Maytag MEW6530DDB, MEW6527DDB, MMW5530DAW, MMW5530DAB, MEW6630DDS Owner’s Manual

...
I _&YI'AG
Form No. A/04/03
Safety
Care & Cieartinff ................... 15-17
Self-CHeanOver] CUeaningProcedures
Part No. 8112P217-60
Guia del Usuario ......................... 44
installer: Pleaseleave this manual with this appfiance. Consumer: Hease read and keep this manual for future
reference. Keepsales receipt and/or canceled check as proof ot purchase.
Model Numbel Seria Number
Date of Purchase
Maytag Customer Assistance
]-800-688-9900 USA ]-800-688-2002 Canada
1-800-688-208Q ( U.S.TTYfor hearing or speech irrlpaired_ (Mon.Wri., 8 am-8 pm EasternTime)
Internet: http:!/wvwv.m aytag.com in our continuing effort to improve the quafity and perfor-
mance of our cooking products, it may be necessaryto make changes to the appfiance without revising this g uide.
For sendce #_fermade#, see page 21.
To ensere proper and safe operation: Appliance must be properly installed and grounded by a qualified technician. Do not attempt to adjust, repair, service, or replace any part of your appliance unless it is specifi- cally recommended in this guide. All other servicing should be referred to a qualified servicer.
Always disconnect power to appliance before servicing.
To Prevent Fire or Smoke
* Be sure all packing materials are removed from the
appliance before operating it. Keep area around appliance clear and free from
combustible materials. Flammable materials should not be stored in an oven.
Many plastics are vulnerable to heat. Keep plastics away from parts of the appliance that may become
warm or hot. To prevent grease fires, do not let cooking grease or
other flammable materials accumulate in or near the appliance.
iMPORTANT SAFETY INSTRUCTIONS
Warning and Important Safety Instructions appearing in this guide are not meant to cover all possible conditions and situations that may occur. Common sense, caution, and care must be exercised when installing, maintain-
ing, or operating the appliance.
Always contact your dealer, distributor, service agent, or
manufacturer about problems or conditions you do not understand.
Recognize Safety Symbols, Words, Labels
WARNnNG' Hazards or unsafe practices which COULD resu!t !n severe persona! injury 0r death.
CA[JTUON _ Hazards or unsafe practices wh!ch
COULD result in mino_ personal injury.
Read and follow aH instructions before using this appmiance to prevent the potential risk of fire, electric shock, personal injury or damage to the appliance as a result of improper usage of the appliance. Use appliance only for its intended purpose as described in this guide.
In Case of Fire
Use dry chemical or foam-type extinguisher or baking soda to smother fire or flame. Never use water on a
grease fire.
1.Turn off appliance to avoid spreading the flame.
2oNEVER pick up or move a flaming pan.
3. Smother fire or flame by closing the oven door.
Child Safety
above an app!iance. Children cJJmbjng on the appli- ance Or on the appliance d00rt0 reach items could be
sedous!y injured,
NEVER leave children alone or unsupervised near the appliance when it is in use or is still hot. Children
should never be allowed to sit or stand on any part of the appliance as they could be injured or burned.
Children must be taught that the appliance and utensils in it can be hot. Let hot utensils cool in a safe
place, out of reach of small children. Children should be taught that an appliance is not a toy. Children
should not be allowed to play with controls or other
parts of the unit.
About Your Appliance
above. Misuse of appDnce doors, such as stepping, leaning or sitting On the door, may resu!t in possible
serious injuries,
To prevent potential hazard to the user and damage to the appliance, do not use appliance as a space heater
to heat or warm a room. Also, do not use the oven as a
storage area for food or cooking utensils. Do not obstruct the flow of air by blocking the oven
vent.
DO NOT TOUCH HEATING ELEMENTS OR INTERIOR SURFACES OF OVEN. Heating elements may be hot even though they are dark in color, hterior surfaces of
any oven become hot enough to cause burns. During and after use, do not touch, or let clothing or other
flammable materials contact heating elements or interior surfaces of oven until they have had sufficient
time to cool. Other surfaces of the appliance may
become hot enough to cause burns - among these surfaces are: oven vent openings and surfaces near
these openings, oven doors, windows of oven doors.
Do not touch a hot oven light bulb with a damp cloth
as the bulb could break. Should the bulb break, disconnect power to the appliance before removing
bud to avoid electrical shock.
A fan should be heard during some bake, convect
bake, convect roast, and all broil and cleaning opera-
tions. If you do not hear the fan, call an authorized
servicer.
NEVER use aluminum foil to cover an oven rack or oven bottom. Misuse could result in risk of electric
shock, fire, or damage to the appliance. Use foil only as directed in this guide.
Cooking Safety
Never heat an unopened food container in the oven. Pressure build-up may cause container to burst resulting in serious personal injury or damage to the appliance.
Use dry, sturdy potholders. Damp potholders may cause burns from steam. Dish towels or other substi-
tutes should never be used as potholders because they
can trail across hot elements and ignite or get caught on appliance parts.
Wear proper apparel. Loose fitting or long hanging- sleeved apparel should not be worn while cooking.
Clothing may ignite and cause burns if garment comes in contact with heating elements.
Always place oven racks in the desired positions while
oven is cooL Slide oven rack out to add or remove
food, using dry, sturdy potholders. Always avoid
reaching into the oven to add or remove food. If a rack must be moved while hot, use a dry potholder. Do not let potholder contact hot element in oven.
Use care when opening the oven door. Let hot air or
steam escape before removing or replacing food.
PREPARED FOOD WARNUNG: Follow food manufacturer's instructions. If a plastic frozen food
container and/or its cover distorts, warps, or is other-
wise damaged during cooking, immediately discard the food and its container. The food could be contami-
nated. Do not allow aluminum foil or meat probe to contact
heating element.
Always turn off all controls when cooking is com-
pleted.
Utensil Safety
Follow the manufacturer's directions when using oven cooking bags.
