Maytag MDG7500AWQ, MDG6800AWW, MDG6800AWQ, MDG6800AWB, MDG9800AWW Installation Instructions

NEPTUNE DRYER INSTALLATION INSTRUCTIONS

MISE EN SERVICE SÉCHEUSE NEPTUNE

I N S T RUCCIONES DE INSTA L ACIÓN DE LA SECADORA NEPTUNO

The installation, including a proper exhaust system,

is the responsibility of the owner.

La responsabilité de la mise en service, y compris le système

d'évacuation qui convient, revient au propriétaire.

Es responsabilidad del propietario la instalación correcta,

incluso la del sistema de escape.

LEAVE THESE INSTRUCTIONS WITH THE OWNER

REMETTRE CES INSTRUCTIONS AU PROPRIÉTAIRE

DEJE ESTAS INSTRUCCIONES CON EL PROPIETARIO

Printed in U.S.A., Printed in U.S.A. • Impreso en los Estados Unidos • Stampato negli Stati Uniti 6 3714120

Read this before you start…

Tools needed for installation

ITEMS PROVIDED

• Teflon tape or pipe
joint compound (gas only)

• Cutting knife

• Pipe wrench (gas only)

• Nut drivers

• Level

Electric Dryer

Only

Gas Dryer

Only

• Screw driver (standard)

• Duct tape

• Crescent wrench

Proper installation is the responsibility of the owner.
HOWEVER, SERVICE CALLS PERFORMED AS A RESULT OF POOR SET-UP, ADJUSTMENT AND CON-

NECTION ARE THE RESPONSIBILITY OF THE INSTALLER.

Make sure you have everything necessary for proper installation.

1. GROUNDED ELECTRICAL OUTLET is required. See Electric Requirements.

2. POWER CORD for electric dryers (except Canada).

3. GAS LINES (if a gas dryer) must meet National and Local Codes.
4 . E X H AUST SYSTEM – must be rigid metal or flex i ble stiff walled metal exhaust ducting. See Exhaust R e q u i r e m e n t s.

3/4”

(1.9 cm)

43 1/4”

(109.9 cm)

minimum

36 1/4”

(92.1 cm)

minimum

6 13/16”

1 1/2”

(3.81 cm)

(17.3 cm)

IMPORTANT TO INSTALLER

Base

Exhaust

27 1/2”

(69.9 cm)

(9.2 cm)

3/8” minimum

(1 cm)

22 1/4”

(56.5 cm)

3 5/8”

16”

(40.6 cm)

Gas Pipe

2 7/16”

(6.2 cm)

3 7/16”

(8.7 cm)

3 1/4”

(8.3 cm)

13 1/2”
(34.3 cm)

(68.9 cm)

Base

Exhaust

27”

PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY BEFORE STA RTING TO INSTALL T H E
D RY E R . THESE INSTRUCTIONS SHOULD BE RETAINED FOR FUTURE REFERENCE.

REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES SUCH AS DRYERS TO AVOID THE
DANGER OF A CHILD SUFFOCATING.

L O C ATION CONSIDERAT I O N S

The dryer should be located to permit adequate room in front for loading the dryer, and sufficient room behind
the dryer for the exhaust system.

This dryer is factory-ready for rear exhaust. To exhaust out the bottom or left side, use the accessory exhaust
kit (see Accessories). Instructions are included with the kit.

It is important to make sure the room has adequate make-up air. The area where the dryer is located must not
o b s t ruct the flow of combustion or ventilating air.

On gas drye r s, adequate clearance as noted on the data plate must be maintained to insure adequate air fo r
c o m bustion and proper operation of the drye r.

THE DRYER MUST NOT BE INSTALLED OR STORED IN AN AREA WHERE IT WILL BE EXPOSED TO
WATER AND/OR WEATHER. THE DRYER AREA IS TO BE KEPT CLEAR AND FREE FROM
COMBUSTIBLE MATERIALS, GASOLINE AND OTHER FLAMMABLE VAPORS AND LIQUIDS. A DRYER
PRODUCES COMBUSTIBLE LINT. THE AREA AROUND THE DRYER SHOULD BE KEPT FREE OF LINT.

