Maytag MEDB850WR0, MEDB850WQ0, MEDB850WL0, MEDB850WB0, MEDB800VU0 Owner’s Manual

...

BRAVOS ®STEAM FABRIC CARE

SYSTEM ELECTRIC DRYER

USE & CARE GUIDE

p p

SECHEUSE ELECTRIQUE BRAVOS ®

AVEC SYSTEME

DE SOIN DES TISSUS A LA VAPEUR

GUIDE D'UTILISATION ET D'ENTRETIEN

FOR QUESTIONS ABOUT FE,a(IURES, OPERATION/PERFORMANCE, PARTS, ACCESSORIES OR SERVICE

CAll: 1.800.688.9900

IN CANADA, CAll: 1.800.807.6777

VISIT OUR WEBSITE AT WWW.MAYTAG.COM

IN CANADA, WWW.MAYTAG.CA

W10201176B

AU CANADA, POUR ASSISTANCE, INSTAllATION OU SERVICE, COMPOSEZ IE : 1.800.807.6777

OU VISITEZ NOTRE SITE INTERNET ,_

WWW. M AYTAG. CA

,i_!_ii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i_i_i_ii!i¸i!i!i!i!i!i!i!i_i_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_i_iiiiYiiiiii//li¸il¸iiii_ii,i_ii,i_ii,i_ii,i_ii,i_i_iii_i_ii_il'ii_i_iil'ii_i_iil_i_ii_i_ii_i_ii_ii_i_ii_:ii:_:i_:ii:_:i_:ii:_:i_:ii:_:i_:ii:_:i_:ii:_:i_:ii:_:i_:_i_::¸ _:iii!ii,l,ii_,,¸¸¸¸_!_iiiiiiiii_i_ ¸il¸ii_ii_ii¸I¸I¸il¸ii_ii¸ii_ii¸ii_ii¸ii_iil¸ii_i_iil¸I¸iiiii_iiiii_i_i_ii_i_iiiii_ii_iii_ii_iii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_!_!!

TABLE OF CONTENTS

DRYER SAFETY .......................................................................................................................... 3

INSTALLATION INSTRUCTIONS ............................................................................................. 4

Tools and Parts ....................................................................................................................... 4

I.ocation Requirements .......................................................................................................... 5

Electrical Requirements - U.S.A. Only .................................................................................... 6

Electrical Requirements - Canada Only .................................................................................. 8

Electrical Connection - U.S.A. Only ....................................................................................... 9

Venting Requirements .......................................................................................................... 15

Plan Vent System .................................................................................................................. 17

Install Vent System ............................................................................................................... 18

Install I_eveling I.egs ............................................................................................................. 18

Connect Vent ....................................................................................................................... 19

Connect Inlet Hose ............................................................................................................... 19

I.eve[ Dryer .......................................................................................................................... 20

Reverse Door Swing ............................................................................................................. 20

Complete Installation .............................................................................................................

DRYER USE.............................................................................................................................. 23

Starting Your Dryer ............................................................................................................... 23

Stopping, Pausing, or Restarting ........................................................................................... 24

Drying and Cycle Tips .......................................................................................................... 24

Status I_ights .......................................................................................................................... 25

Cycles .................................................................................................................................. 25

Modifiers .............................................................................................................................. 27

Options ................................................................................................................................ 27

End Signal ............................................................................................................................ 28

Changing Cycles, Modifiers, and Options ............................................................................ 28

Drying Rack Option ............................................................................................................. 28

DRYER CARE ........................................................................................................................... 29

Cleaning the Dryer I.ocation ................................................................................................ 29

Cleaning the I_int Screen ...................................................................................................... 29

Cleaning the Dryer Interior ................................................................................................... 30

Removing Accumulated I.int ................................................................................................ 30

Water Inlet Hoses ................................................................................................................. 30

Vacation, Storage and Moving Care ..................................................................................... 30

Changing the Drum Light ..................................................................................................... 31

TROUBLESHOOTING ............................................................................................................. 31

Dryer Operation ................................................................................................................... 31

Dryer Results ..........................................................................................................................

