Maytag MGDX5SPAW0 Installation Guide

GAS DRYER

iNSTALLATiON iNSTRUCTiONS

27" Wide Models

INSTRUCCIONES

DE INSTALACION DE LA SECADORA

Modelos

Table of Contents

DRYER SAFETY ................................................................ 2

iNSTALLATiON REQUIREMENTS .................................... 4

Tools and Parts .................................................................... 4

Location Requirements ...................................................... 5

Install Leveling Legs ........................................................... 6

GAS DRYER POWER HOOKUP ................................................. 6

Gas Supply Requirements .................................................. 6

Electrical Requirements ..................................................... 8

VENTING ...................................................................................... 8

Venting Requirements ......................................................... 8

Plan Vent System ................................................................. 9

Venting Kits ........................................................................ 10

install Vent System ............................................................ 11

Make Gas Connection ...................................................... 11

Connect Vent ..................................................................... 11

LEVEL DRYER ........................................................................... 12

COMPLETE iNSTALLATiON CHECKLIST ............................... 12

REVERSE DOOR SWING (OPTIONAL} .................................... 13

TROUBLESHOOTING ............................................................... 18

de 27"

SEGURIDAD DE LA SECADORA .................................. 19

REQUISITOS DE INSTALACION ................................... 21

CONEXION DE ENERGIA DE LA SECADORA A GAS ........... 24

VENTILACION .......................................................................... 26

NIVELACION DE LA SECADORA ............................................ 30

LISTA DE CONTROL DE LA INSTALACION TERMINADA .... 31

CAMBIO DEL SENTIDO DE ABERTURA DE LA PUERTA .... 31

SOLUCION DE PROBLEMAS .................................................. 36

a gas

Herramientas y piezas ..................................................... 21

Requisitos de ubicaci6n .................................................. 22

Instaiaci6n de las patas niveladoras .............................. 23

Requisitos del suministro de gas ................................... 24

Requisitos el_ctricos ....................................................... 25

Requisitos de ventiiaci6n ................................................ 26

Planificaci6n del sistema de ventilaci6n ........................ 27

Juegos de ventilaci6n ...................................................... 28

Instalaci6n del sistema de ventilaci6n ........................... 29

Cone×ibn del suministro de gas ..................................... 29

Conexi6n del ducto de escape ....................................... 30

iNSTALLATiON NOTES
Date of purchase:

Date of installation:
Installer:

Model number:
Serial number:

W10486878A

NOTAS SOBRE LA INSTALACION
Fecha de compra:

Fecha de instalaci6n:

Instalador:

N_mero de modelo:
N_mero de serie:

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be kifled or seriously injured if you don't immediately
follow instructions,

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

WARNING - ...i.kofFi, "

- Clothes dryer installation must be performed by a qualified installer.

- Install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with fle×ible plastic venting materials or flexible metal
(foil type) duct. if flexible metal duct is installed, it must be of a specific type identified

by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting
materials are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire,

- To reduce the risk of severe injury or death, follow all installation instructions.

- Save these instructions.

iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSi Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

® Do not try to light any appliance.
e Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building, or area of all occupants.
® Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• if you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.
If a gas leak is detected, follow the "What to do if you smell gas" instructions.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[] Read all instructions before using the dryer.
[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry=
cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or
explode.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the drying compartment.
[] Do not reach into the dryer if the drum is moving.
[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

SAVE THESE iNSTRUCTiONS

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this
Use and Care Guide or in published user=repair
instructions that you understand and have the skills to
carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric
softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber=like materials.

[] Clean lint screen before or after each load.
[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,
and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See "Electrical Requirements" located inthe installation

instructionsfor grounding instructions.

3

in the State of Massachusetts, the following installation instructions apply:

[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.
[] A flexible gas connector, when used, must not exceed 3 feet.

State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.

IMPORTANT SAFETY INSTRUCTIONS

When discarding or storing your old clothes dryer, remove the door.

SAVE THESE INSTRUCTIONS

iNSTALLATiON

Toomsand Parts

Gather the required tools and parts before starting installation.

