ASSEMBLY INSTRUCTIONS
TALON TABLES
NOTE: Please count and inspect all pieces before disposing of any carton or packing materials.
All units consist of 2 cartons consisting of the following.
TOP CARTON
REF# QTY. DESCRIPTION PART NO.
1 1 Top CALL ~~**
When ordering components, specific color and/or size information may be required.
Contact a Mayline Customer Service Representative. 1-800-822-8037
BASE CARTON
REF# QTY. DESCRIPTION PART NO.
2 1 Base Assembly CALL ~~**
HARDWARE BAG (Part No. 8200355*)
REF# QTY. DESCRIPTION
E5 2 Top Mounting Brackets
E6 8 Screw, 1/4-20 x 3/4
E7 2 Plastic Inserts
HARDWARE BAG (Part No. 610236*)
REF# QTY. DESCRIPTION
E1 2 Plastic Leg Clip
E2 4 Screw, #10 x 5/8
E3 2 Ganging Bracket
E4 4 Knob, 1/4-20 x 1/2
** Denotes Color Code
~~Denotes Size
* Individual Items, Order by part number.
Tools Required for Assembly
Allen Wrench 5mm or 3/16", Allen Wrench 4mm or 5/32", Hammer, Phillips Screw Driver
Note: A Magnetic or Power Driver may be used to assist in assembly.
P/N REV 10 05/12/09
(1)
1. Begin Assembly by Flipping Base upright. Rotate top tube at approximately 90° from the modesty panel
as shown in Fig. #1. Begin assembly by locating the Top Mounting Brackets (E5) and inserting them into
the round leg tube as shown in Fig. #2. Caution: Correct rotation and insertion is critical to proper operation
of the unit.
2. With a 5mm or 3/16" Allen Wrench firmly tighten the screw in the top of the Top Mounting Bracket. The
compression fitting can not be over tightened by hand.
INCORRECT INSERTION CORRECT INSERTION
(2)
FIG. #2
3. Place the Top (1) face down on a clean, flat surface. Attach Plastic Inserts (E7) by aligning the stubs
with the pre-drilled holes in the Top. Tap firmly with a hammer until inserts are tight against the Top. See
Fig. #3
4. Attach Leg Clips (E1) into the pre-drilled holes in the Top using Screws (E2). See Fig. #3
5. Position the Base Assembly as shown in Fig #4. With a 4mm or 5/32" Allen Wrench install eight Screws
(E6) through the Mounting Bracket (E5) into the metal inserts in the Top. Do Not tighten at this time. Adjust
the frame so the Locating Pin properly seats itself into the center of the locating hole in the Top. See Fig.
#5. Return to the eight Screws (E6) and tighten at this time. Caution: Over tightening may cause damage
not covered by warrantee.
FIG. #3
FIG. #4
FIG. #5
6. Attach Ganging Brackets with tables in upright, leveled and approximate position. Insert
Knobs (E4) through the Ganging Brackets (E3) into the metal inserts in the Top. Do not tighten
Knobs at this time. See Fig. #6
7. Rotate the Ganging Bracket (E3) under the Knob (E4). Tighten Knobs. See figure #7.
FIG. #6
(3)
Adjustable Height Base Operation
Units with the adjustable height base adjust with the lever
located just to the inside of each leg frame. Gently pushing
the lever up to the top will release the mechanism and the
table should elevate. To lower, gently push up on the lever
with one hand and with the other hand simultaneously push
down on the desk top to the desired height. Excessive force is
not required to activate the levers and may result in damage
as well as trying to activate the lever in any other manner.
Folding Instruction
1. To begin the unfolding process the unit must first be in a
vertical position. See illustration #1 and #2
2. With the Talon table located in the vertical position, stand
on the side shown in illustration #2 and raise the top as
shown.
3. Holding the top in an elevated position, open one of the
legs until it reaches INITIAL POSITION. At this point you will
hear a "click" that will indicate the locating pin has secured
the top in the correct position. Repeat for opposite leg.
4. The Talon table must NEVER be assembled or
disassembled in the position shown in illustration #4.
Attempting to do so will result in severe damage to the table.
BASE WARRANTY PARTS IDENTIFICATION NOT INCLUDED IN ASSEMBLY
REF# QTY. DESCRIPTION PART NO. NOTES
3 2 Top Tube Cap. 2073054L *
4A 2 Locating Pin Assy. 8200230M * (Tube Design Frame)
4B 2 Locating Pin Assy. 8200230 * (Die Cast Arm Frame)
5 2 Shoe Assy. 8200235M * (2 Complete Shoes & Screws in one Bag)
6 2 Toe Cap Screw 8200213 *
7 2 Toe Cap Leveler 8200214M *
8 2 Toe Cap 8200215M *
9 2 Toe Cap Pin 8200212M *
10 2 Pneumatic Handle 8200248 * (Adjustable base only)
11 2 Handle Bracket 8200245 * (Adjustable base only
12 2/Shoe Screw For Shoe Assy. 8200232 *
13 1 Wheel Assy. 8200264 *
Not Shown.
* Individual Items, Order by part number.
(4)
Loading...