Maytag MDBF550AWW, MDBF550AWB, MDBF550AWQ Dimension Guide

www.dexpress.com DIMENSION EXPRESS Fax on Demand (775) 833-3600
This Data Sheet Includes Information On
Maytag
• Product Model Number (s): •
24" Dishwashers:
MDBF550AWW, MDBF550AWB and MDBF550AWQ
22 1/2"
2 5/8"
Side View
(not to scale)
• Dimensions (Actual Size) •
Depth:
35 1/4" Maximum 33 1/2" MinimumHeight at 0" leg adjustment: 23 7/8"Width: 22 1/2" 2 5/8" 1 3/4" 51 1/2" 3" to 4 1/4" n/a n/a
Height at full leg adjustment:
Door thickness incl. control panel:
Door thickness:
Depth with door open:
Vertical toe space:
Custom panel flange depth:
Custom panel flange width:
• Additional Information •
DRAIN:
• 32" Drain loop, 1/2" minimum I.D. Floor drains require a siphon break.
• Drain hose extension kit available 904024.
• When draining into a disposer, make sure disposer drain plug is removed. WATER SUPPLY:
• 15 to 120 psi water pressure. 120°F to 140° hot water supply recommended.
• Access for manual shut-off valve recommended.
• 3/8" female pipe thread connection is attached to water valve.
• Suggested water line size 3/8" O.D. copper or equivalent. ELECTRICAL SUPPLY:
• 115 volts, 60 Hz protected by a GROUNDED 15 amp fuse or comparable circuit breaker.
• Max amperage draw 12.0 amps.
• Minimum wire size 14 gauge (No. 12 wire preferred) ­Copper only. Check all local codes.
• Individual circuit for dishwasher recommended.
• IMPORTANT: ALWAYS CHECK LOCAL AND NATIONAL
CODES FOR FULL COMPLIANCE.
See page 2 for additional information
Front View
(not to scale)
Plumbing and
electrical service
must enter inside
shaded area
51 1/2"
35 1/4" Maximum
33 1/2" Minimum
Rough-in Information
1 3/4"
23 7/8"
Panel Size:
3/4" or 1/4" Thick
23 5/16" Wide
25" High
(Not to Scale)
Wall area
must be free
of pipes and
wires
35 1/4" Maximum 33 1/2" Minimum
X X
3" to 4 1/4"
Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or outdated data sheets. Because of the difficulty or impracticability of deter­mining actual damages, liability of Dimension Express shall not exceed $50.00. Copyright © Dimension Express, 2002.
• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at (775) 833-3633 • notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory • it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am • Sheets for each project, as opposed to the problems, time, costs, and risks associated with reusing old Data Sheets.
456
underside of
countertop
to floor
3"
33 1/2" - 35 1/4"
8"
5"
BN177 • A456B149 • • 032005 • 121834 • 68274
4" from floor
5" from
back wall
www.dexpress.com
DIMENSION EXPRESS
Fax on Demand (775) 833-3600
Additional Information:
• Electrical and water supplies should enter cabinet opening on the floor, or through the side walls as shown in shaded areas of drawing
• Keep back free of drain, water and electrical supply.
• Connections preferably located toward left side of dishwasher. Care should be taken to route plumbing and electrical away from motor and other electrical components.
• When installing the dishwasher in or near a corner, allow enough room for the door to open without interfacing with any cabinet drawers or hardware.
Kit: DAX3000AXX (Black Trim Kit) Kit: DAX3000AXN (Bisque Trim Kit) Kit: DAX3000AXE (White Trim Kit)
Page 2
This Data Sheet Includes Information On
Maytag
• Product Model Number (s): •
24" Dishwashers:
MDBF550AWW, MDBF550AWB and MDBF550AWQ
Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00. Copyright © Dimension Express, 2002.
• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at (775) 833-3633 • notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory • it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am • Sheets for each project, as opposed to the problems, time, costs, and risks associated with reusing old Data Sheets.
BN177 • A456B149 • • 032005 • 121834 • 68274
149
Loading...