Maytag MBS1976AAP, MBS1976AAB Installation Instructions

Form No. C/02/10/04 Part No. 381-90-000300 www.skyboxbymaytag.com

Important Safety Instructions

What You Need to Know About Safety Instructions

Warning and Important Safety Instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining or operating this appliance.

Always contact your dealer, distributor, service agent or manufacturer about problems or conditions you do not understand. Please refer to your SkyBox™ by Maytag™ Personal Beverage Vendor User Guide for Important Safety Instructions.

Recognize Safety Symbols, Words, Labels

WARNING – Hazards or unsafe practices which COULD result in severe personal injury or death.

WARNING

CAUTION – Hazards or unsafe practices which COULD result in minor personal injury or property damage.

CAUTION

DANGER – Immediate hazards which WILL result in severe personal injury or death.

DANGER

SkyBox™ by Maytag™

SkyBase™ Stand

Table of Contents

Important Safety Instructions.................................... cover

Product Overview.................................................................... 1

Installation Location .............................................................. 1

Assembly.................................................................................1-3

Care and Cleaning...................................................................3

Customer Service.................................................................... 3

Français........................................................................................4

Espagnol......................................................................................8

Product Overview

Your new SkyBase™ Stand is a sturdy, level stand that is able to hold approximately 200 pounds of weight and will safely accommodate your fully stocked SkyBox™ personal beverage vendor. The SkyBox™ personal beverage vendor securely mounts to this SkyBase™ stand. The stand also provides additional, unrefrigerated storage. Consider it your bullpen, bench or pit area!

Installation Location

• SkyBox™ personal beverage vendor is designed for indoor use only with room temperatures between 50° – 80° F (10° – 27° C).

• Allow a minimum of 5" (127 mm) clearance from the door hinges to a side wall to allow the door to swing open. Allow 3" (77 mm) of clearance behind the SkyBox™ personal beverage vendor and 1" (26 mm) clearance on all other sides for ease of installation. Additional space is required above the main unit to change the front or side display panels.

To avoid serious risk of injury, DO NOT lift or move the SkyBox™

personal beverage vendor and/or SkyBase™ stand

when loaded with beverages or when the door is open.

WARNING

Assembling Your SkyBase™ Stand

Carefully unpack the stand parts (see below) from the packaging.

Tools Needed:

• #2 phillips head screw driver • Level

• Adjustable Wrench

Parts Quantity

A End Frame.......................................................................................................2

B Long Support Rail.......................................................................................4

C Rear Leveling Legs (attached to end frames)..............................2

D Shelves..............................................................................................................2

E Pan-Head Screws.....................................................................................24

F Left Side Panel (with hinge holes) .....................................................1

G Right Side Panel (with no hinge holes)...........................................1

H Back Panel......................................................................................................1

I Door....................................................................................................................1

J Hinges (attached to the door)..............................................................2

K Front Foot.........................................................................................................2

L M5 x 16 Hex-Phillips Head Cap Screw -

⁄

” (16mm) long....6

M Front Foot Leveling Head........................................................................2

N Flat Head Screws.........................................................................................6

FF M5 x 20 Hex-Phillips Head Cap Screw -

⁄

” (20mm) long....2

• IMPORTANT: For safety, the unit should be displayed in a secure, level area, with the

back of the unit securely against a wall, with 3" (77 mm) of clearance. The wall installation is to prevent anyone, including children, from getting behind the unit and tipping it over, causing personal injury.

WARNING

• Use caution when installing the unit on vinyl or hardwood floors so as not to mark or otherwise damage the flooring. A piece of plywood, a rug or other material should be used to protect the floor while positioning the unit.

• Once assembled and loaded with beverages, the SkyBox™ personal beverage vendor with SkyBase™ stand weighs up to 300 pounds (136 kg), so select a location that will not require frequent moving.

• Moving the loaded SkyBox™ personal beverage vendor may cause damage to the unit.

