MAYTAG MHWE300V User Manual

PERFORMANCE SERIES

FRONT-LOADING AUTOMATIC WASHER

USE & CARE GUIDE

LAVEUSE AUTOMATIQUE À CHARGEMENT FRONTAL

GUIDE D’UTILISATION ET D’ENTRETIEN

FOR QUESTIONS ABOUT FEATURES, OPERATION/PERFORMANCE, PARTS, ACCESSORIES OR SERVICE CALL: 1.800.688.9900 IN CANADA, CALL: 1.800.807.6777

AU CANADA, POUR ASSISTANCE, INSTALLATION OU SERVICE, COMPOSER LE : 1.800.807.6777

VISIT OUR WEBSITE AT WWW.MAYTAG.COM IN CANADA, WWW.MAYTAG.CA

OU VISITER NOTRE SITE INTERNET À WWW.MAYTAG.CA

461970255072 W10286177 B

Certified to Sanitize Certifié pour aseptiser

Designed to use only HE High Efficiency detergent Conçu pour l’utilisation d’un détergent haute efficacité seulement

TABLE OF CONTENTS

WASHER SAFETY ...................................................................................................................... 3

INSTALLATION REQUIREMENTS............................................................................................. 4

Tools and Parts.....................................................................................................................4

Options ................................................................................................................................ 5

Location Requirements......................................................................................................... 6

Drain System........................................................................................................................ 8

Electrical Requirements........................................................................................................ 8

INSTALLATION INSTRUCTIONS ............................................................................................. 9

Remove Transport System .................................................................................................... 9

Connect the Inlet Hoses ..................................................................................................... 10

Connect the Drain Hose..................................................................................................... 10

Secure the Drain Hose ....................................................................................................... 11

Level the Washer................................................................................................................11

Complete Installation ......................................................................................................... 11

FEATURES AND BENEFITS...................................................................................................... 12

WASHER USE.......................................................................................................................... 13

Starting Your Washer..........................................................................................................13

Using the Proper Detergent ................................................................................................ 13

Using the Dispenser ........................................................................................................... 14

Pausing or Restarting .......................................................................................................... 15

Changing Cycles, Options, and Modifiers ..........................................................................15

Status Indicator................................................................................................................... 16

Cycles.................................................................................................................................16

Options .............................................................................................................................. 18

Modifiers ............................................................................................................................ 18

LAUNDRY GUIDE .................................................................................................................. 19

LAUNDRY TIPS....................................................................................................................... 19

Loading .............................................................................................................................. 20

WASHER CARE........................................................................................................................20

Cleaning Your Washer ....................................................................................................... 20

Water Inlet Hoses...............................................................................................................21

Vacation, Storage, and Moving Care .................................................................................. 21

TROUBLESHOOTING.............................................................................................................22

ASSISTANCE OR SERVICE.......................................................................................................25

In the U.S.A........................................................................................................................ 25

In Canada........................................................................................................................... 25

WARRANTY ............................................................................................................................ 26

TABLE DES MATIÈRES

SÉCURITÉ DE LA LAVEUSE .....................................................................................................27

EXIGENCES D'INSTALLATION...............................................................................................29

Outillage et pièces.............................................................................................................. 29

Options ..............................................................................................................................29

Exigences d’emplacement ..................................................................................................30

Système de vidange............................................................................................................32

Spécifications électriques ................................................................................................... 32

INSTRUCTIONS D'INSTALLATION ....................................................................................... 33

Élimination des accessoires de transport ............................................................................ 33

Raccordement des tuyaux d’alimentation........................................................................... 34

Raccordement du tuyau de vidange...................................................................................34

Immobilisation du tuyau de vidange ..................................................................................35

Réglage de l'aplomb de la laveuse .....................................................................................35

Achever l’installation..........................................................................................................36

CARACTÉRISTIQUES ET AVANTAGES ...................................................................................36

UTILISATION DE LA LAVEUSE............................................................................................... 37

Mise en marche de la laveuse ............................................................................................38

Utilisation du détergent approprié...................................................................................... 38

Utilisation du distributeur................................................................................................... 39

Pause ou remise en marche...............................................................................................40

Changement des programmes, options et modificateurs ....................................................40

Témoins lumineux..............................................................................................................41

Programmes ....................................................................................................................... 41

Options ..............................................................................................................................43

Modificateurs ..................................................................................................................... 43

