Maytag MFF2258FEZ Owner's Manual

REFRIGERATOR USER INSTRUCTIONS INSTRUCTIONS D’UTILISATION DU RÉFRIGÉRATEUR

THANK YOU for purchasing this high-quality product. Register your new refrigerator at www.maytag.com. In Canada, register your refrigerator at www.maytag.ca.

For future reference, please make a note of your product model and serial numbers. These can be located on the inside wall of the refrigerator compartment.

Model Number___________________________________________ Serial Number_____________________________________________

Nous vous REMERCIONS d’avoir acheté ce produit de grande qualité. Enregistrez votre nouveau réfrigérateur au www.maytag.com. Au Canada, enregistrez votre réfrigérateur au www.maytag.ca.

Pour référence future, veuillez prendre en note les numéros de modèle et de série de votre produit. Ceux-ci se trouvent sur la paroi interne du compartiment de réfrigération.

Numéro de modèle_______________________________________ Numéro de série____________________________________________

TABLE OF CONTENTS / TABLE DES MATIÈRES

REFRIGERATOR SAFETY .......................... 2

Proper Disposal of Your Old Refrigerator ... 3

INSTALLATION INSTRUCTIONS ...............3

Unpack the Refrigerator ...........................3

Location Requirements ............................ 4

Electrical Requirements ...........................4

Water Supply Requirements ....................4

Connect the Water Supply ....................... 5

Refrigerator Door(s) and Drawer .............. 6

Door Closing and Door Alignment ......... 12

REFRIGERATOR USE .............................. 12

Opening and Closing Doors

(French door models) ............................. 12

Using the Controls .................................13

Electronic Controls ................................. 13

Digital Controls ....................................... 13

Crisper Humidity Control .......................15

Ice Maker ................................................15

Water Dispenser ..................................... 15

Water Filtration System .......................... 16

REFRIGERATOR CARE ........................... 16

Cleaning .................................................16

Changing the LED Module ..................... 17

Vacation and Moving Care .....................17

TROUBLESHOOTING .............................. 18

Refrigerator Operation ...........................18

Temperature and Moisture ..................... 19

Ice and Water .........................................19

Accessories ............................................ 20

PERFORMANCE DATA SHEETS ............. 21

SÉCURITÉ DU RÉFRIGÉRATEUR........... 23

Mise au rebut du vieux réfrigérateur ...... 24

INSTRUCTIONS D’INSTALLATION ......... 24

Déballage du réfrigérateur......................24

Exigences d’emplacement .....................25

Spécicationsélectriques ...................... 25

Spécications de l’alimentation en eau ... 26

Raccordement à la canalisation d’eau ....26

Porte et tiroir du réfrigérateur ................. 28

Fermeture et alignement de la porte ......34

UTILISATION DU RÉFRIGÉRATEUR ......34

Ouverture et fermeture des portes

(modèles avec porte à double battant) .... 34

Utilisation des commandes ...................35

Commandes électroniques .................... 35

Commandes numériques .......................35

Réglage de l’humidité dans le tiroir

à légumes ............................................... 37

Machine à glaçons ................................. 37

Distributeur d’eau ................................... 37

Système de ltration de l’eau ................38

ENTRETIEN DU RÉFRIGÉRATEUR ........ 38

Nettoyage ............................................... 38

Remplacer le module à DEL ..................39

Précautions à prendre avant

les vacances ou le déménagement ....... 39

DÉPANNAGE .............................................40

Fonctionnement du réfrigérateur ...........40

Température et humidité ........................41

Glaçons et eau ....................................... 41

Accessoires ............................................ 42

FEUILLES DE DONNÉES

SUR LA PERFORMANCE ........................ 43

W11368748B

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTA NT SAFETY INSTRUCTIONS

WARNING:

■ Plug into a grounded (earthed) outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Use nonflammable cleaner.

■ Do not store or use petrol, flammable liquids or gas in the

vicinity of this or other electrical appliances. The fumes can

cause fires or explosions.

■ Do not store explosive substances such as aerosol cans

with a flammable propellant in this refrigerator.

■ Do not use or place electrical devices inside the refrigerator

compartments if they are not of the type expressly

authorized by the manufacture.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ Keep ventilation openings, in the appliance enclosure or in

the built-in structure, clear of obstruction.

■ Do not use mechanical devices or other means to accelerate

the defrosting process, other than those recommended by the manufacturer.