This appliance has been tested for safe performance
using conventional cookware. Do not use any devices or accessories that are not specifically recommended
in this manual. Do not use add-on oven convection
systems. The use of devices or accessories that are not
expressly recommended in this guide can create
serious safety hazards, result in performance prob-
lems, and reduce the life of the components of the appliance.
Only certain types of glass, glass/ceramic, ceramic, earthenware, or other glazed utensils are suitable for oven service without breaking due to the sudden change in temperature. Follow utensil manufacturer's instructions when using glass.
Cmeaning Safety
Turn off all controls and wait for appliance pars to cool before touching or cleaning. Clean with caution. Use care to avoid steam burns if a wet sponge or cloth is used to wipe spills on a hot surface. Some cleaners can produce noxious fumes if applied to a hot surface.
Clean only parts listed in this guide.
Self-Clean Oven
during the se!f:cJean cYCle,
Do not clean door gasket. The door gasket is essential for a good seal Care should be taken notto rub, damage, or move the gasket.
Do not use oven cleaners or oven liners of any kind in or around any part of the self-clean oven.
Before self-cleaning the oven, remove broiler pan, oven racks and other utensils, and wipe off excessive spillovers to prevent excessive smoke or flare ups.
important Safety Notice and
The California Safe Drinking Water and Toxic Enforce- ment Act of 1986 (Proposition 65} requires the Governor of California to publish a list of substances known to the State of California to cause cancer or reproductive harm, and requires businesses to warn customers of potential exposures to such substances.
Users of this appliance are hereby warned that when the oven is engaged in the self-clean cycle, there may be some low-level exposure to some of the listed substances, including carbon monoxide. Exposure to these substances can be minimized by properly venting the oven to the outdoors by opening the windows and/ or door in the room where the appliance is located during the self-clean cycle.
UMPORTANT NOTUCE REGARDUNG PET BURDS:
Never keep pet birds in the kitchen or in rooms where the fumes from the kitchen could reach. Birds have a
very sensitive respiratory system. Fumes released during an oven self-cleaning cycle may be harmful or fatal to birds. Fumes released due to overheated cooking oil, fat, margarine and overheated non-stick cookware may be equally harmful
refer to the use and care guide packed in the micro- Note: For microwave oven operation (select modelsD
wave oven.
Save These instructions for Future Reference
3
@
Control Panel
A B CDE FG
$ K L M N O
The contro[ pane[ is designed for easein programming. Thedispiaywindow on thecontro[ shows time ofday,timer and ovenfunctions.
Contro[ pane[ shown inciudes Convect and other mode[ specific features. (Styiing may vary depending on modeL)
m
A
Bake Broi]
[}
c ¸
Convect Bake (select models]
Keep Warm
E
Convect Roast (select models}
Clean
F
CANCEL
Number Pads Oven Light
$
Timer One/Two
Clock
K
L
Cook & Hold
M
Delay (select models)
N
Favorite
ii
O
Autoset
Use for baking and roasting. Use for broiling and top browning. Use for convection baking.
Use to keep cooked food warm in oven. Use for convection roasting.
Use to set self-clean cycle. Cancelsail operations exceptTimerand
Clock. Use to set time and temperature.
Useto turn the upper orlower ovenlight on or off.
Sets the timer. Sets the Clock.
Bakes for a presettime,then holds food warm for 1hour.
Programs the oven to start baking at a later time.
Use to set and savea specific Cook & Hold procedure.
Use to quickly set temperatures.
Using the Touchpads
" Pressthe desired pad. " Pressthe number pads to enter time or temperature. , Press the Autoset pad to enter temperature. " A beep will sound when any pad is touched. " A double beep will sound if a programming error occurs.
NOTE: Four seconds after entering the number, the time or temperature will automatically be entered. If more than
30 seconds elapse between touching a function pad and the number pads, the function will be canceled and the
display will return to the previous display.
The clock can be set to display time in a 12-hour or 24-hour format. The clock is set at the factory for the 12-hour format.
To change the clock to 24-hour format:
1, Pressand hold the CANCEL (Upper Oven
CANCEL for double wall ovens) and Favorite pads for three seconds,
, 12 Hr flashes in the display,
2, Pressthe Autoset pat to select 24 Hr; press
again to select 12 Hr,
3, Set the time of day following the directions in
the To Set the Clock section,
H
1 2 3
4 5 6
7 8 9
Autoset
4
@
To set the Clock:
1. Press the Clock pad. , The time of day flashes in the display.
2. Press the appropriate number pads to set the time of day. , Colon flashes in the display.
3. Press the Clock pad again or wait four seconds. , The colon will remain on.
When electrical power is supplied or after a power interrup-
tion, the last clock time before power was interrupted will flash.
To recall the time of day when another time function is
showing, press the Clock pad. Clock time cannot be changed when the oven has been
programmed for Delay cook or clean or Cook & Hold.
To canceJ the CJock display:
[f you do not want the time of day to display: Press and hold the CANCEL and Clock pads for
three seconds. The time of day will disappear from the display.
When the clock display is canceled, press the
Clock pad to briefly display the time of day............................................
When the clock display is canceled, after 15minutes, the oven
control will go into Standby Mode to save energy. The display
will be blank and the oven light will not operate. To "wake up"
the control from Standby Mode, pressany touchpad. A double beep will sound.
To restore the Clock display:
Press and hold the CANCEL and Clock pads for three sec- onds. The time of day will reappear in the display.
The timer can be set from one minute (00:01} up to 99 hours
and 59 seconds (99:59}.
The timer can be used independently of any other oven
activity. Itcan also be set while another oven function is operating.
The Timer does not control the oven. It only controls a
beeper.
_ Note: The touchpads and oven door cannot be locked if
To set the Timer:
1. Press the Timer pad. ° 00:00and TIMER iconflash in the display.
2. Press the appropriate number pads until the correct time appears in the display.
° The colon and TIMER icon will continue to flash.