GUIDE DE LESSIVAGE ............................................................................................................ 44

CONSEILS DE LESSIVAGE....................................................................................................... 45

Chargement........................................................................................................................ 45

ENTRETIEN DE LA LAVEUSE................................................................................................... 46

Nettoyage de la laveuse .....................................................................................................46

Tuyaux d'arrivée d'eau....................................................................................................... 47

Précautions à prendre avant les vacances,

un entreposage ou un déménagement................................................................................ 47

DÉPANNAGE .......................................................................................................................... 48

ASSISTANCE OU SERVICE...................................................................................................... 52

Aux États-Unis....................................................................................................................52

Au Canada ......................................................................................................................... 52

GARANTIE...............................................................................................................................53

WASHER SAFETY

You

You can be killed or seriously injured if you don't immediately

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. The parts supplied are in the washer drum.

Tools needed for connecting the water inlet hoses

 Pliers (that open to 1

/16" [39.5 mm])

 Flashlight (optional)

Tools needed for connecting the drain hose

 Locking pliers (that open to 1

/16" [39.5 mm])

Tools needed for installation

 Open end wrenches 17 mm and 13 mm  Level  Wood block  Ruler or measuring tape

Parts supplied:

A. Drain hose form B. Inlet hose (2)

C. Inlet hose washers (4) D. Transport bolt hole plug (4) E. Beaded strap

F. Drain hose

G. Hose clamp

Alternate Parts

Your installation may require additional parts. If you are interested in purchasing one of the items listed here, call the toll-free number on the cover or in the “Assistance or Service” section.

If You Have You Will Need to Buy

Laundry tub or standpipe t

aller than 96" (2.4 m)

Sump pump system (if not already available)

Overhead sewer Standard 20 gal. (76 L), 30" (762 mm) tall drain tub or

utility sink and sump pump (available from local plumbing suppliers)

Floor drain Siphon break, Part Number 285834; additional drain hose

r t Number 8318155; and connector kit, Part

mber

285835

Drain hose too short 4 ft (1.2 m) drain hose extension kit, Part Number 285863

Water faucets beyond reach of fil

l hoses

2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314, 10 ft (3.0 m) Part Number 350008

Options

Pedestal

A pedestal will add to the total height of the washer for a total height of 53.5" (1359 mm).

Optional pedestal

This pedestal is available in several colors. To order, call the dealer from whom you purchased your washer or refer to the “Assistance

or Service” section.

Pedestal Height Color Part Number

10" (254 mm) White MHP1000SQ

10" (254 mm) Black

MHP1000SB

15.5" (394 mm) White XHP1550VW

15.5" (394 mm) Black

XHP1550VB

15.5" (394 mm) Slate XHP1550VE

15.5" (394 mm) Crimson Red

XHP1550WR

15.5" (394 mm) Oxide XHP1550VJ

15.5" (394 mm) Evergreen XHP1550VP

Stack Kit

Are you planning to stack your Maytag washer and dryer? To do so you will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your dryer or refer to the “Assistance or Service” section. Ask for Part Number 8212640.

Location Requirements

Selecting the proper location for your washer improves performance and minimizes noise and possible washer “walk.”

Your washer can be installed under a custom coun

ter, or in a basement, laundry room, closet,

or recessed area. See “Drain System.” Companion appliance location requirements should als

o be considered. Proper installation is

your responsibility.

You will need

 A water heater set to deliver 120°F (49°C) water to the washer.  A grounded electrical outlet located within 6 ft (1.8 m) of where the power cord is

attached to the back of the washer. See “Electrical Requirements.”

 Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves,

and water pressure of 20-100 psi (137.9-689.6 kPa).

 A level floor with a maximum slope of 1" (25 mm) under entire washer. Installing the

washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not recommended.

 A sturdy and solid floor to support the washer with a total weight (water and load) of

400 lbs (180 kg).

Do not operate your washer in temperatures below 3

2°F (0°C). Some water can remain in the

washer and can cause damage in low temperatures.

Installation clearances

 The location must be large enough to allow the washer door to be fully opened.  Additional spacing should be considered for ease of installation and servicing.  Additional clearances might be required for wall, door, and floor moldings.  Additional spacing of 1" (25 mm) on all sides of the washer is recommended to reduce

noise transfer.

 Companion appliance spacing should also be considered.

