rear Panel

A. Drain cap

A. Screw locations

3. Remove the old drain tube and clamp attached to the ice

maker bin.

NOTE: Discard old drain tube and clamp.

4. Install new drain tube (⁵⁄₈" ID x 5¹⁄₈") from ice maker bin to

drain pump reservoir inlet using new adjustable clamps. See “Drain Tube” illustration.

NOTES:

■ Do not kink.

■ Trim tube length, if required.

Drain Tube

A B

C D

⁷⁄₈

" adjustable hose clamp

B. Drain tube (ice bin to drain pump)

⁷⁄₈

" adjustable hose clamp

D. Drain pump reservoir inlet

5. Install vent tube (⁵⁄₁₆" ID x 32" [81 cm]) to drain pump reservoir

vent. Use one ⁵⁄₈" small adjustable clamp, supplied. See “Parts Locations” illustration.

NOTE: Do not install household drain tube at this time.

Parts Locations

Drain Pump Mounting Tab Slot

A. Mounting tab slot

Drain Pump Installed

A. Vent tube B.

⁵⁄₈

" hose clamp C. Drain pump discharge tube D. Drain pump

E. Ice maker unit power cord F. #8-32 x

G. Drain pump power cord, clamp

and screw

³⁄₈

" pump mounting screws

6. Remove power cord clamp and ground screw attached to ice

maker power cord, which is mounted to the unit base. See “Parts Locations” illustration.

NOTE: Clamp and screw will be reused.

7. Slide drain pump into the ice maker base on the right side.

The pump mounting tab should slip into the rectangular slot in the ice maker base. It will be necessary to tip the pump slightly to slip into the slot. See “Drain Pump Mounting Tab Slot” illustration.

A. Drain pump installed

8. Align the 2 screw holes at the rear of the pump. Use two

#8-32 x ³⁄₈" screws, supplied. See “Parts Locations” illustration.

9. Connect drain tube to ice maker bin outlet (⁵⁄₈" ID), using ⁷⁄₈"

adjustable clamp, supplied. See “Drain Tube” illustration.

10. Coil ice maker power cord into a 4" (10.2 cm) diameter coil.

Wrap electrical tape around the power cord in several places to keep the cord in a coil. Locate coiled power cord between the drain pump and side of enclosure and plug into the receptacle of the drain pump. See “Parts Locations” illustration.

11. Attach the drain pump power cord to ice maker unit base with

clamp and screw (removed in Step 6) that was used to attach ice maker power cord. See “Parts Locations” illustration.

12. Place new rear panel (small one for 15" ice makers, large one

for 18") against the back of the ice maker. Route the vent tube and drain pump discharge tube through cutouts in the rear panel.

13. Secure rear panel with original screws. See “Rear Panel”

illustration.

14. Secure vent tube to back of ice maker using 3 clamps and

three #8-32 x ³⁄₈" screws, supplied. See “Vent Tube” illustration.

Vent Tube

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

1⁷⁄₈" (4.8 cm)

23"

(58.4 cm)

2" - 1¹⁄₂"

(5 cm - 3.8 cm)

1" (2.54 cm)

NOTE: Do not pinch, kink or damage the vent tube. Check that it is not damaged, or pinched or kinked between the cabinet and the ice maker.

A. Vent tube B. Clamps and screws

15. Attach ¹⁄₂" ID x 10 ft (3 m) drain tube to pump discharge tube.

See “Parts Locations” illustration.

16. Connect ice maker to water supply and install ice maker as

specified by the product installation instructions.

17. Check all connections for leaks.

■ Drain lines must have a minimum of ⁵⁄₈" (15.88 mm) inside

diameter.

■ Drain lines must have a 1" drop per 48" (2.54 cm drop per

122 cm) of run or ¹⁄₄" drop per 12" (6.35 mm per 30.48 cm) of run and must not have low points where water can settle.

■ The floor drains must be large enough to accommodate

drainage from all drains.

