Maytag MHWE900VW01, MHWE900VW00, MHWE900VJ01, MHWE900VJ00 Owner’s Manual
PERFORMANCE SERIES
FRONT-LOADING AUTOMATIC WASHER
USE & CARE GUIDE
LAVEUSEAUTOMATIQUE A CHARGEMENT FRONTAL
GUIDE D'UTILISATION ET D'ENTRETIEN
FOR QUESTIONS ABOUT FEATURES, OPERATION/PERFORMANCE,
PARTS, ACCESSORIES OR SERVICE CAll: 1.800.688.9900
IN CANADA, CAll: 1.800.807.6777
VISIT OUR WEBSIIE AT WWW.MAYTAG.COM
IN CANADA, WWW.MAYTAG.CA
Certified to SanitizeCertifid pour aseptiser
W10176969A
W10207215A-SP
AU CANAl)A, POUR ASSISTANCE, INSIAI I i_IION OU SERVICE,
COMPOSER IE : 1.800.807.6777
OU VISITER NOTRE SITE INTERNET
WWW. MAYTAG. CA
Designed to use only HE High Efficiency detergent
Congu pour I'utilisation d'un ddtergent haute efficacitd seulement
,i_!_ii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i_i_i_ii!i¸i!i!i!i!i!i!i!i_i_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_i_iiiiYiiiiii//li¸il¸iiii_ii,i_ii,i_ii,i_ii,i_ii,i_i_iii_i_ii_il'ii_i_iil'ii_i_iil_i_ii_i_ii_i_ii_ii_i_ii_:ii:_:i_:ii:_:i_:ii:_:i_:ii:_:i_:ii:_:i_:ii:_:i_:ii:Z_,,i_i!i!i_,¸¸¸¸¸¸¸'_''_'_'_'_'_'_'_'_'_'_'_'_'_'_'_'__¸_¸_¸_¸_!iiiiiiiiiiiiiiil¸il¸ii_ii_ii¸I¸I¸il¸ii_ii¸ii_ii¸ii_ii¸ii_iil¸ii_i_iil¸I¸iiiii_iiiii_i_i_ii_i_iiiii_1i_iii_1i_iii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_!i_!_!_
TABLE OF CONTENTS
WASHER SAFETY .................................................................. 3
INSTALLATION REQUIREMENTS ......................................... 4
Tools and Parts ................................................................... 4
Options .............................................................................. 5
I.ocation Requirements ....................................................... 6
Drain System ...................................................................... 8
Electrical Requirements ...................................................... 8
INSTALLATION INSTRUCTIONS ......................................... 9
Remove Transport System .................................................. 9
Connect the Inlet Hoses ................................................... 10
Route the Drain Hose ....................................................... 10
Secure the Drain Hose ..................................................... 11
I_eve[ the Washer .............................................................. 11
Complete Installation ....................................................... 11
FEATURES AND BENEFITS .................................................. 12
WASHER USE ...................................................................... 13
Starting Your Washer ........................................................ 13
Using the Proper Detergent .............................................. 13
Using the Dispenser ......................................................... 14
Pausing or Restarting ........................................................ 15
Changing Cycles, Options, and Modifiers ........................ 16
Status Indicator ................................................................. 16
Cycles .............................................................................. 17
Options ............................................................................ 18
Modifiers .......................................................................... 19
LAUNDRY GUIDE ............................................................... 20
LAUNDRY TIPS ................................................................... 20
I.oading ............................................................................ 21
WASHER CARE .................................................................... 21
CHeaning Your Washer ..................................................... 21
Water Inlet Hoses ............................................................. 22
Vacation, Storage, and Moving Care ................................ 22
TROUBLESHOOTING ......................................................... 23
ASSISTANCE OR SERVICE ................................................... 26
In the U.S.A ...................................................................... 26
In Canada ......................................................................... 26
WARRANTY ........................................................................ 27
TABLE DES MATIERES
SI_CURITI_ DE LA LAVEUSE ................................................. 28
EXIGENCES D'INSTALLATION ........................................... 29
Outillage et pi_ces ............................................................ 29
Options ............................................................................ 30
Exigences d'empHacement ................................................ 30
Syst6me de vidange .......................................................... 32
Sp6cifications 6[ectriques ................................................. 33
INSTRUCTIONS DqNSTALLATION .................................... 34
EHimination des accessoires de transport ........................... 34
Raccordement des tuyaux d'a[imentation ......................... 34
Acheminement du tuyau de vidange ................................ 35
ImmobiHisation du tuyau de vidange ................................ 35
R6g[age de ['aplomb de [a [aveuse ................................... 36
Achever ['installation ........................................................ 36
CARACTI_RISTIQUES ET AVANTAGES ................................ 37
UTILISATION DE LA LAVEUSE ........................................... 38
Mise en marche de Ha[aveuse .......................................... 38
UtiHisation du d6tergent appropri6 .................................... 38
Uti[isation du distributeur ................................................. 39
Pause ou remise en marche .............................................. 41
Changement des programmes,
options et modificateurs ................................................... 41
T6moins [umineux ............................................................ 41
Programmes ..................................................................... 42
Options ............................................................................ 43
Modificateurs ................................................................... 44
GUIDE DE LESSIVAGE ........................................................ 45
CONSEILS DE LESSIVAGE ................................................... 46
Chargement ...................................................................... 46
ENTRETIEN DE LA LAVEUSE ............................................... 47
Nettoyage de Ha[aveuse ................................................... 47
Tuyaux d'arriv6e d'eau ..................................................... 48
Pr6cautions _ prendre avant [es vacances,
un entreposage ou un d6m6nagement .............................. 48
DI_PANNAGE ....................................................................... 49
ASSISTANCE OU SERVICE .................................................. 53
Aux Etats-Unis .................................................................. 53
Au Canada ....................................................................... 53
GARANTIE ....................................................................... 55
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions,
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
iiiiiiiii!ii
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,
including the following:
[]
[] Read all instructions before using the washer.
[] Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not add gasoline, dry-cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
[] Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
this time.
SAVE THESE INSTRUCTIONS
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
[]
Before the washer is removed from service or discarded,
remove the door or lid.
[] Do not reach intothe washer if the drum, tub or agitator is
moving.
[] Do not install or store the washer where it will be exposed to
the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user-repair instructions that you understand and
have the skills to carry out.
[] See "Electrical Requirements" for grounding instructions.
INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation. The parts supplied are
in the washer drum.
Tools needed for connecting the water inlet hoses
• Pliers (that open to 1"/.," [39.5 mm])
• Flashlight (optional)
4
Tools needed for installation
• Open end wrenches 17 mm and 13 mm
• I.evel
• Wood block
• Ruler or measuring tape
Parts supplied:
B
Pedestal
C
0
A.Drain hose form
B.Inlet hose (2)
C.Inlet hose washers (4)
D. hansport boh hole plug (4)
E.Beaded strap
Alternate Parts
Your installation rnay require additional parts. If you are interested in purchasing one of the
items listed here, ca[[ the toll-free number on the cover or in the "Assistance or Service"
section.
If You Have You Will Need to Buy
I_aundry tub or standpipe Sump pump system (if not already available)
taller than 96" (2.4 m)
Overhead sewer Standard 20 gal. (76 I), 30" (76.2 cm) tall drain tub or
utility sink and sump pump (available from local plumbing
suppliers)
Floor drain Siphon break, Part Number 285834; additional drain hose
Part Number 8318155; and connector kit, Part
Number 285835
Drain hose too short
Water faucets beyond reach
of fill hoses
4 ft (1.2 m) drain hose extension kit, Part Number 285863
2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008
A pedestal will add to the total height of the washer for a total height of 53.5" (135.9 cm).
Optional pedestal
This pedestal is available in several colors. '''i
To order; call the dealer from whom you purchased your washer or refer to the "Assistance or ,_:_i
Service" section.
Pedestal Height Color Part Number
1O" (25.4 cm) White MH P1000SQ
15.5" (39.4 cm) White XH P1550VW
15.5" (39.4 cm) Crimson XH P1550VF
15.5" (39.4 cm) Evergreen XH P1550VP
15.5" (39.4 cm) Oxide XH P1550VJ
Stack Kit
Are you planning to stack your Maytag washer and dryer? To do so you will need to purchase
a Stack Kit.
To order; call the dealer from whom you purchased your dryer or refer to the "Assistance or
Service" section. Ask for Part Number 8212640.
Z'I
! ,. ._,':_. _ _ _ _,,'__ _ _'_d_'_ C
Lo ation
Selecting the proper location for your washer improves performance and minimizes noise and Washer Dimensions
possible washer "walk."
Your washer can be installed under a custom counter, or in a basement, laundry room, closet,
or recessed area. See "Drain System."
Companion appliance location requirements should also be considered. Proper installation is
your responsibility.
You will need
• A water heater set to deliver 120°F (49°C) water to the washer.
• A grounded electrical outlet located within 6 ft (1.8 m) of where the power cord is
attached to the back of the washer. See "Electrical Requirements."
• Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves,
and water pressure of 20-100 psi (137.9-689.6 kPa).
• A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the
washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not
recommended.
• A sturdy and solid floor to support the washer with a total weight (water and load) of
400 [bs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the
washer and can cause damage in low temperatures.
Installation clearances
• The location must be large enough to allow the washer door to be fully opened.
