Maytag DN5000, DN3000 User Manual

Download

Page 1

Glass Front Vender by Maytag DN5000

Beginning Production Run 8063BY

DN3000

Beginning Production Run 8292DB

Manufactured by

Dixie-Narco, Inc. P.O. Drawer 719 Williston, SC 29853-0719 803-266-5001 fax: 803-266-5049 Visit us on the web: www.dixienarco.com

803,903,030.71

Page 2

GENERAL INFORMATION

of 90

Table of Contents

GENERAL INFORMATION .............................................................................................................................3

VENDER SAFETY PRECAUTIONS ...............................................................................................................................................3

PRODUCT IDENTIFICATION........................................................................................................................................................3

PHYSICAL CHARACTERISTICS...................................................................................................................................................3

INSTALLATION & SETUP..............................................................................................................................4

RECEIVING INSPECTION............................................................................................................................................................4

UNPACKING THE VENDERS .......................................................................................................................................................4

ELECTRIC POWER NEEDED .......................................................................................................................................................4

DO NOT USE AN EXTENSION CORD. ..........................................................................................................................................4

GROUND THE VENDER...............................................................................................................................................................4

COIN CHANGERS & OTHER ACCESSORIES ............................................................................................................................4-5

PLACING THE VENDER ON LOCATION .......................................................................................................................................5

INSTALLATION AND SET UP INSTRUCTIONS..............................................................................................................................6

PROGRAMMING........................................................................................................................................7-28

GENERAL MAINTENANCE..........................................................................................................................29

POWER.....................................................................................................................................................................................29

CLEANING.................................................................................................................................................................................29

EPROM REPLACEMENT............................................................................................................................................................29

MAJOR COMPONENT DESCRIPTION .................................................................................................30-37

AC DISTRIBUTION BOX.............................................................................................................................................................30

REFRIGERATION UNIT..............................................................................................................................................................30

KO BOARDS.........................................................................................................................................................................31-32

MACHINE BOARDS ..............................................................................................................................................................33-34

WIRING DIAGRAMS..............................................................................................................................................................35-36

TROUBLESHOOTING.............................................................................................................................38-59

ASD DISPLAY............................................................................................................................................................................38

CONTROL BOARD ISSUES...................................................................................................................................................39-42

COIN MECH ISSUES.............................................................................................................................................................43-46

COMPRESSOR ISSUES........................................................................................................................................................47-48

SOLENOIDS .........................................................................................................................................................................49-50

CONVEYOR ISSUES..................................................................................................................................................................51

ELEVATOR ISSUES...................................................................................................................................................................52

FAN MOTOR ISSUES.................................................................................................................................................................53

KEYPAD ISSUES..................................................................................................................................................................54-55

LIGHT ISSUES......................................................................................................................................................................56-57

TEMP SENSOR ISSUES.............................................................................................................................................................58

ICE / FROST ON EVAPORATOR.................................................................................................................................................59

CONDENSATE ON OUTSIDE OF PRODUCT DOOR....................................................................................................................59

COMPRESSOR RUNS CONTINUOUSLY ....................................................................................................................................59

PARTS INDEX ..........................................................................................................................................60-90

MACHINE FRONT VIEW........................................................................................................................................................61-62

CABINET DETAIL..................................................................................................................................................................63-64

SERVICE DOOR ..................................................................................................................................................................65-68

TRAY ASSEMBLY.................................................................................................................................................................69-70

AC DISTRIBUTION BOX........................................................................................................................................................71-72

ELEVATOR...........................................................................................................................................................................73-74

CONVEYOR..........................................................................................................................................................................75-76

LIGHTING.............................................................................................................................................................................77-78

REFRIGERATION.................................................................................................................................................................79-80

ELECTRONICS.....................................................................................................................................................................81-82

HARNESSES.............................................................................................................................................................................83

LABELS / DECALS / MISC...........................................................................................................................................................84

WASHERS , BOLTS, AND MISC. HARDWARE .......................................................................................................................85-90

LEVEL THE VENDER.....................................................................................................................................................5

SPACE THE VENDER....................................................................................................................................................5

LOADING THE VENDER ................................................................................................................................................5

PRODUCT..................................................................................................................................................................5-6

GLASS DOOR..............................................................................................................................................................29

TRAYS / TRAY INSERTS..............................................................................................................................................29

SLIDE/PUSHER ASSEMBLY ........................................................................................................................................29

CABINET.....................................................................................................................................................................29

DRAIN PAN.................................................................................................................................................................29

REFRIGERATION CONDENSER..................................................................................................................................29

COIN ACCEPTOR........................................................................................................................................................29

LUBRICATING THE VENDER.......................................................................................................................................29

Page 3

GENERAL INFORMATION

of 90

GENERAL INFORMATION

VENDER SAFETY PRECAUTIONS

Please read this manual in its entirety. This service information is intended to be used by a qualified service technician, who is familiar with proper and safe procedures to be followed when repairing, replacing, or adjusting any Dixie-Narco vender components. All repairs should be performed by a qualified service technician who is equipped with the proper tools and replacement components, using genuine Dixie-Narco factory parts.

REPAIRS AND/OR SERVICING ATTEMPTED BY UNQUALIFIED PERSONS CAN RESULT IN HAZARDS DEVELOPING DUE TO IMPROPER ASSEMBLY OR ADJUSTMENTS WHILE PERFORMING SUCH REPAIRS. PERSONS NOT HAVING A PROPER BACKGROUND MAY SUBJECT THEMSELVES TO THE RISK OF INJURY OR ELECTRICAL SHOCK WHICH CAN BE SERIOUS OR EVEN FATAL.

PRODUCT IDENTIFICATION

The production date of Dixie-Narco products is determined by the date code incorporated in the serial number.

The vender serial number takes the form xxxxyyyyzz. The first 4 digits (xxxx) identify the specific vender. The next 4 digits (yyyy) identify the manufacturing run that the vender was built in. The last two alpha characters (zz) identify the quarter and the year the vender was built. The first alphacharacter identifies the quarter.

A = 1st quarter B = 2nd quarter C = 3rd quarter D = 4th quarter

The second alpha-character identifies the year:

Y = 2000 Z = 2001

PHYSICAL CHARACTERISTICS

DN5000

HEIGHT 71.25” (1809.75) WIDTH 52.25” (1327.15 mm) DEPTH 35” (889 mm)

DEPTH WITH VALIDATOR SHIPPING WEIGHT

Glass front is 34” (863.6 mm) wide, 67” (1701.8 mm) high

36.5” (927.1 mm) 749 lbs. (340 kg)

DN3000

HEIGHT 71.25” (1809.75) WIDTH 42.25” (1073.15 mm) DEPTH 35” (889 mm)

DEPTH WITH VALIDATOR SHIPPING WEIGHT

Glass front is 21.1” (614.14 mm) wide, 67” (1701.8 mm) high

36.5” (927.1 mm) 682 lbs. (310 kg)

Page 4

INSTALLATION & SETUP

of 90

INSTALLATION & SETUP

The Dixie-Narco Coca-Cola Glass Front Vender is designed utilizing the latest technology.

60 Hertz). The cabinet serial plate also indicates the Amperage of the vender. The vender must be plugged in to its own properly rated single phase, alternating current outlet with its own circuit protection (fuse/circuit breaker).

RECEIVING INSPECTION

DO NOT STORE THE VENDER OUTSIDE. THIS MACHINE IS FOR INDOOR USE ONLY.

Upon receipt, inspect the vender for any shipping damage. If there is any damage have the driver note the damage on the bill of lading and notify Dixie-Narco. Although the terms of sale are FOB shipping point, which requires the consignee to originate shipping damage claims, Dixie-Narco will gladly help if you must file a claim.

UNPACKING THE VENDERS

Remove the stretch wrap fiberboard edge protectors and corrugated front protector from the outside of the vender.

DO NOT STORE THE VENDER OUTSIDE WITH THE STRETCH WRAP ON. THIS COULD CAUSE THE STRETCH WRAP TO BOND TO THE VENDER’S SURFACE, WHICH COULD DAMAGE THE FINISH.

Remove the shipping boards from the bottom of the vender. The shipping boards are attached by the leveling legs. To avoid unnecessary damage to the leveling legs or base, remove shipping boards by using a 1 – ½ inch socket type wrench to unscrew the leveling legs. Be sure to replace the legs after removing the shipping boards. Once the vender is unpacked, check the service area for any additional parts, price/product labels, service/operation manual, or other information concerning factoryequipped accessories such as coin mechs and validators.

WARNING: TO AVOID THE

POSSIBILITY OF A FIRE HAZARD, DO NOT STORE ANYTHING OR ALLOW DEBRIS OF ANY KIND TO ACCUMULATE IN THE BOTTOM OF THE

SERVICE AREA, IN AND AROUND THE REFRIGERATION COMPARTMENT OF THE CABINET, OR IN FRONT OF THE EVAPORATOR AND CONDENSER COILS.

ELECTRIC POWER NEEDED

Refer to the cabinet serial number plate to determine the proper voltage and frequency the machine requires (domestically this requirement is 120 Volts,

DO NOT USE AN EXTENSION CORD.

GROUND THE VENDER

The vender is equipped with a three wire power supply cord and MUST be plugged into a properly grounded outlet.

DO NOT REMOVE THE GROUND PIN OR IN ANY WAY BYPASS, MODIFY, DEFEAT, OR DESTROY THE GROUNDING SYSTEM OF THE VENDER.

If the outlet will not accept the power cord plug, contact an electrician to install a proper AC outlet.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY SUBJECT THE USER TO THE RISK OF INJURY OR ELECTRICAL SHOCK WHICH CAN BE SERIOUS OR FATAL.

COIN CHANGERS & OTHER ACCESSORIES

The vender must have an MDB coin changer installed and can have an MDB bill acceptor installed. If the MDB coin changer and other MDB accessories are not factory installed, refer to the instructions received from the manufacturer of the MDB coin changer and other MDB accessories for proper set-up and installation.

The Vender will support the following MDB coin changers:

Multi-Drop Coin Mech (Domestic)

Coinco 9302GX Conlux CCM-5G Mars TRC6510 Mars TRC 6512

The Vender will support the following MDB bill validators:

Multi-Drop Bill Validators (Domestic)

Coinco BA30B, BA50, MAG30, MAG50 Mars VN2512, VN2502, VN2312 Conlux NBM-3000 Series, MKA-2141-11 Ardac 5500 Series

Page 5

INSTALLATION & SETUP

of 90

The Vender will support the following MDB card readers:

Multi-Drop Card Readers (Domestic)

Debitek Smart Card - MDB Danyl Schlumberger

(At publication swipe reader had not

been tested) Fage MDB Diebold Systems AT&T Campus Wide VMC LTD Jofemar Evend.net

PLACING THE VENDER ON LOCATION

The Coca-Cola Glass Front Vender is for INDOOR USE ONLY. It should be kept out of direct sunlight

and away from any heat source.

!! CAUTION !!

DO NOT TRANSPORT THE VENDER TO OR FROM THE LOCATION LOADED WITH PRODUCT OR DAMAGE TO THE VENDER MAY RESULT. ENSURE TRAY ASSEMBLIES ARE SECURED WHEN MOVING THE VENDER OR DAMAGE TO THE VENDER MAY RESULT.

The vender must be located on a solid, flat, and level surface. Ensure the flooring can bear the weight load of a fully stocked vender (approximately 1150 lbs. DN5000 or 1012lbs. DN3000). The vender must be positioned close enough to an electrical outlet so that an extension cord is not required. If the machine will be subject to user misuse or vandalism, it is recommended that the vender be secured to the floor or wall as described in DixieNarco Technical Bulletin 344. Due to the large size and weight of the vender, never attempt to move the vender with a hand truck or stair climber. The vender should be moved with a Pallet Jack or Vender/Cooler Dolly at all times. The vender should never be slid or pushed in place. Never side load the leveling legs, doing so will damage the legs.

LEVEL THE VENDER

Adjust the front leveling legs, ensuring that an even gap exists between the glass door and the top security angle and receiver box, then level the cabinet front-to-rear. A carpenter’s level will help verify that the machine is level. Leveling legs are adjusted using a wrench or socket 1 – ½ inch in size. Lowering the legs will raise the machine approximately 1/4” per 4 turns. If the machine is to

be used next to another vender, check the top and side for proper alignment. Minimum leg extensions should be used in leveling and alignment to attain greater stability. Make sure that all the leveling legs are in contact with the floor. If you cannot level the vender, select another location. Do not place any objects under the machine. Leveling is extremely important to ensure proper vender operation.

DANGER

The vender must be properly located and leveled. If the machine will be subject to user misuse or vandalism it is recommended that the vender be secured to the floor or wall as described in Dixie-Narco Technical Bulletin 344 to minimize risk of injury or death from tipping. Call the DixieNarco Technical Service Department or your local Dixie-Narco Representative for assistance.

SPACE THE VENDER

Do not block the rear of the vender. Keep the vender 4 inches (10 cm) from the wall to ensure adequate airflow to the condenser and compressor. At the front of the vender, make sure that nothing obstructs the air intake at the bottom of the service door and cabinet. At the rear of the vender, make sure nothing obstructs the air exhaust at the bottom of the cabinet.

WARNING: TO AVOID THE

POSSIBILITY OF A FIRE HAZARD, DO NOT STORE ANYTHING OR ALLOW DEBRIS OF ANY KIND TO ACCUMULATE IN THE BOTTOM OF THE

SERVICE AREA, IN AND AROUND THE REFRIGERATION COMPARTMENT OF THE CABINET, OR IN FRONT OF THE EVAPORATOR AND CONDENSER COILS.

LOADING THE VENDER

All Coca-Cola Glass Front venders are shipped ready to vend 20 oz. bottles unless another package was specified at the time the vender was ordered from the factory. If a package other than these are to be vended, contact a Dixie-Narco Factory Service Representative or refer to the proper Technical Publication for spacer settings.

PRODUCT

The Coca-Cola Glass Front Vender is designed to vend a wide range of cans, glass, and plastic beverage containers in sizes from 12 oz. to 20 oz. It has a double-pane or triple pane, tempered safety

Page 6

INSTALLATION & SETUP

of 90

glass door for clear viewing of all products. The machine is set up with: 5 Trays, 9 columns or 6 columns each, 8 products per column. Maximum capacity for DN5000 is 15 cases (360 items) of 20 oz. Product and DN3000 is 10 cases (240 items) of 20oz. product.

• Locate the KO control board mounted on the

right side wall.

• Remove the battery from its holder (B 1).

INSTALLATION AND SETUP INSTRUCTIONS

Open the service door on the right side using the key provided in the coin return cup, or if shipped with a locking clip, remove the clip and install the lock.

Ensure the power switch on the AC distribution box is in the off position.

Check that all connectors are firmly seated on the control boards and at the various components on the service door (coin mech, keypad, etc.).

Retrieve the main power plug from the hole in the rear of the vender and plug the cord in a properly grounded 120VAC, 15 Amp receptacle (U.S. and Canada).

Open the service door and apply power to the AC distribution box by means of the rocker switch (if equipped with a bill acceptor, the acceptor should cycle twice). The display on the door should scroll “*/SOFTWARE/REV###.##/ICE COLD COCACOLA/##.##”, fluorescent lamp should be lit and the cooling unit should start. (Note: There is an approximate 2 minute delay)

IF THE DISPLAY SCROLLS “OUT OF SERVICE”, OR THE COOLING UNIT FAILS TO START, REFER TO THE TROUBLESHOOTING FLOWCHARTS BEGINNING ON PAGE 38.

SERVICE NOTE

Battery Backup The battery backup is used to retain information programmed in the system (pricing, time, date, etc.) in case of power interruptions, or any time the main power is off. When the vender is shipped, the battery is connected and memory is being maintained. If the vender is to be stored for long periods of time, disconnecting the battery is recommended. The following steps will guide you through this procedure.

• Open the service door, turn the main power switch to the off position or unplug the main power harness located on the front of the power box.

LOADING CHANGE TUBES

MDB UNITS Open the service door. Enter “TUBEFILL” in programming. Load the coin mechanism with coins by inserting coins in the separator on the coin mech. Display will show the total number of the coin type being entered as they are installed. (i.e. .05 1, .10 3, .25 8).

Note: A low coin level in the coin tubes will

interfere with operation of the bill validator.

(For additional information about coin mechanism refer to the manufacturer’s instructions.)

LOADING PRODUCT

Proper product loading and product sizing to spacer/gate and elevator / conveyor are very important in ensuring problem free vending. Pay close attention to the product’s center of gravity. Regional products are sometimes bottled and/or canned in unique shapes and sizes. These products must be tested for problem-free vending before large quantities are purchased.

Note: Loading should be done as quickly as

possible to minimize product/cabinet exposure to warmth and humidity.

Open the service door then open the product compartment glass door.

After loading is finished check the price tags to ensure they correspond to existing products. Pricing labels are located in the service bag shipped with every vender.

Close the product compartment glass door. Close the service door and lock. Closing the service

door will place the machine in service and start the refrigeration cycle.

Page 7

PROGRAMMING

of 90

PROGRAMMING

COCA-COLA EVS GLASS FRONT PROGRAMMING METHOD

April 2000

NORMAL MODE:

In normal mode, on power up display will show software installed in vender, then change to POS message or decimal point and / or vend price. When money is inserted, the display indicates the total amount of the deposit. The keys on the keypad are used to select the product. In normal mode you may access an external menu for reading historical sales counters, cash counters, error codes, none, or return to normal mode.