■ The ideal installation has a standpipe with a 1¹⁄₂" (3.81 cm) to

2" (5.08 cm) PVC drain reducer installed directly below the outlet of the drain tube as shown. You must maintain a 1" (2.54 cm) air gap between the drain hose and the standpipe.

■ Do not connect the outlet end of the drain tube to a closed

pipe system to keep drain water from backing up into the ice maker.

IMPORTANT: A drain pump is necessary when a floor drain is not available. A Drain Pump kit, Part Number 1901A, is available for purchase.

Side View

18. Plug in ice maker or reconnect power.

19. Tu r n on ice mak e r.

20. Wait for rinsing cycle, approximately 5 minutes, to be sure the

ice maker is operating properly.

Drain Connection

Gravity Drain System

Connect the ice maker drain to your drain in accordance with all state and local codes and ordinances. If the ice maker is provided with a gravity drain system, follow these guidelines when installing drain lines. This will help keep water from flowing back into the ice maker storage bin and potentially flowing onto the floor, causing water damage.

A. Drain hose B. 1" (2.54 cm) air gap C. PVC drain reducer

D. Center of drain should be 23" (58.4 cm) from

front of door, with or without the panel on the door. The drain should also be centered from left to right (7 from either side of the ice maker).

³⁄₄

" (1.91 cm)

⁵⁄₁₆

" [18.56 cm]

Drain Pump System (on some models)

IMPORTANT:

■ Connect the ice maker drain to your drain in accordance with

the International Plumbing Code and any local codes and ordinances.

■ The drain pump discharge line must terminate at an open

sited drain.

■ Maximum rise 10 ft (3.1 m)

■ Maximum run 100 ft (30.5 m)

NOTES:

■ If the drain hose becomes twisted and water cannot drain,

your ice maker will not work.

■ It may be desirable to insulate the drain line thoroughly up to

the drain inlet. An Insulation Sleeve kit, Part Number W10365792, is available for purchase.

■ Do not connect the outlet end of the drain tube to a closed

pipe system to keep drain water from backing up into the ice maker.

Connecting the Drain

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Excessive Weight Hazard Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

WARNING

Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

After ensuring that the drain system is adequate, follow these steps to properly place the ice maker:

1. Plug into a grounded 3 prong outlet.

Remove Stainless Steel Door Wrap Panel— On Some Models

A. Hex-head screws

1. Remove the 2 hex-head screws located under the stainless

steel door wrap panel flange on the bottom of the door.

2. Pull up and outward on the door wrap panel from the bottom.

3. Rotate the door wrap panel until it separates from the door

and pull up. NOTE: Be sure the edge guards do not separate from the

door wrap panel.

2. Style 1—For gravity drain system, push the ice maker into

position so that the ice maker drain tube is positioned over the PVC drain reducer. See “Gravity Drain System.”

Style 2—For drain pump system connect the drain pump outlet hose to the drain. See “Drain Pump System.”

3. Recheck the ice maker to be sure that it is level. See

“Leveling.”

4. If it is required by your local sanitation code, seal the cabinet

to the floor with an approved caulking compound after all water and electrical connections have been made.

Door Reversal—Side Swing Only

Tools Needed

Gather the required tools and parts before starting installation.

■ ⁵⁄₁₆" wrench ■ Flat putty knife

■ ¹⁄₄" wrench ■ Phillips screwdriver

Hinge pin

⁵⁄₁₆

" hex-head hinge screw

Door Stop and End-Cap Reversal

1. Unplug the ice maker or disconnect power.

2. Remove the handle screws and handle (on some models).

3. Remove the hinge pin from the top hinge.

4. Remove the door from the hinges and replace the top hinge

pin.

5. Remove the screw and door stop at corner A. Remove the

screw and end cap at corner C. Place the door stop at corner C, and tighten screw. Place the end cap at corner A, and tighten screw.

Handle screw End cap screw

6. Remove the screw and door stop at corner D. Remove the

screw and end cap at corner B. Place the door stop at corner B, and tighten screw. Place the end cap at corner D, and tighten screw.

