Maytag MBB2256GEB Owner’s Manual

Form No. A/02/03 Part No. 12642726 h t t p : / / w w w . m a y t a g . c o m 16022155 Litho U.S.A.

BOTTOM FREEZER REFRIGERATOR

Installer: Please leave this manual with

this appliance.

Consumer: Please read and keep this manual for future reference. Keep sales

receipt and/or cancelled check as proof of purchase.

If you have questions, write us (include your model number and phone number) or call:

Maytag Services

Attn: CAIR®Center P.O. Box 2370 Cleveland, TN 37320-2370 1-800-688-9900 U.S.A. 1-800-688-2002 Canada 1-800-688-2080 (U.S.A. TTY for hearing or speech impaired) (Mon.-Fri., 8 a.m.-8 p.m. Eastern Time) Internet: http://www.maytag.com

For service information, see page 21.

In our continuing effort to improve the quality and performance of our appliances, it may be necessary to make changes to the appliance without revising this guide.

Page 1

Pages 2-7

Page 8

Page 11

Pages 9-10

Pages 12-13

Page 14

Pages 14-16

Page 17

Pages 18-19

Page 21

Page 22

Page 44

Model Number

Serial Number

Date of Purchase

operating sounds

food storage tips

looking inside

ice service

proper temperatures

installation

storing the refrigerator

safety

care & cleaning

before you call

Safety

What you need to know about safety instructions

Warning and Important Safety Instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution, and care must be exercised when installing, maintaining, or operating refrigerator.

Always contact your dealer, distributor, service agent, or manufacturer about problems or conditions you do not understand.

Save these instructions

DANGER – Immediate hazards which WILL result in severe personal injury

or death.

DANGER

WARNING – Hazards or unsafe prac-

tices which COULD result in severe personal injury or death.

WARNING

CAUTION – Hazards or unsafe prac-

tices which COULD result in minor personal injury.

CAUTION

To reduce risk of fire, electric shock, serious injury or death when using your refrigerator, follow these basic precautions, including the following:

WARNING

To reduce risk of injury or death, follow basic precautions, including the following:

IMPORTANT: Child entrapment and

suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they sit out for “just a few days.” If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.

Before you throw away your old refrigerator or freezer:

➢ Take off the doors. ➢ Leave the shelves in

place so children may not easily climb inside.

DANGER

RECOGNIZE SAFETY SYMBOLS, WORDS, LABELS

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not sure this appliance is properly grounded.

5. DO NOT ground to a gas line.

6. DO NOT ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate 103 to 126 volt, 15 amp., 60 cycle line. DO NOT modify plug on power cord. If plug does not fit electrical outlet, have proper outlet installed by a qualified electrician.

8. DO NOT use a two-prong adapter , extension cord or power strip.

9. DO NOT remove warning tag from power cord.

10. DO NOT tamper with refrigerator controls.

11. DO NOT service or replace any part of refrigerator unless specifically recommended in User Guide or published user-

repair instructions. DO NOT attempt service if instructions are not understood or if they are beyond personal skill level.

12. Always disconnect refrigerator from electrical supply before attempting any service. Disconnect power cord by grasping the plug, not the cord.

13. Install refrigerator according to Installation Instructions. All connections for water, electrical power and grounding must comply with local codes and be made by licensed personnel when required.

14. Keep your refrigerator in good condition. Bumping or dropping refrigerator can damage refrigerator or cause refrigerator to malfunction or leak. If damage occurs, have refrigerator checked by qualified service technician.

15. Replace worn power cords and/or loose plugs.

16. Always read and follow manufacturer’s storage and ideal environment instructions for items being stored in refrigerator.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

2. Remove toe grille and bottom bracket cover(s).

• Open freezer door as wide as

possible.

• Depending on the model of your

refrigerator, you may have one or two bracket covers.

3. Remove top hinge cover from refrigerator door by removing Phillips screw.

• Retain screw and

cover for replacement.

4. Unscrew

⁄16" hex head

screws from top hinge to remove hinge.

• Retain all screws for

later use.

5. Lift refrigerator door from center hinge pin.

6. For freezer door models only: Hold freezer door while removing hinge pin with a

⁄16

"hex head driver.

Remove door from bottom hinge.

• Retain hinge pin for later use.

For freezer drawer models only:

Remove center hinge pin with a

⁄16" hex

head driver.

• Retain hinge pin for later use.

7. Remove Phillips screws to remove center hinge.

• Retain all screws

for later use.

8. Remove bottom hinge or stabilizing bracket with

⁄8" hex head driver.

• Retain screws for

later use.

• Lift out bottom hinge

pin (select models).

Installation

Your new refrigerator was packed carefully for shipment. Remove and discard shelf packing clips (if used) located just above each shelf where they hook onto the frame. To remove plastic clips wiggle the clips sideways and pull straight out.

Measuring the opening

⁄2" of air space should be provided for the

top and back of the refrigerator. When installing your refrigerator, measure carefully.

Subflooring or floor coverings (i.e. carpet, tile, wood floors, rugs) may make your opening smaller than anticipated.

Some clearance may be gained by using the leveling procedure under How to

Level Your Refrigerator (page 7). IMPORTANT: If refrigerator is to be

installed into a recess where top of refrigerator is completely covered, use dimensions from floor to top of hinge cap to verify proper clearance.

Transporting your refrigerator

Follow these tips when moving the refrigerator to final location:

➢ NEVER transport refrigerator on its

side. If an upright position is not possible, lay refrigerator on its back. Allow refrigerator to sit upright for approximately 30 minutes prior to plugging refrigerator in to assure oil return to the compressor. Plugging refrigerator in immediately may cause damage to internal parts.

➢ Use an appliance dolly when moving

refrigerator. ALWA YS truck refrigerator from its side or back–NEVER from its front.

➢ Protect outside finish of refrigerator

during transport by wrapping cabinet in blankets or inserting padding between the refrigerator and dolly.

➢ Secure refrigerator to dolly firmly with

straps or bungee cords. Thread straps through handles when possible. DO NOT overtighten. Overtightening restraints may dent or damage outside finish.

Selecting the best location

Observe these points when choosing the final location for your refrigerator:

➢ DO NOT install refrigerator near oven,

radiator or other heat source. If not possible, shield refrigerator with cabinet material.

➢ DO NOT install where temperature

falls below 55° F (13° C). Malfunction may occur at this temperature.

➢ Make sure floor is level. If floor is not

level, shim rear wheels of refrigerator with a piece of plywood or other shim material.