ALCOVE OR CLOSET INSTALLATION

An appliance installed in a closet shall have no other fuel-burning appliance
installed in the same closet.

Each opening area in the door must have a minimum of 36 square inches.
These openings must not be obstructed. (Louvered door with equivalent air
opening is acceptable.)

CLOSET DOOR

36”

sq.ins.

(91.4 cm)

17”

(43.2 cm)

3”

(7.6 cm)

0”

Minimum installation clearances. If possible,
more clearance is recommended.

0”

FRONT VIEW SIDE VIEW

0”

2” (5.1 cm) 3” (7.6 cm)

36”

sq. ins.

(91.4 cm)

WARNING –

The dryer must
be exhausted to
the outside to
reduce the risk
of fire when

installed in an a l c ove or closet.

MOBILE HOME INSTALLATION

The installation of the dryer in mobile homes must confo rm to the Manu factured Home Construction and Saf e t y
Standard Title 24 CFR, P a rt 32-80 {fo rm e rly the Fe d e ral standard for Mobile Home Construction and Safe t y, T i t l e
24, HUD (Pa rt 280), 1975} for the United States,) or CSA Standards Z240 (for Canada).

When installing a dryer in a mobile home, provisions for anchoring the dryer to the floor must be made. A n
anchor bra cket kit is ava i l a ble with instructions (see Accessori e s ) . Locate in an area that has adequate make
up air. A minimum of 25 square inches (63.5 cm) of unobstructed opening is required.

All mobile home installations must be exhausted to the outside with the exhaust duct termination securely
fastened to the mobile home structure, using materials that will not support combustion. The exhaust duct
may not terminate beneath the mobile home. See the section on exhausting for more information.

EXHAUSTING

Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the
room.

In the United States:

•all gas drye rs must be exhausted to the outside.

• electric drye rs located in a confined area such as a bedro o m , b a t h ro o m , or closet must be ex h a u s t­ed to the outside.

• electric dryers not located in a confined area may be exhausted to the inside (see nonexhausted
installations).

In Canada:

•all gas and electric dryers must be exhausted to the outside.

Outside the U.S. and Canada:

• refer to local codes.

WARNING – plastic or nonmetal flexible duct presents a potential fire hazard.
NEVER USE PLASTIC OR NONMETAL FLEXIBLE DUCT.

If your existing ductwo rk is plastic, nonmetal or combu s t i bl e, replace it with metal. Use only metal
exhaust duct that will not support combustion to insure the containment of exhaust air, heat and lint.

Plastic fle x i ble duct can kink, sag, be punctured, reduce air
f l ow, extend drying times and affect dryer opera t i o n .

USE A MINIMUM OF 4-INCH (10.2 cm) DIAMETER
RIGID ALUMINUM OR RIGID GALVANIZED STEEL
DUCT. Do not use smaller duct. Ducts larger than
4 inches (10.2 cm) in diameter can result in increased
lint accumulation. Lint accumulation should be cleaned
regularly. If flexible metal duct must be used, use the
type with a stiff sheet metal wall. Do not use flexible
duct with a thin foil wall. Serious blockage can result if
flexible metal duct is bent too sharp. Never install any
type of flexible duct in walls, ceilings or other concealed
spaces.

Keep exhaust duct as straight and short as possibl e.
Exhaust systems longer than recommended can ex t e n d
d rying times, affect machine operation and may collect
l i n t . Secure joints with duct tape. Do not use screw s.

DO NOT EXHAUST DRYER INTO ANY WALL,
CEILING, CRAWL SPACE OR A CONCEALED SPACE
OF A BUILDING, GAS VENT, ANY OTHER COMMON
DUCT OR CHIMNEY. THIS COULD CREATE A FIRE
HAZARD FROM LINT EXPELLED BY THE DRYER.