Top Hi nge

C D

A. Top corner open (no end cap) B. Beginning top corner end cap

C. Beginning bottom corner end cap D. Bottom corner open (no end cap)

7. Depending on your model, the brand badge for the front door

of your ice maker may be in the package with the Use and Care Guide. Fasten the brand badge to the door.

8. Set the door aside.

Reverse Hinges

1. Unscrew and remove the top hinge. Replace the screws in

the empty hinge holes.

2. Remove the screws from the bottom of the opposite side of

the ice maker cabinet. Turn the top hinge upside down so that the hinge pin points up. Place the hinge on the bottom opposite side of the ice maker and tighten screws.

3. Remove the “old” bottom hinge screws and hinge. Replace

the screws in the empty hinge holes.

4. Remove the screws from the top of the opposite side of the

ice maker cabinet. Turn the hinge upside down so that the hinge pin points down. Place the hinge on the top opposite side of the ice maker and tighten the screws.

5. Remove the top hinge pin.

A. Hinge pin

B. Phillips-head countersink screw

C. Hinge pin sleeve

Bottom Hinge

A. Hex-head hinge screw B. Hinge pin sleeve C. Phillips-head countersink screw

Reverse Door Catch

D. Hinge

E. Hex-head hinge screw

D. Hinge pin

E. Hinge

Replace Door

1. Place the door on the bottom hinge pin.

2. Align the door with the top hinge hole and replace the top

1. Remove the white decorative screws from the opposite side

of the door and set aside.

2. Remove the screws from the magnetic door catch and

replace it on the opposite side of the door.

hinge pin.

3. Replace the handle and handle screws.

On Some Models—Replace Door Wrap

1. Place the door wrap flange onto the door top and ensure that

it fits correctly.

2. Rotate the door wrap downward until it covers the door

surface completely.

3. Install the 2 hex-head screws into the bottom of the door.

3. Install the white decorative screws on the opposite side of the

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

door.

4. Plug into a grounded 3 prong outlet.

Leveling

It is important for the ice maker to be level in order to work properly. Depending upon where you install the ice maker, you may need to make several adjustments to level it. You may also use the leveling legs to lower the height of the ice maker for undercounter installations.

Tools Needed

Gather the required tools and parts before starting installation.

■ 9" level

■ Adjustable wrench

NOTE: It is easier to adjust the leveling legs if you have another person to assist you.

1. Move the ice maker to its final location. NOTE: If this is a built-in installation, move the ice maker as

close as possible to the final location.

2. Place the level on top of the product to see whether the ice maker is level from front to back and side to side.

3. Push up on the top front of the ice maker, and then locate the leveling screws that are on the bottom front of the ice maker.

4. Using an adjustable wrench, change the height of the legs as follows:

■ Turn the leveling leg to the right to lower that side of the

ice maker.

■ Turn the leveling leg to the left to raise that side of the ice

maker.

NOTE: The ice maker should not wobble. Use shims to add stability when needed.

5. Push up on the top rear of the ice maker and locate the

leveling legs that are on the bottom rear of the ice maker.

6. Follow the instructions in Step 4 to change the height of the

legs.

7. Use the level to recheck the ice maker to see that it is even

from front to back and side to side. If the ice maker is not level, repeat steps 2 to 5. If the ice maker is level, go to the “Connect Water Supply” section.

Water Filtration System

Install the Water Filter

1. Locate the accessory packet in the ice maker and remove the

water filter.

2. Take the water filter out of its packaging and remove the

cover from the O-rings. Be sure the O-rings are still in place after the cover is removed.

A. Cover B. O-rings

3. The water filter compartment is located in the right-hand side

of the ice maker controls.

C. Alignment pin D. Alignment arrow

4. Using the arrow pointing to the alignment pin on the side of

the filter and the arrow inside the control housing, align the alignment pin with the cutout notch and insert the filter into the housing.

The Water Filter Status Light

The water filter status lights will help you know when to change your water filter.

■ The “Order Filter” status light will be illuminated when it is

time to order a replacement filter.

■ The “Replace Filter” status light will be illuminated when it is

time to replace the filter.