• Additional spacing should be considered for ease of installation and servicing.
• Additional clearances might be required for wall, doob and floor moldings.
• Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce
noise transfer.
Recommended installation spacing for custom undercounter installation
The dimensions shown are for the recommended spacing.
Custom undercounter installation - Washer only
• Companion appliance spacing should also be considered.
39" rnin.
(99.0cm)
51"
(129,5cm)
1" _ 27"i-_- 1"
(2.5 cm) (68.6 cm) (2.5 cm)
(81.3cm)
Recommended installation spacing for recessed or closet installation,
with or without a pedestal
Recommended installation spacing for recessed or closet installation,
with stacked washer and dryer
The dimensions shown are for the recommended spacing.
Recessed area or closet installation
48 in,2*........_
34"
-- (86.4cml
1" 1_'..-32"---_ 4"
{2.5cm)(81.3cm)(10.2cm)
(310cm2)
24in,2*-...._
(155cm2)
A B
A. Side view - closet or confined area
B.Closet door with vents
Recessed or closet installation - Washer on pedestal
-- 18"rnin.
\\_//
,_ 3"
-{
(45,7crn),
(7,6crn)
The dimensions shown are for the recommended spacing.
48 in.2*
(310cm2)
3"* (7.6cm)
O
T
24 in.2*
(155cm2)
3"* (7.6cm)
* Required spacing
6"* (_5.2cm)
76" _
(193cm)
i_i_'_!S _'i;_i_!i_
1"*(2.5cm)
1"--._ 27" --'_1" 51/2,,**__-
(2.5crn) (68,6cm) (2,5crn) (14cm)
A B
A. Recessed area
B. Side view - closet or confined area
(2,5crn)(81,3cm)(10,2cm)
* Required spacing
** For venting out the side, 1" (2.5 cm) spacing is allowed.
1" -_, _ _:- 27" -_
(2.5cm) (68.6 cm) (2.5cm)
Recommended installation spacing for cabinet installation
• The dimensions shown are for the recommended spacing.
• For cabinet installation, with a doo_, the minimum ventilation openings in the top are
required.
7"(17.8cm)
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. 176 I.) capacity. The top of the laundry tub must
be at least 30" 176.2 cm) above the floor.
Floor drain system (view D)
The floor drain system requires a siphon break that may be purchased separately. See
"Tools and Parts."
The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer.
Additional hoses might be needed.
l|
(22.9cm)
4" 32" 1" 1" 27" 1"
(t0.2cm) (81.3cm) (2.5cm)(2.5crn)(68.8cm) (2,5crn)
The washer can be installed using the standpipe drain system (floor or wall), the laundry tub
drain system, or the floor drain system. Select the drain hose installation method you need.
See "Tools and Parts."
Standpipe drain system - wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of 2" 15 cm). The minimum
carry-away capacity can be no less than 17 gal. (64 I_)per minute.
The top of the standpipe must be at least 30" (76.2 cm) high and no higher than 96" (2.4 m)
from the bottom of the washer.
30" rnin.
(76.2cm)
L
28"_ _ _ L_
(71?_
C
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. Time-
delay fuse or circuit breaker is recommended. It is recommended that a separate circuit
serving only this appliance be provided.
D
B
• This washer is equipped with a power supply cord having a 3 prong grounding plug.
• To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong,
grounding-type outlet, grounded in accordance with local codes and ordinances. If a
mating outlet is not available, it is the personal responsibility and obligation of the
customer to have the properly grounded outlet installed by a qualified electrician.
• If codes permit and a separate ground wire is used, it is recommended that a qualified
electrician determine that the ground path is adequate.
• Do not ground to a gas pipe.
• Check with a qualified electrician if you are not sure the washer is properly grounded.
• Do not have a fuse in the neutral or ground circuit.
GROUNDING INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back orother injury.
For a grounded, cord-connected washer:
This washer must be grounded• In the event of a malfunction
or breakdown, grounding will reduce the risk of electrical
shock by providing a path of least resistance for electric
current• This washer is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local
codes and ordinances•
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock•
Check with a qualified electrician or serviceman if you are in
doubt as to whether the appliance is properly grounded•
Do not modify the plug provided with the appliance - if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician•
For a permanently connected washer:
This washer must be connected to a grounded metal,
permanent wiring system, or an equipment grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on
the appliance•
IMPORTANT: Position the washer so that the rear of the washer is within approximately
3 ft (90 cm) of its final location.
There are 4 bolts in the rear pane[ of the washer that support the suspension system during
transportation. These bolts also retain the power cord inside the washer until the bolts are
removed.