Tools needed:

@

Flat-blade screwdriver

1/4" nut driver or socket
wrench (recommended)

#2 Phillips screwdriver

Tin snips (new vent

installations)

REQUIREMENTS

Adjustable wrench that
opens to 1" (25 mm) or

hex-head socket wrench

Utility knife Putty knife

Caulking gun and compound
(for installing new exhaust vent)

Tape measure

Level Pliers

4

Vent clamps

db

8" or 10" pipe wrench

Pipe-joint compound
resistant to LP gas

8" or 10" adjustable wrench
(for gas connections)

Parts supplied:

Leveling legs (4)

Parts package is located in dryer drum. Check that all parts
are included.

Parts needed:
Check local codes. Check existing electrical supply and venting.

See "Electrical Requirements" and "Venting Requirements"

before purchasing parts.

Mobile home installations require metal exhaust system
hardware, available for purchase from the dealer from whom
you purchased your dryer. For further information, please

reference the "Assistance or Service" section of the Use and
Care Guide.

Optional Equipment: (Not supplied with dryer)
Refer to your Use and Care Guide for information about

accessories available for your dryer.

The dryer must not be installed or stored in an area where it will

be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes, or

sleeping quarters. Contact your local building inspector.
NOTE: No other fuel-burning appliance can be installed in the

same closet as a dryer.

installation clearances:
The location must be large enough to allow the dryer door to

open fully.
Most installations require a minimum 51/2"(140 mm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting
Requirements."

Dryer Dimensions

43" (1092 mm)

11092 turn}

•29,?; .29v2,_,

(749 ram} \(749 mm) X "X_'_"_ 27,, _\ _ _\

133A,,

mm)

Explosion Hazard

Keep flammable materials and vapors, such as
gasoline, away from dryer.

Place dryer at least 18 inches (460 mm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need:
[] A location allowing for proper exhaust installation.

See "Venting Requirements."

[] A separate 15- or 20-amp circuit for gas dryers.
[] If you are using power supply cord, a grounded electrical

outlet located within 2 ft. (610 mm) of either side of dryer.
See "Electrical Requirements."

[] A sturdy floor to support dryer and a total weight (dryer

and load) of 200 Ibs. (90.7 kg). The combined weight of
a companion appliance should also be considered.

[] Level floor with maximum slope of 1" (25 mm) under entire

dryer. If slope is greater than 1" (25 mm), install Extended
Dryer Feet Kit, Part Number 279810. If not level, clothes

may not tumble properly and automatic sensor cycles
may not operate correctly.

Do not operate your dryer at temperatures below 45°F (7°C).
At lower temperatures, the dryer might not shut off at the end

of an automatic cycle. Drying times can be extended.

A B

A. Large opening side-swing door
B. Wide opening hamper door

installation Spacing

.._ 3I1.

.H_ 1_"i11BX,^ __

I_ II_mm_ ' 48in'_

(310crn)_

... _ _._ (155cml

1"-'_ _- 27"-_ _ 1" -_I"*F 29_/4"H5Y2"*_-

(25rnrn) (686mm) (25mm)_5mm}(74,1mm}(140rnrn)

A B

A. Recessed area

B. Side view - closet or confined area
C. Closet door with vents

24i_*,

(76mm)

-T

4f 3II,

(76ram}

*Required spacing

installation spacing for recessed area or closet
Thedimensions shown arefor the minimum spacing allowed.

[] Additional spacing should be considered for ease of

installation and servicing.

[] Additional clearances might be required for wall, door, and

floor moldings.

[] Additional spacing of 1" (25 mm) on all sides of the dryer is

recommended to reduce noise transfer.

[] For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are

acceptable.

[] Companion appliance spacing should also be considered.

5

Mobile home - Additional installation requirements

This dryer is suitable for mobile home installations. The

installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280).

[] Metal exhaust system hardware, available for purchase.

For further information, please reference the "Assistance
or Service" section of the Use and Care Guide.

[] Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such
as a nearby window) should be at least twice as large
as the dryer exhaust opening.

mnstaH Leve in 9 Legs

Excessive Weight Hazard

Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.