SERVICE MODE: If configuration switch 4 is set to “C4 0”, when the door is opened, “NONE” or a list of Error codes will show on the display. If configuration switch 4 is set to “C4 1”, when the door is opened, “CASH - ####-##.##”, “CARD - ######.##”, “SALES - #### -####”, “ERROR”, or “NONE” will show on the display. NOTE: Card is only shown if a card reader is present. The service mode is entered when the door is open and the service switch on the KO controller is pressed. The operator can now use the keypad to move through the main routine menu.

Key number 1: Abort/Cancel - will return to previous menu prompt. Key number 2: Scroll Up - forward in menu. Key number 3: Scroll Down - backward in menu. Key number 4: Enter/Save/Clear - Allows you to enter a specific routine, save what you have programmed, or

clear the error prompts.

Note: Routines with * are password protected. They can only be viewed and entered after the password is

entered at the “PASS” prompt.

EXTERNAL MENU MODE: The information available in this mode is obtainable with the door closed or open as long as the vender is in normal mode, by entering the password which is set at 4, 2, 3, 1. Note: 4231 is the factory default and can be programmed to any four digit combination. Information available is historical cash counted, resettable cash counted for each selection, historical sale (total number of vends), resettable vends counted for each selection, error codes, and return. Refer to the “CASH”, “SALES”, AND “ERROR” routines for instructions to move through the menus.

PROGRAMMING MENU

“ERROR” - ERROR ROUTINE

This function allows you to enter the error readout routine. ERROR will appear when you press the service button on the control board. Press key number 4, if there have been no errors since the last reset, the display will read “NONE”. If one or more errors have occurred, the display will show the first error code that occurred.

The following are error codes that may be displayed and detailed information accessed: “NONE”, “VENDMECH”, “CONTROL”, “SELECTSW”, “CHANGER”, “BILL VAL”, “CARD RDR”, “ONLINE”, “RVEND”, “SEL/DISP”, “RFRIG”, “DNC ERR”, “HEALTH”.

Press key number 2 or 3 to scroll through any error codes that are present. Important: If there is only one problem, that will be the only error code shown when you enter the error code sub-

menus.

With an error code showing on the display, press key number 4 to access detailed information. After making repairs with an error code showing on the display, press and hold key number 4 for 2 seconds will clear the error. Press key number 1 to return to “ERROR”.

Page 8

PROGRAMMING

of 90

“VENDMECH” - Vend Mechanism Summary Errors Press key number 4 and the display will show the following:

- “COLJAM#”, where # is the column number detected jammed.

Press key number 1 will return to “VENDMECH” if all vend mech errors have not been cleared. If all vend mech errors have been cleared the next error mode will be displayed, or “NONE” if there are no errors.

Press key number 1 will return to “ERROR”. “CONTROL” - Control System Summary Errors

Press key number 4 and the display will show one of the following:

- “DOORSWIT”, indicating a door switch in the open position for more than 1 hour.

- “RAM ERR”, indicating the check sum for service mode settings memory has been corrupted.

- “AC LOW”, indicating AC supply to the machine has fallen more than 15% below normal line voltage for more than 30 seconds.

- “SCALEER”, indicating a peripheral has introduced a scaling factor that is incompatible with current setting.

Press key number 1 will return to “CONTROL” if all control system errors have not been cleared. If all control system errors have been cleared the next error code will be displayed, or “NONE” if there are no errors.

Press key number 1 will return to “ERROR”. “SELECTSW” - Select Switch Summary Errors

Press key number 4 and the display will show “SELSW#”, indicating a key on the keypad has been active for more than 15 seconds while in normal (sales) mode.

Press key number 1 will return to “SELECTSW” if all selection errors have not been cleared. If all selection errors have been cleared the next error code will be displayed or “NONE” if there are no errors.

Press key number 1 will return to “ERROR”. “CHANGER” - Changer Summary Errors

Press key number 4 and the display will show one of the following:

- “COINCOMM”, indicating a changer communication error. (No communication for more than 2 seconds)

- “TUBESENS”, indicating a tube sensor error.

- “COININLE”, indicating an inlet chute blocked error (no coins sensed in acceptor for 96 hours).

- “TUBJAM #”, indicating a tube jam error.

- “COIN ROM”, indicating a changer ROM check sum error (failed changer).

- “EXCESSES”, indicating excessive escrow attempts (more than 255 since last coin sensed).

- “COIN JAM”, indicating a coin jam reported by coin mech.

- “LOW ACCP”, indicating a low coin acceptance rate (less than 80%).

- “ACCDISCN”, indicating an acceptor is unplugged.

- “ROUTING”, indicating a coin was mis-routed.

Press key number 1 will return to “CHANGER” if all changer errors have not been cleared. If all changer errors have been cleared the next error code will be displayed or “NONE” if there are no errors.

Press key number 1 will return to “ERROR”.

Page 9

PROGRAMMING

of 90

“BILL VAL” - Bill Validator Summary Errors Press key number 4 and the display will show one of the following:

- “BILLCOMM”, indicating a bill validator communication error. (No communication for more than 5 seconds)

- “BILLFULL”, indicating the bill stacker is full.

- “BILL MOT”, indicating a defective motor in the validator.

- “BILL JAM”, indicating a bill jam in the validator.

- “BILL ROM”, indicating a check sum error.

- “BILLOPEN”, indicating an open stacker.

- “BILLSENS”, indicating a bill validator sensor error.

Press key number 1 will return to “BILL VAL” if all changer errors have not been cleared. If all validator errors have been cleared the next error code will be displayed or “NONE” if there are no errors.

Press key number 1 will return to “ERROR”. “CARD RDR” - Card Reader Summary Errors

Press key number 4 and the display will show one of the following:

- “CARDCOMM”, indicating no card reader communication for 5 seconds.

- “CARD #”, indicating the most recent “non-transient error” from the card reader (failed card reader).

Press key number 1 will return to “CARD RDR” if all changer errors have not been cleared. If all card reader errors have been cleared the next error code will be displayed or “NONE” if there are no errors.

Press key number 1 will return to “ERROR”. Press key number 2 will scroll to the next routine.

“ONLINE” - Online Module Error Press key number 4 and the display shows one of the following:

- “ONLINE”, indicating no communications to online module for 5 seconds.

- “ONL COMM”, indicating the online network is not responding, online module cannot call out.

- “ONL INTL”, indicates an online module internal problem causing improper functioning.

Press key number 1 will return to “ONLINE” if all online module errors have not been cleared. If all online module errors have been cleared the next error code will be displayed or “NONE” if there are no errors. Press key number 1 will return to “ERROR”. Press key number 2 will scroll to the next routine.

“RVEND” - Remote Vend Mechanism (USD) Error. Press key number 4 and the display shows one of the following.

- “RV COMM#”, indicates no communication for 5 seconds with remote vend mech at address “#”.

- “RVEND a#”, indicates error code number “#” from the remote vend mech at address “a”.

Press key number 1 will return to “RVEND” if all remote vend mechanism errors have not been cleared. If all remote vend mechanism errors have been cleared the next error code will be displayed, or “NONE” if there are no errors. Press key number 1 will return to “ERROR”. Press key number 2 will scroll to the next routine.

“SEL/DISP” - Selection / Display Device (ASD) Error

Press key number 4 and the display shows:

- “S/D COMM”, indicating no communication to selection / display device for five seconds.

Press key number 1 will return to “SEL/DISP” if all selection / display device errors have not been cleared. If all selection / display device errors have been cleared the next error code will be displayed or “NONE” if there are no errors. Press key number 1 will return to “ERROR”. Press key number 2 will scroll to the next routine.

Page 10

PROGRAMMING

of 90

“REFRIG” - Refrigeration Summary Errors Press key number 4 and the display shows one of the following:

- “TEMPSENS”, indicating the temperature sensor is defective or unplugged.

- “TOO COLD”, indicating the cabinet temperature is 30 F below lower limit.

- “TOO HOT”, indicating the cabinet temperature is 30 F above upper limit.

- “NO COOL”, indicating the cooling system has failed to decrease temperature 10 F per hour while the compressor is running.

Press key number 1 will return to “REFRIG” if all refrigeration summary errors have not been cleared. If all refrigeration summary errors have been cleared the next error code will be displayed, or “NONE” if there are no errors. Press key number 1 will return to “ERROR”. Press key number 2 will scroll to the next routine.

“DNC ERR” - Dixie-Narco Corporation Summary Errors Press key number 4 and the display will show one of the following:

- “MB COMM”, indicating the machine board has stopped communicating. The display will scroll “NO SALE” when this error has occurred.

- “ELEVATOR”, indicating an elevator operation error has occurred.

- “CONVEYOR”, indicating a conveyor operation error has occurred.

- “PORT DR”, indicating the read switch not being recognized at port door.

Press key number 1 will return to “DNC ERR” if all Dixie-Narco Corporation Summary errors have not been cleared. If all Dixie-Narco Corporation Summary errors have been cleared the next error code will be displayed or “NONE” if there are no errors. Press key number 1 will return to “ERROR”. Press key number 2 will scroll to the next routine.

“HEALTH” – HEALTH TIMER CONSTRAINT ERRORS

Press key number 4 and the display shows one of the following.

- “HTIN” – Health Timer Error The initial pull down time has not met the health timer constraints. Refer to “HEALTH” section for details. Press and hold key number 4 for 2 seconds will clear the error and the display will show “NONE”.

- “HCOD” – Health Code Error The health code cooling constraints have not been met. Refer to “HEALTH” section for details. Press and hold key number 4 for 2 seconds will clear the error and the display will show “NONE”.

- “RCHE” – Recheck Error The extended health timer has not met the health timer constraints. Refer to “HEALTH” section for details. Press and hold key number 4 for 2 seconds will clear the error and the display will show “NONE”.

“COINPAYO” - COIN PAYOUT ROUTINE This function allows you to dump coins from the coin mechanism. Press key number 4 to enter mode and the lowest coin value dispensable will show on the display. Press key number 2 or 3 to scroll through the different coin values available. Press and hold key number 4 to dump the coins whose value is shown on the display.

Press key number 1 will return to “COINPAYO”. Press key number 2 to scroll to the next routine.

“TUBEFILL” - TUBE FILL ROUTINE

This function allows you to count the coins loaded in the top (separator) of the coin mech that will be routed to an inventory tube. Press key number 4 to enter mode and the total number of the coin type being loaded will be displayed and counted in the vender controller as they are accepted. The controller will inhibit the acceptance of any coin which does not go to a tube during this procedure. If a tube full status is detected, that coin type will be inhibited. When you finish loading all coins:

Press key number 1 to return to “TUBEFILL”. Press key number 2 to scroll to the next routine.

Page 11

PROGRAMMING

of 90

“TESTMODE” - TEST ROUTINE This function allows you to diagnose different functions of the vender. Press key number 4 and the display will show “TESTVEND”.

Press key number 2 or 3 to scroll through the test routines available. Press key number 1 to return to “TESTMODE”.

“TESTVEND” - Vend Testing This function allows you to test vend each column. Press key number 4 and the display will show “COL A1”. Press key numbers 2 or 3 to scroll through the columns available to run in motor test. Press key number 4 to run the motor of the column displayed. Press key number 1 will return to “TESTVEND”. Press key number 2 to scroll to next test mode.

“TEST SEL” - Select Switch Test This function allows you to test each selection. Press key number 4 and the display will show “SEL 4”. Then press any key and the display will show the last key number pressed. Press and hold key number 1 for approximately 5 seconds will return to “TEST SEL”. Press key number 2 to scroll to the next test mode.

“DISPLAY” - Display Test This function allows you to test all segments in the display. Press key number 4 and the display segments will illuminate in the following manner; “*0.” will scroll continuously. Press key number 1 to return to “DISPLAY”. Press key number 2 to scroll to next test mode.

“RELAYS” - RELAY TEST This function allows you to test the relay electronic control of the compressor (“COMPR #”), the evaporator fan(s) (“FAN #”), and the sign front light (“LIGHT#”).

CAUTION: Disconnect power to the compressor before testing the compressor relay. Failure to

disconnect power to the compressor before testing the relay could result in damaging the compressor.

Press key number 4 and the display will show “COMPR#”, where # is the state of the relay 0 = not activated or off; 1 = activated or on . Press key number 4 to toggle the relay on and off. Press key number 2 to scroll to “FAN#”, where # is the state of the relay - 0 = not activated or off, 1 = activated or on. Press key number 4 to toggle the fan(s) on and off. Press key number 2 to scroll to “LIGHT#”, where # is the state of the relay - 0 = not activated or off; 1 = activated or on. Press key number 4 to toggle the lights on and off. Press key number 1 to return to “TESTMODE”. Press key number 2 to scroll to “PASSWORD”.

* “PASSWORD” - PASSWORD ROUTINE This function allows you to enter the following routines which are not accessible until the operator enters a password, which is set as 4-2-3-1. To enter the password, press key number 4 until the display goes blank. Then press key number 2, then 3, then 1, and then 4, and “CASH” should appear on the display. If not entered properly, the display will return to “PASSWORD” after approximately 16 seconds. If entered correctly, the display will go to the next function “CASH”.

Page 12

PROGRAMMING

of 90

* “CASH” - CASH COUNTER ROUTINE This function will show the user the vender historical total cash counted and the resettable cash counted for each selection for the vender.

Press key number 4 and “CASH”/”######.##” will show on the display where the 8"#” characters are the historical total cash counters that have been recorded. Note: Leading zeros are not displayed. Example: Display flashes “CASH”, then “262500”. This is $2625.00 historical total cash. Press key number 2 to scroll to “CARD”/######.##”, where the 8# characters are the historical card reader cash counters. Note: Leading zeros are not displayed. Press key number 2 or 3 to display “COL A1”/”######.##” where the 8"#” characters are the resettable cash counters for that selection. Note: Leading zeros are not displayed. Pressing key number 2 or 3 at this time will scroll through the available selection cash counters. Example: Display flashes “COL A1”, then “520.50”. This is $520.50 resettable cash for selection A1. Press key number 1 to return to “CASH”/”######.##”. Press key number 1 to return to “CASH”.

Press key number 2 to scroll to the next routine. * “SALES” - SALES COUNTER ROUTINE

This function will show the user the vender historical total number of vends and the resettable vends counted for each selection for the vender.

Press key number 4 and “SALES”/”########” will show on the display where the 8"#” characters are the historical total vend counters that have been recorded. Note: Leading zeros are not displayed. Example: Display flashes “SALES”, then “1325”. This is 1325 historical vends. Press key number 2 or 3 to display “COL A2”/”########”, where the 8"#” characters are the resettable vend counters for that selection. Note: Leading zeros are not displayed. Pressing key number 2 or 3 at this time will scroll through the available selection vend counters. Example: Display flashes “COL A1” then “145”. This is 145 resettable vends counted for selection A1. Pressing key number 1 will return to “SALES”/”########”. Press key number 1 to return to “SALES”.

Press key number 2 to scroll to the next routine. * “PRICE” - PRICE SETTING ROUTINE

This function allows the user to set pricing. When Configuration Code 1 is programmed to “C1 1”, multi-pricing a price for each selection needs to be set. Note: This routine is lockable when using a data collection device.

Press key number 4 and “PRICE A1” (multiprice) or “SNGPRICE” (single price) will show on the display. Press key number 4 to set the price on selection A1, “00.00” or current price setting will show on the display. Press key number 2 or 3 to change the price setting for selection A1. Press key number 4 to enter the price selected and the display will return to “PRICE A1”. Press key number 2 to scroll to the next selection you wish to set price. Press key number 4, set the price and enter the price. Repeat these steps for each selection until all prices are set. Note: In multiprice modes, selections go “PRICE A1” through “ALL SELS”.

If Configuration Code 1 is programmed to “C1 O”, single price, set “SNGPRICE” as described above. The price entered for “SNGPRICE” will be set for all selections. Press key number 1 to return to “PRICE”. Press key number 2 to scroll to the next routine.

Page 13

PROGRAMMING

of 90

“STS PROG” – SPACE TO SALES ROUTINE

This function allows you to change the space to sale settings. Press key number 4 and “OPTION#” or “CUST STS” will show on the display, which indicates the current space to sales option. For the 7 options available, see list below. Press key number 2 to scroll through the options. Press key number 4 with the desired option showing on the display to save that option and return to “STS PROG”.

Space to Sales Options:

“OPTION1” 1 to 1 = Columns are assigned to selections with the same number. “OPTION2” Tray = Full tray assigned. Example: selections A1 thru A9 vend from columns A1 thru A9

sequentially.

“OPTION3” Half Tray = Half tray assigned. Example: selections A1 thru A5 vend from columns A1

thru A5 sequentially and selections A6 thru A9 vend from columns A6 thru A9 sequentially.

“OPTION4” Groups of 3 = Groups of 3 columns are assigned sequentially to work with associated

selections. Example: selections A1 thru A3 vend from columns A1 thru A3 sequentially.

“OPTION5” Combined groups of 2 & 3 = Selection grouping per tray will be assigned columns 1 & 2;

3 & 4; 5 & 6; 7, 8, & 9 working with associated selections.

“OPTION6” Combined groups of 3 = Selection grouping per tray will be assigned columns 1, 2, & 3;

4, 5, & 6; 7, 8, & 9 working with associated selections.

“CUST STS” Custom space to sales = Allows you to assign columns in blocks working with associated

selections.

