Maytag MDC4650AWW, MDC4650AWB, MDC4650AWW3, MDC4650AWW2, MDC4650AWW1 Owner’s Manual

MAYFAG

®

MDB-7

Dis

D Operating Tips .............. 3

Loading ................... 4

Dishwasher Use ............. 5

Cycles, Options

and Lights ............... 6-7

Care & Cleaning ............ 8

PortableDishwashers ........ 9

Troubleshooting ........ 10-12

Warranty & Service ........ 13

Guide d'utilisation

et d'entretien .............. 14

Gui_ de uso y cuidado ...... 25

Part No. 6 920109 A www.maytag.com _2005 Maytag Appliances Sales Co.

SnfetyInstructions

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in this
guide are not meant to cover all possible conditions and
situations that may occur. Common sense, caution and care

must be exercised when installing, maintaining or operating

the dishwasher.
Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

Important Safety Instructions

1. Read all instructions before using the dishwasher.

2. Use the dishwasher only for its intended function.

3. Disconnect electrical power to dishwasher before
attempting to service.

4. To avoid electrical shock hazard, the sides and back
must be enclosed and the front panels must be attached

before electrical power is applied to the dishwasher.
Refer to the installation instructions for proper grounding
procedures.

5. Connect to a properly rated, protected and sized power
supply circuit to avoid electrical overload.

6. Children should never be permitted to operate, or play
in, with, or around this dishwasher.

Z To reduce the risk of injury when loading items to be

washed, sharp or pointed items should be located with the

handles up. Also, load sharp items so they are not likely to
damage the door seal.

8. Do not touch the heating element on the bottom of the
tub during or at the completion of a cycle. It will be hot.

9. Use only detergents and rinse additives designed for a
residential automatic dishwasher. Never use soap,
laundry detergent, or [land washing detergent in your
dishwasher. Keep these products out of reach of

children.

10. Do not sit, stand on or abuse the door or dish racks of
the dishwasher.

11. Under certain conditions, hydrogen gas may be produced
in a [lot water system that has not been used for two

weeks or more. Hydrogen gas is explosive. If the hot
water system has not been used for such a period, turn

on all hot water faucets and let the water flow from each
for several minutes. This will release any accumulated

hydrogen gas. As the gas is flammable, do not smoke or
use an open flame during this process.

12. Do not wash plastic items unless marked "dishwasher
safe" or the equivalent. Forplastic items not so marked,

check the manufacturer's recommendations.

13. Do not tamper with controls.

14. To prevent accidental child entrapment and suffocation
risks, always remove the door to the washing
compartment when removing an old dishwasher from
service or discarding it.

15. Use caution when unloading the dishwasher. Dishes will
be [lot if unloaded shortly after a cycle has completed.

16. Certified residential dishwashers are not intended for
licensed food establishments.

1Z To avoid water, mold or mildew damage to your home,

inlet and drain hose connections should be checked
periodically for leaks.

Products with a _ label have been listed with
Underwriter's Laboratories, Inc. - those with a CSA tag [lave

been listed with Canadian Standards Association.
Nevertheless, as with any other equipment using electricity

and moving parts, there is a potential hazard.

Save These Instructions

for Future Reference

SafetyInstructions

WhatCanandCannotBeWashed

Most tableware, cookware and flatware can safely be washed in your dishwasher. Check with the manufacturer.

: ....

Aluminum Yes, except anodized. High water temperature and detergents may affect finish.

Cast Iron No Seasoning will be removed, and iron will rust.

China/Stoneware Yes, except antique or Always check manufacturer's recommendation before washing.

hand-painted. Antique, hand-painted or over-the-glaze patterns may fade. Gold

leaf may discolor.

Crystal Yes, except antique or Always check manufacturer's recommendation before washing.

delicate crystal. Some types of leaded crystal may etch with repeated washings.

Filters Not recommended. May leave a dingy deposit or stain on dishwasher interior.

Glass Yes A specialty glass called milk glass can yellow with repeated

dishwasher washing.

Gold-Plated No Will discolor.

Flatware

Pewter, Tin No

Plastics Yes, top rack, except Always check manufacturer's recommendation before washing.

disposable plastic Plastics vary in their capacity to withstand high water
items, temperatures and detergents. Disposable plastic items are not

dishwasher safe for this reason.

Stainless Steel Yes Run a Rinse Only cycle (select models) if not washing

immediately. Prolonged contact with foods containing salt,

vinegar, milk products or juice could damage finish.