■ Replacing the disposable water filter with a new filter will

automatically reset the filter status tracking feature. See “Using the Controls.”

NOTES:

■ “Replace Filter” will remain illuminated if a filter is not

installed.

■ The “Filter” status light will flash if the filter is not correctly

installed or there is an obstruction in the water line.

A. Alignment pin B. Unlocked symbol C. Locked symbol

5. Turn the filter clockwise until it locks into the housing. Ensure that the alignment arrow on the filter head aligns with the locked symbol on the control box housing.

NOTE: If the filter is not correctly locked into the housing, the ice maker will not produce ice.

D. Cutout notch inside control housing

E. Arrow pointing to cutout notch F. Arrow pointing to alignment pin

A. Alignment arrow aligned with locked symbol

ICE MAKER USE

How Your Ice Maker Works

When you first start your ice maker, the water pan will fill and the system will rinse itself before starting to make ice. The rinsing process takes about 5 minutes.

Under normal operating conditions, the ice maker will cycle at preset temperatures. The ice level sensor located in the ice storage bin will monitor the ice levels.

IMPORTANT: If the water supply to the ice maker is turned off, be sure to set the ice maker control to OFF.

Replace the Water Filter

To purchase a replacement water filter, see “Accessories.” Replace the disposable water filter when indicated on the water

filter status display or at least every 9 months. If the ice making rate decreases before the Replace Filter light illuminates, then replace the filter.

1. Locate the water filter compartment in the right-hand side of

the control housing. See Step 3 in the “Install Water Filter” section.

2. Turn the water filter counterclockwise (to the left), and pull it

straight out of the compartment. NOTE: There may be some water in the filter. Some spilling

may occur.

3. Install the replacement water filter by following steps

2 through 5 in the “Install the Water Filter” section.

2. When the desired thickness is reached, the ice sheet is

released and slides onto a cutter grid. The grid divides the sheet into individual cubes.

The Ice Making Process

1. Water is constantly circulated over a freezing plate. As the

water freezes into ice, the minerals in the water are rejected. This produces a sheet of ice with a low mineral content.

3. The water containing the rejected minerals is drained after

each freezing cycle.

4. Fresh water enters the machine for the next ice making cycle.

5. Cubes fall into the storage bin. When the bin is full, the ice maker shuts off automatically and restarts when more ice is needed. The ice bin is not refrigerated, and some melting will occur. The amount of melting varies with room temperature.

Clean

It is recommended that you clean the ice maker when the “Cleaning Needed” light is illuminated or 9 months has elapsed or ice production decreases significantly. To clean your ice maker, see “Ice Maker System” in the “Cleaning” section.

Door Ajar Alarm

The Door Ajar Alarm feature sounds an alarm when the ice maker door is open for 5 minutes. The alarm will repeat every 2 minutes. Close the door to turn off. The feature then resets and will reactivate when the door is left open again for 5 minutes.

NOTE: As the room and water temperatures vary, so will the amount of ice produced and stored. This means that higher operating temperatures result in reduced ice production.

Using the Controls

1. To start ice production, press ON/OFF.

2. To stop ice maker operation, press ON/OFF.

NOTES:

■ Pressing the On/Off button does not shut off power to the ice

maker.

■ Allow 24 hours to produce the first batch of ice. Discard the

first 2 batches produced.

Fast Ice Mode

Select the Fast Ice feature when you have an upcoming need for a large amount of ice and the ice bin is low or empty. Fast Ice mode will produce a greater quantity of ice in a 24-hour period.

■ Press FAST ICE while the ice maker is on. The indicator light

will illuminate.

■ Press FAST ICE again to turn off the Fast Ice feature. The

indicator light will turn off.

■ The Fast Ice mode will be on when you first turn on the

product. It will turn off after 24 hours. To turn Fast Ice back on, press FAST ICE.

Normal Sounds

Your new ice maker may make sounds that are not familiar to you. Because the sounds are new to you, you might be concerned about them. Most of the new sounds are normal. Hard surfaces such as floors, walls and cabinets can make the sounds seem louder than they actually are. The following describes the kinds of sounds that might be new to you and what may be making them.

