Maytag FAV6800 User Manual
LEAVE THESE INSTRUCTIONS WITH THE OWNER
LAISSER CES EXPLICATIONS DE MISE EN
SERVICE AU PROPRIÉTAIRE
CERCIÓRESE DE DEJAR ESTAS INSTRUCCIONES
CON EL PROPIETARIO.
Printed in U.S.A. 6 2908990 Rev. B
AUTOMATIC WASHER
INSTALLATION INSTRUCTIONS
MISE EN SERVICE
MACHINE À LAVER
LAVADORA AUTOMÁTICA
INSTRUCCIONES DE INSTALACION
Read this before you start…
PARTS supplied for installation:
Cable tie to secure drain hose to standpipe,
inlet hose or laundry tub
Proper installation is the responsibility of the
purchaser.
SERVICE CALLS PERFORMED AS A RESULT
OF POOR INSTALLATION ARE THE
RESPONSIBILITY OF THE INSTALLER.
Prepare Washer
Step 1
• Remove the carton by cutting only marked areas of the carton. CAUTION: Hoses are connected to the
washer.
NOTE: If the washer is moved without the carton in place, be sure to keep sharp
edges from damaging the washer cabinet or attached hoses.
• Lift the carton up and clear of the washer. Carefully remove any packaging materials from the outside of the washer. NOTE: Retain the corner posts for later use.
• Untape and raise the washer lid, remove the items shipped in the spin basket. Save the
literature for future reference. Close and tape lid.
Step 2
With the lid taped shut, lay corner posts on the floor, as shown. Use one corner
post to support the top, and three posts for the bottom. Gently tip the washer on
its back, laying it across the corner posts.
Step 3
Remove the hex head screw at the
rear of the shipping base. Pull plastic
base away from rear feet, and pull
downward to disengage from front
feet. Recycle or discard the plastic
base. Return washer to upright position. Untape the washer lid.
2 washers and 2 screens for water hoses
Front Feet
Backguard
Remove hex
head screw
Shipping
Base
Carton corner
posts (stacked on
each other)
Corner
Post
TOOLS needed for installation:
• Cutting knife
• Channel lock
• Nut driver
•Level
• Crescent wrench
Page 1
Overall Cabinet Dimensions
Width = 27 1/4" (69.2 cm)
Depth = 29 1/4" (74.3 cm) allow room for hoses.
Height to top of console = 44 3/4" (113.7 cm)
Height to top of open lid = 55 3/4" (141.6 cm)
INSTALL THE WASHER
1. Place the drain hose in the drain facility. To change drain hose direction or prevent
hose from collapsing or becoming damaged, turn the end of the hose while holding the
base of the hose stationary.
Be sure an air-tight connection is NOT made between the drain hose and the standpipe. A Standpipe height of 36” is recommended. Standpipe must also be a minimum
of 1-1/8 in. inside diameter.
NOTE: If drain standpipe is in excess of 5 feet above floor level, a drain
hose extension kit (Part #12001660) will need to be installed.
NOTE: Caution must always be exercised to avoid collapsing or
damaging the drain hose. For best performance the drain hose
should not be restricted in any way, through elbows, coupling's or
excessive lengths.
2. Install one screen strainer and washer on the inside of each fill hose
at the faucet. The dome on the screen strainer must point towards the faucet. See illustration.
3. Thread the inlet hoses with the screen washer to the HOT and COLD faucet connections.
Make sure the hose marked “HOT” is attached to the HOT faucet. Tighten by hand until
snug and then 2/3 of a turn with pliers. Verify hose connections to machine are tight.
DO NOT OVER TIGHTEN.
Turn on “HOT” and “COLD” water supply and check all connections at the water valve
on the machine and at the faucet for leaks.
NOTE: Machine is supplied with 4 feet inlet hoses. Accessory inlet
hoses are available in various lengths up to 10 feet. See accessory parts
section.
4. Plug power cord into a grounded 120 volt 60 Hz approved electrical
service protected by a 15 amp fuse or comparable circuit breaker. This
washer is grounded through the third prong of the power cord when plugged into a
three prong grounded receptacle.
NOTE: NEVER USE AN EXTENSION CORD. NEVER MODIFY WITH AN ADAPTER
THAT MAY ELIMINATE THE GROUND CONNECTION ON THE PLUG. IF A THREE
PRONG GROUND RECEPTACLE IS NOT AVAILABLE, SEE
ADDITIONAL GROUNDING CONNECTIONS SECTION.
5. Slide washer into position.
NOTE: The washer must be leveled on all 4 legs. To properly level a machine,
the top cover and the front panel must be securely fastened. A carpenter’s
level should be used on top cover to level the machine front to back, as shown in illustration.To level
the machine side to side, place level on back edge of the lid as shown in the illustration. It’s a good
idea to check for level again after the first dozen washes and re-level if
necessary.
6. Level washer by turning the leveling legs in or out as necessary. When the
washer is level, tighten the leveling leg lock nuts up against the base of
the washer. This will help prevent the machine from an out of level condition after use. It is preferable to level the machine with the legs only min-
imally extended.
-washer
-screen
Page 2
HOSE
RETAINER
Page 3
Make any corrections necessary to properly complete the installation.
FAV6800
1. Press “Normal” to turn the washer on.
2. Arrow up to select “Hot/Cold” wash-rinse temperature.
3. Press “Start/Pause” to begin the cycle.
4. Allow the Lid to lock and verify that the Lid has
locked.