➢ To assure proper door closure, verify

that the refrigerator is leveled with a

⁄4"

tilt to the back.

How to remove the doors and hinges

Some installations require door removal to get refrigerator to final location. If removal of the pullout drawer is required, see later section entitled How to

Remove and Install the Pullout Drawer

(page 5).

To avoid electrical shock which can cause severe personal injury or death, observe the following:

➢ Disconnect power to refrigerator

before removing doors. Connect power only after replacing doors.

WARNING

To avoid damage to walls and flooring, protect soft vinyl or other flooring with cardboard, rugs or other protective material.

CAUTION

1. Unplug power cord from power source.

safety

How to reverse the doors

1. Perform all steps listed in How to

Remove the Doors and Hinges

(page 2).

2. Transfer cabinet plugs and cabinet screws to opposite side of cabinet.

• Remove cabinet

plugs with flat blade of screwdriver tip wrapped in masking tape.

• Remove center mullion screws with

⁄16" hex head screwdriver.

• For swing doors only: Remove

bottom mullion screws with

⁄8" hex

head driver.

3. Transfer door stops from bottom edge of fresh food door and freezer door (select models) to opposite side of door edge.

• Use a Phillips

screwdriver for removal and installation.

4. See How to Install and Remove Handles (page 3) to remove and reinstall handles.

5. Proceed to How to Replace the Doors and Hinges to mount doors (page 4).

To avoid possible injury and damage to property, place doors on a nonabrasive surface protected by towels or rugs while working directly on doors.

CAUTION

* Fasteners may require either a T-15 Torx®driver or a Phillips screwdriver.

Torx®is a registered trademark of Textron Inc.

Installation,

cont.

How to install and remove handles

For easier installation, some refrigerators may have been delivered with the handles off. Please see the interior of the fresh food section, or the back of your refrigerator, to locate the handle assembly. In case future transport of the refrigerator is necessary, or panels need to be removed and replaced, the removal instructions have been included here for your convenience.

Handle design may vary from refrigerator to refrigerator. Please reference the instructions for the appropriate handle design below.

FRESH FOOD HANDLES

Installing Front-Mounted Handles

1. Remove

⁄4" hex head

screws from door face with hex head driver, and Phillips screw from top of door.

• If reversing door, remove door plugs from opposite side of door and insert in screw holes.

2. Align handle holes with screw holes on door face and secure with 2 door face screws from step 1.

3. Locate handle trim in literature pack and install over top and bottom of handle, as illustrated.

• Secure top handle trim

with remaining screw removed in step 1.

• Snap bottom trim over

bottom portion of handle.

Removing Front-Mounted Handles

1. Remove top handle trim by removing top handle screw.

• Retain trim and screw for

later replacement.

2. Pry bottom handle trim from handle with screwdriver flat blade wrapped in masking tape.

• Retain trim for later

replacement.

3. Remove two

⁄4" hex head screws.

• Retain screws for later replacement.

Installing Side-Mounted Handles

➢ Install handle by

fastening with screws* removed from edge of door.

NOTE: If reversing door, remove door plugs from opposite side of door and insert in screw holes.

Removing Side-Mounted Handles

➢ Remove handle by

removing three screws* from side of door.

• Retain screws for

later replacement.

Installing Stainless Steel Front-Mounted Handles

1. Loosen one door clip on door with

⁄4" hex head driver .

2. Locate predrilled hole at base of handle, and fit hollow end of handle over door clip.

3. Fit other end of handle over other door clip and slide up as far as possible.

NOTE: If top of handle does not fit over top clip, loosen lower clip further until fit can be accomplished.

4. Insert

⁄4" hex head driver into predrilled

hole at base of handle to tighten screw. Insert screw plug(s) into hole(s).

Removing Stainless Steel Front-Mounted Handles

1. Remove screw plug at base of handle with a very small flat-blade screwdriver.

• Insert

⁄4" hex head driver

into predrilled hole to remove screw.

2. Slide handle to remove from door clip.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

* Fasteners may require either a T-15 Torx®driver or a Phillips screwdriver.

Torx®is a registered trademark of Textron Inc.

How to replace the doors and hinges

1. Install hinge assemblies.

• Install top hinge loosely with

⁄16" hex

head screws.

• Install center hinge with Phillips screws.

• Install bottom hinge with

⁄8" hex head

screws.

2. Insert bottom hinge pin (select models).

• Locate bottom hinge

hole closest to outside edge of cabinet, and insert bottom hinge pin. Replace any door shims, if present.

3. For freezer door models only: Place hinge side of freezer door on bottom hinge pin and hold freezer door upright while installing center hinge pin with

⁄16" hex

head driver.

• Replace any applicable door shims.

• Make sure the hinge pin is installed

tightly.

For freezer drawer models only:

Install center hinge pin with a

⁄16" hex

head driver.

• Replace any applicable door shims.

• Make sure the hinge pin is installed tightly.

4. Place hinge side of refrigerator door on center hinge pin.

5. While holding refrigerator door upright, tighten down top hinge with

⁄16"

hex head driver and replace hinge cover.

installation

FREEZER HANDLES

Installing Partial-Width Handle

➢ Install handle by

fastening with screws removed from edge of door.

• If reversing freezer door, remove door plugs from top edge of door and insert into screw holes.

Removing Partial-Width Handle

➢ Remove handle by

removing screws from top of handle.

• Retain screws for later replacement.

Installing Full-Width Extruded Handle

➢ Install handle by fas-

tening with screws* removed from edge of door.

Removing Full-Width Extruded Handle

➢ Remove handle by

removing three screws* from handle.

• Retain screws for later replacement.

Installation,

cont.

3. Pull drawer open to full extension.

4. Remove Phillips screw from each side of rail system. (Select models)

5. Lift top of door to unhook door supports from rail system. Lift door out to remove.

To install:

1. Pull both rails out to full extension.

4. With drawer pulled out to full extension, insert lower basket by aligning tabs on both sides of lower basket with notches in rail assembly. Verify that the basket sides are hooked securely over the rails.

5. Slide upper basket into freezer. Make sure that rear of basket hooks behind rail catch.

3. Lower door into final position.

2. While supporting door, hook door supports into tabs located on inside of rail.

How to remove and install the pullout drawer

(SELECT MODELS)

To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before removing doors. After replacing doors, connect power.

WARNING

To avoid possible injury, product, or property damage, you will need two people to perform the following instructions.

CAUTION

To remove:

1. Pull upper basket out to full extension and lift out to remove.

2. Remove lower basket by pressing inward on basket sides, then lift basket.

To prevent accidental child entrapment or suffocation risk, DO NOT remove the divider in the top freezer basket.