3. PressTimer pad again or wait four seconds. ° The colon stops flashing and the time begins counting
down.
° The last minute of the timer countdown will be displayed
in seconds.
4. At the end of the set time, one long beep will sound and "End" wii[ be displayed.
5. Pressthe Timer pad to clear the display.
To cancel the Timer:
1. Pressand hold the Timer pad for three seconds.
OR 0
2. Pressthe Timer pad and press '0' using the number pads.
Locking the Centre[
and Oven Door
The touchpad and oven door can be locked for safety, cleaning, or to prevent unwanted use. The touchpads will not
function when locked. [f the oven is currently in use, the touchpads and door cannot
be locked. The current time of day will remain in the display when the
touchpads and door are locked.
To lock:
1. Pressand hold the CANCEL and Cook & Hold pads for three seconds.
° OFFappears in the display ° The LOCK icon flashes while the door is
locking.
To unlock:
Press and hold the CANCEL and Cook & Hold pads for three seconds. OFFdisappears from the display.
the oven temperature is 400° For above.
Fault Codes
The BAKEor LOCK icon mayflash rapidly in the display to alert you if there is an error or a problem. If the BAKE or
LOCK icon flashes in the display, press CANCEL pad. If the BAKE or LOCK icon continues to flash, disconnect power to
the appliance. Wait a few minutes, and then reconnect power. If the icon flashing still continues, disconnect power to
the appliance and caii an authorized servicer.
5
To set Bake:
1. Press the Bake pad. Bake , The BAKE icon will flash.
, 000 wifl flash in the dispiay.
2. Sdect the oven temperature. Pressthe Autoset pad for 350°F or the appropriate number pads.
, Each addidonai press of the Autoset pad will increase
the temperature by 25°.
, The oven temperature can be set from 170° to 550°.
3. Press Bake pad again or wait four seconds.
, The BAKE icon will stop flashing and Hightin the dispiay. , The PREHEATicon will Hightin the dispiay.
° 100° or the actual oven temperature if over 100° Fwill
dispiay. It wifl rise in 5°increments until the preset temperature is reached.
4. Allow the oven to preheat for 8-15 minutes.
° When the set oven temperature is reached, one long
beep will sound.
° The set temperature will display. ° The PREHEATicon will turn off.
Autoset
Baking Differences Between Your
and New Oven
It is normal to notice some baking time differences between a new ovenandan oldone, See"Adjusting the OvenTemperature"
on page 12.
Baking with Convection
(select models}
When convection baking, enter your normal baking tempera- ture. The control will automatically reduce the set oven
temperature by 25°. To set Convect Bake:
1,
Pressthe Convect Bake pad. ° The BAKEand FAN icons will flash
° 000 will flash in the display.
2. Select the oven temperature. Pressthe Autoset pad for 350° For the appropriate number pads.
° Eachadditional pressof the Autoset pad will increase
the temperature by 25 degrees. The oven temperature can be set from 170° to 550°.
3. Press Convect Bake pad again or wait four seconds.
° The BAKEicon will stop flashing. ° The PREHEATicon will light in the display.
, 100° or the actual oven temperature if over 100° Fwill
display. It will rise in 5° increments until the preset temperature is reached.
° The FAN icon will start to rotate.
Autoset
° To recall set temperature during preheat, press Bake pad.
5. Place food in the oven.
8. Check cooking progress at the minimum cooking time. Cook longer if needed.
7. When cooking is finished, press CANCEL pad. ('_ANCEh
8. Remove food from the oven.
Baking Notes:
° To change the oven temperature during cooking, press
Bake, then press the Autoset or appropriate number pads until the desired temperature is displayed.
° To change the oven temperature during preheat, press the
Bake pad twice, then press the Autoset pad or appropriate number pads until the desired temperature is displayed.
° If you forget to turn off the oven, it will automatically turn
off at the end of 12 hours. Ifyou wish to deactivate this feature, see page 11.
° Foradditional baking and roasting tips, see "Cooking Made
Simple" booklet.
4. Allow the oven to preheat for 8-15 minutes. ° When the set oven temperature is reached, one long
beep will sound.
° The PREHEATicon will turn off. ° The set temperature will display.
° To recall the set temperature during preheat, press the
Convect Bake pad.
5. Placefood in the oven.
8. Check cooking progress at the minimum cooking time. Cook longer if needed.
7. When cooking is finished, press CANCEL pad.
8. Removefood from the oven.
6
Roasting With Convection
(:select models)
When convection roasting, enter your normal roasting time
and temperature. The controHwill automatically prompt you to check the food for aloneness at 75% of the set time.
, When convection roasting, the cooking time must be set
before setting the temperature.
° If your recipe requires a preheated oven, add 15 minutes
to the cooking time programmed.
, Roasting times can vary with different cuts of meat. ° Refer to "Cooking Made SimpW' booHet for suggested
roasting temperatures and times.
To set Convect Roast:
1. Press the Convect Roast pad. ° The ROASTand FAN icons will flash
, 00:00will flash in the dispDy. ° 000 Hightsin the display.
2. Enter the roasting time using the number pads. ° Time can be set from 10 minutes (00:10) to 11hours,
59 minutes (11:59). , Press Convect Roastagain or wait 4 seconds. , 'Roast' flashes in the display.
3. Select the oven temperature. Pressthe Autoset pad for 350° For the appropriate
number pads. ° Each additional press of theAutoset pad will increase
the temperature by 25°.
, The oven temperature can be set from 170° to 550°.
Autoset
Press Convect Roast pad again or wait four seconds. ° The ROASTicon will stop flashing and light in the
display.
, 100° or the actual oven temperature will display. It will
rise in 5° increments until the preset temperature is reached.
, The FAN icon will start to rotate.
Allow the oven to preheat for 8-15 minutes.
° When the set oven temperature is reached, one long
beep will sound.
° To recall the set temperature during preheat, press the
Convect Roast pad.
6.
Placefood in the oven.