1. Using a 13 mm wrench, loosen each of the bolts.
2. Once the bolt is loose, move it to the center of the hole and completely pull out the bolt,
including the plastic spacer covering the bolt.
H'_i
3. Once all 4 bolts are removed, discard bolt and spacers. Then pull the power cord through
the opening of the rear pane[ and dose the hole with the attached cap.
4. Close the bolt holes with the 4 transport bolt hole plugs.
NOTE: If the washer is to be transported at a later date, ca[[ your local service center. To avoid
suspension and structural damage to your washer, it must be properly set up for relocation by
a certified technician.
1.
Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers
in the couplings.
A B
A. Coupling
B. Washer
2.
Make sure the washer drum is empty.
3.
Attach the hose with the red color indicator to the Hot (left) inlet valve. Attaching the red
coupling first makes it easier to tighten connection with pliers. Screw on coupling by
hand until it is seated on the washen
4.
Attach the hose with the blue color indicator to the Cold (right) water inlet valve. Screw
on coupling by hand until it is seated on the washen
9. Turn on the water faucets and check for leaks.
NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure.
Record hose installation or replacement dates on the hoses for future reference.
10. Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.
Proper routing of the drain hose protects your floors from damage due to water leakage.
Read and follow these instructions.
Remove drain hose from washer cabinet
Gently pull the corrugated drain hose from the shipping clips.
Laundry tub drain or standpipe drain
Connect the drain hose form to the corrugated drain hose.
H. Hot water inlet
C. Cold water inlet
5°
Using pliers, check the tightness of the hose couplings already attached to the washer.
NOTE: Do not overtighten. Damage to the coupling can result.
6.
Attach hot water hose to the hot water faucet. Screw on coupling by hand until it is seated
on the washer.
7.
Attach cold water hose to the cold water faucet. Screw on coupling by hand until it is
seated on the washer.
8.
Using pliers, tighten the couplings with an additional two-thirds turn.
NOTE: Do not overtighten. Damage to the coupling can result.
| 0
A B
A. _Sna[_9either..... end of the drain hose formto the drain hose at the
point where the corrugation begins.
B.Bend drain hose over drain hose form and snap into place.
To keep drain water from going back into the washer:
• Do not straighten the drain hose, and do not force excess drain hose into standpipe.
Hose should be secure, but loose enough to provide a gap for air.
• Do not lay excess hose on the bottom of the laundry tub.
Floor drain
You may need additional parts. See Floor drain under "Tools and Parts."
..................... _ _, .,,._,' ._
1.
Drape the power cord over the washer top.
2.
Secure the drain hose to the laundry tub leg or standpipe with the beaded strap provided.
(See illustrations A and B.)
A B C
If the washer faucets and the drain standpipe are recessed (see illustration C), put the
hooked end of the drain hose in the standpipe. Tightly wrap the beaded strap around the
water inlet hoses and the drain hose.
Do not force excess drain hose into the standpipe.
Properly leveling your washer avoids excessive noise and vibration.
1. Check the levelness of the washer by placing a level on the top edge of the washe_; first
side to side, then front to back.
1. Check the electrical requirements. Be sure that you have the correct electrical supply and
the recommended grounding method. See "Electrical Requirements."
2. Check that all parts are now installed. If there is an extra part, go back through the steps to
see which step was skipped.
3. Check that you have all of your tools.
4. Dispose of/recycle all packaging materials.
5. Check that the water faucets are on.
6. Check for leaks around faucets and inlet hoses.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
;Z!III
Z'I
If the washer is against a wall, move the washer out slightly before tipping back. If the
washer is not [eve[, first prop the front with a wood block and adjust the feet as necessary;
then prop the back and adjust feet as necessary. Repeat this step until washer is [eve[.
2.
Make sure all four feet are stable and resting on the floor. Then check that the appliance is
perfectly [eve[ (use a [eve[).
3.
After the washer is [eve[, use a 17 mm open-end wrench to turn the nuts on the feet tightly
against the washer cabinet.
IMPORTANT: All four feet must be tightened. If the nuts are not tight against the washer
cabinet, the washer may vibrate.
4.
The washer should not move front to back, side to side, or diagonally when pushed on its
top edges.
5.
Slide the washer to its final location.
6.
Confirm the levelness of the washer.
7.
Plug into a grounded 3 prong outlet.
8.
Read "Washer Use."
9.
To test and clean your washer, make sure there are no clothes in the washer and add one
AFFRESH r,, tablet to the washer drum. Select POWER/CANCEl_, the Clean Washer cycle,
and then select START/PAUSE. This cycle will take approximately 50 minutes to
complete. Allow the washer to complete the entire Clean Washer Cycle without
interruption.
Electronic Controls
Flexible electronic controls are easy to use whether you are abeginner or an expert.