■ Do not damage the refrigerant circuit.

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

■ Do not use electrical appliances inside the food storage

compartments of the appliance, unless they are of the type recommended by the manufacturer.

■ A qualified service technician must install the water line and

ice maker. See installation instruction supplied with

ice maker kit IC15B for complete details.

■ Connect to a potable water supply only.

■ Use a sturdy glass when dispensing ice (on some models).

■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

■ Children should be supervised to ensure that they do not

play with the appliance.

■ To avoid the risk of children becoming trapped and

suffocating, do not allow them to play or hide inside the

refrigerator.

■ If the power supply cord is damaged, it must be replaced by

the manufacturer or its service agent or a similarly qualified

person.

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

DANGER: Risk of child entrapment. Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

■ Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your ngers. Wipe with warm water and dry.

■ Do not use sharp instruments, rubbing alcohol, ammable

uids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see “Refrigerator Safety.”

■ Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the oor with cardboard or hardboard to avoid oor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as oor damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in “Refrigerator Care.”

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Location Requirements

Electronic Temperature Control

Freezer

7 is the coldest

7 is the coldestrecommended setting 4

Humidity Control

On O

Press if moisture appears

Refrigerator

Scroll Down for Cooling O

WARNING

Electrical Requirements

Before you move your refrigerator into its nal location, it is important to make sure you have the proper electrical connection.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualied person. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.

Explosion Hazard

Keep ammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or re.

IMPORTANT: This refrigerator is designed for indoor, household use only.

This appliance is intended to be used in household and similar applications such as:

■ Staff kitchen areas in shops, ofce and other working

environments;

■ Farm houses and by clients in hotels, motels and other

residential type environments;

■ Bed and breakfast type environments;

■ Catering and similar non-retail applications.

To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) of space on each side and at the top. Allow for 1" (2.54 cm) of space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a xed wall, leave 2¹⁄2" (6.3 cm) minimum on the hinge side (some models require more) to allow for the door to swing open.

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Recommended Grounding Method

A 115 V, 60 Hz, AC only 15 A or 20 A fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator and approved accessories be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn Cooling OFF, and then disconnect the refrigerator from the electrical source. When you have nished, reconnect the refrigerator to the electrical source and turn Cooling ON. See “Using the Control(s).”

Water Supply Requirements

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

1/2" (1.25 cm)

2½" (6.3 cm)

TOOLS NEEDED:

■ 7/16" and 1/2" Open-end or

two adjustable wrenches

■ 1/4" Drill bit

■ Cordless drill

IMPORTANT:

■ Connect to potable water supply only.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

■ All installations must meet local plumbing code requirements.

F G

D E

■ Do not use a piercing-type or 3/16" (4.76 mm) saddle valve

which reduces water ow and clogs more easily.

■ Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain above freezing.

■ For models with water lters, the disposable water lter

should be replaced at least every 6 months.

Water Pressure

A cold water supply with water pressure of between 35 psi +and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualied plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of

a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).

If a reverse osmosis water ltration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 psi to 60 psi (276 kPa to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 psi to 60 psi (276 kPa to 414 kPa):

■ Check to see whether the sediment lter in the reverse

osmosis system is blocked. Replace the lter if necessary.

■ Allow the storage tank on the reverse osmosis system to rell

after heavy usage.

■ If your refrigerator has a water lter, it may further reduce

the water pressure when used in conjunction with a reverse osmosis system. Remove the water lter. See “Water Filtration System.”

If you have questions about your water pressure, call a licensed, qualied plumber

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■ Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and ordinances.

■ The water tubing on the back of the refrigerator (which is used

to connect to the household water line) is a PEX(cross-linked polyethylene) tube. Copper and PEX tubing connections from the household water line to the refrigerator are acceptable, and will help avoid off-taste or odor in your ice or water. Check for leaks.

We recommend contacting service to obtain current part numbers.

■ Install tubing only in areas where temperatures will remain

above freezing.

■ If you turn on the refrigerator before the water line is

connected, turn off the ice maker to avoid excessive noise or damage to the water valve.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Find a 1/2" to 1¹⁄4" (12.7 mm to 31.8 mm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the rear of the refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a 1/4" hole in the cold water pipe

you have selected.

A. Cold water pipe B. Pipe clamp C. Copper tubing D. Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4" drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten or you may crush the copper tubing.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe.