7.
When 750/0of the set cooking time has elapsed, the oven
light wi[[ turn on and 'Food' wi[[ flash in the display. Check
the cooking progress at this time. The oven light will
remain on until the Oven Light pad is pressed. Cook longer if needed.
Press the Convect Roast pad to recall the cook
° At the end of cook time, the oven will automatically keep
food warm for one hour.
8.
When cooking is finished, press CANCEL pad.
9.
Removefood from the oven.
7
Cook & Homd
When using the Cook & Homdoption, the oven begins to heat
immediateiy after the controi has been set. Then, the oven cooks for a specified iength of time. When that time has
eiapsed, the oven wiii keep the food warm for up to an hour then automaticaHHyturn off.
TO set Cook & Hold:
1. Press the Cook &Hoid pad. ° The HOLD icon wiii flash to indicate thatyou arein Cook &
Hoid programming.
° 00:00wiii flash in the dispiay.
2. Seiect the amount of time you want to cook by using the number pads.
° The HOLD icon continues to flash. ° The time wiii Hightin the dispiay.
° Time can be set from 00:10 to 11:59.
3. Press Bake,Convect Bake or Convect Roast (seiect modeis}
and seiect the oven temperature. Pressthe Autoset pad for 350° For the appropriate number pads.
° The desired cycie icon wiii flash. Bake ° The oven temperature can be set from 170° Fto 550° F.
4. Press the desired cycie pad again ORwait four seconds. ° The desired cycie icon wiii remain Hit.
° The cooking time wiii show in the dispiay. ° The PREHEATicon wiii show in the dispiay.
° The actuai oven temperature wiii be dispiayed
during preheat.
° The set temperature wiii dispiay when the oven is
preheated.
When the cooking time has elapsed:
° Four beeps wiii sound. ° The HOLD and WARM icons wiii Hight.
° 170°wiii dispiay. , Time of day wiii dispiay.
To cancel Cook & Hold at any time:
Pressthe CANCEL pad. Remove food from oven.
Delay Cook & Hold
Do not use delayed baking for highiy perishabHefoods such as dairy products, pork, pouHtry,oFseafood,
When using Delay, the oven begins to cook Haterin the day. Set the amount of time that you want to delay before the oven
turns on and how long you want to cook. The oven begins to
heat at the selected time and cooks for the specified length of
time,
Delay time can be set from 10 minutes (00:10} to 11 hours, 59
minutes (11:59}.
TO set a Delayed Cook & Hold eyde:
1,
Pressthe Delayor Delay 1 pad (select models}. In double waii oven models, press the Delay or
Delay 1(select models} pad once to program the
upper oven or twice to program the lower oven. , The DELAY icon flashes in the dispiay.
, 00:00 flashes in the dispiay.
Using the appropriate number pads,enter the amount of time
you want to deiay the start of the Cook &Hoid cycie.
Pressthe Cook & Hoid pad.
° The HOLD icon flashes. ° The DELAY icon flashes in the display.
, 00:00 flashes.
4,
Enterthe amount of timeyou want to cook using the number
pads.
5.
PressBake, Convect Bake or Convect Roast (seiect modeis}.
6.
Set the oven temperature desired by pressing the Autoset pad or the appropriate number pads.
° 350° will[ Hightwhen Autoset is pressed. Autoset
Delay 1
After one hour in HOLD WARM:
, The oven turns off automaticaiiy. ° HOLD and WARM icons go off.
° Remove food from oven.
° After fourseconds, the entered deiaytimewii[ appear inthe
dispiay.
° The HOLD icon turns off. ° The BAKEand DELAY icons remain lit to remind you that
a delayed Cook & Hold cycle has been programmed.
Note: ° Donot use Delayed Cook & Hold foritems thatrequire a
preheated oven, such as cakes, cookies, and breads.
° Donot use Delayed Cook & Hold if oven is already hot.
@
To set Broil:
1. Press the Broii pad. , The BROIL icon flashes.
, 00Oflashes. , SETflashes.
2. Press the Autoset pad once to set Hi broi[ or Autoset twice to set LO broil
. Hi or LO will[ bedispiayed.
Seiect Hi broi[ for norma[ broiiing. Seiect LO broi[ for How-temperature broihng of [onger cooking foods such
as pouitry.
3. After four seconds, the oven will[ start. , The BROIL icon will[ remain Hit. . Hi or LO will[ remain Hit.
8. Turn meat once about halfway through cooking.
7. When food is cooked, press the CANCEL pad. Removefood and broiler pan from the oven.
, The time of day will reappear in the display.
Broil @ores:
, For best results when broiling, use a pan designed for
broiling.
° Expect broil times to increase and browning to be
slightly lighter if appliance is installed on a 208-volt circuit.
, if more than 30 seconds elapse between pressing the
Broil pad and the Autoset pad, the oven wiil not be set and the display wiil return to the previous display.
° A cooling fan wiil automatically turn on during broiling, if
it does not operate, contact an authorized servicer.
, Hi is used for most broiling. Use LObroil when broiling
longer cooking foods. The lower temperature allows food to cook to the weil done stage without excessive
browning.
, Broil times may be longer when the lower broiling
4. For optimum browning, preheat broil element for 3-4 minutes before adding food.
5. Piace food in the oven. Leave oven door open about four inches (the first stop}.
, Food should be turned halfway through broiling time. ° For additional broiling tips and temperatures, refer to the
"Cooking Made Simple" bookleL
Broiling Chart
FOODS POSiTiON* _ FIRST SiDE SECOND SiDE
Beef
Steak, 1" thick, Medium
Well
Hamburgers, 3/4" thick, Medium
Well
Pork
Chops, 1/2" Chops, 1"
Ham Slice
Poultry LO Broil LO Broil Breast Halves 3 11-12 minutes 9-11 minutes
4o
40 40
4o
4o
3
4o
9 minutes
11 minutes
5 minutes 8 minutes
7 minutes
10 - 11 minutes
4 minutes
7 minutes
8 minutes 3-4 minutes 4-5 minutes
5-8 minutes
9-10 minutes
2-3 minutes
Seafood
Fish Steaks, buttered, 1" thick
* An "o" after the rack position number indicates that the offset rack should be used. Note: This chart is a suggested guide. The times may vary with the food being cooked.