Exhaust Hood Type

Number

of

90° Turns

4” (10.2 cm) 2-1/2” (6.4 cm)

Maximum length of 4-inch (10.2 cm) diameter

rigid metal duct

0
1
2
3
4

Maximum length of 4-inch (10.2 cm) diameter

0
1
2
3
4

65 ft.(165.1 cm)
54 ft.(137.2 cm)
44 ft.(111.8 cm)
36 ft. (91.4 cm)
28 ft. (71.1 cm)

flexible stiff walled metal duct

36 ft. (91.4 cm)
32 ft. (81.3 cm)
28 ft. (71.1 cm)
25 ft. (63.5 cm)
23 ft. (58.4 cm)

59 ft.(149.9 cm)
48 ft.(121.9 cm)
38 ft. (96.5 cm)
30 ft. (76.2 cm)
22 ft. (55.9 cm)

28 ft. (71.1 cm)
24 ft. (60.9 cm)
20 ft. (50.8 cm)
17 ft. (43.2 cm)
15 ft. (38.1 cm)

The exhaust duct should end with an exhaust hood with a swing out damper to prevent backdrafts and entry
of wildlife. Never use an exhaust hood with a magnetic damper. The hood should have at least 12 inches
(30.5 cm) of clearance between the bottom of the hood and the ground or other obstruction. The hood
opening should point down. Never install a screen over the exhaust outlet.

When possible, do not exhaust the dryer directly into a window well in order to avoid lint build-up. Do not
exhaust under a house or porch.

If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly down
towards the exhaust hood to reduce condensation and lint build-up.

If an existing exhaust system is to be used with your new dryer, you must be sure:

• The exhaust system meets all local, state and national codes.

• That plastic flexible duct is not used.

• To completely inspect and clean all lint accumulation from the interior of the duct.

• The duct is not kinked or crushed.

• The exhaust hood damper opens and closes freely.

The static pressure in any exhaust system must not exceed 0.92 inches of water column, or be less than 0.
This can be measured with the dryer running with a manometer at the point where the exhaust duct connects
to the dryer. A no heat setting should be used. The dryer tumbler should be empty and the lint filter clean.

Inspect and clean the interior or the exhaust system at least once a year. Disconnect electrical service prior
to cleaning. Check the gas line on gas dryers anytime the dryer is moved.

Frequently check to be sure the exhaust hood damper opens and closes freely.

NONEXHAUSTED INSTALLATIONS

If the electric dryer is not exhausted to the outside, the exhaust must not terminate directly behind the dryer.
Use a rectangular vent kit along with a dacron mesh lint bag (see Accessories). Maintain a 6” (15.2 cm)
clearance between the back of the control panel and the wall. Although the lint screen and lint bag will retain
most of the lint, a certain amount will be expelled into the laundry area.

WARNING: IF THE DRYER IS NOT EXHAUSTED TO THE OUTSIDE, SOME FINE LINT WILL BE
EXPELLED INTO THE LAUNDRY AREA. AN ACCUMULATION OF DUST OR LINT IN ANY AREA OF THE
HOME CREATES A FIRE HAZARD. ANY LINT ACCUMULATIONS MUST BE CLEANED FREQUENTLY.

GAS REQUIREMENTS

Use only Natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES,OR IN THE ABSENCE OF LOCAL CODES,
WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES),
OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner orifice for operation on NATURAL gas. If the dryer is to be operated
on LP (liquid propane) gas, it must be converted for safe and proper performance and must be
converted by a qualified service technician. Conversion kits from NATURAL to LP, or LP to NATURAL are

available through your local Maytag dealer (see Accessories). If other conversions are required, check with
the local gas utility for specific information concerning conversion requirements.

A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8”(1.0 cm) gas line
on the drye r.

The National Fuel Gas Code requires that an accessible, approved manual gas shut off valve be installed
within 6 feet of the dryer.

Additionally, a 1/8” (.3 cm) N.P.T .(National Pipe Thread) plugged tapping, accessible for test gauge
connection, must be installed immediately upstream of the gas supply connection to the dryer.

The dryer must be disconnected from the gas supply piping system during any pressure testing of the system.
DO NOT re-use old flexible metal gas line. Flexible gas line must be design certified by American Gas

Association (CGA in Canada). NOTE: Any pipe joint compound used must be resistant to the action of any
liquefied petroleum gas.

NOTE: As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION –

This dryer uses an automatic ignition system to ignite the bu rn e r. There is no constant burning pilot.

ELECTRICAL REQ U I R E M E N T S

NOTE: Wiring diagram is located inside the control console.
Export models (not U.S. or Canada): See Additional Instructions for Export Models on the other side of this

sheet.