ASSISTANCE OR SERVICE ....................................................................................................... 34

In the U.S.A .......................................................................................................................... 34

In Canada ............................................................................................................................. 34

ACCESSORIES ......................................................................................................................... 34

WARRANTY ............................................................................................................................ 35

TABLE DES MATIERES

SI_CURITI_ DE LA SI_CHEUSE ................................................................................................... 36

INSTRUCTIONS D'INSTALLATION ....................................................................................... 38

Outillage et pi_ces ............................................................................................................... 38

Exigences d'emp[acement .................................................................................................... 38

Spdcifications 6lectriques - Pour le Canada seulement ......................................................... 39

Exigences concernant ['6vacuation ...................................................................................... 40

Planification du syst&me d'6vacuation ................................................................................. 42

Installation du syst&me d'6vacuation .................................................................................... 43

Installation des pieds de nivellement .................................................................................... 44

Raccordement du conduit d'6vacuation ............................................................................... 44

Raccordement des tuyaux d'a[imentation ............................................................................ 44

R6g[age de ['aplomb de [a s6cheuse ..................................................................................... 45

Inversion du sens d'ouverture de [a porte ............................................................................. 45

Achever ['installation ............................................................................................................ 47

UTILISATION DE LA SI_CHEUSE ............................................................................................. 48

Mise en marche de [a s6cheuse ............................................................................................ 48

Arr&t, pause ou remise en marche ........................................................................................ 50

Conseils pour [e s6chage et [es programmes ........................................................................ 50

T6moins [umineux ................................................................................................................ 50

Programmes ......................................................................................................................... 51

Modificateurs ....................................................................................................................... 52

Options ................................................................................................................................ 53

End Signal (signal de fin de programme) .............................................................................. 53

Changement des programmes, modificateurs, et options ..................................................... 53

Option de grille de sdchage ................................................................................................. 54

ENTRETIEN DE LA SI_CHEUSE ................................................................................................ 55

Nettoyage de ['emplacement de [a s6cheuse ........................................................................ 55

Nettoyage du filtre b_charpie ................................................................................................ 55

Nettoyage de ['int6rieur de [a s6cheuse ................................................................................ 56

Retrait de [a charpie accumul6e ........................................................................................... 56

Tuyaux d'arriv6e d'eau ......................................................................................................... 56

Pr6cautions b_prendre avant [es vacances, un entreposage ou un d6mdnagement ............... 56

Changement de ['ampoule d'6clairage

du tambour. .......................................................................................................................... 57

DI_PANNAGE .......................................................................................................................... 58

Fonctionnement de [a s6cheuse ........................................................................................... 58

R6sultats de [a s6cheuse ....................................................................................................... 59

ASSISTANCE OU SERVICE ...................................................................................................... 61

Au Canada ........................................................................................................................... 61

ACCESSOIRES .......................................................................................................................... 61

Notes .................................................................................................................................... 62

GARANTIE ............................................................................................................................... 63

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't i_ follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING - "RiskofFire"

- Clothes dryer installation must be performed by a qualified installer,

- install the clothes dryer according to the manufacturer's instructions and local codes,

- Do not install a clothes dryer with flexible plastic venting materials, if flexible metal {foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers, Flexible venting materials are

known to collapse, be easily crushed, and trap lint, These conditions will obstruct clothes dryer airflow and increase the risk of fire,

- To reduce the risk of severe injury or death, follow all installation instructions,

- Save these instructions,

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

Read all instructions before using the dryer. Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

• Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

• Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is

used near children.

• Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

• Do not reach into the dryer if the drum is moving.

• Do not install or store the dryer where it will be exposed to the weather.

• Do not tamper with controls.

SAVE THESE INSTRUCTIONS

• Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to

carry out.

• Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric

softener or product.

• Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

• Clean lint screen before or after each load.

• Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

• The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.

• See installation instructions for grounding requirements.

Gather the required tools and parts before starting installation. Read and follow the

instructions provided with any tools listed here.

• Flat-blade screwdriver • Tin snips (new vent installations)

• #2 Phillips screwdriver • I.evel Adjustable wrench that opens to 1"

(25 mm) or hex-head socket wrench (for adjusting dryer feet)

• Wire stripper (direct wire installations)

• Vent clamps

• Caulking gun and compound (for installing new exhaust vent)

• Tape measure

Parts supplied:

Remove parts package from dryer drum. Check that all parts were included.