8-10 minutes4o
9
(no turning}
Keep War
For safeHykeephg hot foods warm or for warmhlg breads and pHates=
To set Keep Warm:
1= Press the Keep Warm pad=
° The WARM icon flashes. ° 000 flashes in the dispHay= Autoset
2= SeHectthe Keep Warm temperature. Pressthe Autoset pad
or the appropriate number pads.
° 170°wiHHHightwhen the Autoset pad is pressed. ° Each press of the Autoset pad wiHHincrease the
temperature by 5°=
The KeepWarm temperature can be set from 145° to 190°= The WARM icon and the temperature wiHHbe dispHayed
wMHethe function is active.
Keep Warm Notes:
° ForoptimaHfood quaHity,oven cooked foods shouHdbe
kept warm for no Hongerthan 1 to 2 hours.
° To keep foods from drying, cover HooseHywith foiHor a Hid= ° To warm dinner rolls:
- cover forthsHooseHywith foiHand pHacein oven.
- press Keep Warm and Autoset pads.
- warm for 12-15 minutes.
° To warm pmates:
- pHace2 stacks of up to four pHateseach in the oven.
- press Keep Warm and Autoset pads.
- warm for five minutes, turn off the oven and Heave pHatesin the oven for 15 minutes more.
- use onHyoven-safe pHates,check with the manufacturer.
- do not set warm dishes on a cold surface as rapid temperature changes could cause crazing or
breakage.
To cancel Keep Warm:
1. Press the CANCEL pad.
2. Remove food from the oven.
10
@
Automatic Shut-Off/Sabbath
Mode
The oven vviHautomatically turn off after 12hours if you
acddentaHy Heaveit on. This safety feature can be turned off.
To cancel the 12=hour shut-off and run the oven
continuously for 72 hours: ........................
1. Press and hoM the Clock pad for three seconds ° "SAb" will be displayed and flash for five seconds.
° "SAb" will then be displayed continuously until turned
off or until the 72-hour time limit is reached.
° The BAKEicon will also be displayed if a bake cycle is in
use while the oven is in Sabbath Mode.
° All keys are inactive except CANCEL and Clock. All other
functions EXCEPTBAKE (Timer, Keep Warm, Clean,etc.} are locked out during the Sabbath Mode.
° A Cook & Hold can be programmed during the Sabbath
Mode, however a Delay Cook & Hold is not allowed.
To cancel the Sabbath Mode:
1. Press the CLOCK pad for three seconds. OR
2. After 72 hours, the Sabbath Mode will end. ° "SAb" will flash for five seconds.
Sabbath Mode Notes:
° Sabbath Mode can be turned on at any time with or
without the oven on.
° Sabbath Mode cannot be turned on if the keypads are
locked out or when the door is locked.
° Most prompts and messages and all beeps are
deactivated when Sabbath Mode is active.
° If the oven is baking when Sabbath Mode is set, the
BAKE icon will go out at the end of the baking cycb.
There will be no audible beeps.
° If the oven light is desired while in Sabbath Mode, it
must be turned on before the Sabbath Mode is started.
, When the Sabbath Mode is started, the temperature
display will immediately show the set temperature, rather than the actual oven cavity'temperature. No preheat
beep will sound.
, The self-dean cycle and automatic door lock do not
operate during the Sabbath Mode.
, Pressing CANCEL pad will cancel a Bake cycle, however
the control will stay in the Sabbath Mode.
, If power fails, the oven will power up in Sabbath Mode
with 72 hours remaining and no cycb active.
° The time of day will return to the display.
11
Adjusting the Oven Temperature
Oven temperatures are carefully tested for accuracy at the factory. It is normal to notice some baking or browning
differences between a new oven and an old one. As ovens get older, the oven temperature can shift.
You may adjust the oven temperature if you think the oven is
not baking or browning correctly. To decide how much to change the temperature, set the temperature 25 degrees
higher or lower than your recipe recommends, then bake.
The results of the first bake should give you an idea of how
much to adjust the temperature.
TO adjust the oven temperature:
1. Press the Bake pad.
2. Enter 550° by pressing the appropriate number pads.
3. Press and hold the Bake pad for several seconds or until 00°appears in the display.
If the oven temperature was previously adjusted, the
change will be displayed. For exampb, if the oven tem-
perature was reduced by 15° the display will show "-15 °'.
4. Press the Autoset pad to adjust the temperature. Each time the Autoset pad is pressed, the temperature
changes by 5°, The oven temperature can be increased or decreased by 5° to 35°,
5. The time of day will automatically reappear in the display.
You do not need to readjust the oven temperature if there is a
power failure or interruption. Temperature adjustment applies to Bake, Convect Bake and Convect Roast (select models)
only.
The Favorite pad allows you to savethe time and temperature from a Cook & Hold Bake, Convect Bake or Convect Roast
(select models) cycle. To set a Favorite cycle, a Cook & Hold function must be either
active or just programmed.
TO set a new Favorite cycle or to save a cur- rently running Cook & Hold as a Favorite:
1. Program a Cook & Hold cycle as described in the Cook & Hold section on page 8.
2. Pressand hold the Favorite pad for three seconds.
° The newly set or currently running Cook & Hold cycle
wiii be saved.
° A beep wiii sound to indicate that the controi has
accepted the Favorite setting.
To start a cycle programmed into Favorite:
1. Pressthe Favorite pad. , Time and temperature for the set Cook & Hold cycle will
be displayed. (If no Cook & Hold cycb has been pro-
grammed, "nonE" is displayed.)