Smart Dispensers
The Smart Dispensers make your washer truly automatic. This washer provides a four-
compartment dispenser which includes separate compartments for main wash detergent,
fabric softenec bleach, and auto oxi prewash or auto soak. The dispenser has large pour
zones. The dispenser is self-cleaning, and can be easily removed. I.aundry products are
diluted with fresh water and added to the load at the proper time in the wash cycle.
Steam Clean
This washer has a built-in steaming unit which is combined with the Steam Clean option to
provide multiple temperatures to help remove a variety of stains from garments. Steam Clean
may be active in the Whitest Whites, Heavy Duty, and Normal/Casual cycles.
High-Efficiency Wash System
Your new front-loading, high-efficiency washer saves time with fewer, larger loads, and lowers
your water and energy bills by helping conserve resources.
Spin Speeds
This washer automatically selects the spin speed based on the cycle selected. This factory
setting can be changed, however. This washer offers up to five different spin speed choices.
Heating Element
This washer has a heating element that automatically heats the water to the optimal
temperature on select cycles. This enables stepped cleaning, a process in which warm water
is brought in and mixed with detergent first, then the water is heated. Stepped cleaning starts
the wash cycle with warm water to help remove stains (such as blood and grass). This heater is
active in the Whitest Whites, Heavy Duty, and Normal/Casual cycles.
Oxi/Color-safe Bleach Dispenser
With the Oxi/Color-safe bleach dispenser and the Oxi Treat option, there is no need to come
back and add your oxygen-based stain fighter or your color-safe bleach. The washer will
automatically add these laundry products to the cycle. Delaying the introduction of these
laundry products helps remove many stains better.
Clean Washer Cycle
This cycle uses steam to raise the temperature of the unit and makes the washer self-cleaning,
flushing the machine's interior free of dirt and other residue. The use of AFFRESH r,_washer
cleaner or liquid chlorine bleach with this cycle will remove and help avoid odor-causing
residue.
Auto Water Level
This washer automatically adjusts water level for optimal cleaning and rinsing performance.
Two sensors determine load size, load composition, and suds level, then the sensors adjust
the water level to the proper setting. This eliminates guesswork. The water level is just right
for every wash load size.
Super Size Capacity
Since there is no agitatob you can wash largeb bulkier items such as a king-sized bedspread.
You are also able to wash more clothes at one time, which means fewer loads.
Smooth Balance _M Balance System
To reduce washer "walk" and "off-balance" conditions, your new washer combines:
• 2 Springs to isolate vibration
• 4 Shock absorbers at the washer base to minimize movement
Commercial Quality Stainless Steel Drum
The commercial quality stainless steel drum eliminates corrosion and enables higher spin
speeds for more water extraction, reducing drying time compared to traditional front-load
washers.
Automatic Temperature Control
The automatic temperature control electronically senses and maintains a uniform water
temperature. Automatic temperature control regulates incoming hot and cold water.
Automatic temperature control is automatically turned on when a cycle is selected.
Add Clothes
Clothes can be added to the load during the first 8 minutes of the cycle. During this time,
the Status Indicator will indicate it is okay to add clothes.
Special Cleaning Action with Sensi-Care _M Wash System
This washer channels 100% of the water through the dispensers to assure thorough rinse-out
and mixture of all the laundry products before they touch any garments. The water is then
sprayed from the top front onto the center of the load, providing even distribution, and
optimum cleaning performance. It is normal for small amounts of water to remain in the
dispensers when the wash cycle is complete.
Efficient Detergent System
This washer has a specially designed valve that closes during the wash portion of the cycle
so that 100% of the water and detergent mixture is used on the load. The Efficient Detergent
System ensures that no water or detergent is wasted.
Dynamic Off-Balance Detection
This washer uses two sensors to detect load size and the amount of off-balance within the
load. The suspension system and controls are specially designed to redistribute the load
automatically.
12
WASHER USE
9000 SERIES with steam
MCT _,y_agCommecal T_chnoogy
NOTE: The panel shown above may be different from that of your model.
Fire Hazard
Never place items in the washer that are dampened
with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Doing so can result in death, explosion, or fire.
WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the
IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
The following is a guide to using your washer. Please refer to specific sections of this manual
for more detailed information.
19o not store laundry products on the top surface of this washer. Vibration is normal during
operation.
start • palJse
O
Use only High Efficiency detergents. The package for this type of detergent will be marked
"HE" or "High Efficiency." This wash system, along with less water, will create too much
sudsing with a regular non-HE detergent. Using regular detergent will likely result in washei .............
errors, longer cycle tirnes, and reduced rinsing perforrnance. It rnay also result in cornponent ::',:i::::::
failures and noticeable mold or mildew. HE detergents are made to produce the right amount
of suds for the best perforrnance. Follow the rnanufacturer's instructions to deterrnine the ::::::::1:
amount of detergent to use.