5. Allow the washer to fill with hot water.
6. Press “Start/Pause” to pause the cycle.
7. Allow the Lid to unlock, lift the Lid and verify the
washer has filled with hot water.
8. Lower the Lid and Press “Off”.
9. Press “Normal”, Press “Bulky Items”
10. Arrow up to select “Cold/Cold” wash-rinse temperature.
11. Press “Start/Pause” to begin the cycle.
12. Allow the washer to fill with cold water.
13. Press “Start/Pause” to pause the cycle.
14. Allow the Lid to unlock, lift the Lid and verify the
washer has filled with cold water.
15. Lower the Lid and press “Off”.
16. Press “Normal”, Press “Spin Only”.
17. Press “Start/Pause” to begin the cycle.
18. Verify the washer spins. This will take several
minutes, the machine will first drain on slow spin
speed.
19. Allow the Spin cycle to finish, verify that the Lid
has unlocked at the end of the cycle.
20. Press “Off”.
FAV9800
1. Press “Home”, select “Set Your Own Cycle”,
select “Cottons”, select “Hot Wash Cold Rinse”.
2. Press “Start/Pause” to begin the cycle.
3. Allow the Lid to lock and verify that the Lid has
locked.
4. Allow the washer to fill with hot water.
5. Press “Start/Pause” to pause the cycle.
6. Allow the Lid to unlock, lift the Lid and verify that
the washer has filled with hot water.
7. Lower the Lid and Press “Off”.
8. Press “Home”, select “Set Your Own Cycle”,
select “Rinse or Spin Only Cycles”, select “Cold
Rinse & Spin”; press “Start/Pause” to begin the
cycle.
9. Allow the washer to fill with cold water.
10. Press “Start/Pause” to pause the cycle.
11. Allow the Lid to unlock, lift the Lid to verify that
the washer has filled with cold water.
12. Lower the Lid and Press “Off”.
13. Press “Home”, select “Set Your Own Cycle”,
select “Rinse or Spin Only Cycles”, select “Spin”.
14. Press “Start/Pause” to begin the cycle.
15. Verify the washer spins. This will take several
minutes, the machine will first drain on slow spin
speed.
16. Allow the Spin cycle to finish, verify that the Lid
has unlocked at the end of the cycle.
17. Select “Ok”.
18. Press “Off”
FINAL INSTALLATION CHECKLIST
■■
Instructions and Installation Kit have been removed from tub.
■■
Washer is plugged into electrical outlet and is properly grounded.
■■ Water hoses are connected to the faucet’s with inlet screens and washers.
■■ Water is turned on and checked for leaks at faucet and water valve connections.
■■ Drain hose is properly located into drain facility and is not collapsed or damaged.
■■ Washer has been properly leveled. All legs should be firmly on the floor and leveling leg lock nuts MUST
be tightened.
■■ Test for proper operation by running the washer through the following complete cycle.
Page 4
COLD WEATHER STORAGE
The following precautions should be taken if a washer is to be stored, after use or where it would be subject to
freezing conditions.
1. Turn off the water supply, then remove the inlet hoses.
2. Select a fill cycle and energize the water valve by selecting a warm water setting. A few seconds of fill is sufficient.
3. Disconnect from electrical supply.
4. Remove the drain hose cover from upper left corner of cabinet back.
5. Lower the drain hose to floor level and tilt washer backwards to remove water from the drain hose and pump.
6. Re-install the drain hose cover.
7. When machine is reinstalled allow machine to stabilize to room temperature. See location considerations.
FLOORING
For best performance the washer must be installed on a solidly constructed floor. Wood floors may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting and soft tile surfaces are contributing factors in vibration and/or tendency for a washer to move slightly during the spin cycle. Never install the washer on a
platform or weakly supported structure.
LOCATION CONSIDERATIONS
It is recommended the washer never be installed in areas where water may freeze since the washer will always
maintain some water in the water valve, pump and hose areas. This can cause damage to belts, pump, hoses and
other components. Operating temperature should be above 60°F.
ALCOVE OR CLOSET INSTALLATION
MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:
Sides – 0 in. Rear – 1.75 in.
Top – 19 in. Closet Front – 0 in.
The closet front must have a total unobstructed air opening of 72 sq. in. minimum. A louvered door with equivalent
air opening is acceptable.
IMPORTANT TO INSTALLER
PLEASE READ THE PRECEDING INSTRUCTIONS CAREFULLY BEFORE STARTING TO INSTALL THE WASHING MACHINE. THESE INSTRUCTIONS SHOULD BE RETAINED FOR FUTURE REFERENCE.
REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES TO AVOID THE DANGER OF A CHILD
SUFFOCATING.
ADDITIONAL INFORMATION
50 HERTZ OPERATION
This Maytag appliance is manufactured for operation on 60 Hz AC approved electrical service. This model is not
designed for use on 50 Hz AC electrical service and conversion of the product from 60 to 50 Hz operation is not
recommended. For additional information on 50 Hz products, write:
MAYTAG INTERNATIONAL, INC.
1475 EAST WOODFIELD ROAD
SCHAUMBURG, ILLINOIS 60173
Phone: 847-273-3100
FOR TECHNICAL ASSISTANCE, REPLACEMENT PARTS AND ACCESSORIES
For technical assistance or if your washer requires replacement parts or accessories, contact Maytag Customer Service,
toll-free 1-888-4-Maytag for information on the nearest authorized Maytag Parts Distributor.
Loading...