2. Pressthe Bake, Convect Bake or Convect Roast (select models) pad.
, The Favorite cycb will begin immediately. ° The selected cycle icon will light in the display
° The cooking time will light in the display
When the cooking time has elapsed:
° The selected cycle icon will turn off. ° The HOLDWARM icon will light.
, 170°wflHdisplay.
To eaneem a Favorite eyeJe in progress:
1. Pressthe CANCEL pad. ° The stored Favorite cycle wiii not be affected.
2. Removefood from the oven.
12
Oven Light
The Oven Light automatically comes on whenever the oven door is opened. When the door is dosed, press the Oven Light
pad to turn the Oven Light on or off. A beep will sound every
thne the Oven Light pad is pressed.
Oven Racks
* Do not attempt to change the rack position when the oven
is hot.
Oven Vent
The oven vent is Hocatedbdow the controHpand on your wall
oven. When tile oven is hi use, tile area near tile oven vent may
become hot enough to cause bums, Do not block tile vent
opening for best baking results.
Oven Fans
The cooling fan will automatically turn on during cleaning. broiling and some baking operations, it is used to help keep
internal parts on the control panel cool. The fan will automati- cally turn off when parts have cooled. The fan may continue
to operate after the oven has been turned off. This is normal. A convection fan (select models) is used to circulate hot air
in the oven when the convection feature is selected. It automatically turns on whenever a Convect pad is pressed
and will turn off when Convect is canceled.
Note: The convection fan will automatically stop whenever the oven door is opened.
Do not use the oven for storing food or cookware.
Single and Double Convect Ovens - two flat and one offset rack were packaged for each oven.
Single and Double Non-Convect Ovens - one flat and one offset rack were packaged for each oven.
To remove:
1. Pu[[forward to tile "stop" position.
2. Lift up on the front of the rack and pull out.
To replace:
1. Place rack on the rack support in the oven.
2. Tilt the front end up slightly; slide rack back until it clears the lock-stop position.
3. Lower front and slide into the oven.
Rack Positions
Three-rack Convection Baking
(select modeRs)
Rack Position #4:
Three-rack baking Onodds with convection only).
Rack Position #4o (offset rack on #4):
Most broiling.
Rack Position #3:
Most baked goods on a cookie sheet orjelly roll pan.
Rack Position #3o (offset rack on #3):
Most baked goods, pies, layer cakes.
13
4 (fiat reck}
30 (offset reck)
1 (fiat reek)
Rack Position #2:
Roasting small cuts of meat, cakes in tube or bundt pans,
casseroHes.
Rack Position #20 Coffseton #2D:
Roasting, [oaves of bread, angd food cake.
Rack Position #1 :
Large cuts of meat and turkey, custard pie, dessert souffle.
Multiple Rack Cooking:
Two racks: Use #20 and #4= Three racks (convection cooking - sdect moddsD:
Use #1, #30, #4=(See illustration on page 13=_)
The use of the offset rack is denoted in the [ist as an "o" after the rack position number.
When baking on two or three racks, check foods at the
minimum suggested time to avoid over=browning or
over=cooking=
Do not cover an entire rack with aluminum foi[ or pHacefoi[
on the oven bottom. Baking resuHtswill be affected and damage may occur to the oven bottom.
Create-A-Space TMHalf flack
(select models}
Select wall oven models are /_ half rack. The left side of
the rack can be removed to accommodate a large
roaster on the lower rack. The right side of
equipped with a convertible_
the rack is still available to hold a _
casserole dish.
//
, The removable section of the rack can be used as a
roasting rack in the broiling pan. Do not use the top insert when using the rack in the broiling pan.
° The removable section of the rack can be used as a
cooling rack or trivet.
° Make sure oven is cool before removing or reinstalling
the half rack.
, Do not use cookware that extends beyond edge of rack. ° For best results, allow two inches between the pan
placed on the rack and the oven side wall.
° Use caution when removing items from the half rack to
avoid burns.
Carefully remove items from the lower rack to avoid
disturbing the half rack.
14
Seff-C ean Oven
o Jt is norreal for parts of the oven to become hot during a
self-clean cycle.
- To prevent damage to oven door. do not attempt to open the door when LheLOCK icon is displayed.
, Avoid touching door. window or oven vent area during a
dean cycle.
- Do not use commercial oven cleaners on the oven finish or around any pareof the oven. They wiii damage the
finish ol parts.
Theself-clean cycle usesabove-normal cooking temperatures to automatically clean the oven interior.
It is normal for flare-ups, smoking, or flaming to occur during
cleaning if the oven is heavilysoiled. It is better to clean the oven regularly rather than to wait until there isa heavy build-up of soil
in the oven.
During the cleaning process, the kitchen should be well venti-
lated to get rid of normal odors associated with cleaning.
Before Seff-Cmeaning
1. Remove broiler pan, all pans, and oven racks from the oven. The oven racks will discolor and may not slide easily after a
self-clean cycle if they are not removed.
2. Clean oven frame, door frame (area outside of gasket, and around the opening in the door gaske0 with a nonabrasive
cleaner such as Bon Ami* or detergent and water. The self- cleaning process does not clean these areas. Theyshould be
cleaned to prevent soil from baking on during the clean cycle.
{The gasket is the seal around the oven door and window}.
3. To prevent damage, do not clean or
rub the gasket around the oven door.
The gasket is designed to seal in heat during the clean cycle.
4. Wipe up excess grease or spillovers from the oven bottom. This prevents
excessive smoking, flare-ups or fiam-
ing during the clean cycle. To make cleaning easier, the heating dement can be lifted slightly (about 1inch}.
5. Wipe up sugary and acidic spillovers such as sweet potatoes, tomato, or milk-based sauces. Porcelain enamel is acid-
resistant, not acid-proofi The porcelain finish may discolor if
acidic or sugar}, spills are not wiped up before a self-clean cycle.
To set Self-Clean:
Notes:
Oven temperature must be below 400° Fto program a clean cycle.
