240EdwardsStreet,SE
CEeveJandTennessee37311
Te1:423-472-3333
Fax:423478-6710
INSTALLATION INSTRUCTIONS
FOR YOUR
MICROWAVE OVEN
INSTALLATION INSTRUCTIONS FOR CABINET-WALL MOUNTED MICROWAVE OVEN
WITH
BUILT-IN VENT AND COOKTOP LIGHT
SAVE THIS BOOK WITH YOUR USE AND CARE BOOK
READ ALL INSTRUCTIONS THOROUGHLY BEFORE INSTALLING YOUR MICROWAVE OVEN.
NOTE: IT IS RECOMMENDED THAT TWO PEOPLE INSTALL THIS PRODUCT.
IMPORTANT: KEEP INSTRUCTIONS FOR LOCAL INSPECTOR'S USE.
[] _'vL_'II-AG _drnlral 71 :gm_.JENN-,_= "_lagic Chef
CustomerService _1_1_1_
2@EdwardsStreet,SE
Cleveland,Tennessee37311
Tel:s22-_t72-3333
Fax:423-478-6710
STEP 1
REQUIREMENTS FOR INSTALLATION
IMPORTANT SAFETY INSTRUCTIONS
This product requires a three-prong grounded receptacle. The installer must perform a ground continuity check
on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If
not properly grounded, or if the outlet box does not meet the electrical requirements note, (under ELECTRi-
CAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.
CAUTION: FOR PERSONAL SAFETY, REMOVE HOUSE FUSE OR OPEN CIRCUIT BREAKER
BEFORE BEGINNING INSTALLATION TO AVOID SEVERE OR FATAL SHOCK INJURY.
CAUTION: FOR PERSONAL SAFETY, THE MOUNTING SURFACE MUST BE CAPABLE OF
SUPPORTING THE CABINET LOAD, IN ADDITION TO THE ADDED WEIGHT OF THIS 65
POUND PRODUCT, PLUS ADDITIONAL OVEN LOADS OF UP TO 50 POUNDS OR A TOTAL
WEIGHT OF 115 POUNDS.
CAUTION: FOR PERSONAL SAFETY THIS PRODUCT CANNOT BE INSTALLED TO CABINET
ARRANGEMENTS SUCH AS AN ISLAND OR A PENINSULA, IT MUST BE MOUNTED TO BOTH A
TOP CABINET AND A WALL.
ELECTRICAL REQUIREMENTS
Product rating is 120 volts, AC, Hertz, 12.0 amps, and 1.35 kilowatts. This product must be connected to a
supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the
National Electric Code or the prevailing local code for this kilowatt rating. The power supply cord and plug
should be brought to a separate 15 or 20 ampere branch circuit single grounded receptacle. The outlet box
should be located near the cord entry point. The outlet box and supply circuit should be installed by a qualified
electrician and conform to the National Electric Code or the prevailing local code.
NOTE: FOR EASIER INSTALLATION AND PERSONAL SAFETY, IT IS RECOMMENDED THAT TWO
PEOPLE INSTALL THIS PRODUCT.
z
_ .MA_rAG AdmJr31 _'l =JENr, A-aa_ _'_Ji¢ C,._ef
246EdwardsStreet,SE
Cleveland.-ennessee37311
Tei:423-,172-3333
Fax:423-s78-67;0
MOUNTING SPACE
Your Over-the-Range microwave oven requires mounting space on a wall as shown. See Figure 1.
1. A minimum of 30" between wall hung side cabinets is required for installation. Make sure the bottom edge
of the top cabinet is at least 66" from the floor and 30" from the cooking surface.
2. For easier access to the hood lamp, the bottom of the microwave oven should be at least 2" above the range
backsplash.
3. If you are going to vent your microwave oven to the outside, see Step 4 for exhaust duct preparation.
4. If the space between the wall hung cabinets is greater than 30:, a Filler Panel Kit may be used to fill the
gap between the Over-the-Range microwave oven and the wall hung cabinets. Your Use and Care Book con-
tains the kit number for your model.
5. For oven installations beneath smooth, flat cabinets, exercise care and follow the instructions on the cabinet
template for power cord clearance. 30" OR MORE
:OOKING
SURFACE
2-
66" OR MORE
FROM FLOOR
STEP 2
FIG. 1
I. Prepare the unit according to this instruction.
2. Read mounting information on this instruction and prepare top cabinet and wall.
3. Prepare exhaust duct if required.
4. Mount the bracket assembly to wall.
5. Install the unit.
6. Insert three screws (4x65mm) with fiat washer through top cabinet bottom and tighten to top of the unit.
7. Secure the oven bottom to the wall with a bolt and rectangular washer (accessed through the bottom grease
filter openings) of the left side.
L
MA'_TAG Admiral )'1 =JENN-A]I:_ "_,'_ia¢Ji¢ C,"1¢1_
240EdwargsStreeL SE
Cleveland,Tennessee37311
Tel:423-472-3333
Fax:423-478-6710
STEP 3
INSTALLATION HARDWARE
You will find the installation hardware contained in a box packed with the unit.
