Maytag MGDB766FW User Manual

Gas and Electric Dryer

PRODUCT MODEL NUMBERS

MEDB766F, MGDB766F

Installation clearances:

For each arrangement, consider allowing more space for ease of
installation and servicing, spacing for companion appliances, and
clearances for walls, doors, and oor moldings. Space must be
large enough to allow door to fully open. Add spacing on all sides
of dryer to reduce noise transfer. If a closet door or louvered door
is installed, top and bottom air openings in door are required.

Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes, or
sleeping quarters. Contact your local building inspector.

Dryer Dimensions

Front View

29"

(737 mm)

407/8"

(1038 mm)

1

/2"

(13 mm)

NOTE: Minimum height of leveling legs should be 1/2" (13 mm),
or to match the height of the accompanying washer.

Side View

503/4"

(1289 mm)

281/4"

(717 mm)

42"

(1067 mm)

281/4"

(717 mm)

Back View

43/4"

(121 mm)

141/2"

(368 mm)

4"

(101 mm)

91/4"

(235 mm)

(768 mm)

1

/4"

1

(32 mm)

301/4"

(121 mm)

43/4"

141/2"

(368 mm)

91/4"

(235 mm)

1

(32 mm)

Steam Non-Steam

Installation spacing for recessed area
or closet

The dimensions shown are for the minimum spacing allowed.

■ Additional spacing should be considered for ease of

installation and servicing.

■ Additional clearances might be required for wall, door,

and oor moldings.

■ Additional spacing of 1" (25 mm) on all sides of the dryer

is recommended to reduce noise transfer.

■ For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.

■ Companion appliance spacing should also be considered.

Installation Spacing

14" max

(356 mm)

3"/3"

18"/18"

(457 mm/

457 mm)

(76 mm/

76mm)

2

/48"

48"
(310 cm
310 cm2)

1

/4"

2

2/

A B

A. Wide opening side-swing door
B. Wide opening hamper door

6"/0"

(152 mm/

0 mm)

1"/0"

(25 mm/0 mm)

(25 mm/25 mm)

Recommended/Minimum spacing

1"/1"

3"/3"

(76 mm/

76mm)

2/

2

24"

24"

2/

(155 cm

155 cm2)

W10848818A

08/2016

INSTALLATION REQUIREMENTS

GAS SUPPLY REQUIREMENTS

Gas supply: This dryer is equipped for use with Natural gas. Dryer can be converted to L.P. gas. When rigid pipe is used it should be 1/2" IPS. When
acceptable to the gas supplier and local codes, 3/8" approved aluminum or copper tubing may be used for lengths under 20 ft (6.1 m) if local codes
and gas supplier permit. Lengths over 20 ft (6.1 m) should use larger tubing and a different size adapter tting. Pipe-joint compounds resistant to the
action of L.P. gas must be used. An individual manual shutoff valve must be installed within 6 ft (1.8 m) of the dryer in accordance with the National
Fuel Gas Code ANSI Z223.1.

ELECTRICAL REQUIREMENTS - Gas models only

A 3 or 4 wire, single phase, 120/240 volt, 60 Hz, AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specied on the serial/
rating plate) on a separate 30-amp circuit, fused on both sides of the line. Connect to an individual branch circuit. Do not have a fuse in the neutral or
grounding circuit. Do not use an extension cord.

ELECTRICAL REQUIREMENTS - Electric models only

A 3 or 4 wire, single phase, 120/240 volt, 60 Hz, AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specied on the serial/
rating plate) on a separate 30-amp circuit, fused on both sides of the line. Connect to an individual branch circuit. Do not have a fuse in the neutral or
grounding circuit. Do not use an extension cord.

WATER (STEAM MODELS ONLY) REQUIREMENTS

The dryer must be connected to the cold water faucet using new inlet hoses. Do not use old hoses. Do not overtighten. Damage to the coupling can
result. Cold water faucet located within 4 ft. (1.2 m) of the water ll valves, and water pressure of 20-100 psi (137.9-689.6 kPa). You may use the water
supply for your washer using the “Y” connector and short hose which are provided.

VENTING REQUIREMENTS

WARNING: To reduce the risk of re, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent, chimney, wall,
ceiling, attic, crawlspace, or a concealed space of a building. Only rigid or

exible metal vent shall be used for exhausting.

4"

(102 mm)

4" (102 mm) heavy metal exhaust vent

■ Only a 4" (102 mm) heavy metal exhaust vent and clamps
may be used.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid crushing
and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■ Must be fully extended and supported in nal dryer location.

■ Remove excess to avoid sagging and kinking that may result in
reduced airow and poor performance.

■ Do not install in enclosed walls, ceilings, or oors.

■ The total length should not exceed 73/4 ft. (2.4 m).

NOTE: If using an existing vent system, clean lint from entire length of
the system and make sure exhaust hood is not plugged with lint. Replace
plastic or metal foil vents with rigid metal or exible metal vents. Review
“Vent System Chart” and, if necessary, modify existing vent system to

achieve best drying performance.

Exhaust hoods:

■ Must be at least 12" (305 mm) from ground or any object

that may obstruct exhaust (such as owers, rocks, bushes,
or snow).

Recommended Styles:

Acceptable Style:

Angled hood

Determine vent path:

■ Select route that will provide straightest and most direct path
outdoors.

■ Plan installation to use fewest number of elbows and turns.

■ When using elbows or making turns, allow as much room
as possible.

■ Bend vent gradually to avoid kinking.

■ Use as few 90° turns as possible.

Determine vent length and elbows needed
for best drying performance:

■ Use following “Vent System Chart” to determine type of vent material
and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specied
in “Vent System Chart.” Exhaust systems longer than those specied
will:

■ Shorten life of dryer.

■ Reduce performance, resulting in longer drying times and
increased energy usage.

The “Vent System Chart” provides venting requirements that will help
achieve best drying performance.

Vent System Chart

Number of

90° turns

or elbows

0 Rigid metal 64 ft. (20 m) 58 ft. (17.7 m)

1 Rigid metal 54 ft. (16.5 m) 48 ft. (14.6 m)

2 Rigid metal 44 ft. (13.4 m) 38 ft. (11.6 m)

3 Rigid metal 35 ft. (10.7 m) 29 ft. (8.8 m)

4 Rigid metal 27 ft. (8.2 m) 21 ft. (6.4 m)

Type

of vent

Box/louvered

hoods

Angled

hoods

Louvered hood Box hood

Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation
our products, we reserve the right to change materials and specications without notice. Instructions packed with product. Specications subject to change without notice.