Maytag MER7685B, MER7662W, MER7664X User Manual

30" (76.2 cm) Freestanding Electric Range

A

B

D

F

E

C

PRODUCT MODEL NUMBERS

MER7662W
MER7664X
MER7685B
MER8600D
MER8650E

Electrical: To properly install your range, you must determine the type
of electrical connection you will be using and follow the instructions
provided for it here.

• Range must be connected to the proper electrical voltage
and frequency as specified on the model/serial number rating plate.
The model/serial number rating plate is located on the left side frame
behind the storage drawer panel or behnd the top right side
of the oven door. Refer to the figures in the “Product Dimensions”
section of the “Location Requirements” section.

• This range is manufactured with the neutral terminal connected
to the cabinet. Use a 3-wire, UL listed. 40- or 50-amp power supply
cord (pigtail) (see following Range Rating chart). If local codes
do not permit ground through the neutral, use a 4-wire power supply
cord rated at 250 volts, 40 or 50 amps and investigated
for use with ranges.

Range Rating*

120/240 Volts 120/208 Volts Amps

8.8 – 16.5 KW 7.8 – 12.5 KW 40 or 50 **

16.6 – 22.5 KW 12.6 – 18.5 KW 50

* The NEC calculated load is less than the total connected load listed

on the model/serial rating plate.

** If connecting to a 50-amp circuit, use a 50-amp rated cord with a kit.

For 50-amp rated cord kits, use kits that specify use with a nominal

3

1

/8" (34.9 mm) diameter connection opening.

• A circuit breaker is recommended.

MER8670A
MER8674A
MER8680B
MER8700D
MER8775A

MER8800D
MER8850D
MER8880A
MER8885A
MIR8890A

Specified Rating of
Power Supply Cord Kit
and Circuit Protection

CABINET OPENING DIMENSIONS

Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and 36"
(91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood
combination above the range, following the range hood or microwave
hoods combination instructions for dimensional clearances
above the cooktop surface.

A freestanding range may be installed next to combustible walls
with zero clearance.

* NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet

is covered by not less than 1/4" (0.64 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm)
stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.

PRODUCT DIMENSIONS

A

F

E

D

A. 273/4" (70.5 cm) max. depth with handle
B. 467/8" (119.1 cm) overall height (max.) with leveling legs

screwed all the way in*

C. 36" (91.4 cm) cooktop height (max.) with leveling legs

screwed all the way in*
D. 297/8" (75.9 cm) width
E. 255/16" (64.3 cm) depth – back of range to front of cooktop**
F. Model/serial rating plate (located on the left side frame behind

storage drawer or right side of frame behind the oven door)

IMPORTANT: Range must be level after installation. Follow
the instructions in the “Level Range” section. Using the cooktop
as a reference for leveling the range is not recommended.

* Range can be raised approximately 1" (2.5 cm)

by adjusting the leveling legs.

** Front of door and drawer may extend further forward

depending on styling.

A. 13" (33.0 cm) max.

upper cabinet depth

B. 30" (76.2 cm) min.

opening width

C. For minimum clearance

to top of cooktop,
see NOTE*

D. 301/8" (76.5 cm) min

opening width

E. Outlet – 8" (20.3 cm)

to 22" (55.9 cm) from either
cabinet, 51/2"
(14.0 cm) max. to floor

F. Cabinet door or hinges

should not extend
into the cutout

C

B

Because Whirlpool Corporation includes a continues commitment to improve
our products, we reserve the right to change materials and specifications
without notice.

Dimensions are for planning purposes only. For complete details,
see Installation Instructions packed with product. Specifications
subject to change without notice.

Ref. W10403811C

03/15