Sterling Silver or

Silverplate

No, if has commercial
"darkening".

Always check manufacturer's recommendation before washing.

Run a Rinse Only cycle (select models) if not washing
immediately. Prolonged contact with food containing salt, acid or

sulfide (eggs, mayonnaise and seafood) could damage finish.
Commercial "darkening" may be removed by detergent.

Wooden Items No Wood may warp, crack or discolor.

2

Opermin9Tips

Before You Start

• Don't prerinse. Simply scrape off any bones or

large food particles.

• If connected to a food waste disposer, make certain

the disposer is empty before starting the
dishwasher,

• Scrape off tomato-based food soils (see page 8).

• Remove certain foods such as mustard,
mayonnaise, lemon juice, vinegar, salt or dressings

from stainless steel flatware as soon as possible.

These foods may cause rusting and pitting if allowed
to remain in contact with the surface for an extended

period of time.

Operating the Dishwasher

1. After loading the dishwasher and adding detergent,

select the desired cycle by pressing the cycle select

pad until the light next to the desired cycle is
illuminated. Choose the desired options by pressing

the pads. The indicator lights for the selected cycle

and options will illuminate. To cancel an option
press the pad again.

2. To start a cycle, close the door until it latches then

press the START/Cancel pad once. After a pause,

the fill will begin. The display countdown (select

models) will flash until START/Cancel is pressed.

Note :

If START/Cancel is not pressed within 30

seconds of choosing your cycle, the dishwasher
will turn off.

The dishwasher remembers your last cycle so you

do not have to reset the cycle each time. To start
the dishwasher using the same cycle and options
selected on the previous wash, just press the
START/Cancel pad.

To cancel a running cycle, press the START/Cancel

pad once. The dishwasher will drain, then shut off.
To turn the dishwasher off without draining, press
the START/Cancel pad twice. To prevent

unplanned cycle or option changes, these selections

are "locked in" after 1 minute.

Adding a Forgotten Item

For best cleaning, the forgotten item should be added
early in the cycle.

1. Grasp door handle and unlatch door without
opening completely. All lights will flash to indicate
that the cycle is suspended.

2. Wait for the water circulation to stop.

3. Open the door and add the item.

4. Close and latch the door. Lights will stop flashing
when the door is properly shut. After a slight delay,
the cycle resumes automatically at the point of
interruption.

Notes:

• If the door is opened during a running cycle,
there may be up to a 30 second delay before the

dishwasher restarts after closing the door.

• Extended interruption of the wash cycle is not
recommended.

General Recommendations

(Rack features vary by model)

• Items can be centered behind a single tine or loaded
at an angle to maximize space.

• Avoid blocking or preventing the spray arms from
spinning freely. Do not allow items to extend beyond

the racks.

• Face soiled surfaces toward the center of the
dishwasher.

For best dishwashing results follow these guidelines to
determine the best arrangement for your items.

10 Place Setting Load

(Rack features vary by model)

Upper Rack

Note :

If the cycle select pad is pressed after the
controls have been "locked in", the light above the

current cycle will flash three times.

Lower Rack

Loading

Upper Rack

Glasses, cups, stemware, light-weight plastics, plates,
bowls, pans, long-handled utensils etc. can be loaded
in this rack. Do not load glasses over the tines.

The Stack-Rack (select
models) on the right side
of the upper rack folds

up or down for loading
flexibility. Fold it down to
hold long-handled
knives, spatulas and spoons or short items like cups or

juice glasses. Fold it up for taller items like glasses,

bowls, plates, etc.
The edge of the Stack-

Rack (select models) is
designed to hold
stemware in place. Taller

stemware will fit better on
the right side as the upper

rack is deeper on this side.
The Cup Clips (select

models) located in the
center of the upper rack

can be used to hold
light-weight plastic items,

cooking utensils, knives,
etc. in place. Clip the

item between the tine
and the clip.

Lower Rack

A variety of items such as dinner plates, mixing bowls,
pots and pans and baking dishes can be loaded in this

rack.
Wider items can be placed along the left side and

back of this rack.

slotted covers, load knives, handles up and spoons
and forks handles down.

Be sure that thin, finely pointed items do not extend

through the basket. This could block the lower wash
arm.

Auxiliary Basket (select models)

Use this supplemental
basket in the upper or

lower rack for loading
miscellaneous items and

utensils. This is also a safe
place to load sharp knives

and pointed items.

