Maytag MHWC7500Y User Manual
PRODUCT MODEL NUMBERS
(990 mm)
MHWC7500Y
Front-Loading Automatic Washer
Washer Dimensions: Undercounter installation -
7
23
16"
/
(595 mm)
327/8"
(835 mm)
Recessed area or closet installation -
without pedestal
3"
9"
34"
(229 mm)
(864 mm)
(76 mm)
48 in.
(310 cm2)
washer only:
1
/4""
36
(920 mm)
1
20
/8"
(510 mm)
Recessed area or closet installation -
with pedestal
9"
2
18"
(229 mm)
(457 mm)
3"
(76 mm)
48 in.
(310 cm2)
Cabinet installation:
1"
(25 mm)
Custom cabinet installation
7"
(178 mm)
2
1"
(25 mm)
(229 mm)
(229 mm)
39" min.
9"
9"
2
24 in.
4"
(102 mm)
1"
(25 mm)
1"
(25 mm)
(76 mm)
(155 cm2)
3"
*External exhaust elbow requires additional space.
Recessed or closet installation stacked washer and dryer
12"
(305 mm)
3"
1
/4"
5
(133 mm)
1"
(25 mm)
653/4"
(1670 mm)
1"
(25 mm)
(76 mm)
3"
(76 mm)
48 in.
(310 cm2)
24 in.
(155 cm2)
2
2
4411/16"
4411/16"
(1135 mm)
(1135 mm)
2
4"
(102 mm)
1"
(25 mm)
1"
(25 mm)
3"
(76 mm)
24 in.
(155 cm2)
4"
(102 mm)
Installation spacing for recessed area or closet installation
The dimensions shown below are the recommended spacing for this washer.
■ Additional spacing should be considered for ease of installation and servicing.
■ Additional clearances might be required for wall, door, oor moldings, and dryer
venting.
■ Additional spacing of 1" (25 mm) on all sides of the dryer is recommended to
reduce noise transfer.
■ For closet installation, with a door, minimum ventilation openings in the top and
bottom of the door are required.
Louvered doors with equivalent ventilation openings are acceptable. Companion
appliance spacing should also be considered.
1"
(25 mm)
W10445545B
1"
(25 mm)
02/2012
ELECTRICAL REQUIREMENTS
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is
recommended that a separate circuit serving only this appliance be provided.
DRAIN SYSTEM
Drain system can be installed using a oor drain, wall standpipe,
oor standpipe, or laundry tub. Select method you need.
IMPORTANT: To avoid siphoning, only 4
hose should be inside standpipe. Always secure drain hose with
cable tie.
1
⁄2" (114 mm) of drain
Floor standpipe drain system
Laundry tub drain system
Minimum capacity: 20 gal. (76 L). Top of laundry tub must
be at least 30" (762 mm) above oor; install no higher than
55" (1.4 m) from bottom of washer.
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. A 1/4" (6 mm)
diameter to 1" (25 mm) diameter Standpipe Adapter Kit is
available (Part Number 3363920). Top of standpipe must be at
least 30" (762 mm) high; install no higher than 55" (1.4 m) from
bottom of washer. If you have an overhead sewer and need to
pump higher than 96 inches, a sump pump and associated
hardware are needed. See “Alternate Parts”.
Wall standpipe drain system
See requirements for oor standpipe drain system.
Floor drain system
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. See “Alternate Parts”. Minimum siphon
break height: 28" (710 mm) from bottom of washer. (Additional
hoses may be needed.)
Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation
our products, we reserve the right to change materials and specications without notice. Instructions packed with product. Specications subject to change without notice.
Loading...