■ You will hear a buzzing sound when the water valve opens to

fill the water pan for each cycle.

■ Rattling noises may come from the flow of the refrigerant or

the water line. Items stored on top of the ice maker can also make noises.

■ The high-efficiency compressor may make a pulsating or high

pitched sound.

■ Water running over the evaporator plate may make a

splashing sound.

■ Water running from the evaporator plate to the water pan may

make a splashing sound.

■ As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your ice maker.

■ You may hear air being forced over the condenser by the

condenser fan.

■ During the harvest cycle, you may hear a “thud” when the ice

sheet slides from the evaporator onto the cutter grid.

■ When you first start the ice maker, you may hear water

running continuously. The ice maker is programmed to run a rinse cycle before it begins to make ice.

■ If the ice maker is connected to a water supply pressure in

excess of 60 psi, you may hear a loud sound during water filling associated with the flow of water through the inlet valve. Call a licensed, qualified plumber to determine the best method to reduce the supply water pressure (50 psi is recommended).

ICE MAKER CARE

A B

WARNING

Electrical Shock Hazard Disconnect power before cleaning. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

Cleaning

The ice making system and the air cooled condenser need to be cleaned regularly for the ice maker to operate at peak efficiency and to avoid premature failure of system components. See the “Ice Maker System” and the “Condenser” sections.

Exterior Surfaces

Wash the exterior enamel surfaces and gaskets with warm water and mild soap or detergent. Wipe and dry. Regular use of a good household appliance cleaner and wax will help maintain the finish. Do not use abrasive cleaners on enamel surfaces as they may scratch the finish.

For products with a stainless steel exterior, use a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners. Do not use chlorine bleach on the stainless steel surfaces.

Ice Maker System

Minerals that are removed from water during the freezing cycle will eventually form a hard scaly deposit in the water system. Cleaning the system regularly helps remove the mineral scale buildup. How often you need to clean the system depends upon how hard your water is. With hard water of 15 to 20 grains/gal. (4 to 5 grains/liter), you may need to clean the system as often as every 9 months.

NOTE: Use one 16 oz (473 mL) bottle of approved ice maker cleaner. To order, see “Accessories.”

1. Press the ON/OFF button.

2. Wait 5 to 10 minutes for the ice to fall into the storage bin.

Remove all ice from the storage bin.

3. Unscrew the drain cap from the bottom of the water pan

located inside the storage bin as shown. Allow the water to drain completely.

4. Replace the drain cap securely on the water pan. If the drain

cap is loose, water will empty from the water pan and you will have either thin ice or no ice.

5. Read and follow all handling information on the cleaner bottle

before completing the steps below. Use one 16 oz (473 mL) bottle of approved ice maker cleaner.

6. Pour one bottle of solution into the water pan. Fill the bottle

twice with tap water and pour it into the water pan.

7. Press the CLEAN button. See “Using the Controls.” The

Clean button will blink, indicating that the cleaning cycle is in process. When the “Cleaning Complete” light is illuminated (approximately 70 minutes), the cleaning cycle is complete. During the cleaning cycle, the system will both clean and rinse itself.

8. After the cleaning cycle is complete, remove the drain cap

from the water pan. Look for any cleaning solution left in the water pan. If cleaning solution drains from the water pan, you should run the clean cycle again. Be sure to refill the water pan with cleaner before starting the clean cycle again. Be sure to replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan and you will have either thin ice or no ice.

NOTE: Severe scale buildup may require repeated cleaning with a fresh quantity of cleaning solution.

9. Press the ON/OFF button to resume ice production.

Condenser

A Dirty or Clogged Condenser

■ Obstructs proper airflow.

■ Reduces ice making capacity.

■ Causes higher than recommended operating temperatures

which may lead to component failure.

1. Unplug ice maker or disconnect power.

2. Remove the 2 screws in the lower access panel and the

2 screws from the base grille area of the front panel support.

3. Pull the bottom forward and then pull down to remove the

lower access panel.