Removing the Upper Rack

The upper rack can be removed when tall or oversized

items need to be loaded into the lower rack. Unload

the rack before removing it from the dishwasher.

To remove rack:

.

Roll the rack '/3to '/2of the way out.

2.

To remove each plastic push tab rack stop from the
end of each track, push inward (toward the rack) on
the ridged area of the rack stop. The rack stop will
snap open and can be easily removed by pulling
straight out. Take care to support the track while

removing rack

stops.

.

Roll the rack all the

way out of the
track and remove

from the
dishwasher.

To replace: Push Tab

• Reverse the above Rack Stop
procedure to replace the rack into the dishwasher.

Utensil Basket

Removable Standard Utensil Basket

(style may vary)

For best cleaning results, prevent
items from nesting together by
placing some items in the basket
with handles up and some with

handles down. On models with

Important:

The dishwasher will not
operate correctly if the

wash arm is not aligned
with one of the water inlet

holes on back wall of the
dishwasher.

4

DishwasherUse

Hot Water

For optimal cleaning and drying results, hot water
is necessary. The incoming water temperature
should be 120 ° F [49 ° C) to properly activate the

detergent and melt greasy food soils.

To check the incoming water temperature, turn on the

hot water faucet nearest the dishwasher and let it run

into a glass in the sink. Place a candy thermometer in
the glass and check the temperature once it has
stopped rising.

Detergent

Use a detergent designed specifically for use in an
automatic dishwasher. Be sure it is fresh. Store

granular detergent in a cool, dry place (not under the

sink).

Recommended Amount

Too little detergent results in poor cleaning, hard water
filming/spotting and poor drying. Too much detergent

can cause permanent etching/cloudiness.
Suds can cause the dishwasher to overflow. Measure

the detergent carefully and use only detergents
designed for use in a dishwasher. Less detergent is

needed in soft water. Try another brand of detergent if
sudsing continues.

The amount of detergent to use is determined by the

hardness of the water and soil level of the load. Refer
to the following chart for detergent usage

recommendations.

softener may be necessary to improve water
quality, detergent effectiveness, and protect the

dishwasher parts from the damage that hard
water can cause.

Add recommended amount of detergent to each cup
as shown and close the detergent lid.

Do not use detergent with the Rinse Only (select

models) cycle. Leave the detergent lid open when
running Rinse Only (select models).

Rinse Aid

Regular use of a rinse aid improves drying,
reduces spotting and filming, and reduces

moisture left on the dishwasher interior.

An automatic rinse aid dispenser is located next to the
detergent cup.

The window next to the dispenser cap indicates when
the rinse aid reservoir needs to be refilled. When the

level of rinse aid is below the indicator marks and the

window is nearly clear, it is time to refill the dispenser.

Check the dispenser monthly.

LightSoil 2 tsp 6 tsp

Soft (0-4 gpg) Normal Soil 4 tsp 6 tsp

Heavy Soil 4 tsp 7 tsp

Light Soil 4 tsp 6tsp

Medium (5-9 gpg) Normal Soil 4 tsp 6tsp

Heavy Soil 5 tsp 7 tsp

Hard (10-12 gpg) All Levels 5 tsp 8tsp

*Your local water utility or state university extension service can tell

you the degree of water hardness in your area.

In extremely hard water conditions (13 grains per
gallon or more*), it is difficult to achieve good

results with any dishwasher. A mechanical water

To add rinse aid to the
dispenser, turn the cap

counterclockwise to open.
Remove the cap and pour
liquid rinse aid into the

opening. The amount of

rinse aid dispensed during

the cycle is adjustable by moving the lever inside the

reservoir area. For most water conditions use the
manufacturer recommended setting of "2". Adjust it up to

the "MAX" setting for hard water. Set the lever anywhere

between these amounts as needed to get the best results.
Replace the cap and turn it clockwise to close.

5

Cycles,OptionsandLights

Cycles

Choose the cycle that best describes your dishload by pressing the cycle select pad. (See page 3, Operating

Tips, for how to begin the cycle).

Heavy Wash Longcycle for heavy food soils. 132" 2washes/3 rinses

Normal Wash soils. The turbidity sensor is 97-117" 1-2 washes**/1-2 rinses**

Light Wash Short cycle for light food soils. 82* 1wash/2 rinses

Rinse Only Rinses dishes being held until 9 1rinse

(select models) there is a full load.

Includes approximately 30 minutes of dry time.

**Number of fills will vary depending on the soil level of each load.

Notes:

• Depending on water temperature, there may be time added to the cycle to bring water up to temperature.