With “CUST STS” showing, press key number 4 and “CLEAR?” will show on display. Press key number 4 will clear the current space to sale settings. Press key number 1 will return to “CUST STS”. Press key number 4 will show “SEL A1” alternating with columns assigned to blocks. Press key number 4 will show “FIRST A1” or the individual selection to start a block. Press key number 2 to scroll to “FIRST E9” or the largest selection available. Press key number 4 will show “LAST A1” or the last column for custom space to sales blocks. Press key number 2 will show “LAST A1” or the largest column for custom space to sales blocks available. Press key number 4 will show “SAVE?” Press key number 4 will save the new settings.

IMPORTANT: Selection to Column assignments are only for each Tray. Example: Selection A1 can only be tied to columns on the A Tray.

Page 14

PROGRAMMING

of 90

* “CONFIG” - MACHINE CONFIGURATION This function allows the user to access and change the programming of the following machine configuration settings. Note: This routine is lockable when using a data collection device. If you press key number 4 and the display shows “LOC”, this means configuration setting changes will not be allowed. If “CON 1” is displayed, then configuration setting changes will be allowed. “LOC” can only be enabled or disabled through DEX interrogation. If “CON1” is displayed, the listed settings are available. Note: You must press key number 4 with the configuration code displayed if you wish to enter the edit mode. The “0” or “1” will be flashing to acknowledge you are in the edit mode.

IMPORTANT: All machine configuration codes are disabled coming from the factory (CON # 0). CON 1 - Configuration Switch 1 - Multi-Price Setting Mode

This code is used to enable the single price mode “CON 1 0” or multi-price mode “CON 1 1”. Press key number 4 and “CON 1 #” will be displayed, with the “#” flashing. Press key numbers 2 or 3 to scroll between “CON 1 0” and “CON 1 1”. Press key number 4 with the display flashing the setting you wish to use. Press key number 1 to return to “CON 1”. Press key number 2 to scroll to “CON 2”.

CON 2 - Configuration Switch 2 - Optional Features Enable This code is used to allow (CON 2 1) the following optional features to be displayed and enabled: “LIGHT”, “DISCOUNT”, “OVERRIDE”, “SELBLCK1”, and “SELBLCK2”. Press key number 4 and “CON 2 #” will be displayed with the # flashing. Press key numbers 2 or 3 to scroll between “CON 2 0” and “CON 2 1”. Press key number 4 with the display flashing the setting you wish to use. Press key number 1 to return to “CON 2”. Press key number 2 to scroll to “CON 3”.

CON 3 - Configuration Switch 3 - POS Message This code is used to disable the point of sale message. CON 3 0 = enabled, CON 3 1 = disabled. Press key number 4 and “CON 3 #” will be displayed, with the “#” flashing. Press key numbers 2 or 3 to scroll between “CON 3 0” and “CON 3 1”. Press key number 4 with the display flashing the setting you wish to use. Press key number 1 to return to “CON 3”. Press key number 2 to scroll to “CON 4”.

CON 4 - Configuration Switch 4 - Automatic Viewing of Historical Sales and Cash Accounting, ERROR or NONE

This code is used to enable viewing of historical sales, historical cash, ERROR or NONE automatically when the door is opened. To enable automatic viewing option enter “CON 4 1”; to disable enter “CON 4 0”. At “CON 4 0” ERROR or NONE automatically displays when the door is open. Press key number 4 and “CON 4 #” will be displayed, with the “#” flashing. Press key number 2 or 3 to scroll between “CON 4 0” and “CON 4 1”. Press key number 4 with the display flashing the setting you wish to use. Press key number 1 to return to “CON 4”. Press key number 2 to scroll to “CON 5”.

CON 5 - Configuration Switch 5 - Door Switch Reset Status This code is used to reset all resettable data when the door switch is cycled and at least one data register is read via the display when set at “CON 5 1” or to reset all resettable data only when the “RESET” command is received via handheld or portable computer when set at “CON 5 0”. Press key number 4 and “CON 5 #” will be displayed, with the “#” flashing. Press key numbers 2 or 3 to scroll between “CON 5 0” and “CON 5 1”. Press key number 4 with the display flashing the setting you wish to use. Press key number 1 to return to “CON 5”. Press key number 2 to scroll to “CON 6”.

Page 15

PROGRAMMING

of 90

CON 6 - Configuration Switch 6 - Reserved This code is reserved for future use. Press key number 2 to scroll to “CON 7”.

CON 7 - Configuration Switch 7 - Save Credit This code is used to determine how long a credit will be saved. C7 0 will save the credit for five minutes. CON 7 1 will save the credit indefinitely. Press key number 4 and “CON 7 #” will be displayed, with the “#” flashing. Press key number 2 or 3 to scroll between CON 7 0 and CON 7 1. Press key number 4 with the display flashing the setting you wish to use. Press key number 1 to return to “CON 7”. Press key number 2 to scroll to “CON 8”.

CON 8 - Configuration Switch 8 - Force Vend This code is used to determine escrow to select or escrow to price. CON 8 0 will set vender to escrow to select and CON 8 1 will set vender to escrow to price. Press key number 4 and “CON 8 #” will be displayed, with the “#” flashing. Press key number 2 or 3 to scroll between CON 8 0 and CON 8 1. Press key number 4 with the display flashing the setting you wish to use. Press key number 1 to return to “CON 8”. Press key number 2 to scroll to “CON 9”.

CON 9 - Configuration Switch 9 - Multi Vend This code is used to allow multiple vends without re-depositing funds. CON 9 0 will not allow multiple vends and CON 9 1 will allow multiple vends. Press key number 4 and “CON 9 #” will be displayed, with the “#” flashing. Press key number 2 or 3 to scroll between CON 9 0 and CON 9 1. Press key number 4 with the display flashing the setting you wish to use. Press key number 1 to return to “CON 9”. Press key number 2 to scroll to “CON 10”.

CON 10 - Configuration Switch 10 - Bill Escrow Inhibit This code is used to allow last bill that meets or exceeds maximum vend price to be held in escrow. CON 10 0 will escrow bill and CON 10 1 will not escrow bill (or stack the bill). Press key number 4 and “CON 10 #” will be displayed, with the “#” flashing. Press key number 2 or 3 to scroll between CON 10 0 and CON 10 1. Press key number 4 with the display flashing the setting you wish to use. Press key number 1 to return to “CON 1 0”. Press key number 2 to scroll to the next configuration code. Press key number 1 to return to “CONFIG”. Press key number 2 will scroll to next routine.

Page 16

PROGRAMMING

of 90

*”CHANGE” - CORRECT CHANGE ONLY CONTROL ROUTINE This function is used to allow consumer overpay, set a correct change value, and set an unconditional acceptance value. Press key number 4 will enter “CONOVER#”.

“CONOVERX” - Allow Consumer Overpay This function allows the vender to vend with the risk of not being able to return the full amount of change. This function has to be turned on to be able to allow consumer overpay. Press key number 4 and display will show “CONOVER#”, where “#” is flashing. CONOVER1 will allow consumer overpay (customer could potentially be shortchanged) and “CONOVER0” will not allow consumer overpay (will not allow customer to be shortchanged). Press key number 2 or 3 to scroll between CONOVER0 and CONOVER1. Press key number 4 with the display blinking the setting you wish to use. Display will return to “CONOVER#”. Press key number 2 to scroll to “CORR CHG”.

“CORR CHG” - Correct Change Value This is the function that the control board will use to set a value which will turn on the correct change indicator. Note: If “ACCEPT” is set, the “CORR CHG” should be equal to or less than the “ACCEPT”. Note: If the value set is 00.00, the correct change indicator will never come on. If the controller determines that it cannot return the exact amount of the correct change value or any value less than it, then the indicator will be turned on. Press key number 4 and the display will show “##.##’. Press key number 2 or 3 to scroll from 00.00 to 99.99. Press key number 4 with the display showing the value you wish to use. Display will return to “CORR CHG” Press key number 2 to scroll to “ACCEPT”.

“ACCEPT” - Unconditional Acceptance Value This is the function that the control board will use to set the largest value of any single form or currency (coin or bill) that can be accepted without having enough change to pay back the full amount. Press key number 4 and the display will show “##.##”. Press key number 2 or 3 to scroll from 00.00 to 99.95. Press key number 4 with the display showing the value you wish to use. Display will return to “ACCEPT”. Press key number 1 to return to “CHANGE”. Press key number 2 to scroll to next routine.

*”PREVIEW” - PREVIEW DATA PASSWORD ROUTINE This function is used to enable viewing of cash collected, product sales, and error codes without opening the door. To view the data the 4 digit password (4-2-3-1) must be entered. Once entered the “CASH”, “SALES”, “ERROR”, and “RETURN” menus are available from the front of the vender. To view, follow instructions for cash counter routine, sales counter routines, error routine and return.

To change “PREVIEW” password: At “PREVIEW” press key number 4, “####” (representing current four digit password) will show on display with the far left digit blinking. Press key number 2 to scroll to number desired for password. Press key number 4. The next digit will start blinking, press key number 2 to scroll to number desired for password. Press key number 4. Continue this process until all 4 digits are set. Then press key number 4 and the display will return to “PREVIEW” and the new password has been saved. Pressing key number 1 at anytime during this routine will return to “PREVIEW” with no changes to password occurring.

Press key number 2 to scroll to next routine.

Page 17

PROGRAMMING

of 90

*”LANGUAGE” - LANGUAGE ROUTINE This function is used to set the language that will be used for display messages. Note: This does not change the menu prompts. Press key number 4 and the display will show the language currently set in the controller. Press key number 2 or 3 to scroll through the languages available.

ENGLISH - English ITALIAN - Italian SLOVENE - Slovene FRENCH - French PORTUGES - Portuguese FINNISH - Finnish GERMAN - German SPANISH - Spanish NORWEG - Norwegian

With the language you wish to enter showing on the display, press key number 4. The display will return to “LANGUAGE”. Press key number 2 to scroll to next routine.

*”TIME” - TIME AND DATE SETTING ROUTINE This function is used to set the year, month, date, and hour (military 24 hour clock). Press key number 4 and “ENABLE X” will show on display.

“ENABLEX” - Time and Date Enable Routine Press key number 4 and ENABLE0 = disabled or ENABLE1 = enabled will show on display. Press key number 2 to scroll between ENABLE0 and ENABLE1. Press key number 4 with the display showing the setting you wish to use and display will return to “ENABLEX”. Press key number 2 to scroll to “YEAR”.

“YEAR” - Year Setting (00 to 99) Press key number 4 and the current year setting will show on display. Press key number 2 or 3 to change the last 2 digits of the year (00 to 99). Press key number 4 with the display showing the year you wish to use and display will return to “YEAR”. Press key number 2 to scroll to “MONTH”.

“MONTH” - Month Setting (01 to 12) Press key number 4 and the current 2 digit month setting will show on display. Press key number 2 or 3 to change the month (01 to 12). Press key number 4 with the display showing the month you wish to use and display will return to “MONTH”. Press key number 2 to scroll to “DATE”.

“DAY” - Day of Month Setting (1 to 31) Press key number 4 and the current 2 digit day of month setting will show on display. Press key number 2 or 3 to change the day of month (1 to 31). Press key number 4 with the display showing the day you wish to use and display will return to “DAY”. Press key number 2 to scroll to “HOUR”.

“HOUR” - Hour and Minute Setting (0000 to 2359) Press key number 4 and the current 4 digit hour and minute setting will be displayed (24 hour). The hour setting will be blinking to indicate it can be changed. Press key number 2 or 3 to change the hour setting. Press key number 4 to save and the minute setting will start blinking to indicate it can be changed. Press key number 2 or 3 to change the minute setting. Press key number 4 will save and return display to “HOUR”. Press key number 2 to scroll to “DST”.

Page 18

PROGRAMMING

of 90

“DST” - Daylight Saving Time Setting This function is used to set the preferred daylight savings time setting. Press key number 4 will display the current setting. Press key number 2 or 3 to scroll through the “DST” options listed:

- “OFF”, no daylight savings time changes made.

- “AUSTRAL”, Australian rules - Set forward 1 hour at 1:00 am on the first Sunday in October; Set backward 1 hour at 1:00 am on the last Sunday in March.

- “EUROPE”, European rules - Set forward 1 hour at 1:00 am on the last Sunday in March; Set backward 1 hour at 1:00 am on the last Sunday in October.

- “NAMERICA”, North American rules - Set forward 1 hour at 2:00 am on the first Sunday in April; Set backward 1 hour at 2:00 am on the last Sunday in October.

Press key number 4 with the display showing the setting you wish to use and display will return to “DST”. Press key number 1 to return to “TIME”. Press key number 2 to scroll to next routine.

*”LIGHTING” - LIGHTING CONSERVATION CONTROL ROUTINE (Con 2 Must Be Enabled - C2 1) This function is used to turn the lights off and on during certain periods of the day. Press key number 4 will enter “ENABLE X”.

“ENABLEX” - Lighting Conservation Control Enable Routine This function is used to disable Lighting Conservation Control “ENABLE0” (lights will be on at all times) or enable Lighting Conservation Control “ENABLE1” (lights can be set to turn off). Press key number 4 and the current “ENABLEX” setting will be displayed. Press key number 2 or 3 to scroll between “ENABLE0” and “ENABLE1”. Press key number 4 with the display showing the setting you wish to use. Press key number 2 to scroll to “STRT TIM”.

“STRT TIM” - Start Lighting Conservation Setting (lights off) This function is used to set the days and time to start light conservation when “ENABLE 1” is selected. Press key number 4 and “STRT DAY” will show on the display.

“STRT DAY” - Day to Start Setting This function is used to set the days of the week to start light conservation. Press key number 4 and “XXXXXX#” will show on the display, where XXXXXX will be the day of the week (i.e. MONDAY, TUEDAY, WEDDAY, THUDAY, FRIDAY, SATDAY, SUNDAY, EVRDAY) and # is 0 = disable, 1 = enable. With the display showing the day you wish to set press key number 4. The # will start blinking. Press key number 2 or 3 to scroll between “XXXXXX0” and “XXXXXX1”. Press key number 4 with the display showing the setting you wish to use. Display will return to “XXXXXX#”. Press key number 2 to scroll to the next day to set or press key number 1 to return to “STRT DAY”. Press key number 2 to scroll to “STRT HR”.

“STRT HR” - Start Hour and Minute Setting This function is used to set the hours to start light conservation (lamps off). Press key number 4 and “hhmm” will show on the display, where “hh” is the hour (military time) and “mm” is the minute. “hh” will be blinking, indicating the hour setting may be changed. Press key number 2 to scroll from 00 to 23. With the display showing the hour you wish to start light conservation, press key number 4. “mm” will start blinking, indicating the minute setting may be changed. Press key number 2 to scroll from 00 to 59. With the display showing the minute you wish to start light conservation, press key number 4. The display will return to “STRT HR”. Press key number 1 to return to “STRT TIM”. Press key number 2 to scroll to “STOP TIM”.

“STOP TIM” - Stop Light Conservation Setting (lights on) This function is used to set the days and time to stop light conservation. Press key number 4 and “STOP DAY” will show on the display.

“STOP DAY” - Day To Stop Setting This function is used to set the days of the week to stop light conservation and can be set in the same manner as Day to Start Setting.

Page 19

PROGRAMMING

of 90

“STOP HR” - Stop Hour and Minute Setting This function is used to set the hours and minutes to stop light conservation and can be set in the same manner as Start Hour and Minute Setting. Press key number 1 to return to “STOP TIM”. Press key number 1 to return to “LIGHTING”. Press key number 2 to scroll to next routine.

*”REFRIG” - REFRIGERATION ROUTINE This function is used to electronically control the refrigeration operations of the vender. Press key number 4 will enter “ENABLE X”.

“ENABLE X” - Energy Conservation Enable Routine This function is used to disable Energy Conservation “ENABLE 0” or enable Energy Conservation “ENABLE 1”. When enabled the cabinet temperature will be allowed to rise to the programmed storage level (“STORAGE”) during the following programmed time blocks. Press key number 4 and the current “ENABLE X” setting will be displayed. Press key number 2 or 3 to scroll between “ENABLE 0” and “ENABLE 1”. Press key number 4 with the display showing the setting you wish to use. Press key number 2 to scroll to “STRT TIM”.

“STRT TIM” - Start Energy Conservation This function is used to set the days and time to start Energy Conservation when “ENABLE1” is selected. Press key number 4 and “STRT DAY” will show on the display.

“STRT DAY” - Day to Start Setting This function is used to set the days of the week to start Energy Conservation. Press key number 4 and “XXXXXX#: will show on the display, where XXXXXX will be the day of the week (i.e. MONDAY, TUESDAY, WEDDAY, THUDAY, FRIDAY, SATDAY, SUNDAY, EVRDAY) and # is 0 = disable, 1 = enable. With the display showing the day you wish to set press key number 4. The # will start blinking. Press key number 2 or 3 to scroll between “XXXXXX0” and “XXXXXX1”. Press key number 4 with the display showing the setting you wish to use. Display will return to “XXXXXX#”. Press key number 2 to scroll to the next day to set or press key number 1 to return to “STRT DAY”. Press key number 2 to scroll to “STRT HR”.