Use only Hf_ High f_fficiency detergent.
First Wash Cycle Without Laundry
Before washing clothes for the first time, if not completed during the final installation step,
choose the Normal/Casual cycle and run it without clothes. Use only HE High Efficiency
detergent. Use _/_the manufacturer's recommended amount for a medium-size load. This
initial cycle serves to ensure the interior is clean before washing clothes.
For All Wash Cycles
1.
Open the washer door by pulling on the handle. Sort laundry according to color and type
of fabric. Place a load of sorted clothes in the washer. I)o not overload washer.
Overloading can cause poor cleaning.
• The washer can be fully loaded, but not tightly packed. Washer door should close easily.
• Mix large and small items and avoid washing single items. I_oad evenly.
• It is recommended that you wash small items such as infant socks in a mesh garment bag.
• When unloading garments, occasionally check under the gray colored seal at the
front of the tub for small items.
2.
Close the washer door by pushing it firmly until the lock clicks. The washer door will
remain locked during the wash cycle.
NOTE: After any wash cycle is completed, the door must be opened and then closed
before a new cycle can begin. The door can be opened only if START/PAUSE or
POWER/CANCEl_ is selected while the Add Clothes light illuminates or if the cycle has
been canceled. See "To cancel a cycle" in Changing Cycles, Options, and Modifiers
section.
3. Open the dispenser drawer and add laundry products to the detergent, oxi/co[or safe
bleach, chlorine bleach, or fabric softener compartments. Close drawer slowly to avoid
spills. See "Using the Dispenser."
4. Turn on the washer by selecting POWER/CANCEl_. Select one of the cycles by turning the
cycle selector. The indicator light for the selected cycle will illuminate. When selecting a
wash cycle, the preset Options, Wash Temp, Spin Speed, and Soil I_eve[ for the selected
cycle will illuminate. The display shows the estimated time remaining. The preset settings
provide the recommended fabric care for the selected cycle. See "Cycles."
5. Select the desired Options, such as Oxi Treat, Max Extract TM, Extra Rinse, and Steam
Clean. Not all options are available with all cycles. See "Options."
6. Select the desired Modifiers, such as Soil I_eve[, Wash Temp, and Spin Speed. Not all
modifiers are available with all cycles and options. See "Modifiers."
7. If desired, select SIGNAl_ ON/OFF. The signal is helpful when you are washing items that
should be removed from the washer as soon as it stops.
8. To begin the wash cycle immediately
Select START/PAUSE.
• If you do not select START/PAUSE within 60 minutes of choosing a cycle, the washer
automatically shuts off.
When the wash cycle is complete, the status indicator shows Done, the door unlocks,
and the wash load can be removed from the washer. The washer powers down
automatically 5 minutes after the cycle is complete and the Done light goes off. To
power down the washer manually after the wash cycle is complete, select POWER/
CANCEl. once.
Choosing the Right Detergent
Use only High Efficiency detergents. The package for this type of detergent will be marked
"HE" or "High Efficiency." This wash system, along with less water, will create too much
sudsing with a regular non-HE detergent. Using regular detergent will likely result in washer
errors, longer cycle times, and reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made to produce the right amount
of suds for the best performance. Follow the manufacturer's instructions to determine the
amount of detergent to use.
Use only HE High Efficiency detergent.
To fill dispenser compartments
1. Pull out the dispenser drawer.
2. Add the desired laundry product to the proper compartment.
3. Push in the dispenser drawer slowly and completely (to avoid a spill).
E
\
_3
Your new washer has a dispenser drawer with four separate compartments for your laundry
products--one is for detergent, one is for Oxi/co[or-safe bleach, one is for liquid chlorine
bleach, and one is for liquid fabric softener. I_aundry products are diluted and dispensed
automatically at the proper time during the wash cycle, making it unnecessary for you to
return to the washer during the cycle to add them.
It is normal for small amounts of water to remain in the dispensers when the wash cycle
is complete.
Do not put laundry products directly into the wash tub. Always use the proper dispensers
when adding laundry products.
Dispenser
A.Dispenser release lever
B.Oxi/Color-safe bleach compartment
C.Detergent type selector
D.H_,h Effk iency "HE" detergent compartment
E.Chlorine bleach compartment
l:_abric softener compartment
Oxi/Color-safe bleach compartment
(I.etter B in I)ispenser Illustration)
I.iquid or powdered oxygen based stain fighter/color-safe bleach may be used in this
compartment; however; powder is recommended for optimal timed release. Add your oxygen
based stain fighter/color-safe bleach to this compartment when using the Oxi Treat option.