STE

P 1 – Assemble Frame of Stand

• Connect one long support rail (B) to one of the end frames (A) by inserting the tabs on the support rail into the slots of the end frame and pressing downward. The support rails will temporarily lock into place when pressed downward.

• Connect the other end of support rail to a second end frame (A) by inserting the tabs on the support rail into the slots of the end frame and pressing downward.

•Repeat procedure for remaining 3 rails, creating a basic frame for the cabinet. DO

NOT INSTALL ANY SCREWS (E) DURING THIS STEP!

Important

Wall

Installation

• Place back panel (H) over frame and side panels

by aligning screw holes on the back of the unit. Attach back panel using six pan-head screws (E). During this process, the screws will also secure the back of the left and right side panels.

STEP 4 – Assemble Exterior Panels

•Lower the top lip of the left side panel (F) over the

top of end frame, aligning screw holes in side panel with holes in the corner post. Make sure panel is positioned to accommodate hinges for door on front left side. Attach panel by installing three pan-head screws (E) down the front of the unit and two pan-head screws (E) along the top rail.

•Position the right side panel (G) over frame of

cabinet, aligning screw holes in side panel with holes in corner post. Attach panel by installing three pan-head screws (E) down the front of each side panel and two pan-head screws (E) along the top rail.

STEP 3 – Install Shelves

• Place bottom shelf (D) on top of lower support rails. Align screw holes and install four pan-head screws (E).

• Repeat procedure for center shelf (D), which mounts on the four tabs welded to the end frames (A).

TEP 2 – Level the Stand

• Attach the two front feet (K) to the bottom of the two corner posts using three M5 x 16,

⁄8 ” (16 mm) long, Hex-Phillips head cap screws (L) for each foot.

NOTE: The threaded bolt on the front foot must extend outward away from the frame (see figure).

• Attach the front foot leveling head (M) to the threaded bolt on each front foot (K).

• Carefully place the partially assembled stand on the floor where it will be displayed. Adjust the front foot leveling heads (M) down so that the front foot roller is just off the floor. Using a level and an adjustable wrench, adjust the two rear leveling legs (C) so the unit sits squarely on the floor.

STEP 5 – Attach Door to

SkyBase™ Stand

•Position door (I) on the front of the stand by aligning screw holes in the hinges (J) with hinge holes in the left side panel on the front of the stand.

• Attach door hinges (J) to the left side panel (F) using three flat-head screws

(N) in each hinge.

N/J

x 3

K/M

Lx 3

To avoid electrical shock, which can cause severe personal injury or death, unplug the refrigerated personal beverage vendor unit before cleaning.

WARNING

The modular design of your SkyBox™ personal beverage vendor and SkyBase™ allows for easy cleaning. Most spills can be cleaned up with a damp cloth or sponge. If using a household cleaner, choose a mild, non-abrasive cleaner that will not scratch or dull the surface of your unit. Do not allow beverage spills to stand; clean up right away.

To avoid spills, do not store previously opened or partially consumed bottles/cans in the SkyBox™ personal beverage vendor.

Customer Service

If you have questions regarding your SkyBox™ by Maytag™ Personal Beverage Vendor, call MAYTAG Customer Service at 1-877-366-5426 U.S.A. or 1-800-688-2002 Canada. They may be able to assist you with troubleshooting product difficulties. U.S. Customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080 (Mon.-Fri., 8 a.m.-8 p.m. Eastern Time).

Care and Cleaning

Attach SkyBox™ Personal Beverage Vendor to SkyBase™ Stand

• Place the SkyBox™ personal beverage vendor on the SkyBase™ stand.

• IMPORTANT: Line up holes on bottom of SkyBox™ personal beverage vendor with holes in top of SkyBase™ stand. Carefully thread a connecting bolt (FF–see illustration) into each hole up through the inside of the stand and into the hole in the SkyBox™ vendor. Secure firmly.

+ 8 hidden pages