B D E

A. Levering legs (4)

B. "Y" connector C. Short inlet hose

D. Inlet hose with right-angle connector

E. Rubber washer

Parts needed:

Check local codes. Check existing electrical supply and venting and see "Electrical

Requirements" and "Venting Requirements" before purchasing parts. Mobile home installations require metal exhaust system hardware available for purchase from

the dealer from whom you purchased your dryer. For information on ordering, please refer to the "Assistance or Service" section. You may also contact the dealer from whom you

purchased your dryer. If using a power supply cord:

Use a UI. listed power supply cord kit marked for use with clothes dryers. The kit should contain:

• A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at [east 4 ft (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or spade terminals with upturned ends.

• A UI. listed strain relief.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at [east 18 inches (460 ram) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. See "Venting Requirements."

• A separate 30-amp circuit.

• If you are using a power supply cord, a grounded electrical outlet located within 2 ft (610 mm) of either side of the dryer. See "Electrical Requirements."

• A sturdy floor to support the total weight (dryer and load) of 200 Ibs (90.7 kg). The

combined weight of a companion appliance should also be considered.

• Cold water faucets located within 4 ft (1.2 m) of the water fill valves, and water pressure of 20-100 psi (138-690 kPa). You may use the water supply for your washer using the "Y"

connector and short hose (if needed) which are provided.

• 20-100 psi (138-690 kPa) for best performance.

• A level floor with a maximum slope of 1" (25 mm) under entire dryer.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Dryer Dimensions

*Most installations require a minimum 5" (127 mm) clearance behind the dryer for the

exhaust vent with elbow. See "Venting Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0" (0 mm) clearance on the sides and rear. Recommended spacing should be

considered for the following reasons:

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances might be required for wall, door and floor moldings.

• Additional spacing should be considered on all sides of the dryer to reduce noise transfer.

• For closet installation, with a doo_; minimum ventilation openings in the top and bottom of the door are required. I.ouvered doors with equivalent ventilation openings are

acceptable.

• Companion appliance spacing should also be considered.

Additional spacing is required if you exhaust out the rear of the dryer to either the right or left side.

___ 3I1.

tJall 14" ma__

I_ Il;._mm)

_in}*_

(3100m_

g6mm)

24in.2*

1"_ I_- _"_ _1" _11"*1_29,/4"Hs"

mm) 125ram)

(737ram)

(25ram) {743ram) (127ram)

A. Recessed area B. Side view - closet or confined area

C. Closet door with vents

(i_m_"

[Z6mm)

*Required spacing

Mobile home - Additional installation requirements This dryer is suitable for mobile home installations. The installation must conform to the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the

Federal Standard for Mobile Home Construction and Safety, Title 24, HUll Part 280) or

Standard CAN/CSA-Z240 MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for purchase from your dealer.

• Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at [east twice as large as the dryer

exhaust opening.

It is your responsibility

• To contact a qualified electrical installer.

• To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and

ordinances. The National Electric Code requires a 4-wire power supply connection for homes built

after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical

supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate)

on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in

the neutral or grounding circuit.

• I)o not use an extension cord.

• If codes permit and a separate ground wire is used, it is recommended that a qualified

electrician determine that the ground path is adequate.

Electrical Connection

To properly install your dryer; you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

• This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground conductor is permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the

neutral ground conductor must be removed from the external ground connector (green screw), and secured under the neutral terminal (center or white wire) of the terminal

block. When the neutral ground conductor is secured under the neutral terminal (center

or white wire) of the terminal block, the dryer cabinet is isolated from the neutral

conductor. If local codes do not permit the connection of a neutral ground wire to the neutral wire,

see "Optional 3-wire connection" in "Electrical Connection - U.S.A. Only" section. A 4-wire power supply connection must be used when the appliance is installed in a

location where grounding through the neutral conductor is prohibited. Grounding

through the neutral is prohibited for (1) new branch-circuit installations, (2) mobile

homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding

through the neutral conductors.

If using a power supply cord: Use a UI. listed power supply cord kit marked for use with clothes dryers. The kit should

contain:

• A UI_ listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be

type SRI) or SRI)T and be at least 4 ft (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or spade terminals with upturned ends.

• A UL listed strain relief.

If your outlet looks like this:

4-wire receptac/e (14-30R)

Then choose a 4-wire power supply cord with ring or spade terminals and UI_ listed strain

relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green or bare. The neutral conductor must be identified by a white

cover. If your outlet looks like this:

3-wire receptacle (lO-30R)

Then choose a 3-wire power supply cord with ring or spade terminals and UI. listed strain

relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire: Power supply cable must match power supply (4-wire or 3-wire) and be:

• Flexible armored cable or nonmetallic sheathed copper cable (with ground wire), protected with flexible metallic conduit. All current-carrying wires must be insulated.