Washer Dimensions

(686 mm)

/2"

(1335 mm)

/2"

(820 mm)

/4"

(970 mm)

Recommended installation spacing for custom undercounter installation

The dimensions shown are for the recommended spacing.

Custom undercounter installation - Washer only

(25 mm)

39" min.

(990 mm)

27"

(686 mm)

Recommended installation spacing for recessed or closet installation, with or without a pedestal

The dimensions shown are for the recommended spacing.

Recessed area or closet installation

34" (864 mm)

(76 mm)

48 in.

(310 cm2)

24 in.

(155 cm2)

(25 mm)

(102 mm)

31½"

(800 mm)

A. Side view - closet or confined area B. Closet door with vents

*Required spacing

Recessed or closet installation - Washer on pedestal

(25 mm)

31½"

(800 mm)

(25 mm)

27"

(686 mm)

(102 mm)

18" min.

(457 mm)

A. Recessed area B. Side view - closet or confined area

Recommended installation spacing for recessed or closet installation, with stacked washer and dryer

The dimensions shown are for the recommended spacing.

48 in.2 *

(310 cm2)

3"* (76 mm)

1"* (25 mm)

24 in.

(155 cm

)

*Required spacing

6"* (152 mm)

76"

(1930 mm)

27"

(686 mm)

(25 mm)

5½"**

(140 mm)

*Required spacing

**For venting out the side, 1" (25 mm) spacing is allowed.

Recommended installation spacing for cabinet installation

 The dimensions shown are for the recommended spacing.  For cabinet installation, with a door, the minimum ventilation openings in the top are

required.

7" (178 mm)

9" (229 mm)

7" (178 mm)

(102 mm)

31½"

(800 mm)

27"

(686 mm)

(25 mm)1"(25 mm)1"(25 mm)

Drain System

The washer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See “Tools and Parts.”

Standpipe drain system - wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of 2" (50 m). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute.

The top of the standpipe must be at least 30" (762 m) high and no higher than 96" (2.4 m) from the bottom of the washer.

30" min.

(762 mm)

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 30" (762 mm) above the floor.

Floor drain system (view D)

The floor drain system requires a siphon break that may be purchased separately. See “Tools and Parts.”

The siphon break must be a minimum of 28" (710 mm) from the bottom of the washer. Ad

ditional hoses might be needed.

30" min.

(762 mm)

28" min.

(710 mm)

Electrical Requirements

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

re, or electrical shock.

WARNING

 A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. Time-

delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this washer be provided.

 This washer is equipped with a power supply cord having a 3 prong grounding plug.  To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong,

grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician.

 If codes permit and a separate ground wire is used, it is recommended that a qualified

electrician determine that the ground path is adequate.

 Check with a qualified electrician if you are not sure the washer is properly grounded. .

INSTALLATION INSTRUCTIONS

Remove Transport System

WARNING

Excessive Weight Hazard Use two or more people to move and install washer. Failure to do so can result in back or other injury.

IMPORTANT: Position the washer so that the rear of the washer is within approximately 3 ft (900 mm) of its final location.

There are 4 bolts in the rear panel of the washer that support the suspension system during tr

ansportation. These bolts also retain the power cord inside the washer until the bolts are

removed.

1. Using a 13 mm wrench, loosen each of the bolts.

2. Once t

he bolt is loose, move it to the center of the hole and completely pull out the bolt,

including the plastic spacer covering the bolt.

3. Once all 4 bolts are removed, discard bolt and spacers. Then pull the power cord through

the opening of the rear panel and close the hole with the attached cap.

4. Close the bolt holes with the 4 transport bolt hole plugs. NOTE: If the washer is to be transported at a later date, call your local service center. To avoid

suspension and structural damage to your washer, it must be properly set up for relocation by a certified technician.

Connect the Inlet Hoses

1. Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers

in the couplings.

A. Coupling B. Washer

2. Make sure the washer drum is empty.

3. Att

ach the hose with the red color indicator to the Hot (left) inlet valve. Attaching the red coupling first makes it easier to tighten connection with pliers. Screw on coupling by hand until it is seated on the washer.

4. Att

ach the hose with the blue color indicator to the Cold (right) water inlet valve. Screw on coupling by hand until it is seated on the washer.

H. Hot water inlet

C. Cold water inlet

5. Using pliers, check the tightness of the hose couplings already attached to the washer. NOTE:

Do not overtighten. Damage to the coupling can result.

