Maytag MGD7230HW, MED7230HC, MGD7230HC User Manual

Dimension Guide

Maytag® Dryer with Extra Power and

Advanced Moisture Sensing - 7.4 cu. ft.

White Available
MED7230HW - Electric
MGD7230HW - Gas

43 1∕8"
Height

Metallic Slate Available
MED7230HC - Electric
MGD7230HC - Gas

W11412670A

29 7∕8"
Depth

27"
Width

DETAILED PLANNING DIMENSIONS

WARNING: To reduce the risk of re, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS and

INSTALLATION INSTRUCTIONS, located in your appliance's Owner's Manual, before installing and operating this appliance.

Electrical Requirements

Fuel Type Electric Gas

Minimum Circuit
Amperage Rating

Maximum AMP Draw 26 A 6 A
Operating Voltage 240 V - AC only 120 V - AC only
Operating Frequency 60 Hz

30 A 15 A

D

A

C

B

F

Product Dimensions

in (min) mm (min) in (max) mm (max)

A Height (with feet) 43 1∕

8

1095.5 44 1∕
B Width 27 685.8 - ­C Top Height (with feet) 39 5∕
D Depth 29 7∕
E Side Vent Height (feet min) 6 1∕
F Side Vent (from back) 10 3∕

8

8

4

8

1005.7 40 5∕

759.1 - -

158.45 7 1∕

263.68 - -

8

8

4

1120.9

1031.1

183.85

E

2

DETAILED PLANNING DIMENSIONS

H

G

I

J

K

L

M

Q

P

N

O

Product Dimensions

in (min) mm (min) in (max) mm (max)

G

Depth with Door Open 45 13∕
H Strain Relief from Side (elec) 6 7∕

I Strain Relief Height (elec) 29 1∕

J Power Cord from Side (gas) 3 3∕
K Power Cord Height (gas) 30 15∕

Power Cord Length (gas) 59 7∕
L Gas Valve Height 8 5∕
M Gas Valve from Side 1 7∕
N Exhaust Duct Height 6 ¼ 158.38 7 ¼ 183.78
O Exhaust Duct from Side 14 1∕
P Water Inlet Height (steam models) 9 15∕
Q Water Inlet from Side (steam models) 8 9∕

16

16

8

16

16

8

8

16

16

16

16

1163.5 - -

162.9 - -

739.77 30 1∕

8

765.17

96.25 - -

785.18 31 15∕

16

810.58

1521.09 - -

218.63 9 5∕

8

244.03

36.40 - -

356.7 - -

251.78 10 15∕

16

277.18

217.9 - -

3

DETAILED PLANNING DIMENSIONS

Spacing for recessed area or closet installation

The dimensions shown are for the recommended spacing allowed.

Ƀ Additional spacing should be considered for ease of installation and servicing.
Ƀ Additional clearances might be required for wall, door, and oor moldings.
Ƀ Additional spacing of 1" (25 mm) on all sides of the dryer is recommended to reduce noise transfer.
Ƀ For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors

with equivalent ventilations openings are acceptable.

Ƀ Companion appliance spacing should also be considered.

14" max

(356 mm)

3"

18"

(460 mm)

(76 mm)

(310 cm)

48 in.

2

6"/0"*

(152 mm/0 mm)

1"/0"*

(25 mm/0 mm)

*Recommended/Minimum spacing

1"

(25 mm)

3"

(76 mm)

2

2/

24 in.

24"

24"

(155 cm)

2

4