• Only the following certified cycles have been designed to meet NSF requirements (NSF/ANSI 184 Residential
Dishwasher) for sanitization: Heavy Wash, Normal Wash and Light Wash.

Medium cycle for average food
active with this cycle.

Cycle Options

In addition to choosing a cycle, choose as many available options as are needed for your dishload.

Sanitizes dishware. When the cycle monitor recognizes that the proper Heavy Wash*

Sanitize conditions have been met, SANITIZED light will activate at the end of the cycle. Normal Wash*

[select models) Sanitization may not be achieved if there is an interruption of the cycle, Light Wash*

Extra Rinse Adds an additional rinse to cycle. An extra rinse helps to improve results All cycles

[select models) in hard water situations. (except Rinse Only

Heated Dry

* Only these cycles have been designated to meet NSF requirements (NSF/ANSI 184 Residential Dishwasher) for sanitization.

power failure or if the incoming water temperature is below 120° F(49° C).

For enhanced drying results, select this option. When Heated Dry is not
selected, towel drying of some items such as plastic and itemswith non-stick
surfaces may be necessary and more moisture may be noticed adhering
to the dishwasher interior. In models with plastic interiors, it is normal to
notice vapor escaping from the door vent as the heat dries your dishes.
Vapor will escape even if Heated Dry is not selected.

[select models[)

All cycles

(except Rinse Only

[select models])

Options

START/Cancel Operating the Dishwasher, for explanation.

Delay for instructions.

Starts and stops dishwasher. See page 3 under Operating Tips: All Cycles

Used to automatically start the cycle at a later time. See page 7 All Cycles

6

Cvcles,OptionsandLights

Lights/Display

Delay

The Delay option can be used to automatically start
the cycle at a later time to reduce daytime heat

buildup in the home or to take advantage of reduced
energy costs if available in your area. This option is
also useful for conserving hot water at times of high
household usage (showers, laundry).

To set up a Delay:

1. Select the appropriate cycle and options for the
load. Close the door.

2. Press the Delay pad until the desired amount of
delay time is selected.

3. The Delay indicator and the count down display
(select models) will flash until the START/Cancel

pad is pressed.

/4. As soon as the START/Cancel pad is pressed, the

flashing will stop and the delay time will begin

counting down. The Delay indicator will remain lit

until the delay time has counted down.

.

The cycle will automatically start as soon as the
delay time expires.

Note:

If 30 seconds elapse between setting the cycle
and options and pressing the START/Cancel
pad, the dishwasher will turn off.

To cancel a Delay:
When the delay is counting down, press the Delay pad

again. The indicator light will go out and the cycle will
start or resume immediately.

To cancel a Delay and the cycle:

• Press START/Cancel once to drain and turn off the

dishwasher.

Or

• Press START/Cancel twice to turn dishwasher off
without draining.

Lights/Display (select models)

CLEAN Light seconds continuously.

WASH/DRY Light Illuminates during all rinse, wash and dry portions of the cycle.

SANITIZED Light Illuminates at the end of the cycle when conditions have been met to achieve

(select models) sanitization. The light will remain lit until the door has been open for 30 seconds

Notes:

• When Sanitize is selected, cycles are monitored to assure sanitization. The SANITIZED light will not activate if sanitization
requirements are not met. This could happen if the cycle is interrupted, power failure occurs or incoming water

temperature is below 120° F (49° F).

• The CLEAN and SANITIZED indicator lights (select models) will not relight after a power failure until after the next cycle is run.

Illuminates at the end of the cycle and remains lit until the door has been open for 30

continuously.

CareandCleaning

General Recommendations

• The dishwasher interior is normally self-cleaning.
Periodically check the bottom of the dishwasher tub

to see if any large particles remain.

• Wipe the edge of the inner door liner to remove any

food soil splashes which occurred during loading.

• When cleaning stainless steel, always wipe with the
grain. Never use products containing chlorine bleach
or citric acid.

Standard Exterior Light to moderate Soft damp cloth and liquid spray cleaner. Do

Stainless Steel Exterior

(select models)

Interior Light to moderate

Daily cleaning and light soil

Moderate to heavy soil

Streaks or fingerprints/restore shine

Discoloration

Discoloration, or tomato-based stain

• The color from some tomato-based food soils may
occasionally adhere to various components of the
dishwasher interior, causing temporary discoloration.

To minimize this:

• Remove excess tomato-based food soils from
dishes, prior to loading.