6. Attac

h hot water hose to the hot water faucet. Screw on coupling by hand until it is seated

on the washer.

7. Att

ach cold water hose to the cold water faucet. Screw on coupling by hand until it is

seated on the washer.

8. Using pliers, tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling can result.

9. T

urn on the water faucets and check for leaks.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or

replacement dates on the hoses for future reference.

10. Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

Connect the Drain Hose

Remove drain hose from washer drum

1. Use

locking pliers, squeeze hose clamp tabs together and insert over the end of drain

hose.

2. Slide drain hose onto washer connection.

3. Once drain hose is in place, release pliers.

4. W

asher drain system can be installed using a floor drain, wall standpipe, floor standpipe,

or laundry tub.

Laundry tub drain or standpipe drain

Connect the drain hose form to the corrugated drain hose.

A. Snap either end of the drain hose form to the drain hose at the

point where the corrugation begins.

B. Bend drain hose over drain hose for

m and snap into place.

To keep drain water from going back into the washer:

 Do not straighten the drain hose, and do not force excess drain hose into standpipe.

Hose should be secure, but loose enough to

provide a gap for air.

 Do not lay excess hose on the bottom of the laundry tub.

Floor drain

You may need additional parts. See Floor drain under “Tools and Parts.”

Secure the Drain Hose

1. Drape the power cord over the washer top.

2. Sec

ure the drain hose to the laundry tub leg or standpipe with the beaded strap provided.

(See illustrations A and B).

AB C

If the washer faucets and the drain standpipe are recessed (see illustration C), put the hooked end of the drain hose in the standpipe. Tightly wrap the beaded strap around the water inlet hoses and the drain hose.

Do not force excess drain hose into the standpipe.

Level the Washer

Properly leveling your washer avoids excessive noise and vibration.

1. Check the levelness of the washer by placing a level on the top edge of the washer, first

side to side, then front to back.

If the washer is against a wall, move the washer out slightly before tipping back. If the washer is not level, first prop the front with a wood block and adjust the feet as necessary; then prop the back and adjust feet as necessary. Repeat this step until washer is level.

2. Make sure a

ll four feet are stable and resting on the floor. Then check that the washer is

perfectly level (use a level).

3. After the

washer is level, use a 17 mm open-end wrench to turn the nuts on the feet tightly

against the washer cabinet. IMPORTANT: All four feet must be tightened. If the nuts are not tight against the washer

cabinet, the washer may vibrate.

4. T

he washer should not move front to back, side to side, or diagonally when pushed on its

top edges.

5. Sli

de the washer to its final location.

6. Confirm

the levelness of the washer.

Complete Installation

1. Check the electrical requirements. Be sure that you have the correct electrical supply and

the recommended grounding method. See “Electrical Requirements.”

2. Check that all parts are now installed. If there is an extra part, go back through the steps to

see which step was skipped.

3. Chec

k that you have all of your tools.

4. Dispose of/rec

ycle all packaging materials.

5. Check that the water faucets are on.

6. Check for leaks around faucets and inlet hoses.

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

re, or electrical shock.

WARNING

7. Plug into a grounded 3 prong outlet.

8. Read “W

asher Use.”

9. T

o test and clean your washer, make sure there are no clothes in the washer and add one AFFRESH™ tablet to the washer drum. Select POWER/CANCEL, the Clean Washer cycle, and then select START/PAUSE. This cycle will take approximately 50 minutes to complete. Allow the washer to complete the entire Clean Washer Cycle without interruption.

FEATURES AND BENEFITS

Electronic Controls

Flexible electronic controls are easy to use whether, you are a beginner or an expert.

Smart Dispensers

The Smart Dispensers make your washer truly automatic. This washer provides a threecompartment dispenser which includes separate compartments for main wash detergent, fabric softener, and chlorine bleach. The dispenser has large pour zones. The dispenser is self-cleaning, and can be easily removed. Laundry produ

cts are diluted with fresh water and

added to the load at the proper time in the wash cycle.

Clean Washer with AFFRESH™ Cycle

This cycle uses steam to raise the temperature of the unit and makes the washer self-cleaning, flushing the machine’s interior free of dirt and other residue. The use of AFFRESH™ washer cleaner or liquid chlorine bleach with this cycle will remove and help avoid odor-causing residue.

Auto Water Level

This washer automatically adjusts water level for optimal cleaning and rinsing performance. Two sensors determine load size, load composition, and suds level, then the sensors adjust the water level to the proper setting. This eliminates guesswork. The water level is just right for every wash load size.