2, Screw in leveling legs

diamond

marking

Examine leveling legs and find diamond marking. Screw legs

into leg holes by hand. Use a wrench to finish turning legs

until diamond marking is no longer visible.
Now stand the dryer on its feet. Slide the dryer until it is

close to its final location. Leave enough room to connect
the exhaust vent.

For mobile home use
Gas dryers must be securely fastened to the floor.

To avoid damaging floor, use a large flat piece of cardboard
from dryer carton; place under entire back edge of dryer.

Firmly grasp dryer body (not console panel) and gently lay

dryer down on cardboard.

Mobile home installations require a Mobile Home Installation

Hold-down Kit. For ordering information please reference

the Use and Care Guide.

GAS DRYER POWER

HOOKUP

Gas SuppMy Requirements

Explosion Hazard

Use a new CSA International approved gas supply line,
Install a shut-off valve.

Securely tighten all gas connections.
If connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (330 ram) water
column.

Examples of a qualified person include:

licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.

Failure to do so can result in death, explosion, or fire,

Gas type

Natural gas:
This dryer is equipped for use with Natural Gas. It is design-

certified by CSA International for LP (propane or butane) gases
with appropriate conversion.

[]

Your dryer must have the correct burner for the type of gas
in your home. Burner information is located on the rating
plate in the door well of your dryer. If this information does
not agree with the type of gas available, please reference the

"Assistance or Service" section of the Use and Care Guide.

LP gas conversion:
Conversion must be made by a qualified technician.

No attempt shall be made to convert the dryer from the gas
specified on the model/serial rating plate for use with a different
gas without consulting the serving gas supplier.

iMPORTANT: The gas installation must conform with local codes,
or, in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1/NFPA 54.

Gas supply line

[] 1/2" NPT pipe is recommended.
[] 3/8" approved tubing is acceptable for lengths under

20 ft. (6.1 m) if local codes and gas supplier permit.

[] Must include 1/8" NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas
connection to the dryer (see illustration).

[] Must include a shut-off valve:

in the U.S.A.:

An individual manual shut-off valve must be installed

within six (6) feet (1.8 m) of the dryer in accordance with
the National Fuel Gas Code, ANSI Z223.1.

Option 1 (Recommended Method}
Flexible stainless steel gas connector:

[] If local codes permit, use a new flexible stainless steel gas

connector (Design Certified by the American Gas Association
or CSA International) to connect your dryer to the rigid gas
supply line. Use an elbow and a 3/8" flare x 3/8" NPT adapter
fitting between the stainless steel gas connector and the
dryer gas pipe, as needed to prevent kinking.

Option 2 (Alternate Method}
Approved aluminum or copper tubing:

[] Lengths over 20 ft. (6.1 m) can use 3/8" approved tubing

(if codes and gas supplier permit).
[] If you are using Natural Gas, do not use copper tubing.
[] 3/8" flare x 3/8" NPT adapter fitting between dryer pipe and

3/8" approved tubing.
[] Lengths over 20 ft. (6.1 m) should use larger tubing and a

different size adapter fitting.
[] If your dryer has been converted to use LP gas, 3/8" LP

compatible copper tubing can be used. If the total length

of the supply line is more than 20 ft. (6.1 m), use larger pipe.

NOTE: Pipe joint compounds that resist the action of LP

gas must be used. Do not use TEFLON ®t tape.

Dryer gas pipe

[] The gas pipe that comes out through the rear of your dryer

has a 3/8" male pipe thread.

*53/4" A

(159 rnrn)

The shut-off valve location should be easy to reach for opening
and closing.

E

A i

B

A. 3/8" flexible gas connector
B. 3/8" pipe to flare adapter fitting

C. 1/8" NPT minimum plugged tapping
D. 1/2" NPT gas supply line

E. Gas shut-off valve

Gas supply connection requirements

There are many methods by which your gas dryer can be
connected to the gas supply. Listed here are some guidelines

for two different methods of connection.
This dryer must be connected to the gas supply line with a

listed flexible gas connector that complies with the standard for

connectors for gas appliances, ANSI Z21.24 or CSA 6.10.

