Maytag MEW6630DDB, MEW6630DDS, MEW6630DDQ, MEW6630DDW Dimension Guide

www.dexpress.com DIMENSION EXPRESS Fax on Demand [phone]

		This Data Sheet Includes Information On
			Maytag
•			Product Model Number (s):		•
			30" Electric Double Ovens:
		MEW6630DDB, MEW6630DDS, MEW6630DDQ and
			MEW6630DDW
•			Dimensions (Actual Size)		•
			Cutout width:	28 1/2"
			Cutout height: 50"
			Cutout depth: 24"
			Minimum cabinet width: 30"
	Recommended cutout location from floor : 4" - 12"
			Distance from face of cabinet to
		outer edge of open doors (Door swing): 20 1/2"
			Distance from face of cabinet to
			front of closed door handle: 15/16"
			Overall unit width: 29 3/4"
			Overall unit height: 50 1/4"
			Penetration into cabinet: 23 1/2"
			Oven overlap distances when using
			cutout dimensions listed above:
			Top overlap: 1/4"
			Bottom overlap: 0"
			Right side overlap: 5/8"
			Left side overlap: 5/8"
	•		Additional Information		•

•Cutout in cabinet should be level and straight. There are no provisions to level the unit after it is installed.

•Do not block air intake slots along bottom of oven.

•Construct 5/8" minimum plywood floor flush with bottom of opening. Floor must be level and straight and capable of supporting 250 lbs.

•A three-wire, single phase, A.C. 120/208-240 volt, 60Hz cycle electrical system protected by a 40 amp fuse or comparable circuit breaker must be provided . 7/8" O.D. flexible cable 4 feet long is furnished by manufacturer. Mount junction box in area under plywood floor if adequate lower cabinet space is available. Locate 1 1/4" conduit access hole in the back right hand side of the plywood floor.

•For European style cabinets (flush front) the required clearance for operation of the oven door is a minimum spacing of 1" between the cutout and the door, hinge or drawer of the cabinet.

See page 2 for additional information

Subject to change without notice. This system is designed to
be updated daily if necessary. Dimension Express is not
responsible for use of superseded, voided, or outdated data
sheets. Because of the difficulty or impracticability of deter-
mining actual damages, liability of Dimension Express shall
not exceed $50.00.
Copyright © Dimension Express, 2003.	213

30"

28 1/2"
			24"

Cabinet Opening

(not to scale)

50"

Provide for

120/208-240 volt 4" - 12" electrical

connection in this area.

Overall Dimensions

(not to scale)

50 1/4"

23 1/2"

29 3/4"

15/16"

• NEVER reuse Data Sheets. Data Sheets are subject to change without	• Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily,	• Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data	• Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks	BN207.5 • A213B276 • • 031211 • 82843 • 85637
associated with reusing old Data Sheets.

www.dexpress.com					This Data Sheet Includes Information On
DIMENSION EXPRESS					Maytag
	Page 2			•	Product Model Number (s):	•
Fax on Demand [phone]
					30" Electric Double Ovens:
					MEW6630DDB, MEW6630DDS, MEW6630DDQ and
					MEW6630DDW
Additional Information:

		Cabinet door
	1 1/2"	There must be 1"
	minimum
		minimum between
	wide rail
		bottom of cabinet
		door and top of
		oven console.
		Oven Control Console

							1" minimum from oven
							opening floor to top of
							cabinet door or drawer
Oven opening floor							front.

Cabinet door or drawer front

Side View (not to scale)

Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.

Copyright © Dimension Express, 2003.

276

• NEVER reuse Data Sheets. Data Sheets are subject to change without	• Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily,	• Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data	• Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks	BN207.5 • A213B276 • • 031211 • 82843 • 85637
associated with reusing old Data Sheets.