Super Size Capacity

Since there is no agitator, you can wash larger, bulkier items such as a king-sized bedspread. You are also able to wash more clothes at one time, which means fewer loads.

Smooth Balance™ Balance System

To reduce washer “walk” and “off-balance” conditions, your new washer combines:

 2 Springs to isolate vibration  4 Shock absorbers at the washer base to minimize movement

Commercial Quality Stainless Steel Drum

The commercial quality stainless steel drum eliminates corrosion and enables higher spin speeds for more water extraction, reducing drying time compared to traditional front-load washers.

High-Efficiency Wash System

Your new front-loading, high-efficiency washer saves time with fewer, larger loads, and lowers your water and energy bills by helping conserve resources.

Spin Speeds

This washer automatically selects the spin speed based on the cycle selected. This factory setting can be changed, however. This washer offers up to five different spin speed choices.

Heating Element

This washer has a heating element that automatically heats the water to the optimal temperature on select cycles. This enables stepped cleaning, a process in which warm water is brought in and mixed with detergent first, then the water is heated. Stepped cleaning starts the wash cycle with warm water to help remove stains (such as blood and grass). This heater is active in the Whitest Whites, Heavy Duty, Normal/Casual, and Power Wash cycles.

Automatic Temperature Control

The automatic temperature control electronically senses and maintains a uniform water temperature. Automatic temperature control regulates incoming hot and cold water. Automatic temperature control is automatically turned on when a cycle is selected.

Add Clothes

Clothes can be added to the load during the first 8 minutes of the cycle. During this time, the Status Indicator will indicate it is okay to add clothes.

Special Cleaning Action with Sensi-Care™ Wash System

This washer channels 100% of the water through the dispensers to assure thorough rinse-out and mixture of all the laundry products before they touch any garments. The water is then sprayed from the top front onto the center of the load, providing even distribution, and optimum cleaning performance. It is normal for small amounts of water to remain in the dispensers when the wash cycle is complete.

Efficient Detergent System

This washer has a specially designed valve that closes during the wash portion of the cycle so that 100% of the water and detergent mixture

is used on the load. The Efficient Detergent

System ensures that no water or detergent is wasted.

Dynamic Off-Balance Detection

This washer uses two sensors to detect load size and the amount of off-balance within the load. The suspension system and controls are specially designed to redistribute the load automatically.

WASHER USE

NOTE: The panel shown above may be different from that of your model.

Starting Your Washer

WARNI NG: To reduce the risk of fire, electric shock, or injury to persons, read the

IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. The following is a guide to using your washer. Please refer to specific sections of this manual

for more detailed information. Do not store laundry products on

the top surface of this washer. Vibration is normal during

operation.

Using the Proper Detergent

Use only High Efficiency detergents. The package for this type of detergent will be marked “HE” or “High Efficiency.” This wash system, along with less water, will create too much sudsing with a regular non-HE detergent. Using regular detergent will likely result in washer errors, longer cycle times, and reduced rinsing performance. It may also result in component failures and noticeable mold or mildew. HE detergents are made to produce the right amount of suds for the best performance. Follow the manufacturer’s instructions to determine the amount of detergent to use. Remember, concentrated detergents such as 2x or higher will use less detergent based on load size.

Use only HE High Efficiency detergent.

First Wash Cycle Without Laundry

Before washing clothes for the first time, if not completed during the final installation step, choose the Normal/Casual cycle and run it without clothes. Use only HE High Efficiency detergent. Use 1/2 the manufacturer’s recommended amount for a medium-size load. This initial cycle serves to ensure the interior is clean before washing clothes.

For All Wash Cycles

1. Open the washer door by pulling on the handle. Sort laundry according to color and type

of fabric. Place a load of sorted clothes in the washer. Do not overload washer. Overloading can cause poor cleaning.



The washer can be fully loaded, but not tightly packed. Washer door should close easily.

 Mix large and small items and avoid washing single items. Load evenly.



It is recommended that you wash small items such as infant socks in a mesh garment bag.

 When unloading garments, occasionally check under the gray colored seal at the

front of the tub for small items.

