Maytag MAH20PRAWW, MAH20PSAWW, MAH20PDCXQ, MAH20PNAWW, MAH20PDAWQ Dimension Guide

Commercial

(28 1/4" includes 3/4"

High Efficiency

hinge (71.8 cm)

Washers

Models
MAH20PD
MAH20PS

44 1/8"*

112.1 cm

MAH20PR
MAH20PN

68.6 cm

PRODUCT SPECIFICATIONS

• Motor: 120 volt, 60 Hz, variable speed, reversible.
Develops 1/4 HP in Wash and 1/2 HP in Spin.

PRODUCT DIMENSIONS

36"*

91.4 cm

41 3/4"
106 cm

27"

* May vary slightly depending on leveling
legs. PN & PR have no coin vault model.
Console height is 43 5/8".

* Add 1/2" to 2" for leveling legs.

• Some export models: in 240 volts, 50 Hz also available.

• Maximum amperage draw: 7 amps (except for motor acceleration surges)

• Export models: 4 amps

• Cycle Time
MAH20PD/PS/PR/PN - Can be custom programmed 31-65 minute cycles.
There is an optional rinse which can vary 4 minutes that would add to these times.

• Water usage (approximately):
18 - 21 gallons (68.1 - 79 liters) based on load size.
5 gallons (18.9 liters) hot water usage per hot wash cycle.

2.5 gallons (9.5 liters) hot water usage per warm wash cycle.
0 gallons (0 liters) hot water usage per cold wash cycle.

2.5 gallons (9.5 liters) hot water usage per cycle. (based on average cycle)

*Note: If optional additional rinse is used add 5 gallons.

• Pressure fill system, not dependent on incoming water pressure or time.

• Weight: Crated (approximately) 225 lbs (102 Kg) Uncrated (approximately) 195 lbs (88 Kg).

• Tub capacity - 2.9 cubic feet. (82.1 liters)

• Diameter x Depth - 21.5" x15" (54.5 cm x 38.1 cm)

• Spin speed: 800 RPM (200 G’s) - Can be programmed to 600, 650, 700 or 800 rpm.

• Spin direction - counter-clockwise (when viewed from the front.)

• Reversible door hinged on left from factory (when viewed from the front.)

• 180° swing door adds 22.25" (56.5 cm) to washer depth at 90°

COMMERCIAL TOP HIGH EFFICENCY WASHERS - MODELS MAH20PD, PN, PR AND PS

2-107/02

WATER CONSUMPTION GALLONS*

CYCLE SELECTION WASH BLEACH RINSE 1 RINSE 2 RINSE 3

TOTAL GALLONS

WHITE HOT 5.0 - - - - 5.0

COLD - .5 5.0 4.5 4.5 14.5 19.5

PERM PRESS HOT 2.5 - - - - 2.5

COLD 2.5 .5 5.0 4.5 4.5 17.0 19.5

COLORS HOT 2.5 - - - - 2.5

COLD 2.5 .5 5.0 4.5 4.5 17.0 19.5

BRIGHT COL. HOT - - - - - 0

COLD 6.5 .5 5.0 4.5 4.5 21.0 21.0

WOOLENS HOT - - - - - 0

COLD 6.5 .5 5.0 4.5 4.5 21.0 21.0
DELICATES HOT - - - - - 0
& KNITS COLD 6.5 .5 5.0 4.5 4.5 21.0 21.0

WATER CONSUMPTION LITERS*

CYCLE SELECTION WASH BLEACH RINSE 1 RINSE 2 RINSE 3

WHITE HOT 19.0 - - - - 19.0

COLD - 1.9 19.0 17.1 17.1 55.0 74.0
PERM PRESS HOT 10.6 - - - - 10.6

COLD 10.6 1.9 19.0 17.1 17.1 64.4 74.0
COLORS HOT 10.6 - - - - 10.6

COLD 10.6 1.9 19.0 17.1 17.1 64.4 74.0
BRIGHT COL. HOT - - - - - 0

COLD 24.6 1.9 19.0 17.1 17.1 79.6 79.6
WOOLENS HOT - - - - - 0

COLD 24.6 1.9 19.0 17.1 17.1 79.6 79.6
DELICATES HOT - - - - - 0
& KNITS COLD 24.6 1.9 19.0 17.1 17.1 79.6 79.6

TOTAL LITERS

*Based on testing with a 8 lb. AHAM load. Water use will vary from 18-21 gallons (68.1 - 79.5
Liters) depending on load size and cycle chosen.

• PD, PS and PR Models are debit card ready.

This Maytag commercial washer is equipped with anti-siphon devices in the form of three
duckbill check valves to prevent water in the washer from re-entering the fresh water supply line.
This antisiphon system is approved by Underwriters Laboratories (U.L.) for this purpose.

ELECTRICAL REQUIREMENTS

• 120 volts, 60 Hz (240 volts, 50 Hz also available for export).

• Uses .10 Kwh per average load.

• Individual branch circuit serving only the washer is recommended.

• Minimum wire size required, awg. 14 (15 amp fuse or breaker), however, we prefer and many

codes will require awg. 12 wire size with a 20 amp fuse or comparable circuit breaker. These
sizes apply to Copper wire only.

• Washer must be grounded in accordance with National Electrical Codes and local codes and

ordinances.

• Appliance is equipped with a power supply cord having a 3-prong (3 conductor) grounding

plug.

COMMERCIAL TOP HIGH EFFICENCY WASHERS - MODELS MAH20PD, PN, PR AND PS

2-207/02

WATER REQUIREMENTS

• Water pressure of 30 to 120 p.s.i. (2.11 - 8.44 Kg/cm2) is recommended.

• Hot water temperature - 120°F. -140°F (49°C.-60°C) recommended.

• 4 foot (1.22 m) length fill hoses provided.

• Access for manual shut-off of water faucets recommended.

• Recommended water pipe size.

MAX. NO. OF WASHERS G.P.M. COPPER PIPE SIZE

141/2" I.D.
4103/4" I.D.

8201" I.D.
14 35 1 1/4" I.D.
20 50 1 1/2" I.D.
40 100 2" I.D.

Note: The water valve on the Maytag commercial washer is rated at 3-10 gpm at 30 to 120 p.s.i. inlet.

The copper pipe sizes shown in the chart are based on rigid copper and should be used as a
minimum recommended guide in a laundry. Any factors relating to pipe size which might affect
water flow to the washers should be discussed and changed in accordance with the
recommendations of your plumbing contractor in compliance with local codes.

DRAIN FACILITY REQUIREMENTS

• Standpipe of 36" (91.4 cm) in height recommended. For standpipes less than 36" (91.4 cm) in
height, route drain hose through clip provided to maintain adequate height.

• Existing drain system must accept 1 1/4" O.D. drain hose. Unit will discharge water at a rate of
about 4.5 gals./minute, with a 36" standpipe or 5.8 gals./minute with a 30" standpipe.

• Drain hose length of 42" (109.7 cm). Bulk drain hose available for extension if needed. Siphon
break accessories are also available.

FLOORING REQUIREMENTS

• Washer must be installed on a well braced, solid floor. (Washer plus load, plus water weighs
approximately 275 lbs. / 124.74 kg)

COMMERCIAL TOP HIGH EFFICENCY WASHERS - MODELS MAH20PD, PN, PR AND PS

2-307/02