In double wall oven models, only one oven can be
cleaned at a time.
1. Close the oven door.
2. Press the Clean pad. ° The CLEAN icon flashes.
° "SET" flashes in the display. Autoset
3. Press the Autoset pad. ° "MEd" (Medium Soil, 3 hours} is displayed.
4. Press the Autoset pad to scroll through the self-cleaning settings.
"HW/" (Heavy Soil, 4hours} "MEd" (Medium soil, 3 hours}
"LITE" ( Light Soil, 2 hours} Choosing the soil level of the oven automatically programs
the self-cleaning time.
5. After four seconds, the oven will start cleaning. ° If the door is not closed, beeps will sound and 'door' will
display. If the door is not closed within 30 seconds, the self-cleaning operation will be canceled and the display
will return to the time of day.
° The CLEAN icon will appear in the display. ° The LOCK icon will flash in the display. Once the
door locks, the icon will remain steady.
° The cleaning time will start counting down in the display.
To Delay a Self-Clean Cycle: .......................
1. Press the Delay or Delay 1 pad (select models} ° The DELAY icon flashes. ° 00:00will flash in the display. Delay|
2. Enter the amount of time you want to delay the cycle using the appropriate number pads.
3. Press the Clean pad. ° SETflashes in the display.
4. Press the Autoset pad. ° "LITE" (Light soil level} is displayed.
Autoset
t
*Brand names for cleaning products areregistered trademarks ofthe respective manufacturers.
15
5. PresstheAutosetpadtoscrollthroughthe Autoset stir-cleaningsettings.
"HVy"(HeavySoil4hours} "MEd"(MediumSoii,3hours}
"LITE"(LightSoil2hours} Choosingthesoiibveioftheovenautomaticallyprograms
thesdf-cbaningtime.
6. Afterfourseconds,theCLEANandDELAYiconswillHight andtheLOCKiconwillflashinthedispiay.Whenthe
ovendoorHatches,theLOCKiconwillstopflashingand
Hightcondnuousiytoshowthattheovenissetfora
ddayeddeanoperation.Theddaytimewilldisplay.
During the Seff-CRean Cycle
When LOCK shows in the display, the door cannot be opened, To prevent damage to the door, do not force the door open when LOCK is displayed,
Smoke and Smells
You may see some smoke and smell an odor the first few
times the oven is cleaned. This is normal and will lessen in time.
Smoke may also occur if the oven is heavily soiled or if a broiler pan was left in the oven.
Sounds
As the oven heats, you may hear sounds of metal parts expanding and contracting. This is normal and will not
damage the oven.
After Seff-C eaning
About one hour after the end of the self-dean cycle, the LOCK icon will turn off. The door can then be opened.
Some soil may leave a light gray, powdery ash. Remove it with a damp cloth. If soil remains after wiping, that means
the clean cycb was not long enough. The soil will be re- moved during the next dean cycb.
mfoven racks were left in the oven and do not slide smoothly after a clean cycle, wipe racks and rack supports
with a small amount of vegetaMe oil to make them easier to move.
Fine lines may appear in the porcelain because it went through heating and cooling, This is normal and will not
affect performance. A white discoloration may appear after cleaning if acidic
or sugary foods were not wiped up before the self-clean cycle. This discobration is normal and will not affect perfor-
mance.
If the oven door is left open, "door" wiii flash in the display and a signal will beep until the door is closed
and the Clean pad is pressed again. If more than five seconds elapse between pressing the
Clean pad and the Autoset pad, the program will automatically return to the previous display.
A cooling fan will turn on during the self-clean cycle and
will automatically turn off after the clean cycle when the
oven has cooled. If it does not operate, contact an authorized servicer.
The oven door wiii be damaged if the oven door is
forced to open when the LOCK icon is still displayed.
16
Cleaning Procedures
.To preven[ staining or discoloration, dean appUianceafter each use,
Brand names are registered trademarks of the
respective manufacturers.
*_To order call 1-800-088-9900 USAor
1-800-088-2002 Canada
PART PROCEDURE
Broiler Pan Never cover insert with alum#turn foil as this prevents the fat from draining to the pan below.
and insert ° PHacesoapy cloth over hsert and pan; Hotsoak to Hoosensoft=
, Wash in warm soapywater. Usescouring pad to remove stubborn soil. , Broiler pan and insert can be cleaned in dishwasher.
Control Panel ° To activate "Control Lock" for cleaning, see page 5=
, Wipe with damp cloth. Dr}, thoroughly. , Glass cleaners may be used if sprayed on a cloth first. DO NOTspray directly on eontrolpad and
display area.
, Do not use other cleaning sprays, abrasive cleaners or large amounts of water on the panel. , DO NOT USEANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.
Oven Exterior DO NOT USE ORANGE OR ABRASIVE CLEANERS. (select models_= ° ALWAYS VJIPE WITH THE GRAIN WHEN CLEANING.
Stainless Steel ° Daily Cleaning/Light soil -= Wipe with one of the foflowing - soapy water, white vinegar/water
solution, Formula 409Glassand Surface Cleaner*or a similar glass cleaner - using asponge orsoft cloth.
Rinse and dry=To polish and help prevent fingerprints, follow with Stainless SteelMagic Spray (Part No=20000008:}_=
° Moderate/Heavy Soil -- Wipe with one of thefollowing - Bon Ami_,Smart Cleanser_,or Soft Scrub* -
using a damp sponge or soft cloth. Rinse and dry=Stubborn soils may be removed with a damp Scotch-
Brite* pad; rub evenly with the grain. Rinse and dry=To restore luster and remove streaks, follow with
Stainless Steel Magic Spray.
Oven Window & ° Avoid using excessive amounts of water which mayseep under or behind glass causing staining. Door - Glass , Wash with soap and water. Rinsewith clear water and dry= Glass cleaner can be used if sprayed on a
cloth first.
° Do not use abrasive materials such as scouring pads, steel wool or powdered cleaners as they will
scratch glass.
