Maytag CWG3100AAS, 9112XUB Installation Guide

INSTALLER" LEAVE THESE INS TRUG TIONS WITH THE APPLIANCE

INSTALLATION MANUAL

Gas 24-inch Built-ln Ovens

PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE

THE MANUAL IS INTENDED TO ASSIST IN THE INITIALINSTALLATION AND ADJUSTMENTS OF THE RANGE

Clearance Dimensions

For complete information in regard to the installation of

wall ovens and clearances to combustible wall above the

Only qualified personnel should install or service this range.

Read "Safety Instructions" in the

Use & Care book before using range.

Improper installation, adjustment,

alteration, service, maintenance or use of range can result in serious

injury or property damage.

cooking top see the installation drawings.

A WIRING DIAGRAM IS ENCLOSED IN THE ENVELOPE WITH THIS BOOKLET; ALSO THERE IS A DIAGRAM GLUED TO THE UNIT, BEHIND CONTROL

PANEL.

CAUTION: SOME CABINETS AND BUILDING

MATERIALS ARE NOT DESIGNED TO WITH- STAND THE HEAT PRODUCED BY THE

NORMAL SAFE OPERATION OF A LISTED APPLIANCE. DIS- COLOATION OR DAMAGE,

SUCH AS DELAMINATION, MAY OCCUR.

Your range may not be equipped with some of the features referred to in this

manual.

8101 P590-60

(o8-o5-o1)

Installation Drawings

PROVIDE SLOT

120 VOLT GROUNDED

ELECTRICAL OUTLET

IN THIS AREA

FRONT OF CABI

OVEN SUPPLIED WITH

112" NPT FEMALE INLET

ON REGULATOR.

62"

WITH A 3

PRONG CORD

I I

I I I I

MIN

4" RECOMMENDED AREA FOR ELECTRICAL

CONNECTION

45-318"

IDE HOLE IN THIS GENERAL AREA FOR CONNECTING TO

112" DIAMETER PIPE

FITTING

46-5/16"

COMPLETE FLOC

IS RECOMMENDED

TO PREVENT

14" MIN.

HEIGHT

UNUSUAL DRAFTS.

URE OVEN TO CABINET THROUGH

HOLES PROVIDED IN TRIM. FOUR

SCREWS SHIPPED WITH UNIT.

FIGURE I

24" GAS WALL OVENS

UPPER OVEN LOWER OVEN OR BROILER OVEN FRAME SIZE CUTOUT DIMENSIONS

MODEL WIDTH HEIGHT DEPTH WIDTH HEIGHT DEPTH WIDTH HEIGHT WIDTH HEIGHT "A" DEPTH

DOUBL_

OVEN 18" 14" !9" 18" 12" 19" 23 7/8" 46 5/16" 22" 45 318" 24"

3VEN WIT}[

_I{on,ER 18" 14" 19" 18" 6.25" 19" 23 718" 39 114" 22" 38" 24"

-2-

"A" "B"

Installation

Check the oven model number plate to see if the oven is approved for installation in mobile homes and/or

recreational vehicles. If approved the following items are applicable. NOTE: Oven model number plate is located

under broiler bottom.

Mobile Homes

The installation of an oven designed for mobile home installation must conform with the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24 HUD, (Part 280) or,

when such standard is not applicable, the Standard for

Manufactured Home Installations, ANSI A225.1/NFPA 501A, or with local codes.

In Canada the range must be installed in accordance with the current CSA Standard C22.1 - Canadian Electrical Code Part 1 and Section Z240.4.1 - Installation

Requirements for Gas Burning Appliances in Mobile Homes (CSA Standard CAN/CSA - Z240MH).

Recreational Vehicles

The installation of an oven designed for recreational vehicles must conform with state or other codes or, in the absence of such codes, with the Standard for

Recreational Vehicles, ANSI A119.2-latest edition. In Canada the oven must be installed in accordance with CAN/CSA - Z240.6.2 - Electrical Requirements for R.V.'s

(CSA Standard CAN/CSA - Z240 RV Series) and Section Z240.4.2 - Installation Requirements for Propane

Appliances and Equipment in R.V.'s (CSA Standard

CAN/CSA - Z240 RV Series).

Locating The Unit

The installation diagram gives the minimum dimensions of the cabinet cut-out for the oven. The dimensions given

are for the oven bottom to be a minimum of 14" inches above the floor. The recess in which the oven is to be

installed should have a solid floor and be so constructed as to provide a complete enclosure around the recessed

portion of the oven to prevent drafts which may result in inconsistent and unsatisfactory burner and baking

performance, it should be perfectly level to provide a solid, level foundation for the oven unit. The openings in

the enclosure for gas and electric service should be sealed before the oven is installed.

For SAFETY CONSIDERATIONS fasten the oven to the cabinet with the four (4) screws (shipped with the unit)

through the holes in the trim behind the oven and broiler doors. The unit should be leveled properly before being

secured to the cabinet.

Electric Supply

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the

absence of local codes, with the National Electrical Code,

ANSI/NFPA 70.

In Canada the oven must be installed in accordance with the current CSA Standard C22.1 - Canadian Electrical

Code Part 1. ELECTRICAL SUPPLY CONNECTION:

The oven requires 120 volts, 60 cycle alternating current

from an outlet capable of supplying 15 amperes.

User may experience occasional circuit tripping if Ground Fault Circuit Interrupter (GFCl) outlet or breaker is in use.

, WARNING

Electrical Grounding Instructions

This appliance is equipped with a (three-prong) grounding plug for your protection against shock

hazard and should be plugged directly into a properly grounded receptacle. Do not cut or remove

the grounding prong from this plug.

I WARNING

DISCONNECT ELECTRICAL SUPPLY

BEFORE SERVICING THE APPLIANCE.

-3-

+ 5 hidden pages