2. Close the washer door by pushing it firmly until the lock clicks. The washer door will

remain locked during the wash cycle. NOTE: After any wash cycle is completed, the door must be opened and then closed

before a new cycle can begin. The door can be opened only if START/PAUSE or POWER/ CANCEL is selected while the status indicator is in the Add Clothes area or if the cycle has been canceled. See “To cancel a cycle” in Changing Cycles, Options, and Modifiers section.

3. Open the dispenser drawer and add laundry products to the main wash detergent,

chlorine bleach, or fabric softener compartments. Close drawer slowly to avoid spills. See “Using the Dispenser.”

4. T

urn on the washer by selecting POWER/CANCEL. Select one of the cycles by turning the cycle selector. The indicator light for the selected cycle will illuminate. When selecting a wash cycle, the preset Options, Wash Temp, Spin Speed, and Soil Level for the selected cycle will illuminate. The display shows the estimated time remaining. The preset settings provide the recommended fabric care for the selected cycle. See “Cycles.”

5. Selec

t the desired Options, such as Max ExtractTM, Extra Rinse, and Soak Time. Not all

options are available with all cycles. See “Options.”

6. Selec

t the desired Modifiers, such as Soil Level, Wash Temp, and Spin Speed. Not all

modifiers are available with all cycles and options. See “Modifiers.”

7. If desired, select SIGNAL ON/OFF. The signal is helpful when you are washing items that

should be removed from the washer as soon as it stops.

8. To begin the wash cycle immediately

Select START/PAUSE.

 If you do not select START/PAUSE within 60 minutes of choosing a cycle, the washer

automatically shuts off.

 When the wash cycle is complete, the status indicator shows Done, the door unlocks,

and the wash load can be removed from the washer. The washer powers down automatically 5 minutes after the cycle is complete. To power down the washer manually after the wash cycle is complete, select POWER/CANCEL once.

Using the Dispenser

Your new washer has a dispenser drawer with three separate compartments for your laundry products—one is for detergent, one is for liquid chlorine bleach, and one is for liquid fabric softener. Laundry products are diluted and dispensed automatically at the proper time during the wash cycle, making it unnecessary for you to return to the washer during the cycle to add them.

It is normal for small amounts of water to remain i

n the dispensers when the wash cycle

is complete. Do not put laundry products directly into the wash tub. Always use the proper dispensers

when adding laundry products.

Choosing the Right Detergent

Use only HE High Efficiency detergent.

To fill dispenser compartments

1. Pull out the dispenser drawer.

2. Add the desired laundry product to the proper compartment.

3. Push in

the dispenser drawer slowly and completely (to avoid a spill).

Dispenser

A. Detergent type selector

B. Main wash compartment

C. Dispenser release lever

Chlorine bleach compartment

E. Fabric softener compartment

Main wash compartment

(Letter B in Dispenser Illustration) Add liquid or powdered HE detergent to this compartme

nt for your wash cycle. The detergent type selector (A) must always be in the correct position for the detergent type used. Slide the detergent type selector to the correct position.

IMPORTANT:

 Liquid or powdered color-safe bleach may be added to the Main Wash compartment

along with the same type of liquid or powdered detergent.

 Use the detergent and color-safe bleach manufacturer’s recommended amount for

load size.

 If you are using the Delay Wash option, powdered laundry products should be used

in the main wash compartment because liquid products may seep out of the compartment before the main wash begins.

 Liquid detergent:

LIQUI

Selector in position for liquid detergent

A. Detergent type selector



Powdered detergent:

LIQUI

Selector in position for powdered detergent

A. Detergent type selector

Chlorine bleach compartment

(Letter D in Dispenser Illustration) Add no more than

/3 cup (160 mL) liquid chlorine bleach to this compartment. The bleach

will be automatically diluted and dispensed at the best time during the first rinse after the wash cycle. This compartment cannot dilute powdered bleach.

 Always measure liquid chlorine bleach. Use a measuring cup with a pour spout; do not

guess. Follow the manufacturer’s directions for proper use.

 Do not fill beyond the “MAX” level. Overfilling could cause garment damage.

Fabric softener compartment

(Letter E in Dispenser Illustration) Pour measured liquid fabric softener into the fabric softener dispenser, if desired. NOTES:

 Pour only liquid fabric softener into the dispenser.  Do not overfill. The dispenser holds

/4 cup (60 mL).

 The fabric softener is dispensed in the rinse cycle. If Extra Rinse is selected,

the fabric softener will be dispensed during

the Extra Rinse.

 Do not use fabric softener dispensing balls in this washer. Dispensing balls will not

operate correctly with this washer.