The oxygen based stain fighter/color-safe bleach will automatically be dispensed during the
wash cycle if the Oxi Treat option is selected.
IMPORTANT: When delaying a cycle, use only powdered product in the Oxi/color-safe
bleach compartment because liquid product may seep out of the compartment during Delay
Wash, before the wash cycle begins.
High efficiency "HE" detergent compartment
(I.etter I) in Dispenser Illustration)
Add liquid or powdered HE detergent to this compartment for your wash cycle. The detergent
type selector (A) must always be in the correct position for the detergent type used. Slide the
detergent type selector to the correct position.
IMPORTANT:
• If you are using the Delay Wash option, powdered detergent should be used in the
compartment because liquid detergents may seep out of the compartment before the
wash begins.
• Use the detergent manufacturer's recommended amount for load size.
• I.iquid detergent:
• Powdered detergent:
Selector in position for powdered detergent
A. Detergent type selector
Chlorine bleach compartment
(I.etter E in Dispenser Illustration)
Add no more than 2/-4cup (160 ml.) liquid chlorine bleach to this compartment. The bleach
wi[[ be automatically diluted and dispensed at the best time during the first rinse after the
wash cycle. This compartment cannot dilute powdered bleach.
• Always measure liquid chlorine bleach. Use a measuring cup with a pour spout; do not
guess. Follow the manufacturer's directions for proper use.
• Do not fi[[ beyond the "MAX" [eve[. Overfilling could cause garment damage.
7:?
7!',',',i'i
Selector in position for liquid detergent
A. Detergent type selector
Fabric softener compartment
(I.etter F in Dispenser Illustration)
Pour measured liquid fabric softener into the fabric softener dispenser, if desired.
• I)o not overfill. The dispenser holds V4 cup (60 ml.).
• The fabric softener is dispensed in the rinse cycle. If Extra Rinse is selected,
the fabric softener will be dispensed during the Extra Rinse.
• I)o not use fabric softener dispensing balls in this washen Dispensing balls will not
operate correctly with this washen
• I)o not spill or drip any fabric softener onto the clothes.
• At the end of the cycle, a small amount of water may be left in the dispensen
This is normal.
NOTE: Use only liquid fabric softener in this dispenser.
1. To pause the washer at any time, select START/PAUSE.
2. To continue the cycle, select START/PAUSE (for approximately 1 second).
Vk: df e s
Not all Options and Modifiers are available with all cycles. Cycles, Options, and Modifiers
can be changed anytime before START/PAUSE is selected.
Options and Modifiers can be changed anytime after START/PAUSE is selected and bdore the
start of the selected Option or Modifier.
To cancel a cycle and begin a new cycle
1. Select POWER/CANCEl. twice.
2. Select desired cycle.
3. Select the desired OPTIONS.
4. Select START/PAUSE (for approximately 1 second) to restart the washer at the beginning
of the new cycle.
To cancel a cycle
1. Select POWER/CANCEl once.
2. The washer powers down, the door unlocks, and clothes can be removed.
NOTE: If the water [eve[ or the temperature is too high, the washer will drain automatically
before the door unlocks.
To change Options or Modifiers after the cycle has started
1. Select START/PAUSE once.
2. Select the desired OPTIONS or MODIFIERS.
3. Select START/PAUSE (for approximately 1 second) to continue the cycle.
To drain the washer manually
1. Select START/PAUSE once.
2. Select Drain&Spin.
3. Select START/PAUSE (for approximately 1 second) to begin the drain.
4. When the spin is complete, the door unlocks. Items can be removed from the washer.
Adding items
This washer allows an 8-minute period in which other garments may be added to the load.
You can add items to the washer if the status indicator shows Add Clothes.
To add items
1. Select START/PAUSE once. The washer door unlocks, and items can be added.
2. To continue the cycle, close the door and select START/PAUSE (for approximately
1 second).
3. To unlock the door after the Add Clothes period, press POWER/CANCEl twice.
This will cancel the Wash Cycle.
Cycle done
The cycle done indicator stays on for 60 minutes, until the door of the washer is opened,
or the Power/Cancel button is pressed.
Sanitize
Cycles certified by NSF International an independent, third party testing and certification
organization are those with the sanitize temperature selection available. The certification
verified that these cycles reduce 99.9% of bacteria typically found on clothing, bedding,
and towels. There is no carryover of bacteria between loads after the cycle is complete.
@
Certified to Sanitize
Locking controls
The Control I_ock avoids unintended use of the washer. You can also use the control lock
feature to avoid unintended cycle or option changes during a cycle. When Control I.ock light
is [it during a cycle, all buttons are disabled except for the Control I.ock, Power/Cancel, and
Start/Pause buttons.