E. Compression sleeve F. Shutoff valve G. Packing nut

Connect to Refrigerator

Depending on your model, the water line may come down from the top or up from the bottom. Follow the connection instructions for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the

copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Conrm copper tubing is secure by pulling on copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to refrigerator cabinet with a “P” clamp.

5. Using an adjustable wrench, hold the nut on the plastic water

line to keep it from moving. Then, with a second wrench turn the compression nut on the copper tubing counterclockwise to completely tighten. Do not overtighten.

A B

A. “P” clamp B. Plastic water line

6. Check connection by pulling on copper tubing. Attach the

plastic water line to the refrigerator cabinet with a “P” clamp.

7. Turn on water supply to the refrigerator and check for leaks.

Correct any leaks.

C. Compression nut D. Copper tubing

Complete the Installation

WARNING

A. Copper tubing B. “P” clamp

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

C. Compression nut D. Compression sleeve

Style 2

1. Create a service loop (minimum diameter of 2 ft [61 cm])

with the copper tubing. Avoid kinks when coiling the copper tubing.

2. Remove the plastic cap from water valve inlet port. Place a

compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet

port. Shape tubing slightly so that the tubing feeds straight into the port to avoid kinks.

4. Slide the compression nut over the sleeve and screw into the

water valve inlet port.

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1. Plug into a grounded 3 prong outlet. NOTE: Allow 24 hours to produce the rst batch of ice.

Discard the rst three batches of ice produced. Allow 3 days to completely ll the ice contain.

Electrical Shock Hazard

Refrigerator Door(s) and Drawer

TOOLS NEEDED: 5/16", 3/8", 1/4" hex head socket wrenches,

B C

A. Plastic water tubing B. Sleeve

C. Compression nut D. Copper tubing

a #2 Phillips screwdriver, and a at-blade screwdriver.

IMPORTANT:

■ Your refrigerator has a standard reversible refrigerator door

with either a freezer door or freezer drawer, or French doors. Follow the instructions specic to the door style of your model.

■ All graphics referenced in the following instructions are

included later in this section after “Final Steps.” The graphics shown for the standard door are for a right-hand swing refrigerator (hinges factory installed on the right).

■ If you only want to remove and replace the doors see

“Remove Doors and Hinges” and “Replace Doors and Hinges.”

■ Before you begin, turn the refrigerator control OFF, and

remove food and adjustable door or utility bins from the doors.

Remove and Replace Handles

French Doors

Refrigerator Door(s)

■ To remove handles, use a 3/32" hex key to loosen the two

setscrews located on the side of each handle. Pull the handle straight out from the door or drawer. Make sure you keep the screws for reattaching the handles. See Handle graphics 1 or

■ To replace handles, reverse the directions.

Freezer Drawer

■ To remove handles, use a 3/32" hex key to loosen the two

setscrews located under each handle. Pull the handle straight out from the door or drawer. Make sure you keep the screws for reattaching the handles. See Graphic 4.

■ To replace handles, reverse the directions.

Freezer Door

■ To remove handle, use a at-blade screwdriver to remove

the two screws fastening the handle to the freezer door. See Graphic 4.

■ To replace handle, reverse the directions.

Remove Doors and Hinges

Standard Door

Freezer drawer models

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator door closed until you are ready to lift it

free from the cabinet. NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the refrigerator door free from the cabinet.

4. Remove the parts for the bottom hinge as shown in Bottom

Hinge graphic.

Freezer door models

1. Unplug refrigerator or disconnect power.

2. Keep the freezer door closed until you are ready to lift it free

from the cabinet. NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the refrigerator door free from the cabinet.

4. Remove the center hinge pin and remove the hinge screws as

shown in the Center Hinge graphic. Lift the freezer door free from the cabinet.

5. Remove the base grille by grasping the grille rmly with both

hands and pulling it toward you.

6. Remove the parts for the bottom hinge as shown in Bottom

Hinge graphic.

WARNING

Electrical Shock Hazard Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet. NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

3. Starting with the right-hand side door, remove the parts

for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door from the bottom hinge pin.

4. Remove the hinge pin cover from the bottom hinge pin and

keep it for later use. See Bottom Hinge graphic.

5. Before removing the left-hand side door, disconnect the wiring

plug located on top of the top hinge by wedging a at-blade screwdriver or your ngernail between the two sections. See Wiring Plug graphic.

