Maytag MHWZ600TW02, MHWZ400TQ02, MHWZ400TB02 Owner’s Manual
FCI&YI'AG®
AUTOMATIC WASHER
USE & CARE GUIDE
LAVEUSE AUTOMATIQU E
GUIDE D'UTILISATION ET D'ENTRETIEN
FOR QUESTIONS ABOUT FEATURES, OPERATION/PERFORMANCE, PARTS, ACCESSORIES OR SERVICE
CAI.I.: 1.800.688.9900
IN CANADA, CAI.I.: 1.800.807.6777
VISIT OUR WEBSITE AT WWW.MAYTAG.COM
IN CANADA, WWW.MAYTAG.CA
PARA OBTENER ACCESO AI. MANUAl. DE USO Y CUIDADO EN ESPAI'_OI., O PARA OBTENER INFORMACION ADICIONAI. ACERCA DE SU PRODUCTO, VISITE: WWW.MAYTAG.COM.
TENGA I.ISTO SU N_JMERO DE MODEI.O COMPI.ETO. PODRA ENCONTRAR El. N_JMERO DE MODEI.O Y DE SERIE EN I.A ETIQUETA UBICADA DEBAJO DE I.A TAPA DE I.A I.AVADORA.
W10151563A
AU CANADA, POUR DES QUESTIONS ,_ PROPOS DES CARACTERISTIQUES, DU
FONCTIONNEMENT/RENDEMENI, DES PIECES, DES ACCESSOIRES OU DU SERVICE,
COMPOSEZ I.E : 1.800.807.6777
OU VISITEZ NOTRE SITE INTERNET ,_
WWW.MAYTAG.CA
i_i_iiii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_iiiiiiiiiiII_i_i_i_iii_iii_iii_iii_iii_iii_iii_iii_iii_iii_iii_ii_ii_ii_ii_ii¸I¸i_iiiiiiiiiiliiii'ii_i_ii'ii_i_ii'ii_i_ii'ii_i_i_ii_ii_ii_i,iiY_i__iiiiii!!!ii¸_ iiii_iii!ii_i_ii'ii'ili_i_iiiiiiiiiiliiii'i_ii,i_ii,i_ii,i_ii,i_i_iiiii_i_i_iii!i_i_i,i_ii,_,i_i_i_ii'ili_i_i_ii'ili_i_i_ii'ii'iii_i
TABLE OF CONTENTS
WASHER SAFETY .................................................................................................................... 3
INSTALLATION REQUIREMENTS ........................................................................................... 5
Tools and Parts ..................................................................................................................... 5
Options ................................................................................................................................ 5
I.ocation Requirements ......................................................................................................... 6
Drain System ........................................................................................................................ 8
Electrical Requirements ........................................................................................................ 9
INSTALLATION INSTRUCTIONS ........................................................................................ 10
Remove Transport System ................................................................................................. 10
Connect the Inlet Hoses .................................................................................................... 10
Route the Drain Hose ........................................................................................................ 11
Secure the Drain Hose ...................................................................................................... 12
I_eve[ the Washer ............................................................................................................... 12
Complete Installation ........................................................................................................ 12
FEATURES AND BENEFITS ................................................................................................... 13
WASHER USE ....................................................................................................................... 14
Starting Your Washer ........................................................................................................ 14
Using the Proper Detergent ............................................................................................... 14
Using the Dispenser .......................................................................................................... 15
Pausing or Restarting ......................................................................................................... 16
Changing Cycles, Options and Modifiers .......................................................................... 16
Status Iights ....................................................................................................................... 17
Cycles ............................................................................................................................... 17
Norman Sounds ................................................................................................................. 19
Options ............................................................................................................................. 19
Modifiers ........................................................................................................................... 19
I_aundry Guide .................................................................................................................. 20
LAUNDRY TIPS .................................................................................................................... 21
I.oading ............................................................................................................................ 21
Stain Removal Guide ........................................................................................................ 22
WASHER CARE ..................................................................................................................... 23
Cleaning Your Washer ...................................................................................................... 23
Water Inlet Hoses .............................................................................................................. 24
Vacation, Storage, and Moving Care ................................................................................. 24
TROUBLESHOOTING .......................................................................................................... 25
Washer and Components .................................................................................................. 25
Washer Operation ............................................................................................................. 26
Clothes Care ...................................................................................................................... 28
ASSISTANCE OR SERVICE .................................................................................................... 29
In the U.S.A ....................................................................................................................... 29
In Canada .......................................................................................................................... 29
Accessories ....................................................................................................................... 29
WARRANTY ......................................................................................................................... 30
TABLE DES MATIERES
SI_CURITI_ DE LA LAVEUSE .................................................................................................. 31
EXIGENCES DqNSTALLATION ............................................................................................ 33
Outillage et pi_ces ............................................................................................................ 33
Options ............................................................................................................................. 33
Exigences d'emplacement ................................................................................................. 34
Syst_'me de vidange ........................................................................................................... 36