 Do not spill or drip any fabric softener onto the clothes.  At the end of the cycle, a small amount of water may be left in the dispenser.

This is normal.

Pausing or Restarting

1. To pause the washer at any time, select START/PAUSE.

2. To continue the cycle, select START/PAUSE (for approximately 1 second).

Changing Cycles, Options, and Modifiers

Not all Options and Modifiers are available with all cycles. Cycles, Options, and Modifiers can be changed anytime before START/PAUSE is selected.

Options and Modifiers can be c

hanged anytime after START/PAUSE is selected and before

the start of the selected Option or Modifier.

To cancel a cycle and begin a new cycle

1. Select PO

WER/CANCEL twice.

2. Select desired cycle.

3. Select the desired OPTIONS.

4. Select S

TART/PAUSE (for approximately 1 second) to restart the washer at the beginning

of the new cycle.

To cancel a cycle

1. Select PO

WER/CANCEL once.

2. T

he washer powers down, the door unlocks, and clothes can be removed.

NOTE: If the

water level or the temperature is too high, the washer will drain automatically

before the door unlocks.

To change Options or Modifiers after the cycle has started

1. Selec

t START/PAUSE once.

2. Selec

t the desired OPTIONS or MODIFIERS.

3. Selec

t START/PAUSE (for approximately 1 second) to continue the cycle.

To drain the washer manually

1. Select START/PAUSE once.

2. Select DRAIN/SPIN.

3. Selec

t START/PAUSE (for approximately 1 second) to begin the drain.

4. When the spin i

s complete, the door unlocks. Items can be removed from the washer.

Status Indicator

This indicator shows which portion of the cycle the washer is operating and the estimated time remaining. It also indicates when you can add an additional item to the wash cycle and when the controls are locked.

Adding items

This washer allows an 8-minute period in which other garments may be added to the load. You can add items to the washer if the status indicator shows Add Clothes.

To add items

1. Selec

t START/PAUSE once. The washer door unlocks, and items can be added.

2. To continue the cycle, close the door and select START/PAUSE (for approximately

1 second).

3. To unlock the door after the Add Clothes period, press POWER/CANCEL twice.

This will cancel the Wash Cycle.

Cycle done

The cycle done indicator stays on for 60 minutes, until the door of the washer is opened, or the Power/Cancel button is pressed.

Locking controls

The Control Lock avoids unintended use of the washer. You can also use the control lock feature to avoid unintended cycle or option changes during a cycle. When Control Lock light is lit during a cycle, all buttons are disabled except for the Control Lock, Power/Cancel, and Start/Pause buttons.

To lock the controls

Select and hold CONTROL LOCK button for 3 seconds.

The CONTROL LOCK status light illuminates.

To unlock the controls

Select and hold CONTROL LOCK for 3 seconds until the Control Lock status light turns off.

Door Locked

When the status light illuminates, the door is locked.

Estimated time remaining

The cycle time varies automatically based on your water pressure, water temperature, detergent, and clothes load. The cycle time will be extended if oversudsing occurs or the load is unbalanced. The SUDs routine removes extra suds and assures proper rinsing of your clothes. During the unbalance routine, the time displayed may pause until this activity is complete, then resume with the cycle. These routines may add up to a half-hour to the default cycle time.

Cycles

Cycles can be selected by turning the Cycle control knob to the desired cycle. Each cycle is designed for different types of

fabric and soil levels.

 Each cycle has a preset Soil Level (cycle time), Water Temperature, and Spin Speed, and

may have preset options. The preset settings provide the recommended fabric care for the selected cycle.

 The preset settings can be changed anytime before START is pressed. Not all options and

modifiers are available with all cycles. (To change settings after the cycle has started, press PAUSE once, then select the desired settings. Press START again to continue the cycle.)

Whitest Whites

This cycle is especially designed for cleaning loads of soiled white fabrics with the addition of bleach. Hot washing temperatures assure optimal bleach activity. An additional rinse provides optimal rinse performance to avoid chlorine residues on your laundry. This cycle combines high-speed tumbling, longer wash time, and fast-speed spin to shorten drying time.

Heavy Duty

Use this cycle to wash loads of sturdy, colorfast fabrics and heavily soiled garments. This cycle combines fast-speed tumbling, optimal wash time, and extra high speed spin to shorten drying times. If the water temperature is lower than needed for this cycle, the heater will warm the water to the optimum temperature.

