Maytag mhw19xxaww, mhw19xxagw, mah7550agw, mah7500bww, mah7500bwq Instruction Sheet

...

Instruction Sheet

Locking

Nut

Replace

required

Seal Tool

Grommet

Replace if

required

Washer

Kit

“O”Ring

Lip

Seal

16021976 Instruction

Sheet

WARNING

5. 35-2968 Spanner (Used for leverage to remove rear pulley).

6. Torque Wrench

7. T-20 Torx™ Driver

1. Disconnect power to the machine.

2. Remove the front panel, top cover, front shroud and shroud support brackets.

Spinner Support Assembly

Kit Includes:

Molykote Grease Spinner Support Assy Locking Nut - Replace if required Seal Tool Grommet - Replace if required Washer Kit “O” Ring Lip Seal Instruction Sheet

Explanation:

The spinner tub support attaches to the spin basket and the spinner support extends through a seal system to the exterior of the outer tub, with a pulley attached to the end of the shaft. This assembly supports the spin basket and transfers the rotation of the drive pulley directly to the rotation of the spin basket.

NOTE: Whenever the spinner tub support is removed, replacement of the shaft seal system should be performed.

Tools:

1. 5/16” Nut Driver

2. 9/16”, 1/2” Socket and Ratchet

3. Phillips Screw Diver

4. Flat Blade Screw Driver

5. 35-2968 Spanner (Used for leverage to remove rear pulley).

6. Torque Wrench

7. T-20 Torx™ Driver -

WARNING

†

1. Disconnect power to the machine.

2. Remove the front panel, top cover, front shroud and shroud support brackets.

Electrical Shock

Hazard Disconnect power before servicing. Replace all parts and panels before

operating.

Failure to do so can result in death or electrical shock.

3. Remove Shroud Support Brackets.

4. Remove the Outer Tub Cover. a. If the washer has a heater installed into the tub cover,

remove the wires from the tub cover and the wire retainer screws.

b. Usingaatbladedscrewdriver,slide the screwdriver

under the clip and pry to remove the clip. Remove the remaining clips from the outer tub cover.

c. Gently remove the cover from the outer tub.

† - ®TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

Instruction Sheet W11086225 Rev. A 1/17

— 1 —

(continued)

5. Remove Drive Pulley by standing over top of washer, while

wire retainer screws.

Remove the remaining clips from the outer tub cover.

Wrench

11. Slide “O”-Ring onto the new shaft and fully seat onto the base of the Spinner Support. Apply Molykote grease on spinner shaft. Spread grease thin on shaft to avoid excess from getting into next wash load.

11. Slide “O”-Ring onto the new shaft and fully seat onto the base of the Spinner Support. Apply Molykote

grease on spinner shaft. Spread grease thin on shaft to avoid excess from getting into next wash load.

“O”-Ring

Apply Molykote Along Shaft

Fully seated O-Ring

12. Reinstall the 3 plastic washers on Spinner. Assemble the Spinner and Spinner Support Shaft. Position

the Spinner with Spinner Support shaft into the Outer Tub.

13. Install the Drive Pulley onto the Spinner Support Shaft. Replace the tabbed pulley washer with new 1-

1/4” washer along with the new retaining bolt. Tighten retaining bolt to 33 ft. lbs. Torque drawing the shaft and seals into proper alignment.

Fully seated O-Ring

leaning the Outer Tub forward, then roll the Drive Belt of Pulley.

10. Place the new seal onto the insertion tool. Wipe the outside diameter of the seal with a soap solution to help installation.

Linethesealupto the bearing housing and press rmlyinto

the housing until the seal is fully seated.

6. Remove the bolt (9/16” socket) in the center of the Drive Pulley. Slide Pulley off of Spinner Support Shaft. If necessary use Spanner Wrench to apply leverage to loosen Pulley.

Wrench

WRENCH

7. Separate the Spinner Support from the Spin Basket by removing

the3rearBafesinsidetheSpinTub.

8. Remove 3 lock nuts with a 1/2” socket.

STEEL

WASHER

LIP SEAL

INSERTION TOOL

“O”-Ring

O-RING

Apply Molykote Along Shaft

APPLY

MOLYKOTE

ALONG

SHAFT

FULLY

SEATED

Fully seated

O-RING

O-Ring

12. Reinstall the 3 plastic washers on Spinner. Assemble the Spinner and Spinner Support Shaft. Position the Spinner with Spinner Support shaft into the Outer Tub.

13. Install the Drive Pulley onto the Spinner Support Shaft. Replace the tabbed pulley washer with new 1-1/4” washer along with the new retaining bolt. Tighten retaining bolt to 33 ft. lbs. Torque drawing the shaft and seals into proper alignment.

1-11/16” WASHER

1-11/16” Washer

1-1/4” Washer

1-1/4” WASHER

Retaining Bolt

RETAINER BOLT

9. Remove Spin Basket by lifting off of threaded studs on Spinner Support.

A multi-lipped water seal is positioned on the Spinner Support

Shaft leading to the Outer Tub Bearings. This prevents water from inside the tub from reaching the bearings. The water seal is accessed only by removing the Spinner Support Shaft and is comprised of a stainless steel seal face which mates with a rubber gasket.

Remove the rubber seal gently from inside the Outer Tub.

Remove the plastic spacer, if so equipped. Once removed, clean the surface exposed under the seal. Discard the rubber seal and plastic spacer.

14. Run the Drive Belt over Motor Pulley and roll onto Drive Pulley.

15. Install Front Shroud Front Panel and Top Cover.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

16. Plug in washer or reconnect power.

17. Testwasher for properoperation.Cyclewasherthrough a ll

and drain cycle to check for leaks.

— 2 — W11086225 A

+ 2 hidden pages