A. Water pan B. Drain cap

4. Remove dirt and lint from the condenser fins and the unit

A B C

E F

A B

compartment with a brush attachment on a vacuum cleaner.

A. Condenser fins

5. Replace the lower access panel using the 4 screws.

6. Plug in ice maker or reconnect power.

NOTE: Make sure the plastic spacer from the right-hand side

of the cutter grid bracket stays with the cutter grid.

A. Cutter grid harness B. Screw

C. Cutter grid

D. Ice level sensor harness

E. Plastic spacer F. S c re w

Interior Components

1. Unplug ice maker or disconnect power.

2. Open the storage bin door and remove any ice that is in the

bin.

3. Remove the drain cap from the water pan and drain

thoroughly. Replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

4. Pull out on the bottom of the cutter grid cover until the snaps

release to remove.

5. Unplug the wiring harness from the left side of the cutter grid.

A. Cutter grid cover

8. Remove the mounting screw that holds the water pan in

place. Pull out on the front of the water pan.

9. Disconnect the pump bracket from the water pan and unplug

the water pan drain pump.

A. Water pan B. Water pan screw

C. Drain cap D. Drain pump cover

10. Remove, clean and replace the ice scoop and ice scoop

holder. NOTE: On some models, the ice scoop holder is located in

the upper left of the unit, and on other models, the ice scoop holder is located in the lower left of the unit.

■ After removing the ice scoop, remove the holder by

removing the 2 screws.

■ Wash the ice scoop holder along with the other interior

components using the following instructions.

■ Replace the ice scoop holder by replacing the screws.

6. Unplug the ice level sensor from the right side of the cutter

grid. Pull the ice level sensor down and forward away from the cutter grid.

7. Remove the right-hand and left-hand screws. Lift the cutter

grid up and out.

A. Screw B. Ice scoop holder

11. Wash the interior components (cutter grid, exterior of hoses,

WARNING

Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C).

12. To replace the water pan, set the water pan inside the ice bin.

Hook up the water pan pump. Snap the pump bracket back onto the water pan and place back into position. Secure the water pan by replacing the mounting screw.

Vacation and Moving Care

To Shut Down the Ice Maker:

1. Unplug ice maker or disconnect power.

2. Remove all ice from storage bin.

3. Shut off the water supply.

4. Remove the 2 screws in the lower access panel and the

2 screws from the base grille area of the front panel support. Pull forward to remove the lower access panel.

13. Check the following:

■ Drain cap from the water pan is securely in place. If the

drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

■ Hose from water pan is inserted into storage bin drain

opening.

14. Slide the cutter grid back into place and secure it by

replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid harness and the ice level sensor harness.

15. Replace the cutter grid cover.

16. Gently wipe the control panel with a soft, clean dishcloth

using warm water and a mild liquid dish detergent.

17. Plug in ice maker or reconnect power.

18. After cleaning, make sure that all controls are set properly

and that no control indicators are flashing.

5. Disconnect the inlet and outlet lines to water valve. Allow

these lines to drain and then reconnect to the valve.

6. Replace lower access panel and screws.

7. Drain water from water pan by removing the drain cap.

8. If the room temperature will drop below 32°F (0°C), water

must be removed from the drain line.

For Ice Makers with a Drain Pump Installed:

■ Plug in ice maker or reconnect power.

■ Turn ice maker off and remove all remaining ice from ice

bin.

■ Pour 1 qt (0.95 L) of water into the ice bin near the drain

and let the ice maker stand for approximately 5 minutes. This will allow the water in the bin to drain into the drain pump so that the pump will remove the remaining water from the ice bin and the drain pump.

■ Unplug ice maker or disconnect power.

9. Before using again, clean the ice maker and storage bin.

10. Plug into a grounded 3 prong outlet. NOTE: All components of the ice maker are permanently

lubricated at the factory. They should not require any additional oiling throughout the normal life of the machine.

TROUBLESHOOTING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

First try the solutions suggested here or visit our website and reference FAQs

(Frequently Asked Questions) to possibly avoid the cost of a service call.