“STRT HR” - Start Hour and Minute Setting This function is used to set the hours to start Energy Conservation. Press key number 4 and “hhmm” will show on the display, where “hh” is the hour (military time) and “mm” is the minute. “hh” will be blinking, indicating the hour setting may be changed. Press key number 2 to scroll from 00 to 23. With the display showing the hour you wish to start Energy Conservation, press key number 4. “mm” will start blinking, indicating the minute setting may be changed. Press key number 2 to scroll from 00 to 59. With the display showing the minute you wish to start Energy Conservation, press key number 4. The display will return to “STRT HR”. Press key number 1 to return to “STRT TIM”. Press key number 2 to scroll to “STOP DAY”.

“STOP TIM” - Stop Energy Conservation This function is used to set the days and time to stop energy conservation when “ENABLE 1” is selected. Press key number 4 and “STOP DAY” will show on the display.

“STOP DAY” - Day to Stop Setting This function is used to set the days of the week to stop energy conservation and can be set in the same manner as “STRT DAY” and “STRTHR”.

“STOP HR” - Stop Hour and Minute Settings This function is used to set the hours and minutes to stop energy conservation and can be set in the same manner as “START HR”. Press key number 1 to return to “STOP TIM”. Press key number 2 to scroll to “DEGREES”.

Page 20

PROGRAMMING

of 90

“DEGREES” - Degree Fahrenheit / Celsius Setting Routine This function is used to set the degree reading to Fahrenheit (DEGREESF) or Celsius (DEGREESC). Press key number 4 and “DEGREESX”, where the current setting (X) will be blinking. Press key number 2 or 3 to scroll between DEGREESF and DEGREESC. Press key number 4 with the display blinking the setting you wish to use. Press key number 1 to return to “DEGREES”. Press key number 2 to scroll to “SETPOINT”.

“SETPOINT” - Set Point Control Routine (Default Temperature 35.00 F / 1.50 C) This function is used to set the average product temperature for initial pull down and reload recovery. Press key number 4 and “tt.tx” will show on the display where x is F (Fahrenheit) or C (Celsius) and tt.t is the degrees. Press key number 2 to increase or 3 to decrease the number by 10 F or 0.50 C. With the display showing the set point temperature you wish to use, press key number 4. Press key number 2 to scroll to “STORAGE”.

“STORAGE” - Storage Setting Routine (Default Temperature 60.00 F / 15.50 C) This function is used to set the temperature for product storage and is used when Energy Conservation is enabled. Press key number 4 and “tt.tx” will show on display when X is F (Fahrenheit) or C (Celsius) and tt.t is the degrees. Press key number 2 to increase and 3 to decrease the number by 10 F or 0.50 C. With the display showing the storage setting you wish to use, press key number 4. Press key number 2 to scroll to “DISPLYX”.

“DISPLYX” - POS Temperature Display Enable Routine This function is used to enable the POS Temperature to be displayed following the “ICE COLD COCA COLA” POS message. Press key number 4 and “ DISPLYX” will show on the display where x is the current setting. With “X” blinking, press key number 2 or 3 to scroll between “DISPLY0” disabled or not displayed and “ DISPLY1” enabled or displayed. With the display showing the setting you wish to use, press key number 4. Press key number 1 to return to “REFRIG”. Press key number 2 to scroll to next routine.

*”SELBLCK1" - BLOCK SELECTION BANK 1 ROUTINE (CON 2 must be enabled - C2 1) This function is used to set selections which will be blocked during certain periods of the day. Press key number 4 will enter “ENABLE X”.

“ENABLEX” - Blocking Enable Routine This function is used to disable blocking “ENABLE0” or enable blocking “ENABLE1”. When enabled, active selections will not be allowed to vend on the days and times programmed. Press key number 4 and the current “ENABLE” setting will be displayed. Press key number 2 or 3 to scroll between “ENALBE0” and “ENABLE1”. Press key number 4 with the display blinking the setting you wish to use. Display will return to “ENABLEX”. Press key number 2 to scroll to “STRT TIM”.

“STRT TIM” - Start Selection Blocking Routine This function is used to set the day(s) and time to start selection blocking. Press key number 4 and “STRT DAY” will show on the display.

Page 21

PROGRAMMING

of 90

“STRT DAY” - Day of Week Start Setting This function is used to set the day(s) of the week to start selection blocking. Press key number 4 and “XXXXXX#” will show on the display, where XXXXXX will be the day of the week (i.e. MONDAY, TUEDAY, WEDDAY, THUDAY, FRIDAY, SATDAY, SUNDAY, EVR DAY) and # is 0 = disable, 1 = enable. With the display showing the day you wish to set press key number 4. The # will start blinking. Press key number 2 or 3 to scroll between “XXXXXX0” and “XXXXXX1.” Press key number 4 with the display showing the setting you wish to use. Display will return to “XXXXXX#’. Press key number 2 to scroll to the next day to set or press key number 1 to return to “STRT DAY”. Press key number 2 to scroll to “STRT HR”.

“STRT HR” - Start Hour and Minute Setting This function is used to set the hours and minutes to start selection blocking. Press key number 4 and “hhmm” will show on the display, where hh is the hour (military time) and mm is the minute. “hh” will be blinking, indicating the hour setting may be changed. Press key number 2 to scroll from 00 to 23. With the display showing the hour you wish to start selection blocking, press key number 4. “mm” will then start blinking, indicating the minute setting may be changed. Press key number 2 to scroll from 00 to 59. With the display showing the minute you wish to start selection blocking, press key number 4. The display will return to “STRT HR”. Press key number 1 to return to “STRT TIM”. Press key number 2 to scroll to “STOP TIM”.

“STOP TIM” - Stop Selection Blocking Routine This function is used to set the day(s) and times to stop selection blocking. Press key number 4 and “STOP DAY” will show on the display.

“STOP DAY” - Day of Week Stop Setting This function is used to set the days of the week to stop selection blocking and can be set in the same manner as Day of Week Start Setting.

“STOP HR” - Stop Hour and Minute Setting This function is used to set the hours and minutes to stop selection blocking and can be set in the same manner as Start Hour and Minute Setting. Press key number 1 to return to “STOP TIM”. Press key number 2 to scroll to “SELECT”.

“SELECT” - Selection To Be Affected By Blocking This function is used to set selection(s) which will be blocked during certain periods of the day. Press key number 4 and “SELA1#” will be displayed, where # is the current setting for the selection number displayed. 0 = disabled; 1 = enabled. Press key number 2 to scroll to the key number setting you desire to change. Press key number 4 with the key number showing you wish to change (i.e. SELA1#) and the # will start blinking. Press key number 2 or 3 to scroll between SELA1 0 and SELA1 1. Press key number 4 with the display showing the setting you wish to use. Display will return to SELA1#. Press key number 1 to return to “SELECT”. Press key number 2 to scroll to “LIGHT”.

Page 22

PROGRAMMING

of 90

“LIGHTX” - Lighting / P.O.S. Display Control This function is used to turn the lights (if supported) and P.O.S. Display Message off during selection blocking period 1. 0 = disable or on; 1 = enable or off. Press key number 4 and the “#” will start flashing. Press key number 2 or 3 to scroll between “LIGHT0” and “LIGHT1”. Press key number 4 with the display showing the setting you wish to use. Display will return to “LIGHTX”. Press key number 1 to return to “SELBLCK1”. Press key number 2 to scroll to “SELBLCK2”.

*”SELBLCK2" - BLOCK SELECTION BANK 2 ROUTINE This function is a second set used to set selection(s) which will be blocked during certain periods of the day. Press key number 4 will enter “ENABLEX”.

“ENABLEX” - Blocking Enable Routine. Set this function using instruction for “ENABLEX” in “SELBLCK1”.

“STRT TIM” - Start Selection Blocking Routine This function is used to set the day(s) and times to start selection blocking. Press selection button 4 and “STRT DAY” will show on the display.

“STRT DAY” - Day of Week Start Setting Set this feature using instructions for “SELBLCK1”, “STRT TIM”, “STRT DAY”.

“STRT HR” - Start Hour and Minute Setting Set this function using instructions for “SELBLCK1”, “STRT TIM”, “STRT HR”.

“STOP TIM” - Stop Selection Blocking Routine. This function is used to set the day(s) and times to stop selection blocking. Press key number 4 and “STOP DAY” will show on the display.

“STOP DAY” - Day of Week Stop Setting Set this function using instructions for “SELBLCK1”, “STOP TIM”, “STOP DAY”.

“STOP HR” - Stop Hour and Minute Setting Set this function using instructions for “SELBLCK1”, “STOP TIM”, “STOP HR”. Press key number 1 to return to “STOP TIM”. Press key number 2 to scroll to “SELECT”.

“SELECT” - Selection To Be Affected By Blocking This function is used to set selection(s) which will be blocked during certain periods of the day. Set this function using instructions for “SELBLCK1”, “SELECT”. Press key number 1 to return to “SELECT”. Press key number 2 to scroll to “LIGHTX”.

“LIGHTX” - Lighting / P.O.S. Display Control This function is used to turn the lights (if supported) and P.O.S. Display Message off during selection blocking period 2. Set this function using instructions for “SELBLCK1”, “LIGHT”. Press key number 1 to return to “SELBLCK2”. Press key number 2 to scroll to “DISCOUNT”.

Page 23

PROGRAMMING

of 90

*”DISCOUNT” - DISCOUNT SETTING ROUTINE This function is used to set the day(s) and times to allow discount prices. Press key number 4 and ENABLE X will show on the display.

“ENABLE X” - Discount Setting Enable Routine This function is used to disable discounting “ENABLE 0” or enable discounting “ENABLE 1”. Press key number 4 and the current “ENABLE X” setting will be displayed. Press key number 2 or 3 to scroll between “ENABLE 0” and “ENABLE 1”. Press key number 4 with the display blinking the setting you wish to use. Display will return to “ENABLE X”. Press key number 2 to scroll to “STRT TIM”.

“STRT TIM” - Start Discount Pricing This function is used to set the day(s) and times to start discount prices. Press key number 4 and “STRT DAY” will show on the display.

“STRT DAY” - Day of the Week Start Setting Set this feature using instructions for “SELBLCK1”, “STRT TIM”, “STRT DAY”.

“STRT HR” - Start Hour and Minute Settings Set this feature using instructions for “SELBLCK1, “STRT TIM”, “STRT HR”.

“STOP TIM” - Stop Discount Pricing This function is used to set the day(s) and times to stop discount prices. Press key number 4 and “STOP DAY” will show on the display.

“STOP DAY” - Day to Stop Setting Set this feature using instructions for “SELBLCK1”, “STOP TIM”, “STOP DAY”.

“STOP HR” - Stop Hour and Minute Setting Set this function using instructions for “SELBLCK1”, “STOP TIM”, “STOP HR”.

“SELECT” - Selection Affected by Discount Pricing This function is used to set selection(s) which will be affected by discount prices. Press key number 4 and “SEL A1 #” will be displayed, where # is the current setting for the selection number displayed. 0 = disabled, 1 = enabled. Press key number 2 to scroll to the key number you desire to change. Press key number 4 with the key number showing you wish to change (i.e. SELA1 #) and the # will start blinking. Press key number 2 or 3 to scroll between “SELA10” and “SELA11”. Press key number 4 with the display showing the setting you wish to use. Display will return to “SELA11”. Press key number 1 to return to “SELECT”. Press key number 2 to scroll to “LESS AMT”.

“LESS AMT” - Discount Amount (Price) This function is used to set the discount amount (price) for selection(s) and times set. Press key number 4 and “##.##” will be displayed, where “##.##” is the current discount price that is set. Press key number 2 or 3 to change the price (00.00 to 99.99). Press key number 4 with the display showing the price setting you wish to use. Display will show price. Press key number 1 to return to “LESS AMT”. Press key number 1 to return to “DISCOUNT”. Press key number 2 to scroll to “OVERRIDE”.

Page 24

PROGRAMMING

of 90

“OVERRIDE” - MANUAL SWITCH OVERRIDE ROUTINE

This function is used to allow a key switch to override some of the settings stored for normal operations. This function can be programmed to control one or several of the following features: Free Vend Enable, Selection Blocking, Discount Pricing, and Lighting Control. Press key number 4 and the display will show “FREE X”. Press key number 2 or 3 to scroll through the override routines available. Press key number 1 to return to “OVERRIDE”.

“FREE X” - Free Vend Enable Routine This function is used to set the vender to free vend. 0 = disable, 1 = enable. Press key number 4 and “#” will start flashing. Press key number 2 or 3 to scroll between “FREE 0” and “FREE 1”. Press key number 4 with the display blinking the setting you wish to use. Display will return to “FREE X”. Press key number 2 to scroll to “NO VENDX”.

“NOVEND X” - No Vend (Vend Override) Enable Routing This function is used to set vender selections to not be allowed to vend and a “NO SALE” message to be displayed. 0 = disable, 1 = enable. Press key number 4 and “#” will start flashing. Press key number 2 or 3 to scroll between NOVEND 0 and NOVEND 1. Press key number 4 with the display showing the setting you wish to use. Display will return to “NOVEND X”. Press key number 2 to scroll to “BLOCKX”.

“BLOCK X” - Selection Blocking Override Routine This function is used to override “SELBLCK1” and “SELBLCK2” if they are being used. “BLOCK 0” is disabled, “BLOCK 1” is enabled. Press key number 4 and “#” will start flashing. Press key number 2 or 3 to scroll between “BLOCK 0” and “BLOCK 1”. Press key number 4 with the display blinking the setting you wish to use. Display will return to “BLOCK X”. Press key number 2 to scroll to “DISC X”.

“DISC X” - Discounting Override Routine This function is used to override “DISCOUNT” if it is being used. “DISC 0” is disabled and “DISC 1” is enabled. Press key number 4 and “#” will start flashing. Press key number 2 or 3 to scroll between “DISC 0” and “DISC 1” Press key number 4 with the display showing the setting you wish to use. Display will return to “DISC X”. Press key number 2 to scroll to “LIGHT X”.

“LIGHT X” - Lighting Control Override Routine This function is used to override “LIGHT’” if it is being used. “LIGHT 0” is disabled and “LIGHT 1” is enabled. Press key number 4 and “#” will start flashing. Press key number 2 or 3 to scroll between “LIGHT 0” and “LIGHT 1”. Press key number 4 with the display blinking the setting you wish to use. Display will return to “LIGHT X”. Press key number 2 to scroll to “REFRIG X”.

Page 25

PROGRAMMING

of 90

“REFRIG X” - Refrigeration Control Override Routine This function is used to override “REFRIG”, if it is being used. “REFRIG 0” = disabled and “REFRIG 1” = enabled. Press key number 4 and “#” will start flashing. Press key number 2 or 3 to scroll between “REFRIG 0” and “REFRIG 1”. Press key number 4 with the display showing the setting you wish to use. Display will return to “REFRIG X”. Press key number 1 to return to “OVERRIDE”. Press key number 2 to scroll to “RVNDMECH”.

“RVNDMECH” - REMOTE VEND MECHANISM ROUTINE This function is used to activate the Universal Satellite Device Control routine. Press key number 4 to enter routine. If the controller detects a device responding to the remote vend mechanism address (USD address #3,50H), the vend request commands for this device will be controlled by the following parameters.

“STRT TIM” - Start Time Setting Routine This function is used to set the day(s) and time to start the routine. Press key number 4 and “STRT DAY” will show on the display.

“STRT DAY” - Day of week to start setting Set this feature using instructions for “SELBLCK1”, “STRT TIM”, “STRTDAY”.

“STRT HR” - Start hour and minute settings Set this feature using instructions for “SELBLC1”, “STRT TIM”, “STRT HR”.

“STOP TIM” - Stop Time Setting Routine This function is used to set the day(s) and time to stop the routine. Press key number 4 and “STOP DAY” will show on the display.

“STOP DAY” - Day of week to stop setting Set this feature using instructions for “SELBLCK1”, “STOP TIM”, “STOP DAY”.

“STOP HR” - Stop hour and minute settings Set this feature using instructions for “SELBLCK1”, “STOP TIM”, “STOP HR”.

“SELECT” - Selection Setting Routine This feature is used to set the selection(s) which will be affected by the Remote Vend Mechanism routine. Press key number 4 and “SEL A1 #” will be displayed, where # is the current setting for the selection number displayed. 0 = disabled, 1 = enabled. Press key number 2 to scroll to the select button number you desire to change. Press key number 4 with the select button number showing you wish to change (i.e. SEL A1 #) and the # will start blinking. Press key number 2 or 3 to scroll between “SEL A1 0” and “SEL A1 1”. Press key number 4 with the display showing the setting you wish to use. Display will return to “SEL ## #”. Press key number 1 to return to “SELECT”. Press key number 2 to scroll to “VND RATE”.

Page 26

PROGRAMMING

of 90

“VND RATE” - Universal Satellite Device (USD) Vend Rate Routine This function is used to set the vend rate (0-255). Press key number 4 and the current vend rate (0-255) will show on the display. Press key number 2 to increase, or 3 to decrease the number in single digit increments. NOTE: A rate of “0” disables the USD. All other rates, #, will cause a vend command every #’th local vend. Press key number 4 with the display showing the vend rate you wish to use and the display will return to “VND RATE”. Press key number 1 to return to “RVNDMECH”. Press key number 2 to scroll to “RETURN”.