Oven Trim = , Wash with soap and water, glasscleaners or mild liquid sprays. Avoid using excessive amounts of water. Metal Finishes , Removestubborn soils with nonabrasive cleaners such as Bon Ami _or a baking soda and water paste;
rinse and dry'.Do not use abrasive cleaners.
Oven interior , See page 15for information on the self-clean oven.
, To remove occasional spfllovers between deanings, use a plastic soap-filled scouring pad; rinsewell. , Wipe up sugary spfllovers and acidic spfllovers such as lemon juice, tomato sauce or milk-based sauces.
Porcelain enamel isacid resistant, not acid proof. The porcelain finish maydiscolor ifacidic or sugary spills
are not wiped up prior to a self-clean cycle.
Oven Racks , Rubwith a sponge or cloth using one of the following cleaners: Bon-Ami*, Soft Scrub* or Comet_-Rinse
and dry,.
° For hard to remove softs,use a dampened soap-filled scouring pad. Rinse and dry. ° Racks will permanently discolor and may not slide smoothly if left in the oven during a self-clean
operation. If this occurs, wipe the rack and embossed rack supports with a small amount of vegetable oil to restore ease of movement, then wipe off excess oil
17
Oven Light
, Before repUacinglight bulb, DISCONNECT POWERTO OVEN.
Be sure buUbis CooU.'
may break.
To replace oven light:
1. Use a dry pothoHderand very carefully unscrew buHbcover and buHb=
2. RepHacewith a 40 watt, oven-rated appHiancebuHb.BuHb with a brass base is recommended to prevent fusing of
buHbinto socket.
3. RepHacebuHbcover and reconnect power to oven.
4. Reset chock,
Oven Window
To protect the oven door window:
1. Do not use abrasive cleaning agents such as steal wooH scouring pads or powdered cleansers as they may scratch
the gHass.
2. Do not hit the gHasswith pots, pans, furniture, toys, or other objects.
3. Do not chosethe oven door untiHthe oven racks are in
pHace.
Scratching, hitting, jarring or stressing the glass may weaken its structure causing an increased risk of breakage at a later
date.
18
PROBLEM SOLUTION
For most concerns, try these first.
CJock, indicator words, andlor Jightsoperate but oven does
not heat.
Oven light andlor clock does not function.
There is a strong odor or light smoke when oven isturned on.
Oven wiii not activate the
, Check if oven controls have been properly set. , Check if oven is properly connected to electrical outlet. , Check or re-set circuit breaker. Check or replace fuse.
, Check power supply.
, Oven may be set for a Cook & Hold or Delay function. , The Oven Control Lockout may have been set. (Seepage 5._)
, The light bulb is loose or defective. , The oven light does not work during self-cleaning process.
, Oven may be in Sabbath Mode. (See page 11=)
, This is normal for a newwall oven and will disappear after afew uses.Initiating a clean
cycle will "burn off" the smells more quickly. Turning on a ventilation fan will help remove the smoke and/or odor.
, Excessivefood soils on the oven bottom. Use a self-clean cycle.
, Oven may be set for a delay clean. ° Oven may be in Sabbath Mode. [See page 11.)
° Oven may be over 400° F.Oven temperature must be below 400° Fto program a
clean cycle.
Oven did not dean properly.
Foods do not broil properly.
Baked food is burned or too brown on top.
Foods bake unevenly.
Oven door will not unlock.
, Oven may need longer cleaning time. , Excessive spills were not removed prior to self-cleaning process.
° Check rack position. (See page 9.) , Voltage into house may be low.
° Foodmay be positioned incorrectly inoven. (See"Cookin_3MadeSimple"booklet.) ° Oven not preheated properly.
° Oven was not preheated. ° The oven may be installed improperly.
° Check the oven rack with a level. ° Stagger pans, do not allow pans to touch each other or oven wall.
° Check instructions for suggested placement of pans on oven rack. (See "CoeA'ing
Made Simple" booklet.)
, Oven may not have cooled to safe temperature after self-cleaning process. ° The control and door may be locked. (See page 5.)
19
PROBLEM SOLUTION
Oven baking results are less ° The pans behg used may net be ofthe size or materiaHrecommended for best than expected, resuHts.(See "Cookii_g Made Simple" booHeLD
" There may not be sufficient room around sides of the pans for proper air circuHation
in the oven.
, Check instructions for preheating, rack position and oven temperature.
Baking results differ from , Oven thermostat calibration may differ between old and new ovens. Follow recipe previous oven. and usethe directions in this guide before calling for service since the calibration on
the previous oven may have drifted to a too high or too low setting. (See page 12 - Adjusting the Oven Temperature.:)
Fan is heard during broiling, , This is the cooling fan and is normal. The fan will continue to run after use cleaning and some baking until the oven cools.
operations.
Cooling fan continues to , This is normal. The fan will automatically shut off when the oven is cooled. operate after the oven has been
turned off.
Fault Codes , The BAKEor LOCK icon may flash rapidly inthe display to alert you if there isan error
or a problem. If the BAKEor LOCKicon appears in the display, press CANCEL pad.
If the BAKE or LOCK icon continues to flash, disconnect power to the appliance.
Wait a few minutes, and then reconnect power. If the icon flashing still continues, disconnect power to the appliance and call an authorized servicer.
, If the oven is heavily soiled, excessive fiareups may result in a fault code during
cleaning. Press the CANCEL pad and allow the oven to cool completely, wipe out excess soil, then reset the clean cycle. If the fault code reappears, contact an
authorized servicer.
There are no beeps and , Oven may be in Sabbath Mode. (See page 11.) no display.
Noises may be heard. , The oven makes several low level noises. You may hear the oven cooling fan going
on and off. You may also hear the oven relays as they go on and off. These are all normal.
, As the oven heats and cools, you may hear sounds of metal parts expanding and
contracting. This is normal and will not damage your appliance.
2O
Loading...
+ 47 hidden pages