• 10-gauge solid copper wire (do not use aluminum).

• At [east 5 ff (1.52 m) long.

GROUNDING INSTRUCTIONS

I For a grounded, cord-connected dryer: This dryer must be grounded, in the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current. This dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and grounded in accordance with all local codes and

ordinances. m For a permanently connected dryer:

This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on the dryer.

WARNING-" Improper connection of the equipment- grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug on the power supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Electrical Shock Hazard

Plug into a grounded 4 prong ouUet. Failure to do so can result in death or electrical shock.

It is your responsibility

• To contact a qualified electrical installer.

To be sure that the electrical connection is adequate and in conformance with the Canadian Electrical Code, C22.1 -latest edition and a[[ local codes. A copy of the above

codes standard may be obtained from: Canadian Standards Association, 178 Rexda[e Blvd., Toronto, ON M9W 1R3 CANADA.

To supply the required 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical

supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit.

This dryer is equipped with a CSA International Certified Power Cord intended to be

plugged into a standard 14-30R wail receptacle. The cord is 5 ft (1.52 m) in length. Be sure wail receptacle is within reach of dryer's final location.

If you are using a replacement power supply cord, it is recommended that you use Power

Supply Cord Replacement Part Number 3394208. For further information, please reference the service numbers located in the "Assistance or Service" section.

GROUNDING iNSTRUCTiONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local

codes and ordinances. WARNING-" Improper connection of the

equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to

whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE iNSTRUCTIONS

• Do not use an extension cord.

4-wire receptacle 14-30R

I!!,°,,<..°(.=,isl ¢;cA O ly

Power Supply Cord

Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief.

Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (silver). Ground wire (green or bare wire) must be connected to

green ground connector. Connect remaining 2 supply wires to remaining

2 terminals (gold). Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

Fire Hazard

Direct Wire

Fire Hazard

Use 10 gauge sold copper wire. Use a UL listed strain relief.

Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (silver). Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 supply wires to remaining 2 terminals (gold}.

Securely tighten all electrical connections. Failure to do so can result in death, fire, or

electrical shock.

2. Remove the hold-down screw and terminal block cover.

AB C D

3. Install strain relief.

A. Terminal block cover

B. HoM-down screw location C. fxternal ground conductor

screw

D. Centel, si/ver-colored

terminal block screw

E. Neutral ground wire £ Hole below terminal block

opening

Style 1: Power supply cord strain relief1. Disconnect power.

Remove the screws from a s/4" (19 mm) UI_ listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections into the hole below the terminal block opening so

that one tab is pointing up and the other is pointing down, and hold in place. Tighten

strain relief screws just enough to hold the two damp sections together.

; ....; i ................A

A. Strain refief tab pointing up

B. Hole below terminal block opening

C. Clamp section

D. Strain relief tab pointing down

Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with

the dryer cabinet and be in a horizontal position. Do not further tighten strain relief

screws at this point.

• Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the

direct wire cable.

Style 2: Direct wire strain relief Unscrew the removable conduit connector and any screws from a %" (19 mm) UI. listed

strain relief (UI_ marking on strain relief). Put the threaded section of the strain relief through the hole below the terminal block opening. Reaching inside the terminal block opening, screw the removable conduit connector onto the strain relief threads.

............................. C

A. Removable conduit connector

B. Hole below terminal block opening C. Strain relief threads

4. Now complete installation following instructions for your type of electrical connection: 4-wire (recommended)

3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has: And you will be Go to Section:

connecting to:

4-wire receptacle (NEMA type 14-30R)

A UL listed, 120/240-volt minimum,

30-amp, dryer power

4-wire connection: Power Supply Cord

supply cord*

4-wire direct

(127 ram)

3-wire receptacle (NEMA type 10-30R)

A fused disconnect or circuit breaker box*

A UL listed, 120/240-volt minimum,

30-amp, dryer power

4-wire connection: I)irect Wire

3-wire connection: Power Supply Cord

supply cord*

3-wire direct

A fused disconnect or circuit breaker box*

3-wire connection: I)irect Wire

*If local codes do not permit the connection of a cabinet-ground conductor to the neutral

wire, go to "Optional 3-wire connection" section.

| 0

3. Connect ground wire (green or bare) of power supply cord to external ground conductor

4-wire connection: Power supply cord screw. Tighten screw.

IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do

not permit the use of 3-wire connections.

A _ B

C D E G

A. 4-wire receptacle (NEMA type 14-30R)

B. 4-prong plug C. Ground prong

D. Neutral prong

E.Spade terminals with upturned ends I] V4" ( 19 ram) UL listed strain relief

C. Ring terminals

Remove center silver-colored terminal block screw.

1°

Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and the neutral wire (white or center wire) of power supply cord under

center, silver-colored terminal block screw. Tighten screw.

4. Connect the other wires to outer terminal block screws. Tighten screws.

A. fxtemal ground conductor screw

B. Neutral ground wire

C. Cround wire (green or bare) of power supply cord

D. Y4" ( 19 ram) UL fisted strain refief

E. Center silver-colored terminal bkJck screw I] Neutral wire (white or center wire)

A. Neutral ground wire

B. fxtema/ ground conductor screw - Dotted fine shows position

of NLUTRAL ground wire before being moved to center silver- colored terminal block screw.

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. Y4" ( 19 ram) UL fisted strain refief

I I

5. Tighten strain relief screws.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold- down screw.

7. You have completed your electrical connection. Now go to "Venting Requirements."

4-wire connection: Direct Wire

IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3 wire connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.

Strip 5" (127 mm) of outer covering from end of cable, leaving bare ground wire at 5" (127 mm). Cut 1V2"(38 mm) from 3 remaining wires. Strip insulation back 1" (25 mm). Shape ends of wires into a hook shape.

(127 r_

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as

shown.

Remove center silver-colored terminal block screw.

1°

Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and place the hooked end (hook facing right) of the neutral wire (white or

center wire) of direct wire cable under the center screw of the terminal [)lock. Squeeze hooked ends together. Tighten screw.

B.....................................................................................

.................................

A. Neutral ground wire

B. External ground conductor screw - Dotted fine shows

position of Nf_UTRAL ground wire before being moved to center silver-colored terminal block screw.

C. Center silver-colored terminal block screw D. Neutral wire (white or center wire)

E. Y4" ( 19 ram) UL listed strain relief

3°

Connect ground wire (green or bare) of direct wire cable to external ground conductor

screw. Tighten screw.

3-wire connection: Power supply cord

A. External ground conductor screw

B. Neutral ground wire

C. Cround wire (green or bare) of power supply cord

D. _/4" ( 19 ram) UL fisted strain refief

E. Center silver-co/ored terminal block screw

£ Neutral wire (white or center wire)

Place the hooked ends of the other direct wire cable wires under the outer terminal block

4°

screws (hooks facing right). Squeeze hooked ends together. Tighten screws.

Use where local codes

)ermit connecting cabinet-ground conductor to neutral wire.

A. 3-wire receptacle (NEMA type lO-30R)

B. 3-wire p/ug C. Neutral prong

D. Spade termina/s with upturned ends

E. V4" ( 19 ram) UL /isted strain relief

£ Ring termina/s

C. Neutra/ wire (white or center wire)

G F

1. I.oosen or remove center silver-colored terminal block screw.

2. Connect neutral wire (white or center wire) of power supply cord to the center, silver- colored terminal screw of the terminal block. Tighten screw.

!! !I

5. Tighten strain relief screw.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold- down screw.

7. You have completed your electrical connection. Now go to "Venting Requirements."

A. External ground conductor screw

B. Neutral ground wire C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. 3/4" ( 19 ram) UL fisted strain refief

Connect the other wires to outer terminal block screws. Tighten screws.

! !!

Tighten strain relief screws.

Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold- down screw.

6°

You have completed your electrical connection. Now go to "Venting Requirements."

3-wire connection: Direct Wire

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.

Strip 31/2'' (89 mm) of outer covering from end of cable. Strip insulation back 1" (25 mm). If

using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of

wires into a hook shape.

Place the hooked end of the neutral wire (white or center wire) of direct wire cable under

the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw.

-m

..............

.................2................

A. External ground conductor screw

B. Neutral ground wire

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. 3/4" (19 ram) UL listed strain relief

Place the hooked ends of the other direct wire cable wires under the outer terminal block

screws (hooks facing right). Squeeze hooked ends together. Tighten screws.

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as

shown.

1. I.oosen or remove center silver-colored terminal block screw.

!! !!