“GRABMODE” - GRABMODE SETTING ROUTINE

This function is used to set the Grabmode. When enabled, this mode will vend one time from a column and cancel credit. Press key number 4 and “ENABLEX” will show on display. Press key number 4 and the current “GRABMODE” setting will show on the display (ENABLE0 or ENABLE1) with the “0” or “1” blinking. Press key number 2 or 3 to toggle between “ENABLE1” and “ENABLE0”. ENABLE1 means GRABMODE is turned on and credit will cancel when a column’s vend mech cycles. ENABLE0 means GRABMODE is disabled and the vender will cancel credit upon product delivery through the delivery door. This function is set at “ENABLE 0” from the factory. Press key number 4 with the display showing the GRABMODE setting you wish to use and the display will return to “ENABLEX”. Press key number 1, display will return to “GRABMODE”. Press key number 2 to scroll to “RETURN”.

HEALTH” – HEALTH SETTING ROUTINE

This function is used to enable the health protection feature for product when needed. When enabled it operates as follows:

1. Cabinet temperature must be maintained at 41 degrees F (5 degrees C) or below for product to be vended while in normal operation. If the cabinet temperature exceeds 41 degrees F, and fails to return to 41 degrees F or below for 15 minutes the controller will issue a “HCOD” error and disable vending of health protected products.

2. After door closure, (refill or service) the machine has 30 minutes to pull down to 45 degrees F (7 degrees C). If the machine has not reached 45 degrees F (7 degrees C) after 30 minutes the controller will issue a “HTIN” error. Once a health time error is activated the controller will not allow product to be delivered. After 30 minutes if the temperature is 45 degrees F or less, but not 41 degrees F the controller will set a 15 minute timer. During this time, if the cabinet temperature falls below 41 degrees F (5 degrees C) the controller will allow health guarded product to be delivered. If the temperature doesn’t fall below 41 degrees F (5 degrees C) the controller will issue a “HCOD” error and disable vending of health protected products.

3. Power loss for 30 minutes or longer will result in automatic “HCOD” error activation and disable vending of health protected products upon power up.

4. Power loss less than 30 minutes. Once the machine regains power, if the cabinet temperature is 45 degrees F (7 degrees C) or less the controller will allow product to be dispensed. The controller will allow an additional 15 minutes for the temperature to pull down to 41 degrees F (5 degrees C). If the temperature doesn’t reach 41 degrees F (5 degrees C) or less after the 15 minute period the controller will issue a “HCOD” error and disable vending of health protected products. If the temperature is greater than 45 degrees F (7 degrees C) on power up the controller will automatically set a “HCOD” error and disable vending of health protected products.

5. Power loss less than 15 minutes. On power up the controller will allow vending. If the cabinet temperature doesn’t reach 41 degrees F (5 degrees C) or less in 15 minutes the controller will issue a “HCOD” error and disable vending of health protected products.

Page 27

PROGRAMMING

of 90

To enable, with “HEALTH” on display press key number 4 will enter “ENABLE X”. “ENABLE X” – Health Enable Routine

This function is used to enable the Health Protection feature. When enabled, protected selections will only be allowed to vend if health constraints listed above are met. Press key number 4 and the current “ENABLE” setting will be displayed. Press key number 2 or 3 to scroll between “ENABLED 0” and “ENABLED 1”. Press key number 4 with the display blinking the setting you wish to use. Display will return to “ENABLED X”. Press key number 2 to scroll to “SELECT”.

“SELECT” – Selection(s) To Be Affected By Health Protection

This function is used to set selection(s) which will be protected by the Health Protection constraints. Press key number 4 and “ALL SELECTS” will be displayed. Press key number 2 to scroll through “ALL SELECTS, A, B, C, D, and E”. Press key number 4 with the setting you wish to enter. Selecting “A, B, C, D, or E” will allow you to chose settings for that tray. Example: With “A” showing on display press key number 4. Display will show “A ALL SELECTS #”, press key number 2 to scroll through “A ALL SELECTS #, SEL A1 #, SEL A2 #, SEL A3 #, etc… With the setting you wish to change press key number 4 and the # will start blinking. Press key number 2 to scroll between “0” disabled and “1” enabled. With the setting you wish to use showing on the display press key number 4. Display will return to “A ALL SELECTS # or SEL A# #”. Press key number 1 to return to “SELECT”. Press key number 2 to scroll to “RECHECKX”

“RECHECKX” – Recheck Feature This function is used to allow an additional 45 minute period to bring the cabinet temperature down to 41 degrees F (7 degrees C). When this feature is enabled it will operate as follows: After a “HtIn” error has been issued (i.e. the cabinet temperature has not dropped below 45 degrees F in 30 minutes). The controller will perform 3 rechecks of the temperature in the next 45 minute period. Rechecks will occur in 15 minute intervals. During this period the controller will not allow vending to occur on health guarded selections.

1. If the cabinet temperature reaches 41 degrees F (5 degrees C) or less during this time the “HtIn” error will be cleared. The controller will allow health guarded product to be delivered.

2. If after the 3rd recheck period the temperature is greater than 41 degrees F (5 degrees C). The controller will clear the “HtIn” error, set the “RCHE” error and vending health guarded products will continue to be disabled.

3. If during the recheck period, any temperature reading that is greater than the previous reading (a trend leading in the upwards direction) will result in clearing the “HtIn” error, setting the “RCHE” error and vending health protected products will continue to be disabled.

“RETURN” - RETURN TO SALES MODE Press key number 4 will exit Service Mode and return to Sales Mode.

Page 28

PROGRAMMING

of 90

COCA-COLA PROGRAMMING METHOD

QUICK REFERENCE MENU PROMPTS

Select Button 1: Abort / Cancel (will return to previous menu prompt or to normal door open mode) Select Button 2: Scroll Up (forward in menu) Select Button 3: Scroll Down (backward in menu) Select Button 4: Enter / Save / Clear (allows you to enter a specific prompt, save what you have programmed, or clear the

error prompts)

**ERROR - Error Readout Routine

** VENDMECH - Vend Mechanism Error

COLJAM# - Column Jam

**CONTROL - Control System Error

DOORSWIT - Door Switch RAM ERR - Board Check Sum AC LOW - Voltage Low SCALEER - Scale Factor

**SELECTSW - Select Switch Error

SELSW# - Select Switch

**CHANGER - Changer Error

COINCOMM - Changer Communication TUBESENS - Tube Sensor COININLE - Inlet Chute Blocked TUBJAM# - Tube Jam COINROM - Changer ROM EXCESSES - Excessive Escrow Attempt COINJAM - Coin Jam Coin Mech LOWACCEP - Low Coin Accept Rate ACCDISCN - Acceptor Unplugged ROUTING - Coin Mis-Routed

**BILLVAL - Bill Validator Error

BILLCOMM - Validator Communication BILL FULL - Stacker Full BILL MOT - Defective Motor BILL JAM - Bill Jam BILL ROM - Check Sum BILL OPEN - Open Stacker BILL SENS - Validator Sensor

**CARD RDR - Card Reader Error

CARDCOMM - No Reader Communication CARD# - Failed Reader

**ONLINE - Online Module Error

ONLINE - No Communication ONL COMM - Network Not Responding ONL INTL - Internal Online Problem

**RVEND - Remote Vend Mechanism Error

RV COMM# - No Communication RVEND# # - Indicates Error Code

**SEL/DISP - Selection / Display Device Error

S/D COMM - No Communication

**REFRIG - Refrigeration Error

TEMPSENS - Temp Sensor Bad TOO COLD - 30 Below Lower Limit TOO HOT - 30 Above Lower Limit

** Prompts listed with asterisks are the only programs accessible coming from the factory. If other programs are desired,

they need to be turned on in the machine configuration code programs. Note: To enter “AUTO”, at the “PASS” prompt, enter the correct password to enter Auto Test.

CONFIG: Machine Configuration CON 1 Single Price / Multi Price

CON 2 Optional Features CON 3 POS Message CON 4 Auto View SALES and CASH CON 5 Door Switch Reset CON 6 Reserved CON 7 Save Credit CON 8 Force Vend CON 9 Multi Vend CON 10 Bill Escrow

**COINPAYO - Coin Payout Mode **TUBEFILL - Tube Fill Mode **TESTMODE - Test Routine

**PASSWORD - Password **CASH - Cash Counter Routine

**SALES - Sales Counter Routine

**PRICE - Price Setting Routine **STS PROG - Space-To-Sales Settings

**CONFIG - Machine Configuration

CHANGE - Correct Change Settings PREVIEW - Password Setting LANGUAGE - Language Setting TIME - Time and Date Setting LIGHTING - Light Conservation Setting REFRIG - Energy Conservation Setting SELBLCK1 - Select Blocking Settings SELBLCK2 - Select Blocking Settings DISCOUNT - Discount Price Settings OVERRIDE - Manual Switch Override Setting RVEND - Remote Vend Mech Setting GRABMODE - Grabmode Setting HEALTH - Health Protection Feature RETURN - Return

NO COOL - Failed System

**DNC ERR - Dixie-Narco Corporation Errors

MB COMM - Machine Board No Communication ELEVATOR - Elevator Failed CONVEYOR - Conveyor Failed PORT DR - Switch Bad

**HEALTH - Health Timer Errors

HTIN - Health Timer Error HCOD - Health Code Error RCHE - Recheck Error

TESTVEND - Vend Testing TEST SEL - Select Switch Test DISPLAY - Display Test RELAYS - Relay Test

CASH/######## - Historical Cash Counter / Vender CARD/######.## - Historical Card Reader Cash Counter

SALES/######## - Historical Vend Counter/Vender COL A1/####/#### - Resettable Vend Counter/Select

PR# - Price For Each Selection

CON# (# = 1 thru 10) CON#0 (off) (see below) CON#1 (on)

Page 29

GENERAL MAINTENANCE

of 90

The most important facets of proper care and maintenance of your machine are the electrical power supplied to it, leveling, and cleanliness of the machine.

POWER

The machine must be connected to a dedicated 120 VAC, 15 Amp circuit (U.S. and Canada).

CAUTION:

REMOVE POWER TO THE AC DISTRIBUTION

BOX WHEN ANY ELECTRICAL COMPONENTS

ARE CONNECTED / DISCONNECTED FOR

TESTING OR REPLACEMENT.

CLEANING

DO NOT USE A WATER JET OR NOZZLE TO CLEAN THE VENDER

GLASS DOOR

The display glass should be cleaned inside and out with paper towels and glass or non-abrasive all-purpose cleaner. The gasket around the product door should be wiped down using warm water, any mild general purpose, non-abrasive cleaner and a soft towel. Never lubricate the gasket and always check for cracking or deformities which may cause leaks. Replace if necessary.

TRAYS / TRAY INSERTS

The trays and tray inserts should be cleaned periodically using warm water and a mild general purpose, non-abrasive cleaner. Care should be taken to ensure water does not enter the solenoids. DO NOT USE SOLVENTS OR

ABRASIVE MATERIALS TO CLEAN ANY PORTION OF THE TRAY.

SLIDE/PUSHER ASSEMBLY

The slide/pusher assembly should be cleaned periodically using warm water and any mild general-purpose non-abrasive cleaner. After drying, the slide assembly needs to have a coat of Armorall applied. Care should be taken to ensure liquid does not enter solenoids. DO NOT

USE SOLVENTS OR ABRASIVE MATERIALS TO CLEAN ANY PORTION OF THE TRAY.

CABINET

Wash the cabinet with a good detergent or soap mixed in warm water. Wax the vender often with a good grade of automobile wax. Any corrosion inside the vender should be removed with fine steel wool and the area should be painted with white paint.

Repair any scratches on painted surfaces to prevent corrosion.

DRAIN PAN

Check the drain pan periodically for dirt, debris, and proper alignment. Clean as needed. Ensure nothing obstructs the drain tube and drain hose.

WARNING THE COMPRESSOR ELECTRICAL CIRCUIT IS ALWAYS LIVE WHEN THE PLUG IS CONNECTED TO AN ELECTRICAL OUTLET.

REFRIGERATION CONDENSER

Clean the condenser periodically of dirt or lint build-up. Remove the build up with a brush or vacuum, or blow the dirt out of the condenser with compressed air and approved safety nozzle. Ensure nothing obstructs air intake at the bottom of the main door. Ensure nothing obstructs air exhaust at the rear of the cabinet.

COIN ACCEPTOR

Follow the Coin Acceptor Manufacturer’s instructions.

LUBRICATING THE VENDER

The vender refrigeration system does not require any field lubrication. The hermetic refrigeration system and fan motors are manufactured with lifetime lubrication.

EPROM REPLACEMENT

Software changes / upgrades are accomplished by changing the EPROM on the Control Board.

To change EPROM: Remove power to the AC Distribution Box. Remove existing EPROM. Replace the EPROM. (The EPROM’s legs bend easily. Remove and replace very carefully.) Note the alignment notch at one end of the EPROM and on the control board. The notches must be matched or problems will occur. Appy power to the AC distribution box. Display will scroll “*/SOFTWARE/REV###.##/ICE COLD COCACOLA/##.##”. (SEE PAGE 81 FOR EPROM LOCATIONS)

Page 30

MAJOR COMPONENT DESCRIPTION

of 90

MAJOR COMPONENT DESCRIPTION

AC DISTRIBUTION BOX

110 VAC

15 Amp Outlet (110 VAC) Provides power to refrigeration unit.

Transformer (T1) Provides 24 Volt

and 12 Volt (center tap) power to the Controller Board.

Fuse (Top) 10 Amp, 32 Volt,

SloBlo; protects 24 Volt input to Controller Board from secondary of T1.

Fuse (Bottom) 2 Amp, SloBlo;

protects 12 Volt input to Controller Board from secondary, center tap of T1.

Varistor Across incoming

AC power to remove large power spikes.

Choke (Domestic) Foster A-16015-01 5mH 6A.

Choke (Export) Foster A-160405 5mH 6A (220Volts)

REFRIGERATION UNIT

110 VAC

Compressor Aspera, 1/2 HP, 115 VAC,

60 Hz, 1 Phase T6213Z Unit uses 13 oz. of 134A refrigerant

Start Relay 110 VAC - T1 9660-041-180 Double Pole, 115 VAC

Start Capacitor 110 VAC - 189227 Thermal Overload 110 VAC - T1 MST16AFN-

3001

Condenser Fan 16W Motor 110 VAC FV100CW25S Blade - 10” dia.

Evaporator Fan Motor 110 VAC - SPGE9HBV1 Blade - 8” dia.

Page 31

MAJOR COMPONENT DESCRIPTION

of 90

UNIVERSAL (KO) BOARD (0077-8272CB & Higher)

Page 32

PROGRAMMING

of 90

UNIVERSAL (KO) BOARD (prior to 0077-8272CB)

Page 33

PROGRAMMING

of 90

MACHINE BOARD (0077-8272CB and Higher)

Page 34

PROGRAMMING

of 90

MACHINE BOARD (prior to 0077-8272CB)

Page 35

MAJOR COMPONENT DESCRIPTION

of 90

WIRING DIAGRAM (9 Column)

Page 36

PROGRAMMING

of 90

Wiring Diagram (6 Column)

Page 37

TROUBLESHOOTING

of 90

AC DISTRIBUTION BOX T8

1 Thread stud 2 Hex Nut 3 Side Panel Ground 4 Chassis 5 Ground Lead from

Power Input 6 Toothed Terminal 7 Panel Mount

Receptacle Ground 8 Choke

1 Thread stud

2 Hex Nut 3 Side Panel Ground 4 Chassis 5 Ground Lead from

Power Input 6 Toothed Terminal 7 Panel Mount

Receptacle Ground

AC DISTRIBUTION BOX NON-T8

Page 38

TROUBLESHOOTING

of 90

Troubleshooting

ASD DISPLAY

Page 39

TROUBLESHOOTING

of 90

CONTROL BOARD ISSUES

Page 40

TROUBLESHOOTING

of 90

CONTROL BOARD ISSUES (CONTINUED)

Page 41

TROUBLESHOOTING

41 of 90

CONTROL BOARD ISSUES (CONTINUED)

Page 42

TROUBLESHOOTING

of 90

CONTROL BOARD ISSUES (CONTINUED)

Page 43

TROUBLESHOOTING

of 90

COIN MECH ISSUES

Page 44

TROUBLESHOOTING

of 90

COIN MECH ISSUES (CONTINUED)

Page 45

TROUBLESHOOTING

of 90

COIN MECH ISSUES (CONTINUED)

Page 46

TROUBLESHOOTING

of 90

COIN MECH ISSUES (CONTINUED)

Page 47

TROUBLESHOOTING

of 90

COMPRESSOR ISSUES

Page 48

TROUBLESHOOTING

of 90

COMPRESSOR ISSUES (CONTINUED)

Page 49

TROUBLESHOOTING

of 90

SOLENOIDS

Page 50

TROUBLESHOOTING

of 90

SOLENOIDS (CONTINUED)

Page 51

TROUBLESHOOTING

of 90

CONVEYOR ISSUES

Page 52

TROUBLESHOOTING

of 90

Open and close

the port door.

Does the port

door close completely?

Display reads vending but the elevator does not

Clear the

obstruction and

retest with service

door open.

move.

Check port door

switch.

YES

Correct or replace

port frame and

Is port door switch properly secured?

retest.

Does elevator

function?

YES

Finished.

YES

Replace port

door switch.

Check harness connection and

VMC.

Is harness

connected at VMC

Connect

harness and

retest.

Replace elevator

motor harness and

retest.

Does the elevator

run?

Open glass door and depress the

P.I. Switch and

test vend one

selection.

Did elevator motor

run?

Did the elevator

make any noise?

Finished.

Close the door

YES

and retest.

Did the elevator

belt try to run

backwards?

Check the home sensor

switch connections.

YES

Check for obstructions

under the conveyor and

retest.