WARNING – To prevent unnecessary risk of fire, electrical shock or personal injury,all
wiring and grounding must be done in accordance with local codes, or in the
absence of local codes, with the National Electrical Code, ANSI/NFPA (for the United
States) or the Canadian Electrical Code CSA C22.1 (for Canada).

GROUNDING

This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of
electrical shock by providing a path of least resistance for electrical current.

GAS MODELS

This appliance is equipped with a cord having an
equipment-grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance
with all local codes and ordinances.

Do not modify the plug provided with the appliance – if
it will not fit the outlet, have a proper outlet installed by a qualified electrician.

If a separate ground is required by local codes, an accessory ground wire and ground clamp is available.
Connect ground wire to back of unit with the cabinet ground screw and washer. The ground screw and
washer are found in the parts package. Secure other end of ground wire to a suitable external ground
connection. The wire may be secured with the clamp to a grounded COLD metal water pipe.

NEVER CONNECT GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES OR HOT WATER PIPES.

WARNING – Improper connection of
the equipment grounding conductor can
result in a risk of electric shoc k . C h e ck
with a qualified electrician or serv i c e­man if you are in doubt as to whether
the appliance is properly g r o u n d e d .

ELECTRIC MODELS

U. S. e l e c t ric models are shipped with a ground strap connected from the neutra l
t e rminal bl o ck post to the frame of the drye r. If local codes prohibit the use of the
ground stra p, the dryer must be grounded in accordance with local codes.

If a power cord is not used and the electric dryer is to be permanently wired, the drye r
must be connected to a grounded metal, permanent wiring system; or an
equipment grounding conductor must be run with the circuit conductors and
connected to the equipment grounding term i n a l .

ELECTRICAL CONNECTIONS

BEFORE OPERATING OR TESTING, follow all grounding instructions in

Grounding Section.
An individual branch (or separate) circuit serving only this appliance is recommended. DO NOT USE AN

EXTENSION CORD.

Ground

Screw

G A S MODELS – U. S .and Canada

A 120 volt, 60 Hz AC, approved electrical serv i c e, with a 15 ampere fuse or circuit breaker is required.

ELECTRIC MODELS – U. S . O n ly

Most U. S.d rye r s, as manu factured, require a 120/240 volt, 60 Hz AC approved electrical serv i c e. Some require
120/208 volt, 60 Hz approved electrical serv i c e. The electric service requirements can be found on the data
label located on the front behind the door. A 30 ampere fuse or circuit breaker on both sides of the line is
r e q u i r e d .

A 120/240 volt U.S. electric dryer must be converted if it is to operate on a 120/208 volt electrical system.
A heating element conversion kit is available (see Accessories).

If a power cord is used, the cord should be plugged into a 30 ampere receptacle.
The power cord is NOT provided with U.S. electric model dryers.
IMPORTANT: When permitted by local codes, the dryer electrical supply may be connected by means of a

new power supply cord kit, marked for use with clothes dryer, that is U.L. listed, rated at 120/240 volts
minimum, 30 amperes with three No.10 copper wire conductors terminated with closed loop terminals, open­end spade lugs with turned up ends or with tinned leads.

Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring must be retained
at the dryer cabinet with a suitable UL listed strain relief.

If the dryer is to be installed in a mobile home or an area where local codes do not permit grounding through
neutral, only a 4 conductor power cord, rated and terminated as above, may be used.

ELECTRIC MODELS – Canada Only

A 120/240 volt, 60 Hz AC approved electrical service fused through a 30 ampere fuse or circuit breaker on
both sides of the line is required.

All Canadian models are shipped with the power cord attached. The power cord should be plugged into a
30 ampere receptacle.

NOTE: It is not permissible to convert a dryer in Canada to 208 volts.

REPLACEMENT PARTS AND ACCESSORIES

If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your
dryer or Maytag Customer Service, Box 2370, Cleveland, Tennessee 37320-2370, phone [phone], for
information on the nearest authorized Maytag Parts Distributor.

INSTALLATION

Parts and literature are packaged inside of dr yer drum.