1 1/2"

(38 turn)

A. 3/8" NPT dryer pipe

Burner input requirements

Elevations up to 10,000 ft. (3,048 m}:

[] The design of this dryer is certified by CSA international for

use at altitudes up to 10,000 ft. (3,048 m), above sea level at

the B.T.U. rating indicated on the model/serial number plate.

Burner input adjustments are not required when the dryer is

operated up to this elevation.
Elevations above 10,000 ft. (3,048 m):

[] When installed above 10,000 ft. (3,048 m) a 4% reduction

of the burner B.T.U. rating shown on the model/serial

number plate is required for each 1,000 ft. (305 m)

increase in elevation.
Gas supply pressure testing

[] The dryer must be disconnected from the gas supply piping

system during pressure testing at pressures greater than

1/2 psi.

?®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

7

EMectrica Requirements

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

[]

120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical
supply is required. A time-delay fuse or circuit breaker is
recommended. It is also recommended that a separate circuit
serving only this dryer be provided.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes
and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative
or personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug provided with

the dryer: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

VENTING

Venting Requirements

Fire Hazard

Use a heavy metal vent,
Do not use a plastic vent.

Do not use a metal foil vent,
Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling, attic, crawlspace, or a concealed space
of a building. Only rigid or flexible metal vent shall be used for
exhausting.

1

_ 4"

4" (102 mm) heavy metal exhaust vent

[] Only a 4" (102 mm) heavy metal exhaust vent and clamps

may be used.
[] Do not use plastic or metal foil vent.

Rigid metal vent:
[] Recommended for best drying performance and to avoid

crushing and kinking.
Flexible metal vent: (Acceptable only ifaccessible to clean)

[] Must be fully extended and supported in final dryer location.
[] Remove excess to avoid sagging and kinking that may result

in reduced airflow and poor performance.
[] Do not install in enclosed walls, ceilings, or floors.
[] The total length should not exceed 73/4ft. (2.4 m).
NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not plugged
with lint. Replace plastic or metal foil vents with rigid metal
or flexible metal vents. Review "Vent System Chart" and, if
necessary, modify existing vent system to achieve best drying

performance.

(102 ram)

Exhausthoods:

[] Must be at least 12" (305 ram) from ground or any object

that may obstruct exhaust (such as flowers, rocks, bushes,

or snow).

Recommended St_vies:

P(an Vent System

Recommended exhaust installations

_HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH_

Typical installations vent the dryer from the rear of the dryer.

Other installations are possible.

B

Louveredhood

Box hood

Acceptable Style:

Angled hood

Elbows:
[] 45° elbows provide better airflow than 90° elbows.

............. Bet

A. Dryer
B. Elbow

C, Wall
D. Exhaust hood

E. Clamps

F. Rigid metal or flexible metal vent
G. Vent length necessary to connect elbows

H.Exhaust outlet

L Optional side exhaust outlet

Optional exhaust installations:

27" Wide Models can be converted to exhaust out the right side,

left side, or through the bottom (4-way vent kit). Each kit includes

step-by-step instructions. For ordering information, see "Venting

Kits."

?

Clamps:
[] Use clamps to seal all joints.

[] Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct
and catch lint. Do not use duct tape.

Improper venting can cause moisture and lint to collect
indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

See "Venting Kits" for more information.

Fire Hazard

Cover unused exhaust holes with a manufacturer's
exhaust cover kit.

Contact your local dealer.
Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

B C

A. Standard rear offset exhaust installation
B. Left- or right-side exhaust instaflation

C. Bottom exhaust instaflation

9

A(ternate installations for close clearances
Venting systems come in many varieties. Select the type best

for your installation. Two close-clearance installations are shown.

Refer to the manufacturer's instructions.

Over-The-Top installation (also available with one offset elbow)

Periscope installation

NOTE: The following kits for close clearance alternate

installations are available for purchase.

Venting Kits

For more information, call 1-800-901-2042, or visit us
at www.applianceaccessories.com.