NOTE: The green, ground wire remains attached to the hinge.

6. Remove the parts for the left-hand side door top hinge as

shown in the Top Hinge graphic. Lift the door from the bottom hinge pin.

NOTE: Remove the hinge pin cover from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

Reverse Door - Standard Door (optional)

IMPORTANT: If you want to reverse your door so it opens from the opposite side, follow these steps. If you are not reversing the door, see “Replace Door(s) and Hinges.”

Door Stop Screw

Flat-Head Handle Screw

Cabinet

1. Remove hinge screws from handle side and move them to

opposite side. See Graphic 1.

Refrigerator door

1. Remove the refrigerator handle assembly as shown in

Graphic 2. Keep all parts together.

2. Remove door handle seal screw front. Move to opposite side

of refrigerator door as shown in Graphic 5.

3. Remove the door stop. Move it to the opposite side of the

refrigerator door as shown in Graphic 3.

4. Attach refrigerator handle on opposite side of the refrigerator

door with the two screws as shown in Graphic 2. Replace handle trim as shown.

5. Tighten all screws. Set aside the door until hinges and freezer

compartment drawer are in place.

Door Handle Seal Screw Front

Cabinet Hinge Hole Plug

Freezer door

1. Remove the freezer handle assembly as shown in Graphic 4.

Keep all parts together.

2. Remove door stop. Move to opposite side of freezer door as

shown in Graphic 3.

3. Attach handle to opposite side of freezer door.

4. Tighten all screws. Set the door aside.

5. Remove the base grille by grasping the grille rmly with both

hands and pulling it toward you. NOTE: Place a shim under the bottom front edge of the

refrigerator cabinet to take the weight off the roller brackets.

6. Remove the screws from both roller brackets. See Graphic 6.

7. Remove the hinge plate located behind the roller bracket

and move it to the opposite side of the refrigerator. Move the hinge pin and shim to the outside hole on the hinge plate. See Graphic 6.

Replace Doors and Hinges

Standard Door

NOTE: Graphics may be reversed if door swing is reversed.

Freezer drawer models

1. Replace the parts for the bottom hinge as shown. Tighten

screws. NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

2. Assemble the parts for the top hinge as shown in Top Hinge

graphic. Do not tighten screws completely.

3. Adjust the door so that the bottom of the refrigerator door is

aligned with the top of the freezer drawer. Tighten all screws.

Freezer door models

1. Make sure the hinge plate is securely fastened behind the

roller bracket and that the hinge pin is inserted into the outside hole. Fully tighten all roller bracket screws. See Graphic 6.

2. Remove the shim that you placed under the front edge of the

refrigerator cabinet. Replace the freezer door. NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

3. Assemble the parts for the center hinge as shown in the

Center Hinge graphic, and tighten all the screws. Replace the refrigerator door.

4. Assemble the parts for the top hinge as shown in the Top

Hinge graphic. Do not tighten the screws completely.

5. Adjust the doors so that the bottom of the refrigerator door is

aligned with the top of the freezer door. Tighten all screws.

French Doors

1. Assemble the parts for the top hinges as shown in Top Hinge

graphic. Do not tighten the screws completely.

2. Replace the parts for the bottom hinges as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator doors. NOTE: Provide additional support for the refrigerator doors

while the hinges are being moved. Do not depend on the door gasket magnets to hold the doors in place while you are working.

3. Align each door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all screws.

4. Reconnect the wiring plug on top of the left-hand side

refrigerator door.

5. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT:

■ Two people may be required to remove and replace the

freezer drawer.

■ All graphics are included later in this section after “Final

Steps.”

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the

drawer front. See Drawer Front Removal graphic. NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front

Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to insert the two screws

in the bottom of the drawer front into the brackets. See Drawer Front Replacement graphic.

3. Completely tighten the four screws.

Final Steps

1. Check all holes to make sure that hole plugs and screws are

in place. Reinstall top hinge cover as shown in Top Hinge graphic.

2. Replace the base grille.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

3. Plug into a grounded 3 prong outlet.

4. Return all removable door parts to door and food to

refrigerator.