4. Tighten strain relief screw.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold- down screw.

6. You have completed your electrical connection. Now go to "Venting Requirements."

Optional 3-wire connection

Use for direct wire or power supply cord where local codes do not permit connecting

cabinet-ground conductor to neutral wire.

1. Remove center silver-colored terminal block screw.

2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord/cable under

center, silver-colored terminal block screw. Tighten screw.

Fire Hazard

Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic,

crawlspace, or a concealed space of a building.

A. External ground conductor screw

B. Neutral ground wire

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. 3/4" ( !9 ram) UL fisted strain refief £ Crounding path determined by a quafified electrician

Connect the other wires to outer terminal block screws. Tighten screws.

!I !!

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-

down screw.

Connect a separate copper ground wire from the external ground conductor screw to an

adequate ground.

If using an existing vent system

• Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint.

• Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

• Review Vent system chart. Modify existing vent system if necessary to achieve the best

drying performance. Only rigid or flexible metal duct shall be used for exhausting.

If this is a new vent system

Vent material

• Use a heavy metal vent. I)o not use plastic or metal foil vent.

• 4" (1 02 mm) heavy metal exhaust vent and clamps must be used.

4" ( 102 ram) heavy metal exhaust vent

Vent products can be purchased from your dealer or by calling Maytag Services. For more information, see the "Assistance or Service" section.

Rigid metal vent

• For best drying performance, rigid metal vents are recommended.

• Rigid metal vent is recommended to avoid crushing and kinking. Flexible metal vent

• Flexible metal vents are acceptable only if accessible for cleaning.

• Flexible metal vent must be fully extended and supported when the dryer is in its final

location.

• Remove excess flexible metal vent to avoid sagging and kinking that may result in

reduced airflow and poor performance.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

• The total length of flexible metal vent should not exceed 73/4 ft (2.4 m). Elbows

45 ° elbows provide better airflow than 90 ° elbows.

Good Better

Clamps

Use clamps to seal all joints.

The exhaust duct shall not be assembled with screws or other fastening means that extend

into the duct and catch [int. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

_4,_ (1J4_m)

(102 ram)

A. Louvered hood style

B.Box hood style

The angled hood style (shown here) is acceptable.

4 n

(102 mm)_'__

• An exhaust hood should cap the vent to keep rodents and insects from entering the home.

• Exhaust hood must be at least 12" (305 mm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

• I)o not use an exhaust hood with a magnetic latch.

improper venting can cause moisture and lint to collect indoors, which may result in:

m Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

m Housecleaning problems and health problems.

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer.

This dryer can also be exhausted from the rear to either the right or left side. Optional kits for these exhaust installations are needed. Refer to the manufacturer's instructions for kit

installation instructions.

-i- _¸ ]

A ............................

A. Dryer

B.Elbow

C. Waft

D. fxhaust hood

Optional exhaust installations

Venting systems come in many varieties. Select the type best for your installation.

Cover unused exhaust hole with the following kit: 8212503

Contact your local dealer. Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

This dryer can be converted to exhaust out the bottom. If you prefer; you may contact your

local dealer to have the dryer converted.

E.Clamps £ Rigid metal or flexible metal vent

C. Vent length necessary to connect elbows

H. Exhaust outlet

Fire Hazard

A. Standard rear offset exhaust instaflation

B. Rear exhaust instaflation to the right or left side

C D

c. Bottom exhaust installation

D. Over-the-top insta//ation (also avai/ab/e with

one offset eTbow)

NOTE: The following kits for close clearance alternate installations are available for purchase. Please see the "Assistance or Service" section to order.

• Over-the-Top Installation: Part Number 4396028

• Periscope Installation (For use with dryer vent to wail vent mismatch): Part Number 4396037 - 0" (0 mm) to 18" (457.2 mm) mismatch Part Number 4396011 - 18" (457.2 mm) to 29" (736.6 mm) mismatch Part Number 4396014 - 29" (736.6 mm) to 50" (1270 mm) mismatch

• Rear exhaust installation to [eft or right side: Part Number 4396011

• Vent extension: Part Number 8544761

• Bottom Exhaust: Part Number 8212503

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent

outside.

Determine vent path

• Select the route that will provide the straightest and most direct path outdoors.

• Plan the installation to use the fewest number of elbows and turns.

• When using elbows or making turns, allow as much room as possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90° turns possible.