Did the elevator

motor move?

Replace elelvator motor and retest.

Replace P.I.

switch and retest.

Finished.YES

Did elevator motor

run?

Replace lower

limit switch

harness.

Did elevator run?

YES

Replace VMC

and retest.

Finished.YES

ELEVATOR ISSUES

(including upper / lower limit switches & port door)

Page 53

TROUBLESHOOTING

of 90

FAN MOTOR ISSUES

Page 54

TROUBLESHOOTING

of 90

KEYPAD ISSUES

Page 55

TROUBLESHOOTING

of 90

KEYPAD ISSUES (CONTINUED)

Page 56

TROUBLESHOOTING

of 90

LIGHT ISSUES

Page 57

TROUBLESHOOTING

of 90

LIGHT ISSUES (CONTINUED)

Page 58

TROUBLESHOOTING

of 90

TEMP SENSOR ISSUES

Page 59

TROUBLESHOOTING

of 90

CONDENSATE ON OUTSIDE OF PRODUCT DOOR

ICE / FROST ON EVAPORATOR

COMPRESSOR RUNS CONTINUOUSLY

Page 60

PARTS

of 90

PARTS INDEX

Machine Front View ............................................................................. pgs. 61 & 62

Cabinet Detail ...................................................................................... pgs. 63 & 64

Service Door (Front) ............................................................................. pgs. 65 & 66

Service Door (Inside) ........................................................................... pgs. 67 & 68

Tray Assembly ..................................................................................... pgs. 69 & 70

AC Distribution Box .............................................................................. pgs. 71 & 72

Elevator................................................................................................. pgs. 73 & 74

Conveyor............................................................................................... pgs. 75 & 76

Lighting.................................................................................................pgs. 77 & 78

Refrigeration ......................................................................................... pgs. 79 & 80

Electronics ............................................................................................ pgs. 81 & 82

Harnesses........................................................................................................pg. 83

Labels/Decals/Misc..........................................................................................pg. 84

Screws & Nuts .............................................................................. pgs. 85, 86, & 87

Washers/Bolts/Misc. Hardware ..................................................... pgs. 88, 89, & 90

Page 61

PARTS

of 90

MACHINE FRONT VIEW

Page 62

PARTS

of 90

MACHINE FRONT VIEW

ITEM DN5000 PART # DN3000 PART # PART DESCRIPTION

1A-1 800,102,29x.x1 800,102,40x.x1 Glass Door, 2 Pane (001-8250 and higher) 1A-2 800,101,87x.x1 NA Glass Door, 2 Pane (prior to 001-8250) 1B-1 800,102,36x.x1 800,102,38x.x1 Glass Door, Special 3 Pane (001–8250 and higher)

1B-2 800,102,02x.x1 NA Glass Door, Special 3 Pane (prior to 001–8250) 1C–1 626,055,30x.x3 800,102,33X.X1 Glass Door, Special Film 2 Pane Special (001–8250 and higher) 1C–2 800,102,12x.x1 NA Glass Door, Special Film 2 Pane Special (prior to 001–8250)

2 801,814,58x.x1 TBD Gasket, Glass Door

3A 801,306,49x.x1 SAME Top Hinge, Glass Door – Horizontal Mounting (001-8250 and

higher)

3B 801,306,48x.x1 NA Top Hinge, Glass Door - Horizontal Mounting (001-8152 to 001-

8250) 3C 801,305,70x.x1 NA Top Hinge, Glass Door (prior to 001-8152) 3D 800,303,56x.x1 SAME Top Hinge Screws ¼ - 20 (001-8152 and higher) 3E 800,303,41x.x1 NA Top Pivot Pin, Glass Door (prior to 001-8152) 3F 801,814,52x.x1 SAME Plastic Shoulder Bushing (Pike Glass Door) 4A 801,305,65x.x1 SAME Leg, Cabinet Base

4B-1 900,502,49x.x1 SAME 4B-2 800,503,38x.x1 SAME Leveling Leg Japan (not shown)

4C 805,410,96x.x1 SAME Skid Board (not shown)

5 W334 SAME Top Hinge, Service Door 6A 432,052,50x.x4 SAME Nut Retainer Housing Assembly 6B 432,050,73x.x3 SAME Nut Retainer Housing 6C 801,303,85x.x1 SAME Cage Nut 6D 900,801,06x.x1 SAME Square Nut, ½-13 6E 900,301,97x.x1 SAME Screw, Phil Pan #8-32x1/4 6F 900,302,01x.x1 SAME Screw, Hex ¼-20x5/8

7 626,030,19x.x3 SAME Storage Shelf Panel

8 804,400,51x.x1 SAME Ballast Assembly (SP-3) 9A 801,401,88x.x1 SAME Loading Platform (not shown) 9B 626,050,21x.x3 SAME Support Bracket, Loading Rack 9C 626,050,37x.x3 SAME Latch, Loading Rack (not shown)

10A 626,020,26x.x3 636,020,07x.x3 Bottom Skirt

10B 800,303,38x.x1 SAME Screw, Truss AB #8 - 18 x 1/2

11 801,813,13x.x1 SAME Condenser Intake Guard 12 800,303,37x.x1 SAME Screw, Phil Pan ¼-20x3/4L (prior to 001-8152) 13 900,800,67x.x1 SAME Keps Nut ¼-20 14 627,020,60x.x4 SAME Lag Bracket Kit (see Tech Bulletin 344)

15A 626,060,00x.x3 636,060,20x.x3 15B 626,060,30x.x3 TBD 16A 626,020,39x.x4 SAME Harvest Unit Installation Hardware Kit 16B 626,030,28x.x3 SAME Harvest Bracket

17 W766 SAME Carriage Bolt, ¼-20 18 626,020,42x.x3 SAME Right Security Angle

19A 800,503,33x.x1 SAME Bottom Service Door Hinge (001-8191 and higher) 19B 800,801,28x.x1 SAME Nut, Jam (001-8191 and higher) 19C 800,902,68x.x1 SAME Sleeve, Anti-Vandal (001-8191 and higher) 20A 626,052,70x.x4 SAME Kit, Vandal Plate, Vac Form (Service Part) (prior to 001-8152) 20B 805,701,91x.x1 SAME Vandal Plate Injection Molded (001-8152 and higher)

21 626,040,08x.x3 SAME Ingress Guard 22 804,100,77x.x1 SAME Power Interrupt Switch - Cabinet

TBD – To Be Determined Part numbers subject to change with out notice.

Leveling Leg, 5/8-11x2 1/16″ (not shown)

Cabinet Assy., 72″ Domestic Cabinet Assy., 72″ Export

Page 63

PARTS

of 90

CABINET DETAIL

Page 64

PARTS

of 90

626,060,00x.x3

CABINET DETAIL

ITEM DN5000 PART # DN3000 Part # PART DESCRIPTION

1A 1B 626,060,30x.x3 TBD Cabinet Assembly Export 1C 637,050,50x.x3 TBD Cabinet Assembly Export Japan 2A 626,070,25x.x3 SAME Tray Support, Left Side (not shown) – Domestic 2B 626,070,62x.x3 SAME Tray Support, Left Side – Export 3A 626,070,08x.x3 NA Tray Support, Right Side – Domestic (prior to 001-8152) 3B 626,070,63x.x3 NA Tray Support, Right Side – Export (prior to 001-8152) 3C 626,070,67x.x3 SAME Tray Support, Right Side – Domestic (001-8152 and higher) 3D 626,070,71x.x3 SAME Tray Support, Right Side – Export (001-8152 and higher) 4A 626,070,19x.x3 SAME Tray Support, Rear – Domestic 4B 626,070,64x.x3 SAME Tray Support, Rear – Export 5A 626,020,05x.x3 636,020,05x.x3 Security Angle, Top 5B 626,020,12x.x3 SAME Security Angle, Left 5C 626,020,42x.x3 SAME Security Angle, Right

6 626,070,51x.x3 SAME Door Switch Bracket

7 804,100,77x.x1 SAME Door Switch

8 801,812,41x.x1 SAME *Discharge Door Frame Assy (Does not include Discharge 8A 801,812,90x.x1 SAME Discharge Door

8B - 1 801,817,51x.x1 SAME Discharge Frame – refrigerated side (001-8152 and higher) 8B - 2 801,812,91x.x1 NA Discharge Frame – refrigerated side (prior to 001-8152)

8C 801,812,92x.x1 SAME Discharge Frame Back 8D 801,401,92x.x1 SAME Discharge Door Rod 8E 901,701,15x.x1 SAME Discharge Door Spring 8F 801,814,29x.x1 NA Rivet, Plastic Snap 1/8” (prior to 001-8152)

8G 801,814,30x.x1 NA Cap, Plastic Snap 1/8” (prior to 001-8152)

9 804,915,76x.x1 SAME KO Machine Options Harness 10 801,305,71x.x1 SAME KO Mounting Plate 11 804,915,64x.x1 SAME Discharge Door Switch Harness 12 626,020,28x.x3 SAME Service Door Strike Plate 13 801,306,02x.x1 SAME Sensor Guard Plate 14 800,303,21x.x1 SAME Screw, 8-18x1/2 15 801,814,48x.x1 SAME Right Side Tray Support Spacer 16 801,306,14x.x1 NA Conveyor Guide, Right Side (001-8152 and higher) 17 626,050,33x.x3 636,050,01x.x3 Conveyor Product Deflector Ramp 18 801,306,14x.x1 SAME Right Side Conveyor Guide (001-8152 and higher)

*NOTE: 8063 production run needs a special discharge door frame assembly or the opening will need modification.

Part numbers subject to change with out notice.

636,060,20x.x3 Cabinet Assembly Domestic

Frame Back)

Page 65

PARTS

of 90

SERVICE DOOR FRONT

Page 66

PARTS

of 90

DN5000 & DN3000 SERVICE DOOR (FRONT)

CGF (Coke

Glass Front)

ITEM PART NUMBER PART NUMBER PART DESCRIPTION

1A 626,054,10x.x3 626,054,30x.x3 Service Door Assembly Domestic (IR)

1B 626,054,40x.x3 626,055,70x.x3 Service Door Assembly Export (IR) 1C 637,051,40x.x3 TBD Service Door Assembly Japan (IR)

2 626,050,10x.x3 626,053,10x.x3 Door Frame Assembly 3A 805,025,32x.x1 SAME Advertise Window

3B 801,305,75x.x1 SAME Retainer Clip, Ad Panel

4 803,859,34x.x1 803,866,96x.x1 Advertise Card, Domestic 5A 626,054,00x.x3 626,054,90x.x3 Transaction Panel Assembly Domestic

5B 626,052,40x.x3 TBD Transaction Panel Assembly Export 5C 637,050,90x.x3 TBD Transaction Panel Assembly Japan

6 801,810,69x.x1 SAME POS Lens, Coin Insert Panel 7A 626,050,36x.x3 SAME Backup Plate Flat Keypad, Coin Insert Panel

7B 624,050,48x.x3 SAME Backup Plate, Coin Insert Panel

8A 803,863,03x.x1 SAME Keypad Overlay – Flat Keypad

8B W453-2 SAME Keypad, Button Array – Rubber 8C 626,031,80x.x4 SAME Keypad Guard Kit (use with Button Array Keypad –Rubber)

9 804,918,26x.x1 SAME Membrane, Button Array

10A 626,050,03x.x3 SAME Membrane, Plate Back 10B 626,050,36x.x3 SAME Keypad Plate Flat (use with keypad overlay) 10C 626,010,60x.x4 SAME Flat Keypad Kit

11 805,701,24x.x1 SAME T-Handle Shim

12A 801,519,13x.x1 SAME T-Handle Assembly 12B 801,518,14x.x1 SAME T-Handle 12C 801,518,18x.x1 SAME T-Handle Flange 12D 801,519,14x.x1 SAME T-Handle Stud 12E 801,507,34x.x1 SAME External Retaining Ring 12F 901,503,06x.x1 SAME Flat Washer 12G 901,503,09x.x1 SAME Cross Pin 12H 901,503,05x.x1 SAME Spring

12I 901,508,18x.x1 SAME Spring

12J 626,050,32x.x3 SAME T-Handle Bracket

13 626,051,20x.x3 SAME Bottom Panel Service Door 14 803,858,37x.x1 803,866,41x.x1 Port Panel Decal 15 801,812,38x.x1 801,815,75x.x1 Port Bezel 17 626,050,01x.x3 SAME Coin Mech Panel 18 902,001,02x.x1 SAME Validator Gasket

19A 626,050,57x.x3 626,070,77x.x3 Trim, Top 19B Top Trim Locking Bar (no longer used)

20 626,070,74x.x3 626,070,75x.x3 Horizontal Trim 21 626,070,78x.x3 626,070,79x.x3 Vertical Trim

22A 803,863,46x.x1 803,868,20x.x1 Transaction Panel Label – English Domestic 22B 803,863,47x.x1 TBD Transaction Panel Label – French 22C 803,863,43x.x1 TBD Transaction Panel Label – English Export 22D 803,863,44x.x1 TBD Transaction Panel Label – French Canadian 22E 803,863,42x.x1 TBD Transaction Panel Label - Spanish

23 800,801,15x.x1 SAME Wiring Nut 8-32 (remote access panel) 24 804,916,26x.x1 SAME Flat Cable Mount (keypad harness) 25 803,862,78x.x1 SAME Validator Filler Label (not shown) 26 626,054,70x.x4 626,054,80x.x4 Kit, T-Handle Lock Cover

TBD – To Be Determined, not available at print.

DGF (Dasani Glass

Front)

Part numbers subject to change with out notice.

Page 67

PARTS

of 90

SERVICE DOOR (INSIDE)

Page 68

PARTS

of 90

DN5000 & DN3000 SERVICE DOOR (INSIDE)

ITEM PART NUMBER PART DESCRIPTION

1 626,050,20x.x3 Assembly Chute, Coin Insert 2 626,050,30x.x3 Assembly Coin Return 3 626,050,04x.x3 Coin Return Button Bracket 4 626,050,05x.x3 Coin Return Button Rocker 5 801,807,25x.x1 Coin Return Push Button 6 801,903,13x.x1 Bushing, .51Dx625 Hole 7 900,502,19x.x1 Roller Pin 8 900,900,90x.x1 Roller Pin Retainer (not shown)

9 901,701,07x.x1 Coin Return Spring 10 801,903,76x.x1 Red Display Filter 11 901,001,46x.x1 Stand Off, .192x312x312

12A 804,919,93x.x1 Display Domestic - IR (203-8211 and higher)

12B 804,914,86x.x1 Display Assembly (prior to 203-8211) 12C 804,920,05x.x1 Display Eprom (804,919,93x.x1 display board, 203-8211 and higher) 12D 804,914,97x.x1 Display Eprom (804,914,86x.x1 display board, prior to 203-8211)

13 801,806,58x.x1 Coin Hopper and Chute 14 801,806,59x.x1 Coin Chute Front 15 801,810,14x.x1 Change Cup 16 626,050,08x.x3 Cash Box Shelf

17 432,051,80x.x3 W/A Cash Box 18A 801,815,30x.x1 Injection Molded Discharge Port Assembly 18B 801,814,66x.x1 Discharge Port

19 626,050,23x.x3 Harvest Mounting Bracket 20A 624,050,93x.x3 Bill Validator Filler Plate 20B 637,051,00x.x3 Japanese Yen Validator Bracket Assembly

21 803,600,92x.x1 Discharge Port Pad

22 801,813,07x.x1 Backer Bezel Panel

23 626,050,25x.x3 Port Mounting Bracket

24 626,020,35x.x3 Vandal Plate, Port – Vacum Formed 25A 626,052,70x.x4 Vandal Plate, Vacuum Formed Port Kit (Prior to 318-8166) 25B 805,701,91x.x1 Vandal Plate, Injection Molded Port (318-8166 and higher)

25C 626,053,20x.x4 Injection Molded Port Assembly Kit 25D 805,702,07x.x1 Vandal Plate, Injection Molded – Extended (318-8166 and higher)

26 801,814,68x.x1 Cash Box Clip

27 626,052,10x.x3 Cash Box Lock Assembly

28 626,020,40x.x4 Griffin Card Reader Kit (includes card reader)

Part numbers subject to change with out notice.

Page 69

PARTS

of 90

TRAY ASSEMBLY

Page 70

PARTS

of 90

TRAY ASSEMBLY

ITEM DN5000 PART # DN3000 PART # PART DESCRIPTION

1 626,071,30x.x3 636,070,20x.x3 Tray Assembly 2 626,070,09x.x3 635,070,01x.x3 Tray Chassis 3 801,903,83x.x1 SAME Gate Assembly with Kicker 4 804,300,16x.x1 SAME Solenoid 5 801,519,29x.x1 SAME Plunger and Spring Assembly

6A 801,903,82x.x1 SAME Slide with Product Pusher Assembly 6B 801,812,79x.x1 SAME Product Pusher Slide, Bottom 6C 901,701,08x.x1 SAME Product Pusher Spring (not shown)

7 801,401,98x.x1 801,402,21x.x1 Wire Tray, Rigid 8 W485-1 SAME Label, Position Selection Sheet

9 622,070,04x.x3 SAME Side Shelf Stiffener (not shown) 10 W789 SAME Cotter Pin (not shown) 11 W218 SAME Solenoid Retainer Washer (not shown) 12 W398 SAME Retainer Washer (not shown)

13A D334 SAME 13B 800,101,94x.x1 SAME

14 901,901,00x.x1 SAME 15 See List SAME Spacers

15A 801,812,69x.x1 SAME Spacer – A 15B 801,812,81x.x1 SAME Spacer – B

16 804,913,74x.x1 804,920,34x.x1 Tray Harness (not shown)

17A 801,812,83x.x1 SAME Can Rotator, Gray – Snap in Rotator 17B 801,812,99x.x1 SAME Product Rotator, White - Snap In Rotator 18A 801,903,84x.x1 SAME Stabilizer, Columns 1 & 9 or 1 & 6 18B 801,903,85x.x1 SAME Stabilizer, Columns 2 through 8 or 2 through 5

19 900,301,56x.x1 SAME Screw, 8-32x3/8 Phil Pan (for old style rotator) 20 800,101,94x.x1 SAME ¼” Drive Socket 1/8” 6 point

Part numbers subject to change with out notice.