Standard Door - Freezer Door

Door Removal & Replacement

Top Hinge

B C

A. Hinge Cover Screw B. Top Hinge Cover C. 5/16" Hex-Head Hinge Screws D. Top Hinge

Center Hinge

Door Swing Reversal (optional)

A. 5/16" Hex-Head Hinge Screws

A. Flat-Head Handle Screws B. Refrigerator Door Handle

Front View Side View

A. Hinge Pin Cover C. Hinge Screws B. Center Hinge

Bottom Hinge

A. Hinge Pin Shim B. Bottom Hinge C. Hinge Plate D. Roller Bracket E. 3/8" Hex-Head Hinge Screws

A. Door Stop Screws B. Door Stop

A. Flat-Head Handle

Screws

Door Handle Seal Screw Front

A. Hinge Pin Shim B. Bottom Hinge C. Hinge Plate D. Roller Bracket E. 3/8" Hex-Head Hinge Screws

Standard Door - Freezer Drawer

Door Removal & Replacement

Top Hinge

A. Hinge Cover Screw B. Top Hinge Cover C. 5/16" Hex-Head Hinge Screws D. Top Hinge

Bottom Hinge

Door Swing Reversal (optional)

B C

A. Flat-Head Handle Screws B. Refrigerator Door Handle

Front View Side View

A. 5/16" Hex-Head Hinge Screws

A. Hinge Pin Cover C. Hinge Screws B. Center Hinge

Drawer Front Removal Drawer Front Replacement

A. Door Stop Screws B. Door Stop

A. Flat-Head Handle Screws B. Freezer Drawer Handle

Door Handle Seal Screw Front

A. Loosen 4 Door Bracket Screws

French Doors

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Door Removal and Replacement

Top Hinge

A. Hinge Cover Screw B. Top Hinge Cover C. 5/16" Hex-Head Hinge Screws D. Top Hinge

Bottom Hinge

A. Hinge Pin Cover C. Hinge Screws B. Center Hinge

B C

A. Flat-Head Handle Screws B. Refrigerator Drawer Handle

Drawer Front Removal Drawer Front Replacement

A. Loosen 4 Door Bracket Screws

A. Flat-Head Handle Screws B. Freezer Drawer Handle

Door Closing and Door Alignment

¹⁄₄"

1/4

The base grille covers the leveling screws and roller assemblies located at the bottom of the refrigerator cabinet below the freezer door or drawer. Before making adjustments, remove the base grille and move the refrigerator to its nal location.

1. Remove the two screws fastening the base grille to the

cabinet, and set the screws aside. Grasp the grille and pull it toward you.

2. Move the refrigerator to its nal location. NOTE: To allow the refrigerator to roll easier, raise the

leveling legs off the oor by turning the leveling screws counterclockwise. The front rollers will be touching the oor.

3. So the doors will close easier, use a 1/4" hex driver to turn both leveling screws clockwise. This will raise the front of the refrigerator tilting it slightly downward to the rear. Turn both leveling screws the same amount.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws. This makes it easier to turn the screws.

6. Make sure the refrigerator is steady. If the refrigerator seems

unsteady or rolls forward when the door or drawer is opened adjust the leveling screws. Using a 1/4" hex driver, turn the leveling screw on each side clockwise until the rollers are up and the leveling feet are rmly against the oor.

7. Replace the base grille by aligning the holes in the grille with

the holes in the cabinet and fasten using the screws removed in Step 1.

1/4

¹⁄₄"

A. Leveling screw B. Front roller

4. Open and close the doors to make sure they close as easily as you like. If not, increase the tilt by turning both leveling screws clockwise. It may take several turns of the leveling screw to allow the doors to close easier.

5. Check for door alignment. If one door is lower than the other, adjust the leveling screw, on the lower side of the refrigerator. Using a 1/4" hex driver, turn the screw clockwise to raise that side of the refrigerator until the doors are aligned. It may take several turns of the leveling screw to raise the refrigerator.

REFRIGERATOR USE

Opening and Closing Doors

(French door models)

There are two refrigerator compartment doors. The doors can be opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

■ When the left-hand refrigerator door is opened, the hinged

seal automatically folds inward so that it is out of the way.

■ When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A. Hinged seal

Using the Controls

Electronic Temperature Control

Freezer

7 is the coldest

7 is the coldestrecommended setting 4

Humidity Control

On O

Press if moisture appears

Refrigerator

Scroll Down for Cooling O

Electronic Temperature Control

Freezer

7 is the coldest

7 is the coldestrecommended setting 4

Humidity Control

On O

Press if moisture appears

Refrigerator

Scroll Down for Cooling O

Your model may have either Electronic or Digital Controls.