Part Number Description

8171587RP 0-5" Metal vent periscope
4396037RP 0"-18" Metal vent periscope
4396011 RP 18"-29" Metal vent periscope

4396014 29"-50" Metal vent periscope
4392892 In-Wall metal DuraVent TM Periscope

W10470674 4-way vent kit - universal grey
4396028 Sure Connect TM venting kit

(over-the-top installation)

4396009RP 5' Universal connect vent, flexible dryer venting
4396010RP 6' SecureConnect TM vent, flexible dryer venting

4396013RB Dryer vent installer's kit
4396033RP 5' flexible dryer venting with clamps

4396727RP 8' flexible dryer venting with clamps
4396004 Dryer offset elbow

4396005 Wall offset elbow
4396006RW DuraSafe TM close elbow

4396007RW Through-the-wall vent cap
4396008RP 4" steel dryer venting clamps - 2 pack

8212662 Flush mounting Iouvered vent hood 4"

10

Special provisions for mobile home installations:
The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

Determine vent path:

[] Select route that will provide straightest and most direct path

outdoors.

[] Plan installation to use fewest number of elbows and turns.
[] When using elbows or making turns, allow as much room

as possible.

[] Bend vent gradually to avoid kinking.
[] Use as few 90° turns as possible.

Determine vent length and elbows needed for best
drying performance:

[] Use following "Vent System Chart" to determine type of vent

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified
in "Vent System Chart." Exhaust systems longer than those
specified will:

[] Shorten life of dryer.
[] Reduce performance, resulting in longer drying times and

increased energy usage.

The "Vent System Chart" provides venting requirements that
will help achieve best drying performance.

Vent System Chart

Number of Type Box/Iouvered Angled
90 ° turns or of vent hoods hoods

elbows

0 Rigid metal 64 ft. (20 m) 58 ft. (17.7 m)

1 Rigid metal 54 ft. (16.5 m) 48 ft. (14.6 m)

2 Rigid metal 44 ft. (13.4 m) 38 ft. (11.6 m)

3 Rigid metal 35 ft. (10.7 m) 29 ft. (8.8 m)

4 Rigid metal 27 ft. (8.2 m) 21 ft. (6.4 m)

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add
one 90° turn to the chart.

:2. Plan pipe fitting connection

A

12" rain.

(305 ram)

Install exhaust hood and use caulking compound to seal
exterior wall opening around exhaust hood.

Vent must fit over the exhaust hood. Secure vent to exhaust

hood with 4" (102 mm) clamp. Run vent to dryer location
using straightest path possible. Avoid 90 ° turns. Use clamps
to seal all joints. Do not use duct tape, screws, or other
fastening devices that extend into interior of vent to secure
vent, because they can catch lint.

A. 3/8" flexible gas connector C. 3/8" to 3/8" pipe elbow

B

B. 3/8" dryerpipe D. 3/8" pipe-to-flare adapter fitting

A combination of pipe fittings must be used to connect dryer

to existing gas line. A recommended connection is shown.

Your connection may be different, according to supply line

type, size, and location.

f

C

3. Open shut=off valve

c,o

pen valve

Open shut-off valve in supply line; valve is open when handle

is parallel to gas pipe. Then, test all connections by brushing

on an approved noncorrosive leak-detection solution.

Bubbles will show a leak. Correct any leaks found.

Make Gas Connection

1, Connect gas supply to dryer

Flared Non-flared

male fitting male fitting

Remove red cap from gas pipe. Using a wrench to tighten,
connect gas supply to dryer. Use pipe-joint compound
on threads of all non-flared male fittings. If flexible metal

tubing is used, be sure there are no kinks.
NOTE: For LP gas connections, you must use pipe-joint

compound resistant to action of LP gas. Do not use

TEFLON ®ttape.

1®TEFLON is aregistered trademark of E.I. Dupont De Nemours and Company. 1 1

Using a4" (102 mm) clamp, connect vent to exhaust outlet

in dryer. If connecting to existing vent, make sure vent is

clean. Dryer vent must fit over dryer exhaust outlet and inside

exhaust hood. Check that vent is secured to exhaust hood

with a 4" (102 mm) clamp.