Maytag 4450269 Installation Manual

Quick Reference

Table of Contents:

Pages

q

1 Product dimensions

q

1 Cutout dimensions

q

Before you start

cl

2 Electrical requirements

m 131 Installation steps 1

If you need assistance:

Check your Use and Care Guide for a toll-free number to call or call
the dealer from whom you purchased this appliance. The dealer is
listed in the Yellow Pages of your phone directon/ under
“Appliances - Household - Major - Service and Repair.”

Call when you:

q

Have questions about range installation or operation.

q

Need to obtain the name and number of an authorized service

company.

When you call, you will need:
l7J The range model number:

l7J The range serial number:
Both numbers are listed on the model/serial rating plate, located on

the oven door or on the oven frame.

30-314”

recessed

height

from

underside
of cooktop
to support

slats

28-5132” oven

recessed widt

Your safety and the safety of others is very
important.
We have provided many important safety messages in this
manual and on your appliance. Always read and obey all
safety messages.

q

!

This is the safety alert symbol.
This symbol alerts you to hazards that can kill or
hurt you and others. All safely messages will be

preceded by the safety alert symbol and the word “DANGER”

or “WARNING”. These words mean:

You ~JHJ be killed or
seriously injured if you
don’t follow instructions.

You can be killed or
seriously injured if you
don’t follow instructions.

All safety messages will identify the hazard, tell you how to
reduce the chance of injury, and tell you what can happen if
the instructions are not followed.

/ L

Important: Observe all governing codes and
ordinances. Failure to meet codes and ordinances
could lead to fire or electrical shock.

Proper installation is your responsibility. Have a qualified
technician install this range.
Range location should be away from strong draft areas,
such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance.

Recessed installation area must provide complete

depth

enclosure around the recessed portion of the range.
Electrical ground is required. See “Electrical requirements.”
IMPORTANT: Some cabinet and building materials are not

designed to withstand the heat produced by the oven for
baking and self-cleaning. Check.with your builder or cabinet
supplier to make sure that the materials used will not
discolor, delaminate or sustain other damage.

Range support surface MUST be solid, level and flush with
bottom of cabinet cutout.

Countertop preparation:

If countertop thickness is

Front edges: You may need to

more than l-1/2” inches

shave or cut the trim of formed

thick: Countertop must be

or metal front-edged

notched as shown to avoid

countertops to clear the 30”

damaging the oven control

width of cooktop.

panel.

w * in;;;,

30-l 18”

\

If countertop extends more
l-1/8” beyond cabinet front:
Notch countertop as shown
to clear oven control panel.

notch width
both sides

cabinet

wall

\

floor

\

13” max. upper

**F r Minimum

1 cl arances to the
top of cooktop see
Note.

--------

Side view of
cabinet cutout

**Note: 24” min. when bottom of wood or

metal cabinet is protected by not less than
l/4” flame retardant millboard covered
with not less than No. 28 MSG sheet steel,

0.015” stainless steel, 0.024” aluminum or

0.020” copper.
30” min. clearance between the top of the

cooking platform and the bottom of an
unprotected wood or metal cabinet.

Copies of the standards listed may be obtained

l

National Fire Protection Association
Batterymarch Park

from:

Top view of

i -I rz-

max.

countertop

thickness

/9 ~~~~~~xE~evel

frond to back and with
each other.

Top of countertop
Note: countertop
must be level
across front and
front to back.

Locate electrical

Do not seal range to side cabinets.
When installing a cooktop under existing cabinets and the

installation does not meet the minimum cabinet clearances.
Install a range hood above the cooktop to avoid burn
hazards.

It is the customer’s responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA
70 - latest edition*, and all local codes and ordinances.

Mobile home installation

The installation of this range must conform to the
Manufactured Home Construction and Safety Standards,
Title 24 CFR, Pat-t 3280 (formerly the Federal Standard for
Mobile Home Construction and Safety, Title 24, HUD, Part

280); or when such standard is not applicable, the Standard
for Manufactured Homes Installations (Manufactured Home
Sites, Communities and Setups), ANSI A225.1/NFPA 501A,
or with local codes.*

When this range is installed in mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the
standards listed above.

Four-wire power supply cable must be used in a mobile
home installation. The appliance wiring will need to be
revised. See four-wire electrical connection, Page 3.

Tools needed:

4

112” dia.

b

router bit

Parts supplied:

-@I3
8

=I=

r

2 screws

2 door removal pins

Ouincy, Massachusetts 02269

Page 1

Front view of
cabinet cutout