Sp6cifications 6[ectriques .................................................................................................. 36
INSTRUCTIONS DqNSTALLATION .................................................................................... 37
Elimination des accessoires de transport ........................................................................... 37
Raccordement des tuyaux d'a[imentation ......................................................................... 38
Acheminement du tuyau de vidange ................................................................................. 39
Immobilisation du tuyau de vidange ................................................................................. 39
R6g[age de ['aplomb de [a [aveuse .................................................................................... 40
Achever ['installation ......................................................................................................... 40
CARACTI_RISTIQUES ET AVANTAGES ................................................................................ 41
UTILISATION DE LA LAVEUSE ............................................................................................ 42
Mise en marche de Ha [aveuse ........................................................................................... 42
Utilisation du d6tergent appropri6 ..................................................................................... 42
Uti[isation du distributeur .................................................................................................. 43
Pause et remise en marche ................................................................................................ 44
Changement des programmes, options et modificateurs ................................................... 44
T6moins [umineux ............................................................................................................. 45
Programmes ...................................................................................................................... 46
Sons normaux ................................................................................................................... 47
Options ............................................................................................................................. 47
Modificateurs .................................................................................................................... 48
Guide de [essivage ............................................................................................................ 49
CONSEILS DE LESSIVAGE .................................................................................................... 50
Chargement ...................................................................................................................... 50
Guide pour ['6[imination des taches .................................................................................. 51
ENTRETIEN DE LA LAVEUSE ................................................................................................ 52
Nettoyage de Ha[aveuse .................................................................................................... 52
Robinets d'arriv6e d'eau .................................................................................................... 53
Pr6cautions _ prendre avant [es vacances, un entreposage ou un d6m6nagement ............ 53
DI_PANNAGE ....................................................................................................................... 54
I.a [aveuse et ses composants ............................................................................................ 54
Fonctionnement de [a [aveuse ........................................................................................... 56
Entretien des v&tements ..................................................................................................... 57
ASSISTANCE OU SERVICE ................................................................................................... 58
Aux Etats-Unis ................................................................................................................... 58
Au Canada ........................................................................................................................ 58
Accessoires ........................................................................................................................ 59
GARANTIE ............................................................................................................................ 59
2
WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
_ 3
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,
including the following:
[] Read all instructions before using the washer.
[] Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
m Do not add gasoline, dry-cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
m Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
this time.
SAVE THESE INSTRUCTIONS
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
Before the washer is removed from service or discarded,
remove the door or lid.
[] Do not reach into the washer if the drum, tub or agitator is
moving.
[] Do not install or store the washer where it will be exposed to
the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user-repair instructions that you understand and
have the skills to carry out.
[] See "Electrical Requirements" for grounding instructions.
4 .....
INSTALLATION REQUIREMENTS
and
Gather the required tools and parts before starting installation. The parts supplied are in the
washer drum.
Tools needed for connecting the water inlet hoses
• Pliers (that open to 1_/ld' [39.5 mm]) • Flashlight (optional)
Tools needed for installation
• Open end wrenches 14 mm • Wood block
and 13 mm
• I.eve[
Parts supplied
A
B C D
• Ruler or measuring tape
A. U-shaped hose form
B. Water inlet hoses (2)
C. Inlet hose washers (4)
D. 7}ansit bolt hole plug (4)
E. Beaded tie strap
If You Have You Will Need to Buy
I)rain hose too short 4 ft (1.2 m) drain hose extension kit, Part Number 285863
Water faucets beyond reach 2 longer water fill hoses:
of fill hoses 6 ft (1.8 m) Part Number 76314
10 ft (3.0 m) Part Number 350008
Pedestal
You have the option of purchasing pedestals of different heights separately for this washer. You
may select a 10" (25.4 cm) or a 15.5" (39.4 cm) pedestal The pedestal will add to the total
height of the washer.
Optional pedestal
Alternate Parts
Your installation may require additional parts. If you are interested in purchasing one of the
items listed here, ca[[ the toll-free number on the cover or in the "Assistance or Service"
section.
If You Have You Will Need to Buy
I_aundry tub or standpipe Sump pump system (if not aheady available)
taller than 96" (2.4 m)
Overhead sewer Standard 20 gal. (76 I.), 30" (76.2 cm) tall drain tub or
utility sink and sump pump (available from local plumbing
suppliers)
Floor drain Siphon break, Part Number 285834; additional drain hose,
Part Number 8318155; and connector kit, Part
Number 285835
Pedestal Height Approximate height Color Model Number
with washer
10" (25.4 cm) 46" (116.8 cm) White MHP1000SQ0
10" (25.4 cm) 46" (116.8 cm) Black MHP1000SB0
15.5" (39.4 cm) 51.5" (130.8 cm) White MHP1500SQ0
15.5" (39.4 cm) 51.5" (130.8 cm) Black MHP1500SB0
15.5" (39.4 cm) 51.5" (130.8 cm) Blue MHP1500SK0
Stack Kit
Are you planning to stack your washer and dryer? To do so, you will need to purchase a Stack
Kit.