DANGER

Press Tab Here

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

How to connect the water supply for optional automatic ice maker

MATERIALS NEEDED

➢

⁄4

" outer diameter flexible copper tub-

ing

➢ Shut-off valve (requires a

⁄

4" hole to be

drilled into water supply before valve attachment)

➢ Needle-nose pliers ➢ Adjustable wrench ➢ Water bucket ➢ Flat-blade screwdriver ➢

⁄4" hex nut driver

➢ Phillips screwdriver ➢ Masking tape or small plastic bag

➢ Create service loop with tubing using

care to avoid kinks in tubing.

➢ Remove plastic cap from water valve

inlet port.

➢ Place brass nut and sleeve on copper

tube end as illustrated.

➢ Place end of copper tubing into water

valve inlet port. Shape tubing slightly – DO NOT KINK – so that tubing feeds straight into inlet port.

➢ Slide brass nut over

sleeve and screw nut into inlet port. Tighten nut with wrench.

IMPORTANT: DO NOT overtighten. Cross threading may occur.

➢ Pull on tubing to

confirm connection is secure. Connect tubing to frame with water tubing clamp and turn on water supply. Check for leaks and correct, if present.

➢ Monitor water connection for 24

hours. Correct leaks, if necessary.

NOTE

❚ Add 8' to tubing length needed to

reach water supply for creation of service loop.

Brass

Nut Sleeve

To avoid property damage or possible injury, follow basic precautions, including the following:

➢ Consult a plumber to connect

copper tubing to household plumbing to assure compliance with local codes and ordinances.

➢ Confirm water pressure to water

valve is between 20 and 100 pounds per square inch. If water filter is installed, water pressure to water valve must be a minimum of 35 pounds per square inch.

➢ DO NOT use a self-piercing, or

⁄16" saddle valve! Both reduce

water flow, become clogged over time, and may cause leaks if repair is attempted.

➢ Tighten nuts by hand to prevent

cross threading. Finish tightening nuts with pliers and wrenches. Do not overtighten.

➢ Wait 24 hours before placing refrig-

erator into final position to check and correct any water leaks.

CAUTION

To reduce the risk of injury or death, follow the basic precautions, including the following:

➢ Read all instructions before

installing ice maker.

➢ DO NOT attempt installation if

instructions are not understood or if they are beyond personal skill level.

➢ Observe all local codes and ordi-

nances.

➢ DO NOT service ice maker unless

specifically recommended in owner’s manual or published userrepair instructions.

➢ Disconnect power to refrigerator

prior to installing ice maker.

WARNING

installation

How to level your refrigerator

If your refrigerator requires an ice maker water supply connection, proceed to How

to Connect the Water Supply for Optional Automatic Ice Maker section

(page 6) before leveling your refrigerator.

To protect personal property or refrigerator from damage, observe the following:

➢ Protect soft vinyl or other flooring

with cardboard, rugs, or other protective material.

➢ Do not use power tools when

performing leveling procedure.

CAUTION

MATERIALS NEEDED

➢

⁄8" hex head driver

➢ Level

1. Move refrigerator to final location and plug in power cord.

2. Remove toe grille and bottom cover(s).

3. Turn left and right adjustment screws (A) to raise or lower front of refrigerator.

• Make sure refriger-

ator cabinet is level from side to side by adjusting left and right roller adjustment screws.

•Turn stabilizing leg clockwise until

firmly against floor.

• For Pullout Drawer Models: After

completing the above listed steps, turn roller adjustment screws (A) 2 to 3 times counterclockwise, so that full weight of refrigerator rests on stabilizing legs.

4. Using a level, make sure front of refrigerator is

⁄4" (6 mm) or 1⁄2 bubble

higher than back of refrigerator.

• See leveling step 3 for assistance.

5. Replace toe grille and bracket cover(s). See markings on inside of toe grille to insure proper placement.

• Snap bottom portion into place

first. Press down on top part of grille until top portion snaps into place.

Installation,

cont.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

SETTING AND MAINTAINING PROPER TEMPERATURES

The controls are located at the top front of the refrigerator and freezer compartments. NOTE: The freezer control turns the cooling system on. Neither section will cool if freezer control is set to OFF.

Initial control settings

After plugging the refrigerator in, set the controls.

➢ To adjust the controls, turn the control

knob to the left or right as desired.

➢ Initially set the refrigerator control on

➢ Initially set the freezer control on 4. ➢ Let the refrigerator run at least 8-12

hours before adding food.

Wa rm cabinet surfaces

At times, the front of the refrigerator cabinet may be warm to the touch. This is a normal occurrence that helps prevent moisture from condensing on the cabinet. This condition will be more noticeable when you first start the refrigerator, during hot weather and after excessive or lengthy door openings.

TEMPERATURE CONTROL GUIDE

Refrigerator too warm Turn the refrigerator control to next higher number. Refrigerator too cold Turn the refrigerator control to next lower number. Freezer too warm Turn the freezer control to next higher number. Freezer too cold Turn the freezer control to next lower number. Turn refrigerator OFF Turn the freezer control to OFF.

NOTE: Turning freezer control to OFF stops cooling in both compartments. It does not shut off power to the refrigerator.

Adjusting the controls

➢ 24 hours after adding food, you may

decide that one or both compartments should be colder or warmer. If so, adjust the control(s) as indicated in the table below.

➢ Except when starting the refrigerator,

do not change either control more than one number at a time.

➢ Allow 5-8 hours for temperatures to

stabilize.

➢ Changing either control will have

some effect on the temperature of the other compartment.

Refrigerator Control

Freezer Control

proper temperatures

Fresh food compartment shelves

Your refrigerator has either

SpillCatcher™ or Tempered Glass Shelves.

The Spill-Catcher™ shelves have a spill retainer edge which allows for easier clean up, and some are equipped with the Easy Glide slide out feature.

To slide out (select models), grasp the front of the shelf and pull forward. Push in the shelf to return to the original position.

To remove and install 3-hook style shelf:

To remove a shelf, slightly lift up the rear of the shelf and pull the shelf straight out.

To lock the shelf into another position, tilt up the front edge of the shelf. Insert the hooks into the desired frame openings and let the shelf settle into place, being sure the shelf is securely locked at the rear.

To remove and install single hook style shelf:

To remove a shelf, slightly lift up the front of the shelf and pull the shelf straight out.

LOOKING INSIDE

DOOR STORAGE

The Pick-Off Door Bins are adjustable and can be easily removed.

To remove, lift the bin front up until it clears the retainers on the door liner then pull the bin straight out.

To replace, reverse the above procedure.

DAIRY COMPARTMENT

(Select Models)

The dairy compartment provides convenient storage for items such as butter and margarine. This compartment is an adjustable feature located in the door. It can be moved to several different locations to accommodate storage needs.

To remove:

➢ Open dairy door, pull upward and tilt

out.

To reinstall:

➢ Reverse previous

procedure.

FULL WIDTH DOOR SHELF

The lower shelf on the door is full width and not adjustable.

To remove for cleaning:

➢ Lift shelf up and out.

To reinstall:

➢ Reverse above pro-

cedure.

Special storage areas

Your refrigerator has a Snack Center Drawer (select models).

To remove the Snack Center Drawer for cleaning:

➢ Pull the drawer out until it stops. ➢ Lift the drawer up slightly and pull it out.

To reinstall the drawer:

➢ Reverse the above procedure. This drawer can be positioned as desired

on either the left or right side of the refrigerator cabinet.

For best results, keep this drawer closed tightly.

The Crispers provide storage for fruit and vegetables. There is a humidity control (select models) located on the crisper shelf above each of the crisper drawers.

➢ For fruit storage, slide the crisper control

toward the center to provide lower humidity conditions in the drawer.

➢ For vegetable

storage, slide the crisper control away from the center to provide higher humidity conditions in the drawer.

To remove a crisper drawer for cleaning:

➢ Pull out the crisper until it stops. ➢ Tilt the drawer front up and pull it out.

Never attempt to adjust a shelf that is loaded with food (except in the case of the Elevator™ Shelf).

WARNING

ELEVATOR™ SHELF

(Select Models)

The fresh food compartment is equipped with an Elevator™ Shelf. This shelf has a spill retainer edge for easy cleanup. It also has the convenient slide out feature that allows easy access to items stored at the rear of the shelf.

This shelf can be adjusted up or down without having to be unloaded of its contents. To adjust an Elevator™ Shelf, pull out the knob on the crank handle. Rotate the crank clockwise to raise the height of the shelf, and counterclockwise to lower the height of the shelf.

To remove the Elevator™ shelf for occasional cleaning, completely unload the shelf and pull the shelf forward. When the shelf stops, press up on the tabs located underneath its outside edges, then continue pulling forward, clear of the frame.

To reinstall, align the shelf to the frame and push it all the way back. (There is no need to depress the tabs for reinstallation).

In ordinary use, the Elevator™ shelf with the frame assembly does NOT require removal. Though unlikely, and not recommended, the correct removal procedure is as follows:

Unload the shelf completely, raise the shelf to its highest possible position. While supporting the shelf and frame from the front, press both locks inward. Lift slightly and tilt the frame assembly to allow the rear guides to clear the vertical rails.

To reinstall, tilt the frame assembly while depressing both locks, reposition the rear guide behind the vertical rails. When the shelf is level, release the locks allowing the shelf to latch in the correct position.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

To reinstall a crisper drawer:

➢ Align the drawer in the tracks. ➢ Lift the drawer front and slide in.

For best results, keep the crispers tightly closed.

To remove the Crisper Top (select models):

➢ Remove drawers as instructed above. ➢ Place hand beneath frame to push up

glass from underneath. Lift glass out.

➢ Lift frame from refrigerator liner rails.

To reinstall the Crisper Top (select models):

➢ Repeat above instructions in reverse

order.

If door doesn’t open far enough to remove drawers:

➢ Remove drawer furthest from hinge

side of cabinet.

➢ Remove glass as instructed previously. ➢ Lift center divider from frame. Slide

existing drawer away from hinge side of cabinet and remove.

EGG CRADLE (Select Models)

Your refrigerator may come equipped with an Egg Cradle (style may vary). It can be removed to be washed or carried to a work area.

MULTI-USE RACK

(Select Models)

The Multi-Use Rack (select models) provides a place for storing wine horizontally. The rack also holds canned beverages or an egg carton. Position the rack on the side of a refrigerator shelf. Note: The Multi-Use Rack cannot be positioned on an Elevator™ Shelf.

WIRE BASKET(Select Models)

To remove and install basket:

➢ To remove

basket, pull basket out to full extension. Tilt up front of basket and pull straight out.

➢ To install, insert basket into refrigera-

tor liner rails and push back into place.

LOWER BASKET DIVIDER

(Select Models)

The Lower Basket Divider allows the basket area to be organized into sections.

To remove divider:

➢ Pull divider

straight up.

To reinstall divider:

➢ Hook top corners of divider over top

horizontal basket rungs.

Freezer door storage

FIXED DOOR SHELF

(Select Models)

The Fixed Door Shelf provides convenient storage for frozen food items in freezer door.

To remove door shelf:

➢ Lift assembly from side liner tabs and

pull out.

To reinstall door shelf:

➢ Fit ends of shelf assembly on liner

tabs and slide down.

TILT-OUT BIN (Select Models)

The Tilt-Out Bin in the freezer door tilts forward for easy access to stored items.

Freezer compartment shelves and baskets

WIRE ICE SERVICE RACK

(Select Models)

To install:

➢ Position wire

rack against the freezer wall, above plastic supports (A).

➢ Slide the rack down over the plastic

supports until the rear loops are firmly seated.

To remove:

➢ Perform above steps in reverse order.

FIXED OR SLIDE-OUT FREEZER SHELF

(Select Models)

To remove:

➢ Pull shelf out to full extension. ➢ Tilt up front of shelf and pull straight out.

To reinstall:

➢ Insert shelf onto freezer liner rails and

push to back of compartment.

PULLOUT DRAWER BASKETS

(Select Models)

(Door assembly of drawer removed from illustration for visual clarity.)

To remove and replace baskets:

➢ See page 5 for basket removal and

replacement instructions.

To prevent accidental child entrapment or suffocation risk, DO NOT remove the divider in the top freezer basket.

DANGER

looking inside

ICE SERVICE

Your refrigerator is automatic ice maker ready. The number of the appropriate ice maker kit is IC11. The kit contains installation instructions and water connection instructions.

Other models have a factory installed ice maker. Connect the ice maker to the water supply as instructed in the separate instructions furnished with the refrigerator. Proper water flow and a level

refrigerator are essential for optimal ice maker performance.

After your refrigerator has been connected to the water supply, move the sensor arm into the down position. The ice maker will fill with water when the freezer reaches the proper temperature.

Using ice maker for the first time:

➢ Confirm ice bin is in place and ice

maker arm is down.

NOTE

❚ Energy rating guides that are post-

ed on the refrigerator at the time of purchase do not include optional ice maker energy usage.

➢ Allow approximately 24 hours after

installation to receive first harvest of ice.

➢ Discard ice created within first 12

hours of operation to verify system is flushed of impurities.

Operating instructions:

➢ Confirm ice bin is in place and ice

maker arm is down.

➢ After freezer section reaches between

0° to 2° F (-18° to -17° C), ice maker fills with water and begins operating. You will have a complete harvest of ice approximately every 3 hours.

➢ Stop ice production by raising ice

maker arm until click is heard.

➢ Ice maker will remain in the off posi-

tion until arm is pushed down.

➢ The first one or two batches will proba-

bly contain undersized and irregular cubes because of air in the supply line.

➢ The initial batch may also contain

impurities from the new water supply piping. Therefore, all cubes from the first two or three batches should be discarded.

➢ When the ice cubes are ejected it is

normal for several cubes to be joined together at the ends. They can easily be broken apart. The ice maker will continue to make ice until the supply of ice cubes raises the sensor arm, shutting the ice maker off.

➢ Certain sounds may accompany the

various cycles of the ice maker. The motor may have a slight hum, the cubes will rattle as they fall into an empty storage pan and the water valve may click or “buzz” occasionally.

➢ If the ice is not used frequently, the ice

cubes will become cloudy , shrink, stick together and taste stale. Empty the ice storage bin periodically and wash it in lukewarm water. Be sure to dry the bin thoroughly before replacing it.

➢ Beverages and foods should not be

placed in the ice storage bin for quick chilling. These items can block the sensor arm, causing the ice maker to malfunction.

➢ Turn off (arm up) the ice maker when

the water supply is to be shut off for several hours.

To remove the ice bin:

➢ Pull it forward, away from the ice

maker. To avoid the ice maker dumping ice while the bin is removed, turn the ice maker off by raising the sensor arm.

To reinstall the ice bin:

➢ Reverse the above procedure. Turn

the ice maker on by lowering the sensor arm.

Ice cube trays

Some models are equipped with ice cube trays and an ice storage bin. To release the ice cubes from a tray, hold the tray upside down over the bin and twist both ends.

Automatic ice maker (optional)

➢ After freezer section reaches between

0° to 2° F (-18° to -17° C), ice maker fills with water and begins operating.

FOR YOUR SAFETY

Do not place fingers or hands on the automatic ice making mechanism while the refrigerator is plugged in. This will help protect you from possible injury. It will also prevent interference with moving parts of the ejector mechanism and the heating element that releases the cubes.

Under certain rare circumstances, ice cubes may be discolored, usually appearing with a greenbluish hue. The cause of this unusual discoloration can be a combination of factors such as certain characteristics of local waters, household plumbing and the accumulation of copper salts in an inactive water supply line which feeds the ice maker.

Continued consumption of such discolored ice cubes may be injurious to health. If such discoloration is observed, discard the ice cubes and contact your dealer to purchase and install a water line filter.

WARNING

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

ice service

FOOD STORAGE TIPS

Fresh food storage

➢ The fresh food compartment of a

refrigerator should be kept between 34° F and 40° F with an optimum temperature of 37° F. To check the temperature, place an appliance thermometer in a glass of water and place in the center of the refrigerator. Check after 24 hours. If the temperature is above 40° F adjust the controls as explained on page 8.

➢ Avoid overcrowding the refrigerator

shelves. This reduces the circulation of air around the food and results in uneven cooling.

FRUITS AND VEGETABLES

➢ Storage in the crisper drawers traps

moisture to help preserve the fruit and vegetable quality for longer time periods. (Refer to page 9).

➢ Sort fruits and vegetables before stor-

age and use bruised or soft items first. Discard those showing signs of decay .

➢ Always wrap odorous foods such as

onions and cabbage so the odor does not transfer to other foods.

➢ While vegetables need a certain

amount of moisture to remain fresh, too much moisture can shorten storage times (especially leafy vegetables). Drain vegetables well before storing.

MEAT AND CHEESE

➢ Raw meat and poultry should be

wrapped securely so leakage and contamination of other foods or surfaces does not occur.

➢ Occasionally mold will develop on the

surface of hard cheeses (Swiss, Cheddar, Parmesan). Cut off at least an inch around and below the moldy area. Keep your knife or instrument out of the mold itself. The remaining cheese will be safe and flavorful to eat. Do NOT try to save individual cheese slices, soft cheese, cottage cheese, cream, sour cream or yogurt when mold appears.

DAIRY FOOD

➢ Most dairy foods such as milk, yogurt,

sour cream and cottage cheese have freshness dates on their cartons for appropriate length of storage. Store these foods in the original carton and refrigerate immediately after purchasing and after each use.

Frozen food storage

➢ The freezer compartment of a refriger-

ator should be kept at approximately 0° F. To check the temperature, place an appliance thermometer between the frozen packages and check after 24 hours. If the temperature is above 0˚ F, adjust the control as described on page 8.

➢ A freezer operates more efficiently

when it is at least two-thirds full.

PACKAGING FOODS FOR FREEZING

➢ To minimize dehydration and quality

deterioration use aluminum foil, freezer wrap, freezer bags or airtight containers. Force as much air out of the packages as possible and be sure they are tightly sealed. Trapped air can cause the food to dry out, change color and develop an off-flavor (freezer burn).

➢ Overwrap fresh meats and poultry

with suitable freezer wrap prior to freezing.

➢ Do not refreeze meat that has com-

pletely thawed.

LOADING THE FREEZER

➢ Avoid adding too much warm food to

the freezer at one time. This overloads the freezer, slows the rate of freezing and can raise the temperature of frozen foods.

➢ Leave space between the packages so

cold air can circulate freely, allowing food to freeze as quickly as possible.

➢ Avoid storing hard-to-freeze foods

such as ice cream and orange juice on the freezer door shelves. These foods are best stored in the freezer interior where the temperature varies less with door openings.

Refer to the Food Storage Chart on page 13 for approximate storage times.

FOOD STORAGE CHART

(Storage times are approximate and may vary depending on type of packaging, storage temperature, and the quality of the food when purchased.)

Foods

Butter Milk & cream

Cream cheese, cheese spread & cheese food

Cottage cheese Sour cream

Hard cheese (Swiss, Cheddar & Parmesan)

Eggs in the shell Leftover yolks or whites

Apples Bananas Pears, plums, avocados Berries, cherries, apricots Grapes Citrus fruits Pineapples, cut

Asparagus Brussels sprouts, broccoli, cau-

liflower, green peas, lima beans, onions, peppers

Cabbage, celery Carrots, parsnips, beets, &

turnips Lettuce

Chicken and Turkey, whole Chicken and Turkey, pieces Fish

Bacon Beef or lamb, ground

Beef or lamb, roast & steak Ham, fully cooked, whole

half slices

Luncheon meat Pork, roast Pork, chops Sausage, ground Sausage, smoked Veal Frankfurters

Refrigerator

1 month 1 week

1-2 weeks

3-5 days 10 days

1-2 months

3 weeks 2-4 days

1 month 2-4 days 3-4 days 2-3 days 3-5 days 1-2 weeks 2-3 days

1-2 days 3-5 days

1-2 weeks 7-10 days

7-10 days

1-2 days 1-2 days 1-2 days

7 days 1-2 days

3-5 days 7 days

5 days 3 days

3-5 days 3-5 days 3-5 days 1-2 days 7 days 3-5 days 7 days

Freezer

6-9 months Not recommended

Not recommended

4-6 months May become crumbly

Not recommended 9-12 months

8 months (cooked) 6 months (whole/peeled) Not recommended 6 months 1 month (whole) Not recommended 6-12 months

8-10 months 8-10 months

Not recommended 8-10 months

Not recommended

12 months 9 months 2-6 months

1 month 3-4 months

6-9 months 1-2 months

1-2 months 1-2 months

1-2 months 4-6 months

4 months 1-2 months 1-2 months 4-6 months

1 month

Storage Tips

Wrap tightly or cover. Check carton date. Close tightly. Don’t return unused portions to

original container. Don’t freeze cream unless whipped. Wrap tightly.

Store in original carton. Check carton date.

Wrap tightly. Cut off any mold.

Refrigerate small ends down. For each cup of yolks to be frozen, add 1 tsp. sugar for use in sweet, or 1 tsp. salt for non-sweet dishes.

May also store unripe or hard apples at 60-70° F. Ripen at room temperature before refrigerating. Bananas and

avocados darken when refrigerated.

May also store at 60-70° F. If refrigerated, store uncovered. Will not ripen after purchase. Use quickly.

Do not wash before refrigerating. Store in crisper. Wrap odorous foods. Leave peas in pods.

Wrap odorous foods & refrigerate in crisper. Remove tops. Wrap odorous foods and refrigerate in the crisper.

Keep in original packaging for refrigeration. Place in the Meat and Cheese Drawer. When freezing longer than 2 weeks, overwrap with freezer wrap.

Fresh meats can be kept in original packaging for refrigeration. Place in the Meat and Cheese Drawer. When freezing longer than 2 weeks, overwrap with freezer wrap.

Unopened, vacuum-packed luncheon meat may be kept up to 2 weeks in the Meat and Cheese Drawer.

Processed meats should be tightly wrapped and stored in the Meat and Cheese Drawer.

EGGS

FRUITS

DAIRY PRODUCTS

Sources: United States Department of Agriculture; Food Marketing Institute; Cooperative Extension Service, Iowa State University

VEGETABLES

MEATS

POULTRY & FISH

FOOD STORAGE TIPS

,CONT.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

storing the refrigerator

STORING THE REFRIGERATOR

Vac ati o ns

If you will be gone for a month or less, leave the controls at the usual settings.

During longer absences:

1. Remove all food.

2. Shut off the ice maker (if installed) and the valve where you tapped into the water line to supply the refrigerator.

3. Disconnect the refrigerator from the electrical outlet.

4. Clean and dry the refrigerator thoroughly.

5. Leave the doors open to prevent odors.

Moving

When moving, follow steps 1–4 under Vacations. In addition, remove and carefully pack any items that are easily removable. Ship the refrigerator in an upright position with the doors taped shut.

CARE AND CLEANING

Refer to the chart on the following page for specific refrigerator cleaning guidelines.

REPLACING A LIGHT BULB

REFRIGERATOR

➢ Slide shield

toward back of compartment to release from light assembly.

➢ Remove light bulbs. ➢ Replace with appliance bulbs no

greater than 40 watts.

➢ Replace light bulb cover by inserting

tabs on light shield into liner holes on each side of light assembly. Slide shield toward front of unit until it locks into place. DO NOT force shield beyond locking point. Doing so may damage light shield.

FREEZER

➢ Pinch rear tabs on light cover and pull

straight down.

➢ Remove light bulb. ➢ Replace bulb with appliance bulb no

greater than 40 watts.

➢ Insert front tabs of light cover into

refrigerator liner and snap rear portion over light assembly.

CONDENSER

Energy saving tips

➢ When placing refrigerator into final

position, allow for

⁄2

" clearance around the top and sides of unit to supply ample ventilation.

➢ Locate the refrigerator away from heat

producing appliances such as the range or dishwasher, heat vents and direct sunlight.

➢ Level the refrigerator and do not block

ventilation around the front grille.

➢ Keep the freezer full to near capacity

so less cold air will escape during door openings. When the freezer is less than two-thirds full, place milk cartons half full of water in the freezer.

➢ Let hot dishes cool slightly before put-

ting into the refrigerator or freezer.

➢ Cover liquids. ➢ Wipe moisture from the outside of

containers before placing them into the refrigerator.

➢ Avoid opening the doors too often. ➢ Clean condenser coils every 3 months. ➢ Do not use aluminum foil, wax paper

or paper toweling as shelf liners. This decreases air flow and causes unit to run less efficiently.

Cleaning of the condenser is recommended every three months.

➢ Unplug the refrigerator. ➢ Remove the toe grille (see page 2) to

access the condenser coils.

➢ Using a vacuum cleaner hose, remove

the dust and soil.

➢ Use a vacuum cleaner hose with the

brush attachment to clean the condenser fan outlet grille at the back of the refrigerator.

Disconnect the power cord or disconnect the circuit breaker before cleaning.

CAUTION

Disconnect the power cord or disconnect the circuit breaker before replacing light bulb(s). Wear gloves as protection against broken glass.

CAUTION

Disconnect the power cord or disconnect the circuit breaker before cleaning the condenser.

CAUTION

PART DO

➢ Use 4 tablespoons (60 milliliters) of baking soda dissolved in

1 quart (1 liter) warm soapy water.

➢ Rinse surfaces with clean warm water and dry immediately to

avoid water spots.

➢ Use warm, soapy water and a soft, clean cloth or sponge. ➢ Rinse surfaces with clean warm water and dry immediately to

avoid water spots.

➢ After cleaning, rinse and dry. To restore luster and remove

streaks follow with Stainless Steel Magic Spray* (Part No.

20000008).

➢ Use a vacuum cleaner hose nozzle.

➢ Use a vacuum cleaner hose nozzle with brush attachment.

➢ Follow removal and installation instructions from appropriate

feature section.

➢ Allow items to adjust to room temperature. ➢ Dilute mild detergent and use a soft clean cloth or sponge for

cleaning.

➢ Use a plastic bristle brush to get into crevices. ➢ Rinse surfaces with clean warm water. ➢ Dry glass and clear items immediately to avoid spots.

DO NOT USE

➢ Abrasive or harsh cleaners ➢ Ammonia ➢ Chlorine bleach ➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Abrasive or harsh cleaners ➢ Ammonia ➢ Chlorine bleach ➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Vinegar-based products ➢ Citrus-based cleaners

➢ Abrasive or harsh cleaners ➢ Metal or plastic-textured

scouring pads

➢ A dishwasher

Textured Doors and Exterior

Cabinet Interior

Stainless Steel Doors and Exterior* IMPORTANT: Damage

to stainless steel finish due to improper use of cleaning products or non-recommended products is not covered under this product’s warranty.

Door Gaskets

Condenser Coil

Remove toe grille to access

Condenser Fan Outlet Grille

See back of refrigerator Accessories Shelves,

buckets, drawers, etc.

To avoid personal injury or property damage, observe the following:

➢ Read and follow manufacturer ’s directions for all cleaning products. ➢ DO NOT place buckets, shelves or accessories in dishwasher. Cracking or warp-

ing of accessories may result.

➢ Do not touch refrigerated surfaces with wet or damp hands. Damp objects stick to

cold metal surfaces. Before cleaning the freezer, allow it to warm up. Allow glass shelves to warm up before immersing in warm water.

CAUTION

To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before cleaning. After cleaning, connect power.

WARNING

* Cleaner is available for order through your manufacturer. Please contact them, using the information on the front cover of your

User’s Guide, for further ordering information.

Refrigerator Cleaning Chart

CARE & CLEANING

,CONT.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

care & cleaning

Removing odors from refrigerator

➢ Remove all food. ➢ Disconnect refrigerator. ➢ Clean the following items using the

appropriate instructions in the Care and Cleaning section.

–Walls, floor and ceiling of cabinet

interior.

– Drawers, shelves and gaskets

according to the instructions in this section.

➢ Pay special attention to clean all

crevices by completing the following steps:

– Dilute mild detergent and brush

solution into crevices using a plas-

tic bristle brush. – Let stand for 5 minutes. – Rinse surfaces with warm water.

Dry surfaces with a soft, clean

cloth.

➢ Wash and dry all bottles, containers

and jars. Discard spoiled or expired items.

➢ Wrap or store odor-causing foods in

tightly-sealed containers to prevent reoccurring odors.

➢ Connect power to refrigerator and

return food to unit.

➢ After 24 hours, check if odor has been

eliminated.

If odor is still present:

➢ Remove drawers and place on top

shelf of refrigerator.

➢ Pack refrigerator and freezer sections

– including doors – with crumpled sheets of black and white newspaper.

➢ Place charcoal briquettes randomly on

crumpled newspaper in both freezer and refrigerator compartments.

➢ Close doors and let stand 24-48

hours.

NORMAL OPERATING SOUNDS

Improvements in refrigeration design may produce sounds in your new refrigerator that are different or were not present in an older model. These improvements were made to create a refrigerator that is better at preserving food, more energy efficient, and quieter overall. Because new refrigerators run quieter, sounds may be detected that were present in older refrigerators, but were masked by higher sound levels. Many of these sounds are normal. Please note that the surfaces adjacent to a refrigerator, such as hard walls, floors and cabinetry may make these sounds seem even louder. The following are some of the normal sounds that may be noticed in a new refrigerator.

SOLUTION

➢ Normal operation

➢ See Installation Instructions for details on how to level

your refrigerator.

➢ Normal operation

➢ Stop sound by raising ice maker arm to ‘off’ position. See

Automatic Ice Maker section on page 11 for details.

➢ Normal operation

POSSIBLE CAUSE

➢ Freezer control (A) clicks when

starting or stopping compressor.

➢ Defrost timer (B) sounds like an

electric clock and snaps in and out of defrost cycle.

➢ Freezer fan (C) and condenser

fan (D) make this noise while operating.

➢ Evaporator (E) and heat

exchanger (F) refrigerant makes this noise when flowing.

➢ Ice cubes from ice maker (some

models) drop into ice bucket (G).

➢ Compressor (H) makes a pul-

sating sound while running.

➢ Refrigerator is not level.

➢ Ice maker water valve (I)

hookup (some models) buzzes when ice maker fills with water.

➢ Ice maker (J) is in the ‘on’ posi-

tion without water connection.

➢ Compressor (H) can make a high

pitched hum while operating.

➢ Defrost heater (K) hisses,

sizzles, or pops when operating.

TOPIC

Clicking

Air rushing or whirring

Gurgling or boiling sound

Thumping

Vibrating noise

Buzzing

Humming

Hissing or popping

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

operating sounds

BEFORE YOU CALL FOR SERVICE

PROBLEM POSSIBLE CAUSES WHAT TO DO Freezer control and lights Refrigerator is in defrost mode. Normal operation. Wait 40 minutes to see if refrigerator restarts.

are on, but compressor is not operating

Refrigerator does not Refrigerator is not plugged in. Plug in unit. operate

Freezer control is not on. See page 8. Fuse is blown, or circuit breaker needs Replace blown fuses. Reset circuit breaker.

to be reset. Power outage has occurred Call local power company listing to report outage.

Refrigerator still won’t Unit is malfunctioning. Unplug refrigerator and transfer food to another refrigerator. If operate another unit is not available, place dry ice in freezer section to

preserve food. Warranty does not cover food loss. Contact service for assistance.

Refrigerator has an odor Compartment is dirty or has odor-causing See page 16.

food.

Crisper drawers do not Contents of drawer, or positioning of items Reposition food items and containers. close freely in the surrounding compartment could be

obstructing drawer. Drawer is not in proper position. See page 9 for proper crisper placement. Refrigerator is not level. See page 2. Drawer channels are dirty or need Clean drawer channels with warm, soapy water. Rinse and dry.

treatment.

Apply a thin layer of petroleum jelly to drawer channels.

Refrigerator runs too Doors have been opened frequently or Minimize door openings. frequently for long periods of time.

Humidity or heat in surrounding area is Normal operation. high.

Food has recently been added. Allow time for recently added food to reach refrigerator or

freezer temperature.

Refrigerator is exposed to heat by Evaluate your refrigerator’s environment. Refrigerator may environment or by appliances nearby. need to be moved to run more efficiently.

Condenser coils are dirty. Clean according to cleaning instructions. See page 14. Controls need to be adjusted. See page 8. Door is not closing properly. Refrigerator is not level. See page 2. Today’s refrigerators start and stop more Check gaskets for proper seal. Clean, if necessary. See page 15.

often to maintain even temperatures.

Check to see if something is preventing door from closing.

Noise, sounds and Normal operation. See page 17. vibrations

Cabinet not level. Level cabinet. See page 2.

Food temperature Condenser coils are dirty. Clean according to cleaning instructions. See page 14. is too cold

Refrigerator or freezer controls are set See page 8. too high.

Food temperature Door is not closing properly. Refrigerator is not level. See page 2. is too warm

Check gaskets for proper seal. Clean, if necessary. See page 15.

Check to see if something is preventing door from closing. Controls need to be adjusted. See page 8. Condenser coils are dirty. Clean according to cleaning instructions. See page 14. Rear air grille is blocked. Check the positioning of food items in refrigerator to make sure

grille is not blocked. Rear air grilles are located under crisper

drawers. Prolonged door openings. Minimize door openings.

Review this chart of troubleshooting tips first…you may not need to call for service at all.

GENERAL OPERATION

NOISE

TEMPERATURE

PROBLEM POSSIBLE CAUSES WHAT TO DO Refrigerator is leaking Plastic tubing was used to complete water Use copper tubing for installation. Plastic is less durable and

water connection. can cause leakage. Ice forms in inlet tube to Improper water valve was installed. Check water connection procedure in the Installation

ice maker Instructions. Self-piercing and

⁄16" saddle valves cause low

water pressure and may clog the line over time.

Water pressure is low. Water pressure must be between 20 to 100 pounds per square

inch to function properly.

Water flow is slower than Freezer temperature is too high. See page 8. Freezer temperature should be approximately normal 0° F (-18° C).

Water pressure is low. Water pressure must be between 20 to 100 pounds per square

inch to function properly.

Improper water valve was installed. Check water connection procedure in the Installation

Instructions. Self-piercing and

⁄16" saddle valves cause low

water pressure and may clog the line over time.

Water droplets form on Check gaskets for proper seal. Clean, if necessary. See page 15. outside of refrigerator

Humidity levels are high. Normal during times of high humidity. Controls require adjustment. See page 8.

Water droplets form on Humidity levels are high or door has been Minimize door openings. inside of refrigerator been opened frequently.

Check gaskets for proper seal. Clean, if necessary. See page 15.

ICEMOISTURE

BEFORE YOU CALL FOR SERVICE

, CONT.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

before you call

NOTES

MAYTAG • 403 West Fourth Street North • P.O. Box 39 • Newton, Iowa 50208

Maytag warranty What is not covered by these warranties:

1. Conditions and damages resulting from any of the following: a. Improper installation, delivery, or maintenance. b. Any repair, modification, alteration, or adjustment not authorized by the

manufacturer or an authorized servicer. c. Misuse, abuse, accidents, or unreasonable use. d. Incorrect electric current, voltage, or supply. e. Improper setting of any control.

2. Warranties are void if the original serial numbers have been removed, altered, or cannot be readily determined.

3. Light bulbs.

4. Products purchased for commercial or industrial use.

5. The cost of service or service call to: a. Correct installation errors. b. Instruct the user on the proper use of the product. c. Transport the appliance to the servicer.

6. Consequential or incidental damages sustained by any person as a result of any breach of these warranties. Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above exclusion may not apply.

To purchase accessories or replacement parts not covered by your product warranty:

Please have your model and serial numbers ready and call our parts specialists at 1-877-232-6771 inside U.S.A. from 7 a.m. to 7 p.m. central time Monday through Friday. Outside the U.S.A., contact your local appliance dealer or parts distributor.

If you need service

❚ Call the dealer from whom your appliance was purchased or call Maytag

ServicesSM, Maytag Customer Assistance at 1-800-688-9900, U.S.A. or 1-800-688-2002 Canada to locate an authorized servicer.

❚ Be sure to retain proof of purchase to verify warranty status. Refer to

WARRANTY for further information on owner’s responsibilities for warranty service.

❚ If the dealer or service company cannot resolve the problem, write to

Maytag ServicesSM, Attn: CAIR®Center, P.O. Box 2370, Cleveland, TN 37320-2370, or call 1-800-688-9900 U.S.A. or 1-800-688-2002 Canada.

U.S.A. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

NOTE: When writing or calling about a service problem, please include the following information:

a. Your name, address and telephone number; b. Model number and serial number; c. Name and address of your dealer or servicer; d. Aclear description of the problem you are having; e. Proof of purchase (sales receipt).

❚ User’s guides, service manuals and parts information are available from

Maytag ServicesSM, Maytag Customer Assistance.

Full One Year Warranty

For one (1) year from the date of original retail purchase, any part that fails in normal home use will be repaired or replaced free of charge.

Ice Maker - When purchased with the refrigeration and installed by the dealer the ice maker will be considered part of the refrigerator for warranty purposes.

Limited Warranty - Major Refrigeration Components

Second Through Fifth Year - After the first

year from the date of original purchase, through the fifth year, Maytag Appliances will repair or replace, at its option, free of charge for parts and labor, any part of the sealed refrigeration system (consisting of the compressor, evaporator, condenser, drier and connecting tubing) and the cabinet liner (exclusive of the door liner) which fail in normal home use. Mileage and transportation charges, if required, shall be the responsibility of the owner.

Limited Warranty - Other Parts Second Year - Parts other than major refriger-

ation components which fail in normal home use during the second year following the date of original retail purchase will be repaired or provided free of charge for the part itself, with the owner paying all other costs, including labor, mileage and transportation.

Please note: The full warranty and the limited warranties apply when the refrigerator is located in the United States or Canada. Refrigerators located elsewhere are covered by the limited warranties only including parts that fail during the first year.

Limitations of Liability

The warrantor shall not be liable for any incidental or consequential damages, including food loss. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation or exclusion may not apply to you.

The specific warranties expressed above are the ONLY warranties provided by the manufac- turer. These warranties give you specific legal rights, and you may also have other rights which vary from state to state.

+ 50 hidden pages