Screw, Hex Washer 4-24x3/4″ 1/8” (not shown) Socket, 1/8″ Drive 1/4″ Wire Tie, 4″ (not shown)

Page 71

PARTS

of 90

1A-2

1A-1

1A-2

1A-1

AC DISTRIBUTION BOX (DOMESTIC SHOWN)

prior to 049-8234

049-8234 & Up

prior to 049-8234

049-8234 and up

Page 72

PARTS

of 90

DN5000 & DN3000 AC DISTRIBUTION BOX

ITEM PART NUMBER PART DESCRIPTION

1A - 1 626,031,90x.x3 *AC Distribution Box Assembly T8 Electronic Domestic (049-8234 and higher) 1A - 2 626,030,40x.x3 AC Distribution Box Assembly Domestic 1A - 3 637,050,10x.x3 AC Distribution Box Assembly Japan

1B 626,030,70x.x3 AC Distribution Box Assembly Export 1C 626,031,30x.x3 AC Distribution Box Assembly Korea

2 804,920,02x.x1 Fuse Holder, Panel Mounted – Quick Disconnect 3 W658 Fuse 2 Amp 250V Slo Blo 4 W659 Fuse 10 Amp 32V Slo Blo 5 W662 AC Outlet, 15 Amp Grounded 6 804,913,62x.x1 Power Inlet Plug

7 804,915,54x.x1 Transformer, 110V / 24V 8A 8A 803,860,28x.x1 2 Amp Fuse / 10 Amp Fuse Label, Domestic 8B 803,860,83x.x1 Fuse Label, Export 9A 803,853,22x.x1 Label, Electrical Box “WARNING – DISCONNECT MAIN POWER CORD

BEFORE SERVICING”, Domestic

9B 803,860,84x.x1 Power Disconnect Label, Export

10A 804,920,56x.x1 *AC Distribution Harness Domestic T8 Electronic (049-8234 and higher) 10B 804,913,71x.x1 *AC Power In Harness, not shown - goes to item 6 (prior to 049-8234) 11A 804,920,58x.x.1 *Power Distribution Harness Domestic T8 Electronic (049-8234 and higher) 11B 804,915,87x.x1 *Power Distribution Harness, not shown – goes to item 5 (prior to 049-8234)

12 804,915,15x.x1 Rocker Switch Panel Mount 13 804,200,26x.x1 Relay 14 803,860,85x.x1 Main Power Label 15 804,920,41x.x1 Choke 16 903,825,86x.x1 Label, Warning High Voltage 17 804,913,77x.x1 Cord, Main Power 18 804,800,87x.x1 Circuit Breaker 30A Japan

19 804,916,93x.x1 Switch 3 Position Rotary (Exports only) *Includes 115 to 162 – 8233 Part numbers subject to change with out notice.

Page 73

PARTS

of 90

ELEVATOR

Page 74

PARTS

of 90

DN5000 & DN3000 ELEVATOR

ITEM PART NUMBER PART DESCRIPTION

1 805,202,37x.x1 Elevator with Motor Assembly 2A 804,100,99x.x1 Lower Motor Limit Switch 2B 801,306,03x.x1 Bracket, Home Position Aluminum

3 801,813,09x.x1 Upper Limit Switch Assembly

4 804,101,04x.x1 Lower Limit Switch Magnet

5 804,501,21x.x1 Elevator Motor

6 801,306,11x.x1 Washer, Aluminum

7 801,401,97x.x1 Belt Tensioner Spring

8 801,813,14x.x1 Elevator Drive Belt

9 804,800,84x.x1 Assembly Pillow Block

10 801,306,03x.x1 Aluminum Home Switch Bracket

Part numbers subject to change with out notice.

Page 75

PARTS

of 90

CONVEYOR

Page 76

PARTS

of 90

CONVEYOR

DN5000 DN3000

ITEM PART NUMBER PART NUMBER PART DESCRIPTION

1 626,070,50x.x3 636,070,00x.x3 Coke Conveyor Assembly

626,070,81x.x3 636,070,50x.x3 Dasani Conveyor Assembly

2 804,915,81x.x1 SAME Conveyor Assembly Wiring (not shown) 3 804,915,75x.x1 SAME Power Cord (not shown) 4 801,813,08x.x1 SAME Product Slide, Conveyor 5 801,812,65x.x1 SAME Tip Arm Base 6 801,401,94x.x1 SAME Tip Arm 7 626,050,33x.x3 SAME Product Deflector Ramp 8 626,070,31x.x3 SAME Coke Conveyor Deflector

626,070,83x.x3 SAME Dasani Conveyor Deflector

9 801,803,03x.x1 SAME Conveyor Nyliner

10 626,070,22x.x3 636,070,03x.x3 Coke Conveyor Rear Plate

626,070,22x.x3 636,070,04x.x3 Dasani Conveyor Rear Plate

11 626,070,21x.x3 636,070,10x.x3 Coke Conveyor Front Plate

626,070,72x.x3 636,070,90x.x3 Dasani Conveyor front Plate

12 804,501,16x.x1 SAME Conveyor Motor 13 800,503,09x.x1 SAME Conveyor Spacer 14 801,812,42x.x1 801,817,56X.X1 Conveyor Bed 15 801,812,85x.x1 SAME Conveyor Drive Pulley Assembly 16 801,812,84x.x1 SAME Conveyor Idler Pulley Assembly 17 804,915,81x.x1 SAME KO Conveyor Harness

18 801,812,35x.x1 801,817,57x.x1 19A 800,902,62x.x1 SAME Shoulder Phil Head with Locking Patch (001-8100 and higher) 19B 800,303,36x.x1 SAME Screw, Phil Pan 10-32X3/8 – conveyor to pillow block (prior to

19C 800,303,42x.x1 SAME Upgrade Kit Screws (prior to 001-8100) 19D 900,700,02x.x1 SAME Washer (used with 800,303,42x.x1) 19E 626,010,00x.x4 SAME Conveyor Mounting Screw (prior to 001-8100)

20 800,303,42x.x1 SAME Screw, Phil pan w/ Nylock #8-32x3/8

21 801,813,44x.x1 SAME Coke Conveyor Motor Cover

801,815,59x.x1 SAME Dasani Conveyor Motor Cover 22 801,814,48x.x1 SAME Tray Support Spacer 23 803,859,73x.x1 803,869,39x.x1 Coke Conveyor Decal

803,866,42x.x1 TBD Dasani Conveyor Decal

Note: Conveyor Motor gets 24VDC Elevator Motor gets 24VDC Elevator encoder gets 5VDC Part numbers subject to change with out notice.

Conveyor Belt (1.5″ wide, .125″ thick)

001-8100)

Page 77

PARTS

of 90

A6A B2A

A1A

LIGHTING

B2A B1A B3A

B3B

B1B B2B

A4A

A4B

Page 78

PARTS

of 90

ITEM DN5000 PART # DN3000 PART # PART DESCRIPTION

A1A 626,072,10x.x3 TBD *Assembly Lighting System, Cabinet T8 Electronic

Domestic/Japan (049-8234 and higher)

A1B 626,070,80x.x3 636,070,30x.x3 *Assembly Lighting System, Cabinet Domestic (prior to 049-

8234)

A1C 626,031,00x.x3 636,071,20x.x3 Assembly Lighting System, Cabinet Export

A2A 626,072,20x.x3 636,070,80x.x3 *Lamp Channel Assembly T8 Electronic Domestic (049-8234

and higher) A2B 626,070,90x.x3 NA Lamp Channel Assembly (prior to 049-8234) A3A 804,920,53x.x1 SAME Cabinet Lighting Harness T8 Electronic A3B 804,915,67x.x1 NA Cabinet Lighting Harness (not shown) A4A 804,400,58x.x1 SAME *Ballast HF-P218TLD, 220-240V T8 Electronic Domestic (049-

8234 and higher) A4B 804,400,44x.x1 NA *Ballast, 20 Watt Pre-Heat Domestic (prior to 049-8234)

A4C 804,400,58x.x1 SAME Ballast HF-P 218 TLD 220-240V Electronic Export A4D 804,400,71x.x1 SAME Ballast, 2 Lamp T8 Electronic Advance 120/60

A4E 626,030,90x.x3 TBD Ballast Electronic Long, Assembly - Export

A5 801,903,90x.x1 801,904,38X.X1 Lamp Shield

A6A 804,700,79x.x1 NA *Lamp, 30 inch F021/865/XP/ECO - T8 (049-8234 and higher)

NA 804,700,82X.X1 Lamp, 18 inch F013/865/XP/ECO - T8

A6B 804,700,69x.x1 NA

NA 804,700,89x.x1 A7 904,800,41x.x1 NA Starter FS-25 A8 804,101,07x.x1 SAME Switch, PI A9 626,070,61x.x1 NA Lamp Channel Starter Bracket

A10A 801,904,35x.x1 801,904,37x.x1 *Lamp Cover, Instant Start T8 (049-8234 and higher) A10B 801,904,06x.x1 NA *Lamp Cover (prior to 049-8234)

A11 801,904,06x.x1 SAME End Caps, Lamp Sleeve

B1A 626,055,20x.x3 SAME *Sub Assembly Service Door Lamp T8 Domestic (049-8234 B1B 626,050,80x.x3 SAME *Sub Assembly Service Door Lamp, Domestic (prior to 049B1C 626,031,10x.x3 SAME

B1D 637,051,50x.x3 SAME Sub Assembly Service Door Lamp T8 Japan

B2A 804,700,81x.x1 SAME *Lamp, U shaped FB016/865/XP, T8 (049-8234 and higher) B2B 804,700,35x.x1 SAME *Lamp, F13T8CW (prior to 049-8234)

B3A 626,050,51x.x3 SAME *Service Door Lamp Bracket T8 (049-8234 and higher)

B3A 804,920,54x.x1 SAME *Door Lighting Harness T8 Electronic, not shown (049-8234 B3B 626,050,22x.x3 SAME *Service Door Lamp Bracket (prior to 049-8234)

B4B 804,915,65x.x1 SAME *KO Door Lighting Harness, not shown (prior to 049-8234)

B5 805,507,27x.x1 SAME Converter, ADU018 CLX MDB-UCCS Box Japan C1 803,870,05x.x1 SAME *Label, T8 Lamp Replacement (049-8234 and higher)

* Includes 115 to 162 - 8233 Part numbers subject to change with out notice.

*Lamp, F18 T8 CW/30″ (prior to 049-8234) Lamp, F15 T8/CW/18″ Export

and higher)

8234) Sub Assembly Lamp Service Door 13″ Export

and higher)

LIGHTING

Page 79

PARTS

of 90

REFRIGERATION

Page 80

PARTS

of 90

DN5000 & DN3000 REFRIGERATION

ITEM PART NUMBER PART DESCRIPTION

1 626,041,60x.x4 Domestic Kit – Refrigeration System 2000C-A 115/60 1A 626,040,00x.x3 Refrigeration System 2000C-A 115/60, Domestic/Japan 1B 626,041,00x.x3 Refrigeration System 2020C-A, Export 1C 626,041,90x.x3 Refrigeration System 2030C-A, Export Korea 2A 626,040,60x.x3 Compressor Assembly 115 / 60, Domestic/Japan 2B 626,041,30x.x3 Compressor Assembly 220-240/50, Export 2C 626,042,30x.x3 Compresso Assembly 208-230/60, Export Korea 3A 802,502,22x.x1 3B 802,502,25x.x1 3C 802,502,30x.x1 Compressor “A” T6213Z 208-230/60, Export Korea 4A 802,502,23x.x1 Overload, T1 MST16AFN-3001, Domestic/Japan 4B 802,502,26x.x1 Overload, T1 MRP20APK-34, Export 4C 802,502,31x.x1 Overload, T1 MRT18GL 3001, Korea 5A 802,500,94x.x1 Relay, T1 9660-041-180, Domestic/Japan 5B 802,502,27x.x1 Relay, T1 9660-041-158, Export 5C 802,502,32x.x1 Relay, T1 9660-041-179 EM, Korea

6 802,502,01x.x1 Cover, Overload / Relay Tecumseh 7A 802,502,24x.x1 Capacitor Start 189227, Domestic/Japan 7B 802,502,28x.x1 Capacitor Start 88-108MFD / 250 V 50 Hz., Export 7C 802,502,33x.x1 Capacitor Start 66-77 MFD/330V50/60HZ, Korea

8 802,501,18x.x1 Capacitor End Cap Bottom Hole

9 802,501,87x.x1 Bracket Capacitor Assembly

10A 801,812,61x.x1 Drain Pan, Condensate Domestic 10B 801,813,55x.x1 Drain Pan, Condensate Export 11A 626,040,70x.x3 Assembly, Condenser Fan 16 W, 10 Inch Domestic/Japan 11B 626,041,40x.x3 Assembly, Condenser 16W 220V Export/Korea 12A 804,501,14x.x1 Condenser Fan Motor, 16W 12B 804,501,18x.x1 Condenser Fan Motor, 16W 220V

13 902,100,29x.x1 Silencer 14 801,305,67x.x1 Fan Blade, Condenser FV100CW25S 15 900,800,85x.x1 Speed Nut 16 802,600,64x.x1 Condenser 17 802,401,30x.x1 Dryer 18 902,000,57x.x1 Grommet Compressor 19 802,600,63x.x1 Evaporator

20 802,401,35x.x1 Accumulator 21A 802,800,60x.x1 Defrost Control 21B 801,902,75x.x1 Defrost Control Vinyl Tube

21C 626,020,34x.x3 Defrost Thermostat Guard

22A 626,040,80x.x3 Assembly Drain Pan, Evaporator 22B 801,814,62x.x1 Drain Pan

22C 801,806,05x.x1 Drain Tube 22D 900,301,79x.x1 Drain Tube Nut

22E 901,900,50x.x1 Drain Hose 22F 900,901,03x.x1 Drain Hose Clamp

23 626,040,04x.x3 Evaporator Fan Shroud 24A 804,501,09x.x1 Evaporator Fan Motor Assembly, Domestic/Japan 24B 804,501,11x.x1 Evaporator Fan 8” 9W, 220-230 / 50, Export 25A 801,812,63x.x1 Side Gasket, Drain Pan 25B 801,812,64x.x1 Front Gasket, Drain Pan

26 626,040,09x.x3 Refrigeration Side Brace

27 804,919,66x.x1 Encapsulated Temperature Sensor

Part numbers subject to change with out notice.

Compressor ″A″ T6213Z 115 / 60, Domestic/Japan Compressor ″A″ 220-240 / 50 T6213Z, Export

Page 81

PARTS

of 90

ELECTRONICS

Page 82

PARTS

of 90

DN5000 & DN3000 ELECTRONICS

ITEM PART NUMBER

NEW

1A 626,056,30x.x4 TBD KO Board Universal Assembly (T8) 077-8272 & up 1B 626,030,21x.x3 SAME KO Board Mounting Plate 1C 626,050,48x.x3 SAME KO Board Cover 077-8272 & up

627,050,31x.x3 SAME KO Board Cover prior to 077-8272

2A 626,032,10x.x3 TBD Machine Board, Domestic/Japan 099-8212 & up 2B 626,032,20x.x3 TBD Machine Board, Export

2C - 1 626,030,36x.x3 SAME Machine Board Cover, ESD (099-8212 and higher) 2C - 2 801,904,16x.x1 SAME Machine Board Cover, Plastic (prior to 099-8212) 2D - 1 626,030,37x.x3 SAME Machine Controller Mounting Plate (099-8212 and higher) 2D - 2 622,050,32x.x3 SAME Machine Controller Mounting Plate (prior to 099-8212)

2E 801,903,87x.x1 SAME Control Board Stand Offs, Richo

3A 804,919,93x.x1 SAME Display Assembly, ASD (203-8211 and higher) 3B 804,914,86x.x1 SAME Display Assembly (prior to 203-8211)

4 804,100,77x.x1 SAME Door Switch 5 804,100,99x.x1 SAME Lower Motor Limit Switch 6 804,101,04x.x1 SAME KO Limit Switch Magnet 7 804,101,05x.x1 SAME Unencapsulated Magnet 8 804,915,84x.x1 SAME 24 VDC Snap In Mount Counter

9A 626,020,44x.x4 SAME Override Switch Kit 9B 801,510,10x.x1 SAME Override Switch

10 804,914,99x.x1 SAME EPROM, KO Board

11 804,914,16x.x1 SAME EPROM, Machine Board

12A 804,920,05x.x1 SAME EPROM, Display (203-8211 and higher) 12B 804,914,97x.x1 SAME EPROM, Display (prior to 203-8211)

13 626,050,52x.x4 SAME MDB Electronic Interface Kit Japan

14A 637,050,60x.x3 SAME Stabilizer Enclosure Box Assembly Japan 14B 804,400,76x.x4 SAME Voltage Stabilizer Kit (105V) Japan 14C 804,400,73x.x1 SAME Voltage Stabilizer Transformer (105V) Japan 14D 637,050,70x.x3 SAME Stabilizer Enclosure Door Assembly Japan

Part numbers subject to change with out notice.