To ordeb ca[[ the dealer from whom you purchased your washer or refer to the "Assistance or
Service" section. Ask for Part Number 8572546.
Selectingtheproperlocationforyourwasherimprovesperformanceandminimizesnoiseand WasherDimensions
possible washer "walk."
Your washer can be installed under a custom counteb or in a basement, laundry room, closet,
or recessed area. See "Drain System."
Companion appliance location requirements should also be considered. Proper installation is
your responsibility.
You will need
A water heater set to deliver 120°F (49°C) water to the washer.
A grounded e[ectrica[ outlet [ocated within 6 ft (1.8 m) of where the power cord is
attached to the back of the washer. See "Electrical Requirements."
Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves,
and water pressure of 20-100 psi (137.9-689.6 kPa).
A [eve[ f[oor with a maximum s[ope of 1u (2.5 cm) under entire washer. Installing the
washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not
recommended.
• A sturdy and solid f[oor to support the washer with atotal weight (water and [oad) of
400 [bs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the
washer and can cause damage in low temperatures. See "Washer Care" for information on
winterizing.
Installation clearances
• The location must be large enough to allow the washer door to be fully opened.
• Additional spacing should be considered for ease of installation and servicing. The door
opens more than 90 °, and it is not reversible.
• Additional clearances might be required for wall, door, and floor moldings.
• Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce
noise transfen
• Companion appliance spacing should also be considered.
Recommended installation spacing for custom undercounter installation
The dimensions shown are for the recommended spacing.
Custom undercounter installation - Washer only
27"
(68.6 crn)
36"
(91.4cm)
Door is not reversible.
(2.5crn) ' (68.6crn) --(2.5 crn)
6
Recommended installation spacing for recessed or closet installation, with or
without a pedestal
Recommended installation spacing for recessed or closet installation, with
stacked washer and dryer
The dimensions shown are for the recommended spacing.
Recessed area or closet installation
48 Jrl.2
(310 cm2)"
A. Side view - closet o1confined area
B. Closet door with vents
*Min. top and bottom air openings for closet door.
Recessed or closet installation - Washer on pedestal
The dimensions shown are for the recommended spacing.
48 in.2 *
(316 cm2)
3"
(7.6cm)
3"(7.6crn)
f
o
(7.6cm)
B
24(n.2.
(156crn2)
T
3"(7.6crn)
1"(2.6crn)
12"(_0.5crn)
72" __ ......... J
(182.9cm)
A B
A. Recessed area
B.Side view - closet or confined area
5Y4"**--}_,,_ _ 1 ''f _ _,9[:-27"-_,_
13.3cm) (2.5crn) 68.6cm)
*Min. top and bottom air openings for closet door.
** External exhaust elbow requires additional space.
+Wall, door and floor molding may require additional spacing.
Recommended installation spacing for cabinet installation
The dimensions shown are for the recommended spacing.
For cabinet installation, with a door, the minimum ventilation openings in the top are
required.
" . )
7"(17.8cm)
9"
(22.9cm)
The washer can be installed using the standpipe drain system (floor or wall), the laundry tub
drain system, or the floor drain system. Select the drain hose installation method you need.
See "Tools and Parts."
Standpipe drain system - wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum
carry-away capacity can be no less than 17 gal. (64 I_)per minute.
The top of the standpipe must be at least 30" (76.2 cm) high and no higher than 96" (2.4 m)
from the bottom of the washer.
4 31Y2 1
(10.2cm) (80cm) (2.5cm)(2.5cm)(68.6cm) (2.5cm)
A B
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 I.) capacity. The top of the laundry tub must be
at [east 30" (76.2 cm) above the floor.
Floor drain system (view D)
The floor drain system requires a siphon break that may be purchased separately. See "Tools
and Parts."
The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer.
Additional hoses might be needed.
26";.ioX
(66 Cm)
C D
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failureto follow these instructions can result in death,
fire, or electrical shock.
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-
delay fuse or circuit breaker is recommended. It is recommended that a separate circuit
serving only this appliance be provided.
This washer is equipped with a power supply cord having a 3 prong grounding plug.
To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong,
grounding-type outlet, grounded in accordance with local codes and ordinances. If a
mating outlet is not available, it is the personal responsibility and obligation of the
customer to have the properly grounded outlet installed by a qualified electrician.
If codes permit and a separate ground wire is used, it is recommended that a qualified
electrician determine that the ground path is adequate.
• I)o not ground to a gas pipe.
• Check with a qualified electrician if you are not sure the washer is properly grounded.
• I)o not have a fuse in the neutral or ground circuit.
GROUNDING INSTRUCTIONS
For a grounded, cord=connected washer:
This washer must be grounded. In the event of a malfunction
or breakdown, grounding will reduce the risk of electrical
shock by providing a path of least resistance for electric
current. This washer is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local
codes and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in
doubt as to whether the appliance is properly grounded.
Do not modify the plug provided with the appliance - if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician.