• Run the Heavy Wash cycle when washing loads
containing tomato-based food soils.

• Use a dishwasher detergent that contains chlorine

to better fight staining.

Not use abrasive powders or cleaning pads.
Soft cloth or sponge and one of the following:

• Mild detergent and water

• A solution of white vinegar and water

• Formula 409 Glass and Surface Cleaner*, or
similar multi-surface cleaner.

• Do Not use products containing chlorine
bleach or citric acid.

Follow with rinse and dry.
Soft cloth or damp sponge and Bon Ami*.

Follow with rinse and dry.
Soft cloth and Stainless Steel Magic Spray**.
Soft cloth or damp sponge and Cameo

Stainless Steel Cleaner*. Rinse immediately
and dry.

Soft cloth or damp sponge.
Switch dishwasher detergent to chlorine-

based product.

*Brand names are trademarks of the respective manufacturer. **Call 1-877-232-6771 U.S. or 1-800-688-8408 Canada to order.

Storage/Moving

Fill detergent cup with a fresh-scented dishwasher
detergent or baking soda and select the Normal Wash
cycle. Allow the dishwasher to complete the cycle. Then
turn the water supply off and drain the dishwasher. To
drain, press the START/Cancel pad once to activate

the dishwasher. Press START/Cancel again to activate
the drain. Operate the drain twice to ensure most of

the water is removed. Last, disconnect the electrical

supply and prop open the door.

When turning the water supply to the home off, the
water shut off at the dishwasher must be turned off also.

PortableDishwashers

Connecting a Portable

1. Turn on the faucet at the sink until the water runs hot.

Turn off the faucet.

2. Pull the connector from the recess in the back of

the dishwasher.

3. Press down on the thumb release and lift the

connector onto the faucet.

4. Remove pressure from the thumb release and tug

slightly on the connector to be sure it is securely in
place.

5. Turn the hot water on full force.

6. Check that the sink drain is open so water from the

dishwasher can drain properly.

7. Pull the electrical cord from the recess. Plug it into

a properly grounded outlet.

8. Select the proper cycle and options for the load and

start the dishwasher.

Disconnecting a Portable

1. Be sure to turn the water supply off and press the
pressure release button BEFORE removing the

connector.

2. Press down on the thumb release and remove the
connector from the faucet.

3. Push the connector and hoses back into the cabinet

recess.

4. Unplug the electrical cord and push it back into the
cabinet recess.

Button

Care and Cleaning

Clean the cabinet and laminate top with a soft damp
cloth and liquid spray cleaner.

To polish and protect the laminate top, use a product

specifically developed for countertops such as Hope's
Countertop Polish*.

Apply an appliance wax to the cabinet once a year.

Note: To protect the laminate top from
damage, do not use it as a cutting surface or

resting place for warm/hot cookware. Do not
slide ceramic or other hard or abrasive

objects across the surface.

* Brand names are the trademarks of the respective

manufacturer.

9

Troubleshooting

CHECK THESE POINTS TO HELP SAVE YOU TIME AND MONEY.

Dishwasher will not fill • Press the START/Cancel pad to start the dishwasher.

• Be sure door is latched securely.

• Be sure the water is turned on.

• Check that the pad is properly selected for a cycle.

• Check your home's circuit breaker or fuse box.

• Check inlet hose for a kink.

• Check water valve inlet for sediment and clean if necessary.

Dishwasher will not drain/
water in tub bottom

Dishwasher adds water at • This is normal. The sensor (select models) in the pump must stay submerged so a

end of cycle short fill of water is added after the cycle's last drain.
Detergent cup is not empty • Check that the cycle is completed.

Dishwasher seems noisy

• If hooked up to a food waste disposer, be sure the knock-out is removed from the
disposer inlet.

• Check for food obstruction in the drain or disposer.

• Check drain hose for a kink.

• Check your home's circuit breaker or fuse box.

• Check that the cycle is completed.

• Be sure dispenser is not blocked.

• Use fresh detergent stored in a cool, dry place.

A water valve hiss during fill is normal.
Water circulation sounds are normal.

A thumping sound may be a wash arm bumping an item that is extending beyond tile

racks. Readjust load to avoid obstructing wash arm.
Chopping or grinding sounds may be heard as the internal food disposer chops hard

items like fruit seeds, nuts, etc.
Humming during tile drain is normal.

A snap noise is the detergent cup lid hitting the door liner when the dishwasher door

is opened at the end of tile cycle. This is normal.
Proper installation affects the noise level.