To Install…

1. Move dryer to an appropriate location for installation. Consider installing the

dryer before the washer in side-by-side installations, to allow access to gas,

electrical and exhaust connections.
Lay two of the carton corner posts on the floor. Tip the dryer forward on its

front so it will lay across both corner posts.

2. Remove the crate wires holding the crate base to the base frame. This can

be done with a screwdriver.

3. Loosen the leveling locking nuts and install the vinyl feet.

4. Set the dryer back in an upright position.

5. R ev i ew the exhaust section on the reverse side before installing the

exhaust system. Install the ductwo rk from the dryer to the exhaust hood.
The crimped end of the duct sections must point away from the drye r.
D O N OT use sheet metal screws when assembling ducting. These joints
should be taped. N ever use plastic flex i ble exhaust material.

Tip for tight installations: install a section of exhaust system to the dryer
before moving the dryer in place. Use duct tape to secure this section to
the dryer but do not cover louvers in dryer cabinet.

• Improper connection of the equipment-grounding conductor can result in a risk of electrical
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether
the appliance is properly grounded. Do not modify the plug provided with the appliance –
if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

• To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring and
grounding must be done in accordance with the National Electrical Code ANSI/NFPA, No.

70-Latest Revision (for U.S.) or the Canadian Electrical code CSA C22.1 – Latest Revision and local
codes and ordinances. It is the personal responsibility and obligation of the appliance owner to provide
adequate electrical services for this appliance.

• All gas installations must be done in accordance with the National Fuel Gas Code ANSI/Z2231 – Latest
Revision (for the United States) or the CAN/CGA – B149 Installation Codes – Latest Revision (for
Canada) and local codes and ordinances.

6. GAS DRYER SECTION

Review gas requirements on back side of these instructions.

Remove the pipe thread protective cap.
Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded

connections. NOTE: Pipe joint compound must be resistant to the action of any liquefied
petroleum gas.

Connect the gas supply to the drye r. An additional fitting is required to connect the 3/4”
(1.9 cm) female thread end of a flexible connector to the 3/8” (1 cm) male threaded end
on the dryer. Securely tighten the gas line fitting over threads.

Turn on the gas supply. Check all gas connections for leaks using a soap solution. If

bubbles occur, tighten the connections and recheck. DO NOT use an open flame to

check for gas leaks.

6. ELECTRIC DRYER SECTION

Review electrical requirements on back side of these instructions.

BEFORE OPERATING OR TESTING, follow the grounding directions on the reverse side.

U.S. MODELS:
IMPORTANT – All U.S. models are produced for a 3-WIRE SYSTEM

CONNECTION. The dryer frame is grounded to the neutral conductor at the
terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or
remodeled construction, mobile homes, or if local codes do not permit grounding

Terminal

Block Cover

Plate

through neutral. If the 4-wire system is used, the dryer frame cannot be
grounded to the neutral conductor at the terminal block. Refer to the following
instructions for 3- and 4-WIRE SYSTEM CONNECTIONS.

Remove the terminal block cover plate.
Insert the power cord with a U.L. listed strain relief through the hole provided in the cabinet near the

terminal block. NOTE: a strain relief must be used.
Do not loosen the nuts already installed on the terminal bl o ck . Be sure they are tight. Use a 3/8” (1 cm)

deep well socke t .

3-WIRE SYSTEM CONNECTIONS

If the power cord has terminals, place the terminals over

the existing nuts on the posts. The neutral (white or center
wire on power cord) conductor must always be connected
to the center (silver colored) post of the terminal block.

Secure in place using the nuts provided in the parts

package. If the power cord does not have terminals, use

the cupped washers ahead of the nuts.

Neutral

Post

3-Wire System

Ground

Strap

Be sure the terminal bl o ck nuts are tight. Secure the powe r
cord in position. Tighten the strain relief screw(s) in order to
clamp the strain relief to the cord.

Replace the terminal block cover.
WARNING: If converting from a 4-wire electrical system

to a 3-wire, the ground strap must be reconnected to the
terminal block support to ground the dryer frame to the
neutral conductor.

Neutral

Strain

relief

4-WIRE SYSTEM CONNECTIONS

Remove the ground strap screw from the terminal block
support. Fold the ground strap over so both ends of the
ground strap will be attached to the center terminal block

post.