IMPORTANT:

■ Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a higher (colder) than recommended setting will not cool the compartments any faster.

■ The recommended settings should be correct for normal

household refrigerator use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is rm.

■ If the temperature is too warm or too cold in the refrigerator

or freezer, rst check the air vents to be sure they are not blocked before adjusting the controls.

Electronic Controls

For your convenience, the temperature controls are preset at the factory. When you rst install your refrigerator, make sure the controls are still set to the recommended setting as shown.

Style 1

Recommended Setting “4”

Adjusting Controls

If you need to adjust the temperature in either the refrigerator or freezer compartment, use the settings listed in the chart below as a guide.

To adjust the temperature:

Style 1 – Press the up or down arrow touch pads. Style 2 – Press the plus or minus sign touch pads.

Except when rst turning on the refrigerator, do not adjust the control more than one setting at a time. Wait 24 hours between adjustments for the temperature to stabilize.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR Control one

setting higher

FREEZER too warm/too little ice

FREEZER Control one setting higher

REFRIGERATOR too cold REFRIGERATOR Control one

setting lower

FREEZER too cold FREEZER Control one setting

lower

Digital Controls

For your convenience, your temperature controls are preset at the factory. When you rst install your refrigerator, make sure the controls are still set to the Initial settings as shown.

Initial Settings

Style 2

Recommended Setting “4”

To Turn Off/On: Style 1 – Press the freezer minus sign touch pad until a dash (-)

appears in both the refrigerator and freezer displays. Neither compartment will cool. Style 2 – Press the freezer down arrow touch pad until a dash

(-) appears in both the refrigerator and freezer displays. Neither compartment will cool.

Humidity Control (on some models)

The humidity control turns on a heater to help reduce moisture on the door hinge seal. Use in humid environments or when you notice moisture on the door hinge seal. The refrigerator uses more energy when Humidity Control is on.

■ Press the control to ON when the environment is warm and

more humid, or if you notice moisture on the door hinge seal.

■ Press the control to OFF to save energy when the

environment is less humid.

IMPORTANT: When the power is on, the temperature display shows the set point temperature of the compartment.

To Turn Your Refrigerator Off/On:

■ Press both the freezer and refrigerator (+) touch pads

repeatedly until “OFF” appears in the displays. Allow a few seconds for the refrigerator to shut off. Neither compartment will cool.

■ Press both the refrigerator and freezer (-) touch pads to turn

on the refrigerator.

Adjusting Digital Controls

The REFRIGERATOR control adjusts the refrigerator compartment temperature. The FREEZER control adjusts the freezer compartment temperature.

If you need to adjust the temperature in either the refrigerator or freezer compartment, use the settings listed in the chart as a guide.

To Adjust Set Point Temperatures:

The rst touch of the (+) or (-) touch pad displays the current temperature set point.

■ Press the (+) or (-) touch pads until the desired temperature

set point is displayed.

NOTE: Except when rst turning on the refrigerator, do not

adjust either temperature control more than one setting at a time. Wait 24 hours between adjustments for the temperature to stabilize.

Additional Digital Control Center Features

PowerCold

The PowerCold® feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room temperatures.

■ Press the PowerCold

refrigerator to the lowest temperature settings. Press the PowerCold® touch pad again to return to the normal refrigerator set point.

NOTE: The PowerCold® feature will automatically shut off in approximately 12 hours.

touch pad to set the freezer and

Max Ice

The Max Ice feature assists with temporary periods of heavy ice use by increasing ice production.

■ Press the Max Ice touch pad to set the freezer to the lowest

temperature setting. Press the Max Ice touch pad again to return to the normal freezer set point.

NOTE: When Max Ice is on, the (+) and (-) pads for the freezer control will not operate. The Max Ice feature will automatically shut off in approximately 24 hours.

Temp Alarm

The Temp Alarm feature provides temperature information in the event of a power outage.

Power outage: During a power outage, if the temperatures in the refrigerator and freezer compartments exceed normal operating temperatures, the highest temperature reached will be displayed.

■ Press the Temp Alarm touch pad until the indicator light is

lit, to turn on this feature. Press and hold Temp Alarm for 3 seconds until the indicator light goes off to turn off this feature.

Temp Alarm: An alarm will sound repeatedly if the freezer or refrigerator compartment temperatures exceed normal operating temperatures for an hour or more.