Cycle takes too long (Heating
Delay light [select models]

stays on)

Dishwasher has an odor

Dishwasher leaks

*Brand names are trademarks of the respective manufacturer.

• Sanitize has been selected and the cycle is extended to heat water.

• Check to see that the incoming water temperature is 120° F (49° C).

Run dishes being held in the dishwasher through a Rinse Only cycle (selectmodels).
Many dishwashers (lavea "new" smell when first installed. This will dissipate with use.
Dishwasher may not be draining properly. (See "Dishwasher Will Not Drain" section.)
For a strong odor, place baking soda in both sides of the detergent cup. Select Light

Wash cycle and allow the water to circulate for about 10minutes. Interrupt the cycle

by unlatching the door and let it stand overnight. Restart the dishwasher by latching
the door and allow it to complete the cycle. Another alternative is to use a dishwasher
cleaning product such as Jet-Dry Dishwasher Cleaner*.

Check that the dishwasher is level. (Refer to the Installation Instructions.)
Suds carl cause the dishwasher to overflow. Measure the detergent carefully and use

only detergents designed for use in a dishwasher. Less detergent is needed in soft

water. Tryanother brand of detergent if sudsing continues.

Follow directions closely on (low to add a forgotten item (pg. 3).

To avoid rinse aid leaking from the dispenser, be sure the lid is securely attached.

Cont.

10

Troubleshooting

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!E!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!_....

Display time suddenly drops • This is normal when the Normal Wash cycle is selected and the dishwasher decides
or increases by several to skip or add a drain and refill.
minutes (select models)

Indicator lights flashing

Glasses are cloudy/spotted

Food soil remains on dishes

• The countdown display ([selectmodels_)flashes after a cycle is selected until the
START/Cancel pad is pressed.

• The countdown display ([selectmodels_)and the delay indicator flash after a delay is
selected until the START/Cancel pad is pressed.

• All active display indicators flash if the door is opened during a running cycle or delay.

• The currently selected cycle flashes if an attempt is made to change the cycle after
cycle "lock-in".

• Select Extra Rinse ([select models_).

• Check water temperature. Incoming water should be 120° F([49° C_).

• Always use a rinse aid.

• Confirm that the cloudiness is removable by soaking the item in white vinegar for
approximately 5 minutes. If removed, the problem is due to hard water. Adjust
detergent amount being used to match water hardness ([pg.5_).Be sure detergent is
fresh, stored properly and is a high quality brand.

• If cloudiness is not removable, it is etching. This is an erosion of the surface of the
glassware and can be caused bywater that is too [lot, from using too much detergent

or by prewashing. Detergent needs food soil to act upon. If etching has occurred, the
glassware is permanently damaged. To prevent further etching, adjust the detergent

amount to match the water hardness, stop prewashing, and use water heating options
only when incoming water temperature is below 120° F ([49° C_).

• Check water temperature. Incoming water should be 120° F ([49° C_).

• Run hot water at the sink before starting the dishwasher.

• Check water hardness and adjust detergent amount accordingly ([pg.5_).

• Use fresh detergent stored in a cool dry place.

• Select proper cycle for the soil level ([pg.6).

• Make sure the upper rack wash arm connector is correctly aligned in one of the water
inlet holes (pg. 4_).

• Load items so they do not block the wash arms (pgs. 3-4_).

• Load the utensil basket with knife handles up and spoon and fork handles down.

• Do not place glasses over tines.

• Priorto loading,scrape off burnt on foodsand wipe the starchy film from utensils used with
pasta,rice and oatmeal. Thesesoils require more energy than the rest of the load to clean.

Items washed in the
dishwasher or the dishwasher

tub itself are stained/
discolored

*Brand names are trademarks of the respective manufacturer. Cont.

• Aluminum utensils or pans can leave marks when they rub against other items. Leave
a slight space between items.

• Iron deposits in the water can leave a yellow, brown or orange film on dishes or the
dishwasher tub. A rust filter may be needed. Check with a water treatment company.

• Separate silver or silver-plated silverware from stainless steel. These metals can be
damaged by contact with each other during washing.

• Color from tomato sauces mayadhere to the interior parts of the dishwasher (pg. 8_).If
light staining has occurred, leave the door open to oxidize the stain away. Use a
dishwasher detergent that contains chlorine to better fight staining.

• Certain dishwasher detergents may stain silver. Tryanother brand of detergent.

11