Connect the neutral (white) conductor of the cord to the
center (silver) post of the terminal bl o ck . Connect the
grounding (green) wire of the cord to the terminal bl o ck
s u p p o rt using the ground strap screw.

Connect the red and black wires of the cord to the outer
posts of the terminal block.

Be sure the terminal block nuts are on tight. Secure the
power cord in position. Tighten the strain relief screw(s) in
order to clamp the strain relief to the cord. Replace the
terminal block cover.

EXPORT MODELS

Refer to the Additional Instructions Section.

7. With a level, check the dryer, and make necessary

adjustments to the leveling legs. Once level, tighten the
leveling leg locking nuts with a wrench.

Neutral

Post

120

VAC

240/208

VAC

4-Wire System with

Power Cord Attached

Folded

Ground

Strap

Neutral

Strain

relief

8. The dryer door direction can be reversed.

1. If the dryer is plugged in, unplug from electrical service.

2. Remove the hinge hole covers and screws. Move the door
catch cover to the opposite side.

3. While supporting the door remove 2 screws in the hinges
that secure the hinges to the cabinet.

4. Remove the door by lifting slightly at the hinges and pulling the hinge tabs out of the hinge slots.

5. Move the following parts to the opposite side of the door: 2 hinges and 4 hinge screws, 4 door
screws, door strike and screw, inner door cover plate and screw.

6. Attach the door to the opposite side of the cabinet using the 2 counter sunk hinge screws.
(See below.)

7. Driving the lower hinge screw first will help to align the door and hinges.

8. Replace the hinge hole covers and screws in the opposite side.

9. At this time, make sure all gas, exhaust and electrical connections are complete. Plug dryer in, and

check operation by using the check list below.

10. (GAS MODELS ONLY)

The burner may not ignite initially due to air in the gas line. Allowing the dryer to operate on a heat
setting will purge the line. If the gas does not ignite within five minutes, turn the dryer off and wait
5 minutes. Be sure the gas supply to the dryer has been turned on. In order to confirm gas ignition,

check the exhaust for heat.

FINAL INSTALLATION CHECK LIST

n Dryer is plugged into electrical outlet and is properly grounded.
n Exhaust duct work is hooked up and joints taped.
n Plastic flexible duct is NOT used.
n Use rigid or stiff walled flexible metal vent material.
n Dryer is level with all legs firmly on the floor, with the lock nuts tightened.
n Vinyl feet have been installed.
n Gas Models – gas is turned on, there are no gas leaks.
n Dryer runs, heats, shuts off.
n Demonstrate use to consumer.

HOUSEHOLD INSTALLATION ACCESSORIES

•V ent hood – 4” (10.16 cm) opening – 059129

•Aluminum pipe – 4” x 24” (10.16 cm x 60.96 cm) – 059130

•Aluminum elbow – 4” (10.16 cm) – 059131

•Aluminum window plate – 15” x 20” (38.10 cm x 50.80 cm) – 4” (10.16 cm) hole – 059134

•Flexible aluminum vent duct – 4” (10.16 cm) diameter – 38” (81.28 cm) length stretches to 8’ (2.44 cm) –
304353

•Clamp for flexible aluminum duct – 304630

•Exhaust duct kit for base or left side ex h a u s t i n g – 12001453

•Rectangular vent kit – 059144

•Dacron lint bag – 311353

•NATURAL to LP conversion kit – 306195

•LP to NATURAL conversion kit – 306204

•Anchor bracket kit – 303740

•Heating element conversion kit, 208V., not for Canada– 308590

•Grounding wire – 311155

•Grounding clamp – 301548

•Power cords – 240 v, 30 A

4’ (121.9 cm) – 3-wire – 33001780
5’ (152.4 cm) – 3-wire – 33001822
6’ (182.9 cm) – 3-wire – 33001823

10’ (304.8 cm) – 3-wire – 33001838

4’ (121.9 cm) – 4-wire – 33001781
5’ (152.4 cm) – 4-wire – 33001824
6’ (182.9 cm) – 4-wire – 33001825

10’ (304.8 cm) – 4-wire – 33001838

For the visually impaired, Braille labels can be placed on the control panel of the appliance. Check with your
local Association for the Blind for information on Braille label makers.