To lock the controls
Select and hold CONTROl. lOCK button for 3 seconds.
This indicator shows which portion of the cycle the washer is operating and the estimated
time remaining. It also indicates when you can add an additional item to the wash cycle and
when the controls are locked.
estimated time remaining
sensing estimated time
delay add wash rinse spin done
clothes
16
Q
control lock
hold 3 seconds
The CONTROl_ I_OCKED status light illuminates.
To unlock the controls
Select and hold CONTROl. lOCK for 3 seconds until the Control I.ocked status light turns off.
Door Locked
When the status light illuminates, the door is locked.
Estimated time remaining
The cycle time varies automatically based on your water pressure, water temperature,
detergent, and clothes load. The cycle time will be extended if oversudsing occurs or the load
is unbalanced. The SUDs routine removes extra suds and assures proper rinsing of your
clothes. During the unbalance routine, the time displayed may pause until this activity is
complete, then resume with the cycle. These routines may add up to a half-hour to the default
cycle time.
Cycles can be selected by turning the Cycle control knob to the desired cycle. Each cycle
is designed for different types of fabric and soil levels.
delicate
uickwash
whitest
whites handwash
7_(_ WOOl
soal :lean washer
drain & spin Joor locked
rinse & spin
with_f_$h
press pause to unlock
Each cycle has a preset Soil Level (cycle time), Water Temperature, and Spin Speed, and
may have preset options. The preset settings provide the recommended fabric care for the
selected cycle.
The preset settings can be changed anytime before START is pressed. Not all options and
modifiers are available with all cycles. (To change settings after the cycle has started, press
PAUSE once, then select the desired settings. Press START again to continue the cycle.)
Whitest Whites
This cycle is especially designed for cleaning loads of soiled white fabrics with the addition of
bleach. Hot washing temperatures assure optimal bleach activity. An additional rinse provides
optimal rinse performance to avoid chlorine residues on your laundry. This cycle combines
speed tumbling, longer wash time, and fast-speed spin to shorten drying time.
Heavy Duty
Use this cycle to wash loads of sturdy, colorfast fabrics, and heavily soiled garments. This
cycle combines fast-speed tumbling, longer wash time, and extra high speed spin to shorten
drying times. If the water temperature is lower than needed for this cycle, the heater will
warm the water to the optimum temperature.
Normal/Casual
Use this cycle to wash normally soiled cottons and linens. This cycle combines medium-
speed tumbling and high-speed spin.
Quick Wash
Use this cycle to wash small loads of lightly soiled garments that are needed in a hurry. This
cycle combines fast-speed tumbling, a shortened wash time, and extra high speed spin to
shorten drying time.
Delicate
Use this cycle to wash no-iron fabrics and garments labeled "Permanent Press" or "Wrinkle
Free" or that indicate using a "Gentle" cycle on the care label. This cycle combines low-speed
tumbling and low-speed spin to help reduce wrinkling.
Wool
Use this cycle to clean machine washable woolen garments. Check the care instructions to
make sure that garment is washable. This cycle features gentle tumbling and low-speed spin
to provide optimum garment care.
Handwash
Use this cycle to clean hand washable and special-care garments. Similar to the way garments
are hand washed in a sink, the wash action of this cycle combines periods of low-speed
tumbling and soaking. I.ow-speed spin helps reduce wrinkling.
Soak
Use the Soak cycle to remove small spots of set-in stains on fabrics. This cycle provides a soak
time with warm or cold water followed by drain. Extra water, a short tumbling phase for equal
distribution of the laundry, and a soaking time without drum movement improve the removal
of set-in stains. Drain without spin assures gentle treatment, even for delicate articles.
Clean Washer Cycle
Use this cycle once a month to keep the inside of your washer fresh and clean. This cycle uses
a higher water [eve[ in combination with Affresh TM washer cleaner and steam, to thoroughly
clean the inside of your washer. This cycle should not be interrupted. See Cleaning Your
Washer in the Washer Care section.
IMPORTANT: Do not place garments in the washer during the Clean Washer cycle.
Rinse & Spin
Use this cycle to get a rinse and spin only. This cycle combines fast-speed tumbling and extra
high speed spin. If desired, you can reduce the spin speed by selecting the speed you want
from the Spin Speed modifier.
A Rinse & Spin cycle is useful for:
• I.oads that need rinsing only.
• Adding fabric softener to a load.
Drain & Spin
Use this cycle to drain your washer or to drain and spin your wash load. The spin speed is
preset to extra high. If desired, you can reduce the spin speed by selecting the speed you want
from the Spin Speed modifien
NOTE: I.oads of synthetics, delicate fabrics, hand washables, and washable woolens should
be drained with no spin or low spin speed to avoid fabric stress.
Loading...