NAME QUANTITY
I. Wood S_rew 4x50 mm 4
I _ .............. P 4 @ 2. Toggle Bolts (and spring loaded nuts) 3/16 inch 5
3. Screw {4 set_-3 bolts each) 3
4. Rat Washer 3
2 5 -- 5. Grommet 2
6. 28" Piece of Foam Tape 2
6 '_ ' 7. Rectangular Washer I .
3
7 _ STEP 4
HOOD EXHAUST DUCT
Outside ventilation requires HOOD EXHAUST DUCT. Read the following carefully.
EXHAUST CONNECTION: The hood exhaust has been designed to mate with a standard 3 1/4" x 10" rect-
angular duct. If round duct is required, a rectangular-to-round transition adaptor must be used. Do not use
less than 6" diameter duct.
REAR EXHAUST: If rear or horizontal exhaust is to be used, care should be taken to align exhaust with
space between studs, or wall should be prepared at the time it is constructed by leaving enough space between
wall studs to accommodate exhaust.
MAXIMUM DUCT LENGTH: For satisfactory air movement, the total duct length of 3 1/4" x 10" rectan-
gular or 6" diameter round duct should not exceed 140 equivalent feet.
ELBOWS, TRANSITIONS, WALL AND ROOF CAPS, ETC., present additional resistance to airflow and
are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the
total duct length, add the equivalent lengths of all transitions and adaptors plus the lengths of all straight duct
sections. The diagram below shows the approximate feet of equivalent length of some typical ducts. See Fig-
ure 2.
TRANSITIONADAI_fOR
5 FT
WALL CAP 9O"ELBOW
40 FT _0 FT
45"ELBOW _" ELBOW 45"ELBOW ROOFCAP
5FT 25FT 5FT 2_FT
FIG.2
_'_4A'frAG Adm3rallCl _m_',_SNN_=J. "_Magic Chef
240EdwarasS[reet,SE
Cieveiand.Tennessee37311
Tet:423472-3333
7ax:423478-67!0
STEP 5
PREPARATION OF PRODUCT
Use a portion of the carton or some other material to protect the outer case from being damaged. Stand oven
on its control panel side as shown in Figure 3.
To remove rear mounting plate from your microwave oven follow these steps: REAR MOUNTING
A. Remove the 2 SCrews from the rear mounting plate as shown in Figure 3. PLATE
B. Remove bracket. _ _ /
,r
, i
*
11."
_' _ _ FIG, 3
Your 0ver-the-Range microwave oven is designed for adaptation to the following three types of ventilation.
Select the type of ventilation required for your installation and proceed to the appropriate section.
A. Outside Exhaust (Vertical)
B. Outside Exhaust (Horizontal)
C. Recirculating (Non-Vented Ductless). Charcoal Filter Accessory Kit is Required. See your
Use and Care Book for kit number.
NOTE: This product is shipped assembled for top exhaust, except for non-vented models.
Before you install this product, remoee the adhesive tapes on the exhaust adaptor, grease filters and
power supply cord.
ADAPTING BLOWER FOR EXHAUST
A. OUTSIDE EXHAUST (VERTICAL). In some cases adjustments may need to be made to assure proper
alignment with your current exhaust duct.
1. Remove the exhaust adaptor from blower plate by removing the damper and hold both sides of
exhaust adaptor and twist it diagonally. See Figure 4. The gap between the blower plate and
exhaust adaptor will allow removal of the exhaust adaptor.
2 TWIST EXHAUST
ADAPTOR AND
REMOVE FIG. 4
[] MAYI'AG Admiral 7] =_t_JENN-A]R _¢]llacj_¢ C,'let
240EdwardsS[reet.SE
Cleveland,Tennessee37311
Tei:,_23-472-3333
Fax:423-478-6710
Save damper and exhaust adaptor for later replacement. To replace, set exhaust adaptor in place
and twist again to insert flaps into retainer slits and square up the exhaust adaptor, replace the
damper. The adaptor is to be connected to the wall cap of house exhaust pipe.
2. For front-to-back or side-to-side adjustment of exhaust duct, slide top portion of exhaust adaptor
as needed. See Figure 5.
PROCEED TO STEP 6.
B. OUTSIDE EXHAUST (HORIZONTAL) (EXCEPT HIGH CAPACITY EXHAUST MODELS)
1. Remove the exhaust adaptor from blower plate by removing the damper and hold both
sides of exhaust adaptor and twist it diagonally. See Figure 4. The gap between the blower
plate and exhaust adaptor will allow removal of the exhaust adaptor.
2. Remove and save the seven screws which hold blower plate to oven. See Figure 6.
3. Lift off blower plate. See Figure 7. Remove two screws on rear of oven and save.
FIG. 7
[] MA_rA6 Admiral 7| IJENN-_ _¢Jic C_|
Loading...