The temperature displays will alternately show the current temperatures and the highest temperatures the compartments reached.

■ Press the Temp Alarm touch pad once to stop the audible

alarm and alternating temperature displays. The Temp Alarm light will continue to ash until the refrigerator returns to the set temperature.

Door Alarm

The Door Alarm feature sounds a chime every few seconds when the refrigerator door has been left open for 5 continuous minutes. The chime will sound until the door is closed or Door Alarm is turned off.

■ Press the Door Alarm touch pad to turn this feature on or off.

The indicator light will be lit when the Door Alarm feature is on.

Humidity Control

The Humidity Control feature turns on a heater to help reduce moisture on the door hinge seal. Use in humid environments or when you notice moisture on the door hinge seal. The refrigerator uses more energy when Humidity Control is on.

■ Press Humidity Control when the environment is warm and

more humid, or if you notice moisture on the door hinge seal. The indicator light will be lit when humidity control is ON.

■ Press Humidity Control to save energy when the environment

is less humid.

Filter Reset

The Filter Reset control allows you to restart the water lter status tracking feature each time you replace your water lter. See

“Water Filtration System.”

■ Press and hold the Filter Reset touch pad for 3 seconds, until

the Order or Replace light turns off.

Digital Control User Preferences

The control center allows you to set user preferences, if desired.

Temperature Display (F_C)

This preference allows you to change the temperature display. F - Temperature in degrees Fahrenheit C - Temperature in degrees Celsius

Alarm (AL)

This preference allows you to turn off the sound of all alarms. ON - You will hear the alarm sound. OFF - You will not hear the alarm sound.

To Access the User Preferences Menu:

1. Press and hold the Door Alarm touch pad for 3 seconds. The

preference name will appear in the Freezer display and the preference status (F or C) or (ON or OFF) will appear in the Refrigerator display.

2. Use the Freezer (+) or (-) touch pads to scroll through the preference names. When the desired preference name is displayed, press the Refrigerator (+) or (-) touch pads to change the preference status.

3. Set your preferences by pressing and holding the Door Alarm touch pad for 3 seconds, or by shutting the refrigerator compartment door.

Crisper Humidity Control

You can control the amount of humidity in the moisture-sealed crisper. Depending on your model, adjust the control to any setting between FRUIT and VEGETABLES or LOW and HIGH.

FRUIT/LOW (open) for best storage of fruits and vegetables with skins.

VEGETABLES/HIGH (closed) for best storage of fresh, leafy vegetables.

Ice Maker

IMPORTANT: Flush the water system before turning on the ice maker. See “Water Dispenser.”

Turning the Ice Maker On/Off

To turn the ice maker ON, simply lower the wire shutoff arm. To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click. NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will ll the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position. Do not force the wire shutoff arm up or down.

Remember

■ Allow 24 hours to produce the rst batch of ice. Discard

the rst three batches of ice produced. Allow 3 days to completely ll the ice storage bin.

■ The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

■ Do not store anything on top of the ice maker or in the ice

storage bin.

Water Dispenser

IMPORTANT:

■ After connecting the refrigerator to a water source or replacing

the water lter, ush the water system. Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to ow. Once water begins to ow, continue depressing and releasing the dispenser paddle (5 seconds on, 5 seconds off) until a total of 4 gal. (15 L) has been dispensed. This will ush air from the lter and water dispensing system, and prepare the water lter for use. Additional ushing may be required in some households. As air is cleared from the system, water may spurt out of the dispenser.

NOTE: After 5 minutes of continuous dispensing, the dispenser will stop dispensing water to avoid ooding. To continue dispensing, press the dispenser paddle again.

■ Allow 24 hours for the refrigerator to cool down and chill

water. Dispense enough water every week to maintain a fresh supply.

Dispensing Water

1. Hold a container under the dispenser spout while pressing the

dispenser pad.

2. Release the dispenser pad to stop dispensing.

NOTE: Turn off the ice maker before removing the ice storage bin

to serve ice or to clean the bin. This will keep the ice cubes from dropping out of the ice maker and into the freezer compartment. After replacing the ice storage bin, turn on the ice maker.

Ice Production Rate

■ The ice maker should produce a complete batch of ice

approximately every 3 hours.

■ To increase ice production, lower the freezer and refrigerator

temperature. See “Using the Controls.” Wait 24 hours between adjustments.

+ 33 hidden pages

Maytag MFF2258FEZ Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual