Maytag MEW6630DDQ User Manual [en, es, fr]

INSTALLATION

INSTRUCTIONS

Built-In 27²²²² &30²

²

²²

Electric Wall Ovens

403 WEST FOURTH STREET, NORTH

NEWTON, IA 50208

27²²²² SINGLE WALL OVEN

111/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (Must Support142 lbs.)

DIMENSIONS

inches cm

A 27 MIN 68.58
B 24 MIN 60.96
C277/8+
D 24.0 60.96
E251/2+
F 28 1/4 71.76
G 26 3/4 67.95
H 24 7/16 62.07
I 4 to 33 10.2 to 83.8

1/16 70.80

1/16 64.77

27²²²² DOUBLE WALL OVEN

111/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (Must Support250 lbs.)

DIMENSIONS

inches cm

A 27 MIN 68.58
B 24 MIN 60.96
C 50.0 +
D 24.0 60.96
E251/2+
F 50 1/14 127.64
G 26 3/4 67.95
H 24 7/16 62.07
I 4 to 12 10.2 to 30.5

1/16 127.0

1/16 64.77

30²²²² SINGLE WALL OVEN

111/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (Must Support142 lbs.)

DIMENSIONS

inches cm

A 30 MIN 76.20
B 24 MIN 60.96
C277/8+
D 24.0 60.96
E281/2+
F 28 1/4 71.76
G 29 3/4 75.57
H 24 7/16 62.07
I 4 to 33 10.2 to 83.8

1/16 70.80

1/16 72.39

30²²²² DOUBLE WALL OVEN

111/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (Must Support250 lbs.)

DIMENSIONS

inches cm

A 30 MIN 76.20
B 24 MIN 60.96
C 50.0 +
D 24.0 60.96
E281/2+
F 50 1/4 127.64
G 29 3/4 75.57
H 24 7/16 62.07
I 4 to 12 10.2 to 30.5

1/16 127.0

1/16 72.39

SINGLE WALL OVEN

DOUBLE WALL OVEN

30²²²² WALL OVEN UNDER COUNTER

111/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (Must Support 142 lbs.)

A 25 63.50
B 24 MIN 60.96
C277/8+
D 24.0 60.96
E 28 1/2 72.39
F 28 1/4 71.76
G 29 3/4 75.57
H 24 7/16 62.07
I 36 91.44
J11/2 3.81

30²²²² WALL OVEN

* * COOKTOPS inches cm

K Electric 3 1/8 MIN 7.9 MIN
K Induction 3 1/8 MIN 7.9 MIN
K 4 Burner Gas Stamped Top 4 13/16 MIN 12.2 MIN
K 4 Burner Gas Glass Top 4 13/16 MIN 12.2 MIN

NOTE:

* Hole must be cut as close to corner of cabinet as possible.

** See dealer for approved cooktops.

DIMENSIONS

inches cm

1/16 70.80

UNDER COUNTER WALL OVEN

NOTES

Z Do not block air intake slots along bottom of oven.
Y Gas or electriccooktops may be installed overovens.

See cooktop installation instructionsfor cutout size.

W Electrical connection forelectric cooktopmust be in adjacent

accessiblelocation.Cooktop and wall oven must be on separate
120/240 or 120/208 volt 60 Hz AC circuits.

8101P603-60

(09-03-00)

CAUTION

For European style cabinets (flush front) the required
clearance for operation of the oven door is minimum
spacing of 7/8² between the cutout and the door, hinge
or drawer of the cabinet.

Electrical Connections

Unit to be properly circuit protected and wired according
to local electrical code and National Electrical Code.

It is advisable that the electrical wiring and hookup be
accomplished by a competent electrician.

Some built-in cabinets may not be wide enough, due to
their construction, to allow this installation.

1. Cut hole in cabinet to mount oven. Cutout in cabinet
should be level and straight.

NOTE: There are no provisions to level the unit after it
is installed. An oven that is not level could cause poor
baking results.

2. Install plywood floor as shown.

3. Attach unit to the cabinet with four No. 8 x 1² screws
supplied with unit inside of envelope containing these
instructions. Pre-drill holes in cabinet for attachment
screws using 1/8² drill. Oven mounting holes are
provided in side trim.

4. See instructions at right for electrical hook-up.

5. See Use and Care Manual for operating instructions.

Installing Bottom Trim Piece

120/240 VAC or 120/208 VAC 60 Hz. See serial plate on
front of unit for power requirements.

The neutral of this unit is grounded to the frame through
the green or solid grounding wire. (The green and the
white wires are twisted together at the termination of the
conduit.) If used on new branch-circuit installations (1996
NEC), mobile homes, recreational vehicles, or in an area
where local codes prohibit grounding through the neutral
conductor, untwist or disconnect the green wire and
connect the green wire to ground in accordance with local
code. Connect the white neutral to the service neutral.
Connect all wires to the branch circuit with approved
connectors. Use copper or aluminum wire. If aluminum
wire is used, use connectors recognized for joining
aluminum to copper.

The chart below recommends the minimum circuit
protection and wire size if the appliance is the only unit on
the circuit.

K.W.RATING

ON SERIAL PLATE

0-- 4.8

4.9 -- 6.9

7.0 -- 9.9

10.0 -- 11.9

12.0 -- 14.9

RECOMMENDED MINIMUM

CIRCUIT PROTECTION

IN AMPERS

20
30
40
50
60

WIRE SIZE

(AWG)

12
10

8
8
6

Service

Interrupt the source of electricity to the unit when
attempting to repair or service the oven. Failure to do this
could result in a dangerous or even fatal shock.

IMPORTANT - SAVE FOR LOCAL ELECTRICAL INSPECTOR’S USE