PART NUMBER

REMANUFACTURED

PART DESCRIPTION

Page 83

PARTS

of 90

HARNESSES

ITEM PART

NUMBER

1 804,913,74x.x1 Tray Harness 8 Column Solenoids to J3, J4, J5, J6, J7 on Machine

804,920,34x.x1 Tray Harness 6 Column Solenoids to J3, J4, J5, J6, J7 on Machine

2A 804,920,54x.x1 *Door Lighting Hartness T8 Electronics

(049-8234 and higher)

2B 804,915,65x.x1 *Door Lighting Harness

(prior to 049-8234) 3 804,915,81x.x1 Conveyor Harness Elevator E-Chain harness 4 804,915,69x.x1 Relay Control Harness Lights, Fan, Compressor to P5 on Machine

5 804,919,66x.x1 Encapsulated Temperature Sensor

(factory installed beginning 001-8152) 6 804,915,64x.x1 Discharge Door Switch Harness Discharge door to J10 on Machine board 7 804,915,76x.x1 Machine Options Harness Counter / Override / Door Switch to P7 on KO

8 804,915,62x.x1 Board to Board Communication

Harness

9A 804,920,63x.x1 *Main Power Harness T8 Electronic

(049-8234 and higher)

9B 804,915,59x.x1 *Main Power Harness

(prior to 049-8234)

9C - 1 804,913,77x.x1 Main Power Cord 9C - 2 804,920,70x.x1 Power Adapter Japan

10 804,915,72x.x1 Override Switch Harness Service Option to KO machine option harness

11A 804,920,53x.x1 *Cabinet Lighting Harness T8

Electronic (049-8234)

11B 804,915,67x.x1 *Cabinet Lighting Harness

(prior to 049-8234)

12 804,915,89x.x1 DC Door Bundle Assy. Display, MDB peripheral, DEX to P9, P3, and 13 804,915,91x.x1 DC Main Bundle Assy. Conveyor, Elevator, Kill / Limit Switch, to J2, J8,

14A 804,916,24x.x1 Secondary KO DEX Harness KO board to port 14B 800,801,29x.x1 Nut, DEX harness Nut to secure DEX harness in port. 15A 626,020,44x.x4 Override Switch Kit 15B 801,510,10x.x1 Override Switch / Lockout 15C 804,915,72x.x1 CGFV Override Harness 15D 901,512,11x.x1 Key

16 804,914,74x.x1 Internal / External KO DEX Harness

17 804,920,71x.x1 Voltage Stabilizer Harness Japan 18A 804,920,41x.x1 Choke 18B 804,920,49x.x1 Choke Output Harness 18C 804,920,84x.x1 Choke Input (AC Power) Harness

19 804,920,72x.x1 ADU Power Harness Japan

* Include 115 to 162 - 8233 Part numbers subject to change with out notice.

PART DESCRIPTION FROM / TO

Board Board

From service door light to DC door bundle assembly From service door light to DC door bundle assembly

board From Machine Board to Evaporator

Board J1 on Machine Board to J14 on KO board

9 pin plug on AC box to lights, temperature control, and P5 on machine board 9 pin plug on AC box to lights, temperature control, and P5 on machine board

Cabinet light to DC door bundle assy.

P1 on KO board and J9 on Machine Board

Page 84

PARTS

of 90

LABELS / DECALS / MISC.

CGF (Coke

Glass Front)

ITEM PART NUMBER PART NUMBER

1 803,859,74x.x1 Bottom Glass Door Decal 2 803,859,72x.x1 803,866,39x.x1 Top Glass Decal 3 803,859,71x.x1 803,866,43x.x1 Cabinet, Side Decal 4 803,857,26x.x1 Selection Label 5 803,856,15x.x1 Asset / Property Tag Coca-Cola Company 6 803,868,29x.x1 Warning: DO NOT TILT Label, Tri Lingual 7 803,859,73x.x1 803,866,42x.x1 Conveyor Decal 8 803,853,21x.x1 AC Distribution Box Fuse Label (2 Amp – 10 Amp)

9 803,853,22x.x1 AC Distribution Box Power Disconnect Label 10 803,860,61x.x1 Quick Reference Program Label 11 803,853,25x.x1 Validator / Changer Label 12 803,858,37x.x1 803,866,41x.x1 Port Panel Decal 13 803,870,05x.x1 T8 Lamp Replacement Label (049-8234 and higher) 14 803,857,26x.x1 Selection Label Sheet (white with black letters – column #’s) 15 803,903,03x.x1 Manual, Technical 16 803,902,99x.x1 Quick Reference Laminated Card 17 803,903,02x.x1 Price Setting Programming Reference Guide 18 W485-2 thru 13 Price Sheets 19 803,903,04x.x1 Literature Package (includes items #5, 10, 15, 16, 17, and 18) 20 803,861,31x.x1 Package Setup Label

21A 803,862,37x.x1 Coke Flavor Card Sheet 1 21B 803,862,38x.x1 Coke Flavor Card Sheet 2 22A 803,862,41x.x1 Generic Flavor Card Sheet 1 22B 803,862,42x.x1 Generic Flavor Card Sheet 2

23 803,903,09x.x1 DN 5000 Foot Print

24A 803,903,15x.x1 Do’s and Don’ts CD 24B 803,903,14x.x1 Programming CD 24C 803,903,13x.x1 Technical Information CD

25 626,010,50x.x4 Spare Parts Start Up Kit 26 803,863,62x.x1 Tag, Caution – DO NOT MOVE ELEVATOR 27 803,863,01x.x1 Label, Caution – DO NOT MOVE ELEVATOR 28 803,862,82x.x1 29 803,863,03x.x1 Label, Sec Ang Removal English CGF 30 803,862,78x.x1 Label, Validaotr Filler 31 626,020,40x.x4 Kit, Griffin Card Reader 32 803,868,24x.x1 Label, Fuse Cvr Mtr Svc 33 803,862,54x.x1 ON/OFF Rocker Switch Label 34 803,853,24x.x1 DO NOT DOUBLE STACK Label 35 803,863,41x.x1 Quality Assurance Label 36 803,861,13x.x1 Maytag Commercial Label 37 803,862,76x.x1 CGFV Wiring Diagram 38 626,052,10x.x4 DN5000 Upgrade Kit (Venders prior to 001-8100) 39 803,870,05x.x1 T8 Flur. Lamp Replacement Lamp Label (049-8234 & higher)

Part numbers subject to change with out notice.

DGF (Dasani

Glass Front)

PART DESCRIPTION

Label, Encoder ″Do Not Remove Cover ″

Page 85

PARTS

of 90

SCREWS AND NUTS

Page 86

PARTS

of 90

SCREWS & NUTS

ITEM PART NUMBER PART DESCRIPTION

A1 900,301,70x.x1 A2 900,301,64x.x1 A3 900,301,83x.x1 A4 900,301,50x.x1 A5 900,301,97x.x1 A6 900,300,47x.x1 A7 900,301,82x.x1 A8 900,301,61x.x1

A9 900,301,56x.x1 A10 900,201,31x.x1 A11 900,301,97x.x1 A12 900,301,85x.x1 A13 900,300,16x.x1 A14 900,301,81x.x1 A15 900,201,14x.x1 A16 900,301.65x.x1 A17 900,302,01x.x1 A18 900,301,69x.x1 A19 900,901,51x.x1 A20 900,201,22x.x1 A21 900,301,98x.x1 A22 900,301,84x.x1 A23 900,500,26x.x1 A24 900,201,13x.x1 Screw, Hex Head A25 900,301,73x.x1 A26 800,303,15x.x1 A27 800,303,18x.x1 Screw, Truss Type 23 #8-32x1/2 A28 900,301,94x.x1 A29 900,201,44x.x1 A30 900,301,99x.x1 Screw, Plastic 8-hi/low x 1-1/4 A31 900,301,55x.x1 Screw, Phil Pan Swage Form #8-32x1/2 Screw A32 900,303,08x.x1 A34 800,303,22x.x1 Screw, Phil Pan #6-20x3/8 A35 900,302,02x.x1 Screw, Self Tapping #8-18x3/4 A36 900,201,86x.x1 A37 900,301,91x.x1 A38 900,201,87x.x1 Screw, Phil Truss #10-32x3/8 A39 W796 A40 W948 A41 800,303,21x.x1 Screw, Phil Pan Sems #8-18x1/2 A42 800,303,34x.x1 Screw, Phil Pan 8-Hilox 1/2 A43 D334 Screw, Hex Washer 4-24x3/4 A44 W851 Screw, Pan Head A45 900,301,70x.x1 Screw, Phil Pan #6-32x3/8 A46 800,902,62x.x1 Screw, Shoulder

B1 900,800,65x.x1 Hex Nut, #10-32

B2 900,800,67x.x1 Hex Nut, 1/4-20

B3 900,800,50x.x1 Hex Nut, #8-32

B4 900,800,69x.x1 Hex Nut, Top Door Hinge, 3/8-16

B5 900,800,85x.x1 Speed Nut

Part numbers subject to change with out notice.

Screw, Phil Pan Swage Form #6-32x3/8″ Screw, Phil Pan Swage Form w/ Washer #8-32x1/2″ Screw, Phil Pan Swage Form #10-32x5/16″ Screw, Phil Pan without Washer, #8-18x1/2″ Screw, Phil Pan Swage Form #8-32x1/4″ Screw, Vend Motor, #4-24x3/4″ Single Switch Screw, Vend Motor, #4-24x1-16 ″ Double Switch Screw, Vend Motor #4-24x1-1/2″ Triple Switch Screw, Phil Pan Cutting #8-32x3/8 ″ Screw, Machine, #6-32x1-1/4 ″ Screw, Phil Pan Sems #8-32x1/4″ Screw, Phil Pan Thread Form #8-32x5/8″ Screw, Phil Head Truss #6x3/8″ Screw, Phil Pan Form #10-32x1-1/4″ Screw, Machine Truss, #10-32x1/2″ Screw, Phil Pan Sems with Washer, #8-18x1/2″ Screw, Self Tapping, 1/4″-20x5/8″ Screw, Hex Head Swage Form #8-36x3/8″ Screw, Phil Pan Tapping #10-23x5/8″ Screw, Machine Phil Pan #8-32x3/4″ Screw, Phil Pan Shoulder #8-18x1/2″ Screw, Phil Pan #8-18x1/2″ Shoulder Screw, 1/2″ Long

Screw, Tap ½-20x1″ Type F Screw, Phil Pan #8-18x3/4″

Screw, Phil Flat 23B #10-32x1/2″ Screw, Machine Brass #6-32x1/4″

Screw, Hex Washer Type 1 #8-32x3/8″

Screw, Phil Pan Head #6-32x1/4″ Screw, Hex Wash #8-18x1/2″

Screw, Taper Tite #8-18x3/8″ Screw, Hex Head #10-16x50″

Page 87

PARTS

of 90

SCREWS & NUTS (Continued)

ITEM PART NUMBER PART DESCRIPTION

B6 900,800,49x.x1 Hex Nut, #6-32

B7 900,800,51x.x1 Elastic Stop Nut, #8-32

B8 900,800,81x.x1 Hex Nut, 8-32

B9 900,902,37x.x1 Push Nut, Acorn Type B10 900,801,02x.x1 Hex Nut, 5/16-18 B11 800,801,13x.x1 Nut, Self Clinching 5/16-18 B12 800,303,38x.x1 SCREW,8-18x1/2 (Bottom Skirt)

Part numbers subject to change with out notice.

Page 88

PARTS

of 90

WASHERS / BOLTS / MISC HARDWARE

Page 89

PARTS

of 90

WASHERS , BOLTS, AND MISC. HARDWARE

ITEM PART NUMBER PART DESCRIPTION

C1 900,700,60x.x1

C2 901,303,77x.x1 Washer, Door Hinge

C3 901,503,06x.1 Washer, Flat #2949 (T-Handle)

C4 901,503,08x.x1 Washer, Hex #29.34 (T-Handle)

C5 900,700,36x.x1

C6 900,700,89x.x1

C7 900,700,02x.x1

C8 900,700,62x.x1 Washer, Shakeproof (4610-16-01-0551)

C10 900,700,83x.x1 C11 900,700,08x.x1 C12 801,902,48x.x1 Nylon Spacer C13 W884 Washer, Lock C14 W398 Washer, Fender .125 ID C15 W218 Washer, Solenoid Retainer C16 801,518,03x.x1 C17 W861 C18 900,701,15x.x1

900,701,05x.x1

D1 900,400,43x.x1

D2 900,400,41x.x1

D3 900,400,35x.x1

D4 900,400,45x.x1

E1 900,400,44x.x1

E2 900,201,17x.x1

E3 900,201,23x.x1

E4 900,201,45x.x1

E5 900,201,54x.x1

E6 900,201,56x.x1

E7 900,303,12x.x1

E8 900,201,85x.x1

E9 800,303,19x.x1 E10 900,202,04x.x1 E11 W766 Carriage Bolt, 1/4-20

F1 901,100,43x.x1

F2 901,100,44x.x1

F4 901,100,54x.x1

F5 901,100,61x.x1

F6 901,100,53x.x1

F7 901,100,60x.x1

F8 801,100,67x.x1

F9 801,100,65x.x1

Part numbers subject to change with out notice.

Washer, Delrin .047 Thick 3/8″ ID x 5/8 OD

Lockwasher, Split 3/8″ Lockwasher, Shakeproof 5/8″ (1132-00-00-0551) Steel Washer, 18 Gauge (1/2″ x 3/16″)

Washer, Flat 18 Gauge (17/64″ ID x 58″ OD) Washer, Flat 14 Gauge (5/16″-3/8″)

Washer, Tooth Lock 1/2″ Washer, Flat .265″ ID x .50″ OD Washer, 11/64″ ID x 11/32″ OD Washer, Flat .343″ ID x .688″ OD .6T

T-Bolt, #8-32x1″ (obsolete) T-Bolt, #8-32x1-3/8″ T-Bolt, #8-32x3/4″ T-Bolt, #8-32x1/2″

Refrigeration Bolt, 3/8-16x1″ Carriage Bolt, 1/4-20x1″ Carriage Bolt, 1/4-20x1-1/4″ Carriage Bolt, 1/4-20x1/2″ Carriage Bolt, 1/4-20x3/8″ Carriage Bolt, 1/4-20x3/4″ Carriage Bolt, 1/4-20x5/8″ (obsolete) Carriage Bolt, 5/16x18x1-14″ Top Hinge (drop in) Carriage Bolt, 1/4-20x5/8″ Carriage Bolt, 1/4-20x1/2″ (red)

Pop Rivet, Aluminum 1/4″ Drive Rivet, #38-108-06-13 1/4″ Pop Rivet, Black 1/8″ Pop Rivet, Steel (zinc plated) 1/8″ Pop Rivet, Aluminum 1/8″ Pop Rivet, Steel (zinc plated) 3/16″ Pop Rivet, Aluminum Black 1/8″ Pop Rivet, Aluminum White 1/8″

Page 90

PARTS

of 90

WASHERS , BOLTS, AND MISC. HARDWARE (continued)

ITEM PART NUMBER PART DESCRIPTION

H1 900,902,13x.x1 Christmas Tree Clip #354280307-00

H2 900,901,89x.x1 Tinnerman Clip, Fan Shroud (C5207-014-3B)

H3 900,401,09x.x1 Grommet, Bk. Rubber #97

H4 901,503,07x.x1 E-Ring #31-30

H5 900,900,90x.x1 Retainer, Roller Pin

H6 900,902,18x.x1 Tinnerman Clip

H7 801,807,01x.x1 Hole Plug, Snap-In 1-1/4

H8 901,806,77xx.1 Grommet, Admiral #B53351

H9 902,100,29x.x1 Silencer H10 801,903,80x.x1 Standoff (Machine Controller) H11 901,502,53x.x1 Shipping Spring Clip H12 801,903,87x.x1 2nd Standoff

I1 804,601,45x.x1 #6 Terminal Ring Crimp 16-14 AWG I2 801,902,48x.x1 Nylon Spacer used on Coke D/O Boards I3 801,809,12x.x1 Velcro Blocks I4 801,807,49x.x1 Vender Defender Clamp I5 901,901,89x.x1 I6 900,901,79x.x1 I7 900,901,80x.x1 I8 901,901,06x.x1 Hand Tie, 5.5”

I9 901,902,01x.x1 I10 901,901,00x.x1 I11 901,900,55x.x1 I12 901,902,83x.x1 I13 900,902,14x.x1 Canoe Clip #254-090-301-00-0108 I14 W904 Hex Bolt, 1/4-20x1 I15 W844 Cable Tie I16 D588 Flat Cable Mount

Part numbers subject to change with out notice.

Clamp, Cable 1″ I6Heyco 3390 Clamp, Nylon 5/16″ Black Heyco 3355 or Dennison 10159 Clamp, Nylon 1/2″ Heyco 3328

Wire Tie, 7-1/2″ Wire Ties, 4″ Clamp, Nylon 3/4″ Heyco 3382BL Cable Tie, 5.5″