In the U.S.A., www.maytag.com In Canada, www.maytag.ca

Ice Maker Operation

PROBLEM RECOMMENDED SOLUTIONS

Ice Maker Will Not Operate

Ice Maker Seems Noisy Is the water in the reservoir overflowing? This is normal. This overflow helps to purge minerals that

Check that it is plugged into a grounded 3 prong outlet. Check that the control is turned on. See “Using the Controls.” Replace the fuse or reset the circuit breaker. NOTE: If problems continue, contact an electrician. Room temperature must be above 55°F (13°C). Otherwise, bin thermostat may sense cold room

temperature and shut off even though the bin is not full of ice. The ice maker may not restart once it does shut off.

If there was a large amount of water added to the ice maker, wait a few minutes for the drain pump to clear. If there is still water in the bin, check to see whether the drain hose is kinked.

For models with drain pumps, check that the drain hose is not damaged, or kinked or pinched between cabinet and ice maker. Use only Whirlpool approved drain pump kit, Part Number 1901A.

were removed from the water during the ice making process. Is there a “whooshing” sound? Check the following things:

■ Check that the water supply is hooked up and turned on.

■ Check that the drain cap is tight and the water drain pan pump is securely attached to the water

pan.

Is there ice between the evaporator plate and the cutting grid? Check that the ice maker is level. See “Leveling.” If the ice maker is level, and the problem persists, run a cleaning cycle. See “Cleaning.”

If the ice maker is connected to a water supply pressure in excess of 60 psi, you may hear a loud sound during water filling associated with the flow of water through the inlet valve. Call a licensed, qualified plumber to determine the best method to reduce the supply water pressure (50 psi is recommended).

Ice Production

WARNING

Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

PROBLEM RECOMMENDED SOLUTIONS

Ice Maker Runs But Produces No Ice

Ice Maker Runs But Produces Very Little Ice

Check that the control is turned on. Check that the water supply is properly connected and turned on. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no

ice. Tighten the drain cap. Clean the drain tube. Check that there are no kinks in the drain line.

Is the accelerated ice production feature turned on? This feature increases the ice production rate to provide you with more ice in the same amount of time. See “Using the Controls.”

Room temperatures of more than 90ºF (32ºC) will normally reduce ice production. Dirt or lint may be blocking the airflow through the condenser. See “Condenser” in the “Cleaning”

section. If there is white scale buildup in the ice maker’s water or freezing system, you should clean the ice

maker. See “Interior Components” in the “Cleaning” section. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no

ice. Tighten the drain cap. Ensure that the cutter grid is securely in place and that its harness plug is connected. See “Interior

Components” section of “Cleaning” for instructions on cutter grid removal. Check that water filter is properly installed.

Ice Quality

PROBLEM RECOMMENDED SOLUTIONS

Off Taste, Odor or Gray Color in the Ice

Is there unusually high mineral content in the water supply? The water may need to be treated. Is there mineral scale buildup? Clean your ice maker. See “Ice Maker System” in the “Cleaning”

section. Do not store any foods in the ice bin. Check that all packaging materials were removed at the time of installation.

Thin, Soft or Clumps of Ice Is there unusually high mineral content in the water supply? The water may need to be treated.

Is there mineral scale buildup? Clean your ice maker. See “Ice Maker System” in the “Cleaning”

section. Are there clumps of ice in the bin? If ice is not used regularly, it will melt and form clumps. Break

the clumps with the ice scoop provided.

Plumbing Problems

WARNING

Excessive Weight Hazard Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

PROBLEM RECOMMENDED SOLUTIONS

Water Not Entering Drain Properly

Is the drain hose aligned over the drain? Move the ice maker to align the drain. See “Connect Water

Supply.” NOTE: Service technicians cannot repair plumbing problems outside of the ice maker. Call a licensed,

qualified plumber.

Accessories

To order accessories, in the U.S.A., visit our web site www.maytag.com/accessories or call 1-800-901-2042. In Canada, visit our web site www.whirlpoolparts.ca or call 1-800-807-6777.