For a permanently connected washer:
This washer must be connected to a grounded metal,
permanent wiring system, or an equipment grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on
the appliance.
11_1/_(.)_ { G_t_ _¸'_
Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.
IMPORTANT: Position the washer so that the rear of the washer is within approximately 3 ft
(90 cm) of its final location.
There are 4 blue bolts in the rear panel of the washer that support the suspension system
during transportation. These bolts also retain the power cord inside the washer until the bolts
are removed.
°
Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers in
the couplings.
A B
A. Coupling
B.Washer
Connect the inlet hoses to the water faucets
Make sure the washer drum is empty.
1. Attach a hose to the hot water faucet. Screw on coupling by hand until it is seated on the
washer.
2. Attach a hose to the cold water faucet. Screw on coupling by hand until it is seated on the
washer.
3. Using pliers, tighten the couplings with an additional two-thirds turn.
1o
Using a 13 mm wrench, loosen each of the bolts.
2.
Once the bolt is loose, move it to the center of the hole and completely pull out the bolt,
including the plastic spacer covering the bolt.
3. Once all 4 bolts are removed, discard the bolts and spacers. Then pull the power cord
through the opening of the rear panel and close the hole with the attached cap.
4. Close the bolt holes with the 4 transport bolt hole plugs.
NOTE: If the washer is to be transported at a later date, call your local service center. To avoid
suspension and structural damage, your machine must be properly set up for relocation by a
certified technician.
10
NOTE: I)o not overtighten or use tape or sealants on the valve. Damage to the valves can
result.
Clear water lines
Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket,
to get rid of particles in the water lines that might clog the inlet valve screens.
Check the temperature of the water to make sure that the hot water hose is connected to
the hot water faucet and that the cold water hose is connected to the cold water faucet.
Connect the inlet hoses to the washer
Proper routing of the drain hose protects your floor from damage due to water leakage. Read
and follow these instructions.
Remove drain hose from the washer
Gently pull the corrugated drain hose from the shipping dips.
Laundry tub drain or standpipe drain
Connect the drain hose form to the corrugated drain hose.
/
H. Hot water inlet
C. (_;M water inlet
1. Attach the hot water hose to the washer's hot (H) water inlet valve. Screw on coupling by
hand until it is seated on the washer.
2. Attach the cold water hose to the washer's cold (C) water faucet. Screw on coupling by
hand until it is seated on the washer.
3. Using pliers, tighten the couplings with an additional two-thirds turn.
NOTE: Do not overtighten. Damage to the coupling can result.
4. Turn on the water faucets completely and check for leaks.
NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record
hose installation or replacement dates on the hoses for future reference.
Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.
A. Snap either end of the drain hose form to the drain hose at
the point where the corrugation begins.
B. Bend drain hose over drain hose form and snap into place.
To keep drain water from going back into the washer:
• Do not straighten the drain hose, and do not force excess drain hose into standpipe. Hose
should be secure, but loose enough to provide a gap for air.
• Do not lay excess hose on the bottom of the laundry tub.
Floor drain
You may need additional parts. See Floor drain under "Tools and Parts."
1.
Drape the power cord over the washer top.
Move the washer to its final location.
2.
3.
Place the drain hose in the laundry tub or standpipe as shown. See illustrations A and B.
A B C
4. If the washer faucets and the drain standpipe are recessed, put the hooked end of the
drain hose in the standpipe as shown. See illustration C.
NOTES:
• 13o not force excess drain hose back into the rear of the washer.
• To avoid siphoning, do not sea[ the drain hose into the standpipe.
Properly leveling your washer avoids excessive noise and vibration.
1. Check the levelness of the washer by placing a level on the top edge of the washe_; first
side to side, then front to back.
1. Check the electrical requirements. Be sure that you have the correct electrical supply and
the recommended grounding method. See "Electrical Requirements."
2. Check that all parts are now installed. If there is an extra part, go back through the steps to
see which step was skipped.
3. Check that you have all of your tools.
4. Dispose of/recycle all packaging materials.
5. Check that the water faucets are on.
6. Check for leaks around faucets and inlet hoses.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
If the washer is against a wall, move the washer out slightly before tipping back. If the
washer is not [eve[, first prop the front with a wood block and adjust the feet as necessary;
then prop the back and adjust feet as necessary. Repeat this step until washer is [eve[.
2.
Make sure all four feet are stable and resting on the floor. Then check that the appliance is
perfectly [eve[ (use a [eve[).
3.
After the washer is [eve[, use a 14 mm open-end wrench to turn the nuts on the feet tightly
against the washer cabinet.
IMPORTANT: All four feet must be tightened. If the nuts are not tight against the washer
cabinet, the washer may vibrate.
4.
The washer should not move front to back, side to side, or diagonally when pushed on its
top edges.
5.
Slide the washer to its final location.
6.
Confirm the levelness of the washer.
12
7.
Plug into a grounded 3 prong outlet.
8.
Read "Washer Use."
9.
To test and to clean your machine, make sure there are no clothes in the washer and add
one AFFRESH r,, tablet to the washer drum. Select Powe_; the Clean Washer cycle and
then select START. This cycle will take approximately 50 minutes to complete. Allow the
washer to complete the entire cycle without interruption.
_iilli_iii/lillii_iiii;ii_iiii;ii_iiii;i_ii/ii//li_iiiiiiiiiiiiiiiiiii¸iiiiiiii¸ii_ii//llliiiiiiiiiiiiiiiiiiiiiii[_iiiiiiiii/iiii¸_iiiii_ii_iiii=iiii=ii_iii=iiii=iiii=iiii=iiii=iiii=ii_i_i_i_i_iiiiiii_Iiii_iii/lililliii//lllii;iii_i_iiiiiiiii/!iiiiiii;iii_i;iiiiii;iiiiiiii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iii_i;iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
FEATURES AND BENEFITS
Your new front-loading high efficiency washeb was help conserve to conserve resources and
lower your water and energy bills. The washer is designed to determine and then provide the
amount of water needed for the best performance. The time of operation may be greater for
this new system than for a conventional washer.
Electronic Controls
Flexible electronic controls are easy to use whether you are a beginner or an expert.
Auto Water Level
Adjusting to the size of the load, this feature allows the washer to use the minimal amount of
water needed to clean and rinse the clothes. With a low water level, you can obtain the same
results with smaller amounts of laundry products. Because only the required amount of water
is used, the washer saves energy, too. You can obtain the same washing results for small and
large loads size.
Larger Load Size
Since there is no agitator; you can wash large_; bulkier items such as an average size sleeping
bag. You are also able to wash more clothes at one time, which means fewer loads. You can
wash a pillow or a large stuffed teddy bear.
Suspension System
To reduce washer "walk" and "off-balance" conditions, your new washer combines:
• 2 Springs to isolate vibration
• 4 Shock absorbers at the washer base to minimize movement
Stainless Steel Drum
The stainless steel drum eliminates corrosion and enables higher spin speeds for more water
extraction, helping to reduce drying time.
Adaptive Variable Speed Motor
The motor adapts to the load size and to the cycle selected to give the optimum cleaning,
rinsing, and spinning conditions. The motor can handle slow speeds needed for delicate items
and is powerful enough to drive an average clothes load up to high-speed spin.
Spin Speeds
This washer automatically selects the spin speed based on the cycle selected. This factory
setting can be changed, however. This washer offers up to three different spin speed choices.
Thermal Optimizer
The heating system ensures that the wash water is heated to the preset temperature for Super
Wash, Whites, and Sanitary cycles. It also provides "Stepped Cleaning" when using the
Sanitary cycle. "Stepped Cleaning" starts the wash cycle with warm water to remove stains
(such as blood or grass). The Sanitary cycle also helps eliminate 99.9% of K. pneumonia, R
aureginosa and S. aureus, which are three common infectious bacteria.
Add A Garment
This option is available in all wash cycles except Rinse & Spin, Spin Only and Clean Washer.
When this option is available at the beginning of the cycle, the Add A Garment status light
will illuminate for the first 7 minutes. This washer allows a 7-minute period in which other
garments may be added to a load.
Dynamic Balance
A precision balancing system that allows the washer to reach high-speed spins. The washer
spins faster so that clothes coming out of the washer will have less moisture than with
traditional top load machines. In addition, if the Dynamic Balance system detects off-balance
loads during spinning, it redistributes the clothes so that they are evenly balanced.
Detergent Advantage System Dispenser
The three compartments in the dispenser allow loading of all laundry products before the
washer is started. The products will be dispensed into the wash at the optimal time for high-
performance cleaning. The bleach release system is included in the detergent advantage
system. The detergent is added at the beginning of the cycle, and the bleach is added after the
enzymes have had a chance to do their cleaning. The fabric softener is dispensed in the rinse
cycle or in the EXTRA RINSE, if selected. The Detergent Advantage System Dispenser tray can
be easily removed for cleaning.
!"'?"i
Use only HL High Lfficiency detergent.
WASHER USE
POWER
ADD A PREWAsHGARMENTcLEANRINsEWASHsPINI @ WHITEs-SUPER
CONTROLS LOCKED :ll! SANITARY
DOOR LOCKED ::lill
NOTE: The panel shown above may be different from that of your model.
SS_<_4:ng _ur sher
RAPID
D EU CAT E ESTIMATEDTIM_REMAININGWAS H
Q PREWASH
START
CANCEL@PAUSE/
I!:
Q
SPEEDSPIN
}!ii co 0 i i{iii° OoO
T£Oc ::
TEMP
ALL AUTOT_MPcoNfro L
Usng I:he?_@er D_{e_e;st
Use only High Efficiency detergents. The package for this type of detergent will be marked
"HE" or "High Efficiency." This wash system, along with less water, will create too much
sudsing with a regular non-HE detergent. Using regular detergent will likely result in washer
errors, longer cycle times, and reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made to produce the right amount
of suds for the best perforrnance. Follow the manufacturer's instructions to deterrnine the
amount of detergent to use.
Fire Hazard
Never place items in the washer that are dampened
with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Doing so can result in death, explosion, or fire.
WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the
IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
The following is a guide to using your washer. Please refer to specific sections of this manual
for more detailed information.
Do not store laundry products on the top surface of this washen Vibration is normal during
operation.
14 .......................................................................................
First Wash Cycle Without Laundry
Before washing clothes for the first time, if not completed during the final installation step,
choose the Normal cycle and run it without clothes. Use only HE High Efficiency detergent.
Use V2 the manufacturer's recommended amount for a mediurn-size load. This initial cycle
serves to ensure the interior is clean before washing clothes.
Use only HE High _ffic ien( y dete_ent.
For All Wash Cycles
1.
To load washer
Open the washer door by pulling on the handle. Sort laundry according to color and type
of fabric. Place a load of sorted clothes in the washen I])o not overload washer.
Overloading can cause poor cleaning.
• The washer can be fully loaded, but not tightly packed. Washer door should close
easily.
Mix large and small items. Avoid washing a single item. I.oad evenly.
Wash small items such as infant socks in mesh garment bags. It is recommended that
more than one garment bag be used and that each garment bag be filled with equal
amounts of material.
• When unloading garments, occasionally check under the gray colored seal/bellow
rim at the front of the tub for small items.
2.
Close the washer door by pushing it firmly until the lock clicks. The washer door will
remain locked during the wash cycle.
NOTE: The door can be opened only if PAUSE/CANCEl. is selected while the ADD A
GARMENT light is illuminating or if the cycle has been canceled. See "To cancel a cycle"
in the "Changing Cycles, Options and Modifiers" section.
3.
Open the dispenser drawer and add laundry products to the detergent, bleach, or fabric
softener compartments. Close drawer slowly to avoid spills. See "Using the Dispenser."
NOTE: Use only HE High Efficiency detergent.
4. Turn on the washer by selecting POWER. Select one of the cycles by turning the cycle
selector. The indicator light for the selected cycle will illuminate. When selecting a Wash
Cycle, the preset Modifiers and Options, Water Temp, and Spin Speed for the selected
cycle will illuminate. The preset settings provide the recommended fabric care for the
selected cycle. See "Cycles."
5. Select the desired OPTIONS such as Prewash, MAXEXTRACT r_, Stain Cycle or Extra
Rinse. Not all Options are available with all cycles. See "Options."
6. Select the desired MODIFIERS, such as Spin Speed and Wash/Rinse Temp. Not all
Modifiers are available with all Cycles and Options. See "Modifiers."
7. If desired, select the CYCI.E SIGNAL. The signal is helpful when you are washing items
that should be removed from the washer as soon as it stops. Press CYCI.E SIGNAl. once to
turn it on. The indicator light will illuminate. Press again to turn it off.
8. To begin the wash cycle immediately
Select and hold START (for approximately 1 second).
• If you do not select START within 5 minutes of choosing a cycle, the washer
automatically shuts off.
When the wash cycle is complete, the CI_EAN status light illuminates, the door
unlocks, and the wash load can be removed from the washer. The washer powers
down automatically 5 minutes after the cycle is complete and the Clean light stays on
until the door is opened or PAUSE/CANCEl_ is selected. To power down the washer
manually after the wash cycle is complete, select PAUSE/CANCEl. once.
9.
To begin the wash cycle later
Select DEI_AY WASH until the desired delay time (in hours) shows in the Estimated Time
Remaining display. Select START. The countdown to the wash cycle will show in the
display window.
IMPORTANT: When delaying a cycle, use only powdered detergents in the main wash
compartment since liquid detergents may seep out of the compartment during Delay,
before the wash cycle begins.
Your new washer has a dispenser drawer with three separate compartments for your laundry
products--one is for detergent, one is for liquid chlorine bleach, and one is for liquid fabric
softener. I.aundry products are diluted and dispensed automatically at the proper time during
the wash cycle, making it unnecessary for you to return to the washer during the cycle to add
them.
It is normal for small amounts of water to remain in the dispensers when the wash cycle is
complete.
I])o not put laundry products directly into the wash tub. Always use the proper dispensers
when adding laundry products.
Choosing the Right Detergent ....
Use only High Efficiency detergents. The package for this type of detergent will be marked ...........
"HE" or "High Efficiency." This wash system, along with less water, will create too much sudsing
with a regular non-HE detergent. Using regular detergent will likely result in washer errors, longer [[[
cycle times, and reduced rinsing performance. It may also result in component failures and
noticeable mold or mildew. HE detergents are made to produce the right amount of suds for the
best performance. Follow the manufacturer's instructions to determine the amount of detergent
to use.
Use only HE High Lfficiency detergent.
TO fill dispenser compartments
1. Pull out the dispenser drawer.
2. Add the desired laundry product to the proper compartment.
3. Push in the dispenser drawer slowly and completely (to avoid a spill).
A ........................... _ _ _ .........................
..........XuZH
B
Fabric softener compartment
(letter I) in Dispenser Illustration)
Add V4 cup (60 ml) liquid fabric softener to this compartment Fabric softener will be
automatically dispensed in the final rinse or in the EXTRA RINSE, if selected
• Do not fill beyond the "MAX" level
1.
To pause the washer at any time, select PAUSE/CANCEl .....
2.
To continue the cycle, select and hold START (for approximately 1 second).
Not all Options and Modifiers are available with all Cycles.
Cycles, Options and Modifiers can be changed anytime before START is selected.
To stop a cycle and select a new cycle
Dispenser
A. Dispenser release lever
B. Main Wash detergent compartment
C. Liquid chlorine bleach compartment
D. f_bHc softener compartment
Main Wash detergent compartment
(letter B in Dispenser Illustration)
Add liquid or powdered HE detergent to this compartment for your main wash cycle
• Powdered color safe bleach may be added to the Main Wash compartment along with the
powdered detergent
• Use the measurement device which comes with the detergent Add no more than the
manufacturer's recommended amount
NOTE: Overfilling could cause an oversudsing condition.
Chlorine bleach compartment
(I.etter C in Dispenser Illustration)
Add NO MORE THAN % cup (160 ml_) liquid chlorine bleach to this compartment. The
bleach will be automatically diluted and dispensed at the best time during the first rinse after
the wash cycle. This compartment cannot dilute powdered bleach.
• Use only liquid chlorine bleach in this dispensen Do not use this dispenser to add
powdered chlorine or any form of color-safe bleach to your load.
Always measure liquid chlorine bleach. Use a measuring cup with a pour spout; do not
guess. Follow the manufacturer's directions for proper use.
Do not fill beyond the "MAX" level.
NOTE: Overfilling could cause garment damage
1. Select PAUSE/CANCEl. twice.
2. Select POWER.
3. Select desired cycle.
4. Select the desired OPTIONS such as Prewash, MAXEXTRACT rM, Stain Cycle or Extra
Rinse.
5. Select the desired MODIFIERS such as Spin Speed or Wash/Rinse Temp.
6. Select and hold START (for approximately 1 second) to restart the washer at the beginning
of the new cycle.
To cancel a cycle
1. Select PAUSE/CANCEl. twice.
2. The washer powers down, the door unlocks, and clothes can be removed.
NOTE: If the water level or the temperature is too high, the washer will drain automatically
before the door unlocks.
To change Options or Modifiers after the cycle has started
1.
Select PAUSE/CANCEl .....
2.
Select the desired Spin Speed, Wash/Rinse Temp or OPTION (such as Prewash,
MAXEXTRACT r_*, Stain Cycle or Extra Rinse). If the modifier or option are not available,
the machine will beep.
3.
Select and hold START (for approximately 1 second) to continue the cycle.
To drain the washer manually
1. Select PAUSE/CANCEl .....
2. Select SPIN Only.
3. Select and hold START (for approximately 1 second) to begin the drain.
4. When the spin is complete, the door unlocks. Items can be removed from the washer.
16
These lights show which portion of the cycle the washer is operating. They also indicate when
you can add an additional item to the wash cycle and when the controls are locked.
ADD A GARMENT
PREWASH
WASH
RINSE
SPIN
CLEAN
CONTROLS LOCKED
DOORLOCKED
Adding items
You can add items to the washer after the wash cycle has started, if the ADD A GARMENT
status light is illuminating. All cycles have this feature except Rinse & Spin, Spin Only and
Clean Washer.
To add items
1. Select PAUSE/CANCEl.. The washer door unlocks, and items can be added.
2. To continue the cycle, close the door and select and hold START (for approximately
1 second).
NOTE: To add garments after the ADD A GARMENT period is over, the wash cycle needs to
be canceled, the items added, and a new wash cycle started.
Clean
The Clean light comes on when the cycle is complete. The light will stay on until the door is
opened or PAUSE/CANCEl_ is selected.
Estimated Time Remaining
The cycle times vary automatically based on your water pressure, water temperature,
detergent, and clothes load. The cycle time will be extended if oversudsing occurs or the load
is unbalanced. The SUDs routine removes extra suds and assures proper rinsing of your
garments. During the unbalance routine the time displayed may pause until this activity is
complete, then resume with the remainder of the cycle. The options you select will also affect
the cycle times that are shown in the Preset Cycle Settings table. The Estimated Time
Remaining can change up to 30 minutes under extreme conditions. If a small load of clothing
is run, the Estimated Time Remaining display will indicate 3 or more minutes, but the cycle
will finish immediately. If a large load of clothing is run, the Estimated Time Remaining
display may indicate 1 minute, but the cycle will take approximately 5 minutes to finish.
Door Locked
When the status light illuminates, the door is locked.
Choose Wash Cycle by rotating the Cycle selector knob to the desired cycle. The indicator ...........
light for the cycle selected will illuminate. Each cycle is designed for different types of fabric
and soil levels.
NOTE: The cycle selector shown below may be different from that of your modem.
RAPID
WASH DELICATE
SUPER
WASH " "ONLY
HAND
' WASH
SPIN
Locking controls
The Control I_ock avoids unintended use of the washer. You can also use the control lock
feature to avoid unintended cycle or option changes during a cycle. When CONTROI_S
I_OCKED is [it, all buttons are disabled except for PAUSE/CANCEl. and POWER. You can lock
the controls while the washer is operating.
To lock the controls
Select and hold CYCI.E SIGNAl. for 3 seconds.
IHO_ CYCLE SIGNAL
The CONTROI_S I_OCKEI) status light illuminates.
To unlock the controls
Select and hold CYCI.E SIGNAl. for 3 seconds until the CONTROI.S I.OCKED Status light
turns off.
WHITES-
SANITARY ,CLEAN
RINSE
WASHER
Each cycle has a preset cycle time, WASH/RINSE TEMP, SPIN SPEED and may have preset
Options. The preset settings provide the recommended fabric care for the selected cycle.
The preset settings can be changed anytime before START is selected. Not all Options and
Modifiers are available with all Cycles. To change settings after the cycle has started,
select PAUSE/CANCEl., then select the desired settings. Select and hold START (for
approximately 1 second) to continue the cycle.
Preset Cycle Settings
Normal
Each cycle has a preset Cycle Time, Water Temp, and Spin Speed. The preset settings provide
the recommended fabric care for the selected cycle. See chart.
Cycle Estimated Time* Wash/Rinse Temp Spin Speed
(hr:min)
Sanitary 3 H Extra Hot High
Whites 1:30 - 2H Hot High
Super Wash 1:30 Hot High
Normal :56 Warm High
Rapid Wash :30 Warm High
(2-3 items)
Delicate :34 Cold I.ow
Handwash :37 Cold I.ow
Spin Only :14 N/A High
Rinse & Spin :26 Cold High
Clean Washer :56 N/A High
*The cycle times vary automatically based on your water pressure, water temperature,
detergent, and clothes load. The cycle time will be extended if oversudsing occurs or the
load is unbalanced.
Sanitary
Use this cycle to clean heavily soiled, colorfast fabrics. This cycle combines an extra hot
water temperature and fast speed tumbling to help ensure the removal of heavy soils and
stains. It is recommended that you set your hot water heater to 120°F (49°C) to ensure proper
performance during this cycle.
Whites
This cycle is especially designed for cleaning loads of soiled white fabrics with the addition of
bleach. Hot washing temperatures assure optimal bleach activity. An additional rinse provides
optimal rinse performance to avoid chlorine residue on your laundry. This cycle combines
fast-speed tumbling, longer wash time, and high-speed spin to shorten drying time.
Super Wash
Use this cycle to wash loads of sturdy, colorfast fabrics and Heavy soiled garments. This cycle
combines fast-speed tumbling, longer wash time, and high speed spin to shorten drying times.
Use this cycle to wash loads of no-iron fabrics such as sport shirts, blouses, casual business
clothes, permanent press blends, cottons and linens, and synthetic fabrics. This cycle
combines medium-speed tumbling, high-speed spin, and a load cooling process to reduce
wrinkling.
Rapid Wash
Use this cycle to wash small loads of lightly soiled garments that are needed in a hurry. This
cycle combines fast-speed tumbling, a shortened wash time, and high speed spin to shorten
drying time. I_arge wash loads will result in the machine increasing the wash time.
Delicate
Use this cycle to clean washable silk and ultra delicate garments. (Check [abe[ instructions to
make sure that garment is washable.) This cycle gently tumbles and drains without spinning to
gently clean garments and minimize wrinkling. Garments will contain a higher amount of
water at the end of this cycle, because there is a low spin-speed at the end of the cycle.
• Use mesh garment bags to wash undergarments such as underwire bras, items with
strings, and small items such as socks.
Handwash
Use this cycle to clean washable woolen and special care garments. (Check label instructions
to make sure that the garment is washable.) Similar to the way garments are hand washed in a
sink, the wash action of this cycle combines periods of extra-low tumbling speeds and
soaking. I_ow spin speeds minimize wrinkling.
• Use mesh garment bags as needed.
Spin Only
Use this cycle to drain your washer or to drain and spin your wash load. The spin speed is
preset to high. If desired, you can reduce the spin speed by selecting the speed you want from
the SPIN SPEED modifier.
NOTE: I_oads of synthetics, delicate fabrics, handwashables, and woolens should be drained
with no spin or low spin to avoid fabric stress.
To use Spin Only setting
• Select SPIN Only cycle.
• Press START.
Rinse&Spin
Use this cycle to rinse, drain, and spin your wash load. This cycle combines fast-speed
tumbling and high-speed spin. If desired, you can reduce the spin speed by selecting the
speed you want from the SPIN SPEED modifier.
Rinse & Spin is useful for
• Loads that need rinsing only.
• Adding fabric softener to a load using the fabric softener dispenser.
18 ....
Loading...