Normal/Casual

Use this cycle to wash normally soiled cottons and linens. This cycle combines mediumspeed tumbling and high-speed spin.

Delicate

Use this cycle to wash no-iron fabrics and garments labeled “Permanent Press” or “Wrinkle Free” or that indicate using a “Gentle” cycle on the care label. This cycle combines low-speed tumbling and low-speed spin to help reduce wrinkling.

Quick Wash

Use this cycle to wash small loads of lightly soiled garments that are needed in a hurry. This cycle combines fast-speed tumbling, a shortened wash time, and extra high speed spin to shorten drying time.

Sanitary

Cycles certified by NSF International, an independent, third party testing and certification organization are those with the sanitize temperature selection available. The certification verified that these cycles reduce 99.9% of bacteria typically found on clothing, bedding, and towels. There is no carryover of bacteria between loads after

the cycle is complete.

Certified to Sanitize

Use this cycle to clean heavily soiled, colorfast fabrics. This cycle combines a super hot water temperature and fast-speed tumbling to help ensure the removal of heavy soils and stains. It is recommended that you set your hot water heater to 120°F (49°C) to ensure proper performance during this cycle. Extra high speed spin helps shorten drying time. Only Sanitary cycle has been designed to meet the requirements of NSF Protocol P172 for Sanitizing Efficacy.

Power Wash

Use this cycle to wash small loads of heavily soiled work wear such as, overalls, coveralls, sweatshirts, pants, and outdoor garments. This cycle combines warm water temperature, optimal rinses, and a longer cycle time to help ensure the removal of all soil and stains from your laundry.

Clean Washer with AFFRESH™

Use this cycle once a month to keep the inside of your washer fresh and clean. This cycle uses a higher water level in combination with AFFRESH

washer cleaner or bleach and steam, to thoroughly clean the inside of your washer. This cycle should not be interrupted. See Cleaning Your Washer in the Washer Care section.

IMPORTANT: Do

not place garments in the washer during the Clean Washer cycle.

Rinse & Spin

Use this cycle to get a rinse and spin only. This cycle combines fast-speed tumbling and extra high speed spin. If desired, you can reduce the spin speed by selecting the speed you want from the Spin Speed modifier.

A Rinse & Spin cycle is

useful for:

 Loads that need rinsing only, like swimsuits.

NOTE: F

or more delicate loads, when using a Rinse & Spin cycle to rinse swimwear,

change the Speed Spin Modifier setting to Medium or Low to avoid fabric stress.

 Adding fabric softener to a load.

Drain & Spin

Use this cycle to drain your washer or to drain and spin your wash load. The spin speed is preset to extra high. If desired, you can reduce the spin speed by selecting the speed you want from the Spin Speed modifier.

NOTE: Lo

ads of synthetics, delicate fabrics, hand washables, and washable woolens should

be drained with no spin or low spin speed to avoid fabric stress.

Preset cycle settings

Each cycle has a preset Soil Level (cycle time), Water Temperature, and Spin Speed. The preset settings provide the recommended fabric care for the selected cycle. See chart.

Cycles Soil Level

(cycle time)

Water Temp

Spin Speed

Whitest Whites Normal

(1:20)

Hot/Cold Extra High

Heavy Duty Heavy

(1:20)

Warm/Cold Extra High

Normal/Casual Normal

(0:50)

Warm/Cold High

Delicate Normal

(0:40)

Cold/Cold Low

Quick Wash (2-3 Items)

Light (0:30)

Warm/Cold Extra High

Sanitary Normal

(1:50)

Hot/Cold High

Power Wash Heavy

(1:55)

Hot/Cold Extra High

Clean Washer with AFFRESH™

N/A (1:05)

N/A

Rinse & Spin N/A

(0:20)

Cold/Cold Extra High

Drain & Spin N/A

(0:11)

N/A Extra High

To change the preset cycle settings

Press the selector of each setting unt

il the desired setting illuminates.

Normal Washer Sounds

As with any new product, you will hear sounds that you are not accustomed to. You may hear various sounds when the door is locked and unlocked, and during the washing, rinsing, and spinning process. Between changes in wash actions, there will be momentary pauses. You will hear water spraying and splashing during the wash and rinse cycles. These new sounds and pauses are part of normal washer operation.

+ 39 hidden pages

MAYTAG MHWE300V User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual