Maytag MAV408DAWW, MAV3955EWW, MAV4755AWW, MAVT346AWW, MAV3855AWW User Manual

...

MAV-1

Use & Care Guide

Table of Contents

Important Safety Instructions 1-2

Operating Tips . . . . . . . . . . . 3-4

Using the Controls

3 Speed Select Models . . . . . . . 5-6

4 Speed Select Models . . . . . . . 7-8

Electronic Control Models . . . . . .9-11

Special Features . . . . . . . . 12-13

Care & Cleaning . . . . . . . . . . . 13

Troubleshooting . . . . . . . . . . . 14

Service & W

Guide d’utilisation

et d’entretien . . . . . . . . . . . . . . 16

Guía de uso y cuidado . . . . . 34

arranty . . . . . . . . 15

orm No. A/0

6/05 P

art No. 6 2621

Important Safety Instructions

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this guide for future reference. Keep sales receipt and/or canceled check as proof of purchase.

Model Number _______________________________

Serial Number ________________________________

Date of Purchase______________________________

If you have questions, call: Maytag Customer Assistance

1-800-688-9900 U.S.A. 1-800-688-2002 Canada (Mon.-Fri., 8am-8pm Eastern Time) Internet: http://www.maytag.com

U.S. Customers using TTY for deaf, hearing impaired or speech impaired, call 1-8

In our continuing effort to improve the quality and performance of our appliances, it may be necessary to make changes to the appliance without revising this guide.

For service information, see page 15.

00-688-2080.

What You Need to Know About Safety Instructions

Warning and Important Safety Instructions appearing in this guide are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when

alling, maint

inst Always contact the manufacturer about problems or

conditions you do not underst

Recognize Safety Symbols, Words, Labels

WARNING – Hazards or unsafe practices which COULD

result in severe personal injury or death.

aining or operating appliance.

and.

WARNING

WARNING! FIRE HAZARD

Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

Do not wash articles which have been previously cleaned, washed, soaked, or spotted with gasoline, dry-cleaning solvents, oil, waxes, chemical solvents, alcohol, turpentine, or other flammable or explosive materials. These substances will be retained in articles, and articles which still contain these flammable or explosive substances give off vapors that could ignite or explode.

Observe these precautions when using cleaning fluids, spot or stain removers, etc. These products should be labeled “nonflammable.” Use according to manufacturers directions in a well ventilated area or outdoors. Thoroughly rinse articles by hand before placing them in the washer – rust removers for example – will damage components and the finish of the washer.

Keep area around and underneath washer free from the accumulation of combustible materials, such as lint, paper, rags, gasoline, and all other flammable vapors and liquids.

ROGEN GAS IS EXPLOSIVE!

HYD

conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. If the hot water system has not been used for such a period, before using the washer, turn on all the hot water faucets and let the water flow from each faucet for several minute accumulated hydrogen gas. As this gas is flammable, do not smoke or use an open flame during this time.

Recent studies have shown that if vegetable oil contaminated materials are incompletely washed, a

arry-over and buildup of the oil may contribute to a

c chemical reaction (spontaneous combustion) that could c be more likely to happen if the load were left in the dryer after tumbling stopped or if items were folded and st

ause a load to c

acked while warm.

. Some of the

his will release any

s. T

atch fire by it

se products

Under cer

his would

. T

self

tain

CAUTION

CAUTION – Hazards or unsafe practices which COULD result in minor personal injury.

Important Safety Instructions

WARNING

To reduce the risk of fire, explosion, electric shock, or personal injury when using your washer, follow basic safety precautions, including the following:

1. Read all instructions before using the appliance.

2. As with any equipment using electricity and having moving parts, there are potential hazards. To use this appliance safely, the operator should become familiar with the instructions for operation of the appliance and always exercise care when using it.

Do not install or store this appliance where it will be exposed to the weather.

4. Install and level washer on a floor that can support the weight.

5. This appliance must be properly grounded. Never plug the appliance cord into a receptacle which is not grounded adequately and in accordance with local and national codes. See installation instructions for grounding this appliance.

6. To avoid the possibility of fire or explosion: a.

Do not wash items that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode. Hand wash and line dry any items containing these substances.

Any material on which you have used a cleaning solvent, or which is saturated with flammable liquids or solids, should not be placed in the washer until all traces of these liquids or solids and their fumes have been removed.

These items include acetone, denatured alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers, turpentine, waxes and wax removers.

Do not add gasoline, dry-cleaning solvents, or

other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

ain conditions, hydrogen gas may be

Under cer

produced in a hot water system that has not been used for two weeks or more. HYD

XPLOSIVE. If the hot water system has not been

E used for such a period, before using a washing machine or combination washer-dryer hot water faucets and let the water flow from each for several minute

AS IS

N G

, turn on all

his will release any

s. T

accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

d. Do not wash or dry items that are soiled with

vegetable or cooking oil. These items may contain some oil after laundering. Due to the remaining oil, the fabric may smoke or catch fire by itself.

7. Do not reach into the appliance if the tub or agitator

is moving. Do not allow children or pets to play on, in, or in

8. front of the appliance. Close supervision is necessary when the appliance is used near children and pets.

Do not tamper with controls. Do not repair or replace any part of the appliance or

10. attempt any servicing unless specifically recommended in published user-repair instructions that you understand and have the skills to carry out.

11. Unplug power supply cord before attempting to service your washer. Service is to be done only by qualified service personnel.

12. The agit removed, it must be replaced by pushing down completely and the locking screw tightened before the washer is operated.

13. Keep all laundry aids such as detergents, bleach, etc., out of the reach of children, preferably in a locked cabinet. Use laundry aids only as directed by the manufacturer. Observe all warnings on container labels.

14. Keep the area around and underneath washer free from the accumulation of combustible materials, such as lint, paper, rags, gasoline, and all other flammable vapors and liquids.

15.

Do not use chlorine bleach and ammonia or acids (such as vinegar or rust remover) in the s Hazardous fumes can form.

16. Do not machine wash fiberglass materials. Small particles can stick to fabrics washed in following loads and c

17. For flame resistant finishes - follow garment manufacturer's instructions carefully. Improper laundering could remove the finish.

18. Before the appliance is removed from service or disc

19. Inlet hoses are subject to damage and deterioration over time. Check the hoses periodically for bulges, kinks, cuts, wear or leaks and replace them every five years.

ator should not be removed. If the agitator is

ame wash.

ause skin irrit

arded, remove the door to the washing compar

ation.

tment.

SAVE THESE INSTRUCTIONS

Operating Tips

Detergent

• Use either liquid or granular laundry detergent. For best results, be sure detergent is added to the washer BEFORE the load and be sure the wash water is above 60

• Use the correct amount of detergent for the load size, soil level and water conditions. Use more detergent if you have hard water and very soiled loads.

If you have soft water or a lightly soiled load, use less detergent. (See manufacturer’s instructions.)

• Wipe up any detergent spills on the washer.

For best results add the detergent to the washtub

• before adding the load.

• Put dry, unfolded clothes loosely in the tub, up to the top row of holes for a maximum load.

•

Do not wrap large items like sheets around the

ator.

agit

• Mix large and small items for best circulation. W bulky items like blankets separately.

• When laundering wrinkle-free items or items of

ate construction, washable woolens or loosely

delic knit items, never use le level setting. This will minimize shrinkage, wrinkling and pulling of seams.

Close lid c

•

arefully to avoid slamming.

ss than the MEDIUM water

ash

Operating Tips

Additional Tips

• During the spin, it is possible for the load to become unevenly distributed in the tub. If this happens, push in the control dial, open the lid, redistribute the load, close the lid and restart the washer. The spin will resume at the point it was interrupted.

• The washer will pause briefly throughout each cycle. These pauses are normal.

• This washer is designed so that it spin when the lid is open. It will, however, fill with the lid open so water is available for pretreating stains or diluting fabric softener.

• If you open the lid during a spin cycle, the washer will stop. When the lid is closed and the washer is restarted, the washer will continue the cycle at the point it was interrupted.

will not agitate or

Using the Controls – 3 Speed Select Models

STEP 1

Select Water Level

Determine the selected setting based on clothes load size. Selection should provide sufficient water to permit clothes to circulate freely during agitation.

It may become necessary, due to bulky fabrics, to adjust the water level after agitation begins. To adjust the water level, turn the control to to the desired setting.

WATER LEVEL SETTING LOAD SIZE

reset and then back

Mini

Small 1/4 - 1/3

Medium 1/3 – 1/2

Large 1/2 – 2/3

Super 3/4 – Full

Note: Items must circulate freely for best re

1/4 Full

sults.

STEP 2

Select Wash/Rinse Temperature

Your washer gives you a choice of hot, warm or cold water for washing and cold or warm water (select models) for rinsing. Use the char

/RINSE LOAD TYPE

TEMPS

Hot/Cold

arm/W

(select models)

arm/Cold

Cold/Cold

arm

White and heavily soiled, color-fast items.

Moderately soiled, colored items.

Moderately soiled, colored items; most wrinkle-free items.

Brightly colored, lightly soiled items; washable woolens.

t below as a guide.

Automatic Temperature Control (A.T.C.) (select models) provide

temperature Automatic Temperature Control will regulate wash water temperatures by mixing hot and cold water to reach the proper water temperature.

WASH/RINSE LOAD TYPE

TEMPS

ATC Hot/Cold,

ATC Warm/Cold ATC Warm/Warm

(select models) at lower temperatures.

TC Cold/Cold

s for cleaning. To save energy

These settings feature Automatic

Temperature Control:

Save to the hot water from your water heater. Provides optimum cleaning

May add hot water to the incoming cold water as the washer fills. This assure enough to properly activate detergent.

s the optimal wash water

, the

s energy by adding cold water

s that the water will be warm

Note: In wash water temperatures below 60

detergent labels define cold water as up to 85°F.

do not dissolve well or clean well. Care

ontrol features vary by model.

STEP 3

Select Cycle

To select a cycle, push the control dial in (off position) and turn it to the right (clockwise) until the pointer is at the soil level needed for the wash load in the Regular, Wrinkle Control or Delicates cycles.

Regular Cycle

Provides normal agitation and normal spin speeds to wash cottons and heavily soiled items. For maximum cleaning, set the dial at Extra Heavy.

Wrinkle Control Cycle

Provides normal agitation and slow spin speed to protect wrinkle control fabrics.

Delicates Cycle

s slow agitation speed and slow spin speed for

rovide

P delicates and knits.

STEP 4

Select Options (if desired)

Extra Rinse

When the switch is in the On position, an additional rinse at the end of the Regular, Wrinkle Control and Delicates cycles is provided to more completely remove laundry additives, suds, perfumes, etc.

End of Cycle Signal (select models)

he End of Cycle Signal will sound once the c

T completed. The End of Cycle Signal can be canceled by setting the switch to

Off.

ycle is

STEP 5

Pull Control Dial Out to Start

ou may stop the washer at any time by simply

Y pushing the control dial in. Therefore, it is possible to obtain a non-agitated soak or to shorten, skip or repeat any par pushed

in (off position) when you change the setting.

t of a c

ycle. The control dial must be

Note: Do not attempt to turn the control dial

counterclockwise. Damage to the timer will result.

Using the Controls – 4 Speed Select Models

STEP 1

Select Water Level

Determine the selected setting based on clothes load size. Selection should provide sufficient water to permit clothes to circulate freely during agitation. On select models, the Infinite Water Level control allows you to select a specific setting or anywhere in between.

It may become necessary, due to bulky fabrics, to adjust the water level after agitation begins. To adjust the water level, turn the control to to the desired setting.

WATER LEVEL SETTING LOAD SIZE

Mini

Small 1/4 - 1/3

Medium 1/3 – 1/2

Large 1/2 – 2/3

Super 3/4 – Full

Note: Items must circulate freely for best results.

STEP 2

Select Wash/Rinse Temperature

reset and then back

4 Full

WASH/RINSE LOAD TYPE

MPS

These settings feature Automatic

Temperature Control:

ATC Hot/Cold,

ATC Warm/Cold

ATC Warm/Warm

ATC Cold/Cold

Saves energy by adding cold water to the hot water from your water heater. Provides optimum cleaning at lower temperatures.

May add hot water to the incoming cold water as the washer fills. This assures that the water will be warm enough to properly activate detergent.

Your washer gives you a choice of hot, warm or cold water for washing and cold or warm water (select models) for rinsing.

RINSE LOAD TYPE

TEMPS

Hot/Cold

Warm/Warm Moderately soiled, colored items.

(select models)

Warm/Cold

Cold/Cold

Automatic Temperature Control (A.T.C.) (select models) provides the optimal wash water temperature

for cleaning. T wash water temperatures by mixing hot and cold water to reach the proper water temperature.

White and heavily soiled, color-fast items.

Moderately soiled, colored items; most wrinkle-free items.

Brightly colored, lightly soiled items; washable woolens.

ave energy

o s

, this washer will regulate

STEP 3

Select Wash/Spin Speed

our washer has select

Y combinations.

WASH/SPIN LOAD TYPE

PEED

Regular

Normal/Fast

Wrinkle Control

Normal/Slow

Delicate

Gentle/Slow

Handw

Ex. Gentle/Slow

ash

Note: In wash water temperatures below 60

detergents

do not dissolve well or clean well.

able wash and spin speed

Sturdy fabrics needing maximum water extraction like jeans, towels and bedding

Sturdy fabrics needing a slower spin speed to reduce wrinkling, such as

s and dress pants

ss shir

dre Delicate fabrics needing slower spin

speed because of clothing construction

Intermittent slow agitation and soak to gently wash the most delic

ate

items

STEP 4

STEP 5

Select Cycle

To select a cycle, push the control dial in (off position) and turn it to the right (clockwise) until the pointer is at the soil level needed for the wash load.

Important: For optimum fabric care, the appropriate wash and spin speed for the load type must be selected using the wash/spin speed knob.

Regular Cycle

ycle provide

This c Select the

Regular Wash/Spin Speed setting.

s up to 16 minutes of agit

Wrinkle Control

his cycle is designed for sturdy fabrics needing a

T slower spin speed to reduce wrinkling, such as dress shirts and dress pants. Select the

ash/Spin Speed

setting.

Wrinkle Control

Delicates Cycle

ates is designed for items requiring delicate wash

Delic action. Select the setting.

When washing delicate fabrics labeled hand wash, select the setting provides intermittent slow agitation and soak with a slow spin.

Handwash Wash/Spin Speed setting. This

Delicates Wash/Spin Speed

ation.

Select Options (if desired)

Extra Rinse

When the knob is in the On position, an additional rinse at the end of the Regular Delicates cycles is provided to more completely remove laundry additives, suds, perfumes, etc.

, Wrinkle Control and

End of Cycle Signal (select models)

The end of cycle signal will sound once the cycle is completed. The end of cycle signal can be canceled by setting the switch to Off.

STEP 6

Pull Control Dial Out to Start

You may stop the washer at any time by simply pushing the control dial in. Therefore it is possible to

ain a non-agit

obt repeat any part of a cycle. The control dial must be pushed

in (off position) when you change the setting.

ated soak or to shor

Note: Do not attempt to turn the control dial

counterclockwise. Damage to the timer will result.

ten, skip or

Soak Only (select models)

Provides 4 minutes of agitation, then soak. Avoid

0 minutes or less.

extended soaking – soak f

The control dial must be manually advanced to a spin setting to spin and drain the water.

or 3

Using the Controls – Electronic Control Models

Getting Started

1. Add detergent and additives to the washer.

2. Load the washer.

3. Close the lid.

4. Select the appropriate cycle and options for the load.

5. Press the

6. The Fill indicator light will illuminate and the washer will start to fill.

Note: The lid must be completely closed in order

to operate the washer controls.

STEP 1

Select Water Level

Determine the selected setting based on clothes load size. Selection should provide sufficient water to permit clothes to circulate freely during agitation.

It may become necessary, due to bulky fabrics, to adjust the water level after agit the water level, turn the Infinite Water Level control to

reset and then back to the desired setting.

WATER LEVEL SETTING LOAD SIZE

Cycle Selector dial.

ation begins. T

Mini

Small 1/4 - 1/3

1/4 Full

o adjust

WASH/RINSE LOAD TYPE

TEMPS

Hot/Cold White and heavily soiled, color-fast

(select models) items.

Warm/Warm Moderately soiled, colored items.

(select models)

Warm/Cold Moderately soiled, colored items;

(select models) most wrinkle-free items.

Cold/Cold Brightly colored, lightly soiled

items; washable woolens.

Medium 1/3 – 1/2

Large 1/2 – 2/3 Super 3/4 – Full

Note: Items must circulate freely for best results.

STEP 2

Select Wash/Rinse Temperature

our washer give

Y water for washing and cold water or warm water (select models) for rinsing. Use the chart as a guide.

s you a choice of hot, warm or cold

Automatic T

the optimal wash water temperature for cleaning. To

ave energy

s temperatures by mixing hot and cold water to reach the proper water temperature.

H/RINSE LOAD TYPE

TEMPS

These settings feature Automatic Temperature Control:

ATC Hot/Cold,

ATC Warm/Cold A

TC Warm/Warm

(select models) at lower temperatures.

ATC Cold/Cold

emperature Control (A.T.C.)

, this washer will regulate wash water

Saves energy by adding cold water to the hot water from your water heater. Provides optimum cleaning

May add hot water to the incoming cold water as the washer fills. This assures that the water will be warm enough to properly activate detergent.

provide

ontrol features vary by model.

STEP 3

Soil Selection

Your washer has select

SOIL LOAD TYPE

SELECTION

Light Use for cleaning lightly soiled loads.

Normal Use for cleaning moderately soiled

Heavy Use for cleaning heavily soiled loads.

Extra Heavy Use for cleaning stained, heavily

able soil level settings.

loads. T for most loads.

soiled sturdy loads.

his setting will be appropriate

STEP 4

Fabric Selection

Select the appropriate fabric cycle for the type of load by turning the cycle selector dial until the indicator light by the desired fabric selection is illuminated.

WASH/SPIN FABRIC SELECTION

SPEED

Quick Wash For lightly soiled or wrinkled

Gentle/Fast garments needed quickly.

Hand Wash Provides intermittent agitation and

Ex. Gentle/Slow soak. For wool, silk, and other

hand-wash-only fabrics.

Delicates For sheer fabrics, bras and lingerie

Gentle/Slow needing slower agit

speeds bec construction.

rinkle Contr

Medium/Slow fabrics and lightly to normally soiled

Regular For most sturdy fabrics including

Medium/Fast cottons, linens and normally soiled

or “wash and wear” and synthetic

garments needing a slower spin speed to reduce wrinkling.

garment extraction.

ause

s needing maximum water

ation and spin

of clothing

Using the Controls – Electronic Control Models

STEP 5

Soak Only (select models)

Provides approximately 33 minutes of alternating periods of soaking with brief agitation at slow speed.

At the end of the cycle, the Cycle Selector dial must be manually set to a wash cycle or spin cycle to drain the washer. Avoid extended soaking.

Spin Only

Provides a spin to remove more water from the load.

Rinse and Spin

Use for loads that need rinsing only or to add rinseadded fabric softener to a load.

Power Off

To cancel the cycle and turn off the washer, turn the Cycle Selector dial to

Power Off and push the dial in.

STEP 6

Select Options

Extra Rinse

When the knob is in the On position, an additional rinse at the end of all cycles is provided to more completely remove laundry additives, suds, perfumes, etc.

End of Cycle Signal

The end of cycle signal will sound once the cycle is completed. On select models, the end of cycle signal can be canceled by setting the switch to Off.

STEP 7

Start the Washer

To start the washer, press the cycle selector dial.

Changing a Cycle

If an incorrect cy selected:

cle has been accidentally

1. Press the cycle selector dial.

2. Turn the

3. Set the desired options for the cycle.

4. Press the cycle selector dial. The Wash indicator

lights stop flashing and the new cycle starts.

cycle selector dial to the desired cycle.

Canceling a Cycle

To cancel a cycle:

ss the

2. Turn the cycle selector dial to

the dial in.

To drain the washer:

1. Select the Rinse and Spin or Spin Only cycle.

2. Press the illuminates and the washer starts the rinse or spin.

cle selector

cycle selector dial. The Spin light

dial

Power Off and push

Special Features

Liquid Bleach Dispenser

The dispenser automatically dilutes liquid chlorine bleach before it reaches your wash load.

To use, follow these steps:

1. Measure liquid chlorine bleach carefully, following the instructions on the bottle.

Pour liquid chlorine bleach into bleach dispenser before adding the load. Avoid splashing

or over-filling the dispenser.

Fabric Softener Dispenser

The dispenser automatically releases liquid fabric softener at the proper time during the cycle.

To use, follow these steps:

1. Pour a measured amount of fabric softener into the dispenser to fill line only.

2. If fabric softener comes below line, add warm water.

If it is necessary to clean the dispenser:

1. Pull the dispenser off of the top of the agitator.

2. Soak for one hour in sink or container in hot water and dishwashing liquid.

3. Hold hands over top and bottom of dispenser and shake to loosen buildup.

4. Rinse with clean, hot water.

5. Repeat process if necessary.

6. Replace dispenser on agitator.

Do not use dishwashing liquid inside the washer. Oversudsing

can occur.

Notes:

• Never pour undiluted liquid chlorine bleach directly onto the load or into the wash tub. It is a powerful chemical and can cause fabric damage, such as tearing or color loss, if not used properly

• If you prefer to use color-safe, non-chlorine bleach, pour it into the wash tub with your detergent. the bleach dispenser.

Do not pour non-chlorine bleaches into

Finger Faucet (select models)

Provides a flow of water when holding the switch in the

On position.

Automatic Lint Filtering System

The Lint Filtering System does not require cleaning.

Wash and rinse water is filtered and re-filtered continuously to trap lint shed by most fabrics during the agitation cycle before it can be redeposited on the wash load. The engineered hole design on the wash basket in conjunction with water flow produced by the agitator, traps lint away from the clothes between the inner wash basket and the outer tub. Lint is automatically flushed from the washer during the spin cycle.

Safety Spin

If for any reason you open the washer lid when the washer is in a spin or extract period, the operation will immediately stop. This is for your personal safety. If your washer doe immediately automatically resume.

s not stop, c

hen the lid is closed, the operation will

. W

all your service technician

Special Features

Unbalanced Spin Load Compensator

Your new washer is designed to handle out-of-balance loads without shutting down or interrupting the washing cycle.

For this reason, the cycle will always be completed. If heavier fabrics in such out-of-balance loads should ever contain excessive moisture at the completion of the cycle, redistribute the clothes in the washer and reset the control dial for the final spin period.

Care & Cleaning

1. After washing, leave the lid open until the interior

is dry. Check hoses to be sure there are no kinks or knots.

3. Your washer should not be installed where

temperatures will go below freezing, as damage to the washer could re

4. To clean, occasionally wipe exterior with a clean

damp sponge or cloth. plastic par

5. Lifetime lubrication is done at the factory, so your

washer never needs to be oiled or greased.

Do not lay heavy or sharp objects on top of your washer.

7. The top of the washer should not be used for

removing stains from garments. Some stain removers, such as rust remover, will mar the finish.

ts.

sult.

Do not use polish on

Overload Protector

A built-in protector automatically shuts off the washer motor in case of an overload. This can occur if:

• The load being washed is too heavy.

• Too many appliances are plugged into the line operating your washer.

• A low voltage condition exists on the line.

• Lid is opened and closed repeatedly.

The overload protector permits the washer to start again when the motor has cooled to a safe operating temperature.

If the motor stops repeatedly, call your service technician.

Cleaning the Interior

Clean the interior of the washer periodically to remove any dir that may remain in the washer as a result of washing clothes. We recommend taking the following steps every 60 to 120 days to clean and freshen your washer interior. The frequenc be cleaned and freshened depends on factors such as usage, the amount of dirt, soil or bacteria being run through your washer to follow these instructions may result in unsatisfactory conditions, including unpleasant odor and/or permanent st

To clean and freshen the washer interior:

1. Add a measured amount of chlorine bleach to the

2. Add 1/4 cup of detergent to the tub.

t, soil, odor

bleach dispenser

, mold, mildew or bacteria residue

y with which the washer should

, or the use of cold water

ains on the washer or washload.

, following package directions.

. Failure

Remove pins, buckles or other sharp objects from

8. clothes to prevent scratching interior parts.

s should not be stored in washer

Clothe

10. Bleach, detergent, solvents, etc. spilled on the top of your washer that are allowed to remain will remove the glossy finish. Remove all spills with a damp, soft cloth.

11. If you close your home for the winter, have a service

. Unplug cord from

technician drain the washer electric

al outlet and disconnect hose

s from faucet

Run the washer without a load through a complete

3. cycle using hot water.

4. Repeat the process if necessary.

Troubleshooting

Won’t Fill

Won’t Agitate

Won’t Spin or Drain

Load is Wet

Stops

• Plug cord into live electrical outlet.

• Check fuse or reset circuit breaker.

• Turn the control dial to proper cycle and restart the washer.

• Turn both faucets on fully.

• Straighten inlet hoses.

• Disconnect hoses and clean screens. Hose filter screens may be plugged.

• Check fuse or reset circuit breaker.

• Make sure the lid is completely closed.

• Turn the control dial to proper cycle and restart the washer.

• Pauses are normal. Wait and see if the washer will start again.

• Check fuse or reset circuit breaker.

• Straighten drain hoses. Eliminate kinked hoses. If there is a home drain restriction, call for drain service.

• Close lid and restart the washer. For your safety, washer will not spin unless the lid is closed.

• Suds lock – caused by too much suds. Rewash without detergent. Use correct amount of a low-sudsing detergent.

• Unevenly distributed load. Redistribute the load, close the lid and restart the washer. Check for leveling. Be sure water level is acceptable for load size.

• A normal spin speed is recommended for heavy loads like jeans or towels.

• Plug cord into live electrical outlet.

• Check fuse or reset circuit breaker.

• Close lid and restart the washer. For your safety, washer will not agitate or spin unless lid is closed.

• This may be a pause in the cycle. Wait briefly and it may start.

Leaks Water

Is Noisy

Fills with the Wrong Temperature Water

e Selector

Cycl Advances Through Off

• Make sure hose connections are tight.

• Make sure end of drain hose is correctly inserted and secured to drain facility.

• Avoid extended soaking – soak for 30 minutes or less.

• Avoid overloading.

• Be sure washer is leveled properly as outlined in installation manual.

• Weak floors can cause vibration and walking.

• Operating sounds will vary depending on agitation speed.

on fully

urn both faucet

•

If equipped with a temperature selector dial, be sure it is set directly on a temperature setting and

• not between settings.

• Make sure temperature selection is correct.

• While the washer is filling, you may notice just hot and/or just cold water entering the tub when cold or warm wash temperatures are selected. This is a normal function of the Automatic

emperature Control (select models) feature as the washer determine

T the water.

• If Auto Temperature Control (select models) is selected, cold water may feel warmer than cold water from the tap.

• Make sure hoses are connected to correct faucets and inlet connections. Be sure water supply is regulated correctly. Flush water line before filling washer

Check the water heater

• Also check water heater capacity and recovery rate.

• Disconnect hoses and clean screens. Hose filter screens may be plugged.

•

Extra Rinse (select models) is selected.

s the temperature of

. It should be set to deliver a minimum 120° F (49° C) hot water at the tap.

or further assistance, call Maytag Customer A

U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

ssistance toll-free at

1-800-688-9900 USA or 1-800-688-2002 Canada.

Service & Warranty

Washer Warranty

Full One-Year Warranty

or one (1) year from the date of original retail

F purchase, any part which fails in normal home use will be repaired or replaced free of charge.

Limited Warranty

After the first year from date of original retail purchase, through the time periods listed below, the parts designated below which fail in normal home use will be repaired or replaced free of charge for the part itself, with the owner paying all other costs, including labor, mileage, transportation, trip charge and diagnostic charge, if required.

Second Year – All parts. Third Through Fifth Year – All parts of the

transmission assembly.

Third Through Lifetime – The inner wash basket.

Additional Limited Warranty Against RustThrough – Should an exterior cabinet, including

the top and lid, rust through during the one-year period starting from the date of retail purchase, repair or replacement will be made free of charge. After the first and through the fifth year, repair or replacement will be made free of charge for the part itself, with the owner paying all other costs, including labor, mileage, transportation, trip charge and diagnostic charge, if required.

Please Note: This full warranty and the limited warranty apply when the appliance is located in the United States or Canada. Appliances located elsewhere are covered by the limited warranty only, including parts which fail during the first two years.

Canadian Residents

This warranty covers only those appliances installed in Canada that have been listed with the Canadian Standards Association unle brought into Canada due to transfer of residence from the United States to Canada.

The specific warranties expressed above are the ONLY warranties provided by the manufacturer. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

ss the appliance

s are

What is Not Covered By These Warranties:

1. Conditions and damages resulting from any of the following: a. Improper installation, delivery, or maintenance. b. Any repair, modification, alteration, or adjustment not

authorized by the manufacturer or an authorized servicer. c. Misuse, abuse, accidents, unreasonable use, or acts of God. d. Incorrect electric current, voltage, electrical and/or gas

supply. e. Improper setting of any control.

2. Warranties are void if the original serial numbers have been removed, altered or cannot be readily determined.

3. Light Bulbs.

4. Products purchased for commercial or industrial use.

5. The cost of service or service call to: a. Correct installation errors. b. Instruct the user on the proper use of the product. c. Transport the appliance to the servicer and back.

6. Consequential or incidental damages sustained by any person as a result of any breach of these warranties.

Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above exclusion may not apply.

If You Need Service

First see the Troubleshooting section in your Use and Care Guide or call Customer Service at 1-800-688-9900 USA or 1-800-688-2002 Canada.

To Obtain Warranty Service

To locate an authorized service company in your area contact the Maytag dealer from whom your appliance was purchased or call Maytag Services satisfactory warranty service, please call or write:

Maytag Services Attn: CA P.O. Box 2370, Cleveland, TN 37320-2370

U.S.A. 1 Canada 1 U.S. customers using TTY for deaf, hearing impaired or speech impair

Note: W

about a service problem, please include the following:

a. Your name, address and telephone number. b. Model number and serial number (found on the back

center of the control panel) of your appliance.

Name and address of your dealer and the date the

appliance was purchased. d. A clear description of the problem you are having. e. Proof of purchase.

, Customer Assistance. Should you not receive

Center

900

8-9

00-6

-8 8-2002

00-6

-8

00-688-2080.

ed, call 1

hen contacting Maytag Services

-8

, Customer Assist

ance

Use & Care Guides, service manuals and parts information are available from Maytag Services

MAYTAG • 403 W. 4th Street N. • P.O. Box 39 • Newton, Iowa 50208

, Maytag Customer Assistance.

+ 36 hidden pages