MAYTAG HMMR 80220 Daily Reference Guide

DAILY REFERENCE

WWW

GUIDE

You can download the Safety Instructions and the Use and Care Guide by visiting our website docs. whirlpool. eu and following the instructions on the back of this booklet.

Before using the appliance carefully read the Health and Safety guide.

PRODUCT DESCRIPTION

APPLIANCE

1. Worktop

2. Control panel

3. Water tank

4. Door

5. Door handle

6. Door lter (behind door)

7. Bottom lter (behind ap)

8. Adjustable feet (4)

5. 4.

CONTROL PANEL

13.

12.

1. On/O button (Reset if long

pressed)

2. Programme button (Water conductivity setting if long pressed)

3. Cycle end alert

4. Key lock

5. Steam option

6. Knob (Turn to select / Press to

conrm)

7. Start delay

8. Drying time

9. Dryness level

10. Options button

11. Start / Pause button

12. Display

13. Programmes area

2. 7.3. 8.

4. 9.5. 10. 11.6.

FIRST TIME USE

BEFORE USING THE DRYER

CHECK DRAIN HOSE AND WATER TANK

Make sure that the drain hose on the back of the dryer is xed correctly, either to the dryer’s water tank (see picture), or to your domestic sewage system (see Installation guide).

DAILY USE

Make sure that no lighters

WARNING

or matches remain in the laundry.

Also make sure that the water tank is correctly inserted.

See Use and Care Guide for more details on functions / see last page for information on how to obtain the Use and Care Guide

Make sure that the laundry is not soaked with ammable liquids.

1. LOAD LAUNDRY

Prepare your laundry according to the recommendations in section HINTS AND TIPS. Make sure that pockets are empty, fasteners closed and ribbons tied together.

Open the door and load the laundry. Observe the maximum load sizes given in the PROGRAMME CHART.

2. CLOSE DOOR

Make sure that no laundry gets stuck between door glass and door lter.

Close the door so that you can hear it click shut.

3. SWITCH ON DRYER

Press the On/O button « until the programme button lights up. An animation occurs, and there is a sound. Afterwards the dryer is ready to be operated.

4. SET THE DESIRED PROGRAMME

GUIDED MODE – the button light will guide you through

setting your programme in the following order: selection of programme / drying time (ONLY if Drying time or Airing programme is selected) / dryness level (only if selectable / adjustable) / options. As soon as you conrm a selection by pressing the knob, the button light will jump to the next step.

Select programme: Make sure that the Programme button « lights up. Turn the knob to select the desired programme. The indicator next to the selected programme lights up. Conrm the desired programme by pressing the knob.

1 2

Find more information regarding programmes in the

PROGRAMME CHART.

Select Drying time, if needed

Only if you have selected programme Drying time or Airing «, you can set the desired drying time from a minimum of 10 minutes to maximum 180 minutes (three hours). Make sure that the Drying time button lights up.

Turn the knob to select the desired drying time. Conrm it by pressing the knob.

Set dryness level, if needed

If you want to change the dryness level, make sure that the Dryness level button « lights up.

Turn the knob to select the desired dryness level, then press the knob to conrm.

Select options, if needed

If you want to select additional options, make sure that the Options button « lights up. The options which are selectable for your programme are indicated by lighting arrows.

Turn the knob to select the desired options. The symbol of the selected option will blink. To conrm it, press the knob.

Some options / functions can be selected by directly pressing the button.

Refer to section OPTIONS, FUNCTIONS AND

INDICATORS for more information.

INDIVIDUAL MODE

After you have switched on the dryer, you are not forced to follow the GUIDED MODE. It is up to you which order you choose to set your programme. To do a setting, rst press the relevant button, then turn the knob to select, and nally press the knob to conrm. The variety of options and dryness levels depends on the programme selected. Therefore it is recommended to start your setting with selecting the programme.

To change the settings of a running programme or start delay, you can also:

• press Start/Pause to put the running programme on pause

• change your settings

• press Start/Pause again to continue the programme.

7. RESET A RUNNING PROGRAMME, IF NEEDED

Press and hold the On/O button « until “rES” appears on the display.

The programme is ended afterwards. Immediately open the door and unload the laundry, so that eventual heat in the laundry can dissipate.

8. SWITCH OFF THE DRYER AFTER PROGRAMME END

At the end of the programme, „End“ appears on the display. Press On/O « to switch o the dryer. Open the door and take out your laundry.

The dryer will switch o automatically in about a quarter of an hour after programme end, to save energy.

9. EMPTY WATER TANK / CLEAN DOOR FILTER /

CLEAN BOTTOM FILTER Refer to section CARE AND MAINTENANCE.

5. START PROGRAMME

Press and hold Start/Pause « until the button lights up solidly; the drying process starts.

The duration can be recalculated and adapted in the course of the programme. During such phases, an animation occurs on the display.

6. CHANGE THE SETTINGS OF A RUNNING

PROGRAMME, IF NEEDED

You can still change some settings after a programme was started:

• Adjust drying time (only if programme Drying time is selected)

• Add or cancel an option, provided the progress of the programme still allows it. Press the relevant button. The selected setting will blink for a few seconds. While blinking, you can adjust the setting by turning the knob. If the value or setting stopped blinking, press the button again.

Press the knob to conrm the modication. If you do not conrm, the modication will be conrmed automatically — the modied setting will stop blinking. The programme will continue automatically.

+ 5 hidden pages