Determine vent length and elbows needed for best drying performance

Number of Type of Box or Angled

90 ° turns vent Louvered hoods or elbows hoods

Rigid metal 80 ft (24.4 m) 74 ft (22.6 m)

3 Rigid metal 71 ft (21.6 m) 65 ft (19.8 m)

4 Rigid metal 63 ft (19.2 m) 57 ft (1 7.4 m)

Install exhaust hood. Use caulking compound to seal exterior wall opening around

exhaust hood.

Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust

hood with 4" (102 mm) clamp.

Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in "Plan Vent System." Avoid 90 ° turns. Use clamps to seal all joints. Do not use duct tape, screws, or other fastening devices that extend into the interior of the vent to secure vent. Items sticking through the vent can catch lint.

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

• Use the following Vent system chart to determine type of vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and increased energy usage.

The Vent system chart provides venting requirements that will help to achieve the best drying performance.

Vent system chart

NOTE: Performance of rear exhaust to either side of the dryer is equivalent to adding one

elbow. To determine maximum exhaust length, add one elbow to the chart.

NOTE: Bottom exhaust performance is equivalent to adding two elbows. To determine maximum exhaust length, add one elbow to the chart.

Number of Type of Box or Angled

90 ° turns vent Louvered hoods or elbows hoods

0 Rigid metal 100 ft (30.5 m) 94 ft (28.7 m)

1 Rigid metal 90 ft (27.4 m) 84 ft (25.6 m)

1. To protect the floor, use a large, flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.

2. Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on the cardboard. See illustration.

Examine the leveling legs. Find the diamond marking.

Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer visible.

5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.

I.eave enough room to connect the exhaust vent.

1. Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. Ifconnecting to

existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust

outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a

4" (102 mm) clamp.

2. Move dryer into its final location. I)o not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible gas line.

4. Once the exhaust vent connection is made, remove the corner posts and cardboard.

The dryer must be connected to the cold water faucet using the new inlet hoses. I)o not use old hoses.

1. Turn cold water faucet off and remove washer inlet hose.

Remove old rubber washer from inlet hose and replace with new rubber washer provided. If space permits, attach the brass female end of the "Y" connector to the cold water faucet.

NOTE: If "Y" connector can be attached directly to cold water faucet, go to Step 6. If "Y" connector cannot be attached directly to the cold water faucet, the short hose must be used. Continue with Step 3.

3. Attach short hose to cold water faucet. Screw on coupling by hand until it is seated on

faucet.

4. Using pliers, tighten the couplings with an additional two-thirds turn.

Using pliers, tighten the couplings with an additional two-thirds turn.

A. Inlet to co/(] water

NOTE: Do not overtighten. Damage to the coupling can result.

9. Attach angled end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill valve connector.

10. Using pliers, tighten the coupling with an additional two-thirds turn.

NOTE: I)o not overtighten. Damage to the coupling can result.

5. Attach "Y" connector to brass male end of small hose. Screw on coupling by hand until it is seated on connector.

6. Attach straight end of long hose to "Y" connector.

7. Attach washer cold inlet hose to other end of "Y" connector. Screw on coupling by hand until it is seated on connector.

NOTE: I)o not overtighten. Damage to the coupling can result.

11. Check that the water faucets are on.

12. Check for leaks around "Y" connector, faucet and hoses.

Checkthelevelnessofthedryerbyfirstplacingalevelonthetopofthedryernearthe console.

Ioosen the top screw from each of the 2 hinges in Step 2.

-A

Then,byplacingalevelinthecreaseonthesideofthedryerbetweenthetopofthedryerand thedryercabinet,checkthelevelnessfromfronttoback.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.

You can change your door swing from a right-side opening to a left-side opening, if desired.

1. Place a towel or soft cloth on top of the dryer or work space to protect the surface.

Remove the door assembly

1. Open the dryer door.

2. Remove the bottom screw from each of the 2 hinges that attach the dryer door to the front panel of the dryer.

A. Loosen these screws.

t:3.Remove these screws.

4. Remove the dryer door and the hinges by lifting upward on the door. I.ay the door on a flat, protected surface, with the inside of the door facing up. Remove remaining 2 loose

screws from dryer front panel.

5. Remove the 4 plastic plugs located outside the dryer door opening.

location of plastic

plugs shown

Install 4 plastic plugs into screw holes in the dryer left where the hinges were removed in Step 4.

+ 44 hidden pages