Water Filter

Order Part Number F2WC9I1or ICE2

Cleaner

Order Part Number 4396808

affresh®* Stainless Steel Cleaner

In U.S.A., order Part Number W10355016 In Canada, order Part Number W10355016B

affresh is a trademark of Whirlpool, U.S.A.

affresh®* Stainless Steel Wipes

In U.S.A., order Part Number W10355049 In Canada, order Part Number W10355049B

affresh®* Kitchen & Appliance Cleaner

In U.S.A., order Part Number W10355010 In Canada, order Part Number W10355010B

PERFORMANCE DATA SHEET

® NSF is a registered trademark of NSF International.

Ice Maker Water Filtration System

Model P6GEG2KL, P6KG2KL, P6WG2KL Capacity 2000 Gallons (7571 Liters)

System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor.

This system has been tested according to NSF/ANSI Standards 42 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42.

Substance Reduction Aesthetic Effects

Chlorine Taste/Odor 50% reduction 1.9727 mg/L 2.0 mg/L ± 10% 0.71 mg/L 0.7788 mg/L 70.2 72.81

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.50 gpm (1.89 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 2000 gallons (7571 liters).

■ It is essential that operational, maintenance, and filter

replacement requirements be carried out for the product to perform as advertised.

■ Use replacement filter P6RFWG2K, P6RFGEG2K,

P6RFKG2K, Part Number ICE2. Style 1 – When the water filter status display changes from

“GOOD” to “ORDER,” order a new filter. When the filter indicator reads “REPLACE,” it is recommended that you replace the filter.

Style 2 – Press FILTER to check the status of your water filter. If the filter indicator light is yellow and the words “ORDER FILTER” appear on the display screen, order a new filter. If the filter indicator light is red, it is recommended that you replace the filter.

■ These contaminants are not necessarily in your water supply.

While testing was performed under standard laboratory conditions, actual performance may vary.

■ The product is for cold water use only.

■ Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after the system.

NSF Reduction Requirements

Average Influent

Influent Challenge Concentration

■ Refer to the “Warranty” section for the Manufacturer’s name,

■ Refer to the “Warranty” section for the Manufacturer’s limited

Water Supply Water Pressure Water Temperature Service Flow Rate

Maximum Effluent

Average Effluent

Minimum % Reduction

address and telephone number.

warranty.

Application Guidelines/Water Supply Parameters

City or Well 30 - 120 psi (207 - 827 kPa) 33°- 100°F (0.6° - 37.8°C)

0.50 gpm (1.89 Lpm) @ 60 psi

Average % Reduction

MAYTAG® MAJOR APPLIANCE WARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter “Maytag”) will pay for factory specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Maytag designated service company. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in which it was purchased. Outside the 50 United States and Canada, this limited warranty does not apply. Proof of original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is

contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by Maytag.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Maytag within 30 days from the date of purchase.

6. Any food loss due to refrigerator or freezer product failures.

7. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be

repaired in the home and only in-home service is covered by this warranty.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Maytag servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with published installation instructions.

11. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty

is void if the factory applied serial number has been altered or removed from your major appliance.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.

If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.

For additional product information, in the U.S.A., visit www.maytag.com In Canada, visit www.maytag.ca

If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may contact Maytag at the number below.

Have your complete model number ready. You can find your model number and serial number on the label, located on the inside wall of the ice maker compartment.

For assistance or service in the U.S.A., call 1-800-688-9900. In Canada, call 1-800-807-6777. If you need further assistance, you can write to Maytag with any questions or concerns at the address below: In the U.S.A.:

Maytag Brand Home Appliances Customer eXperience Center 553 Benson Road

Benton Harbor, MI 49022-2692 Please include a daytime phone number in your correspondence. Please keep this User Instructions and model number information for future reference.

10/12

In Canada:

Maytag Brand Home Appliances Customer eXperience Centre 200 – 6750 Century Ave. Mississauga, Ontario L5N 0B7

+ 44 hidden pages

Maytag MIM1554ZRS User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual