ASSEMBLY INSTRUCTIONS
TRANSACTION SINGLE STARTER
NOTE: Please count and inspect all pieces before disposing of any carton or packing materials.
COMPONENTS:
Item # QTY. DESCRIPTION PART #
1 1 LEG, RIGHT HAND A8070**
2 1 LEG, LEFT HAND A8069**
3 1 BEAM ASSEMBLY Call~~**
4 1 TROUGH SIDE Call~~**
5 1 TROUGH SIDE, SINGLE Call~~**
When ordering components, specific color and/or size information may be required.
Contact a Mayline Customer Service Representative. 1-800-822-8037
Item # QTY. DESCRIPTION PART #
6 1 PAN Call~~**
7 1 WORK SURFACE Call~~**
8 0/2/3 ACCESS PANEL Call~~**
9 2 OUTER LEG PANEL TASEP**
10 2 INNER LEG PANEL B8223**
** Denotes Color Code
~~Denotes Size
HARDWARE BAG (PART No. A8077)
* for individual item, order that part number
Item # QTY DESCRIPTION PART #
E1 4 TUBE INSERT, 5/16-18 T139*
E2 4 GLIDE Q608*
E3 15 SCREWS #10-32 x 1/2" X204*
E4 6 WASHER, EXT STAR #10 W38*
E5 14 SCREW #10 x 3/4 X11*
E6 3 PLUG, SQUARE HOLE F782*
E7 2 SLAM LATCH Q643*
E8 1 BUSHING F764*
E9 8 RATCHET FASTENER F483*
E10 4 PINE TREE CLIP F529*
(1)
WORK SURFACE HARDWARE
TAST48, TAST60, TAST72:
SINGLE TRANSACTION "without" ACCESS PANELS
No additional hardware is required with these products.
TAST48S
SINGLE TRANSACTION STARTER "with" ACCESS PANELS
HARDWARE BAG (PART No. A8116)
Item # QTY DESCRIPTION PART #
E11 2 ANGLE, MOUNTING B8267*
E12 5 SCREWS #10-32 x 1/2" X204*
E13 2 DOWEL PIN. PLASTIC F783*
E14 6 2" X 2" SPACER E544*
* for individual item, order that part number
TAST60S, TAST72S
SINGLE TRANSACTION STARTER "with" ACCESS PANELS
HARDWARE BAG (PART No. A8117)
* for individual item, order that part number
Item # QTY DESCRIPTION PART #
E11 4 ANGLE, MOUNTING B8267*
E12 9 SCREWS #10-32 x 1/2" X204*
E13 8 DOWEL PIN. PLASTIC F783*
E14 8 2" X 2" SPACER E544*
NOTE:
If the desired configuration utilizes multiple adders,
substitute an Adder Leg (TASAL**) for the right hand
starter leg.
1. Install tube inserts (E1) into legs (1 & 2).
NOTE: Substitute Adder Leg (TASAL**) for Right Hand Leg (1)
when final configuration utilizes multiple adders.
2. Screw glide (E2) into inserts.
(3)
NOTE: The illustrations shown here reflect a 60"W or
72"W table. If installing a 48"W, part quantities may
vary.
NOTE: If installing a table without access panels (8),
proceed to Step 4.
3. Attach mounting angles (E11) to trough side (4)
using screws (E12).
4. Install screws (E3) to the inside of leg (the side opposite gusset
OR ADDER LEG, IF
flange), leaving approximately 1/8" between screw head and leg tube.
5. Using slots in trough sides (4, 5), hook trough sides onto screw
heads on both legs. DO NOT TIGHTEN SCREWS.
GUSSET FLANGE
(Starter leg only)
REQUIRED
ADDER LEG
IF REQUIRED
NOTE: If installing a table without access panels (8),
proceed to Step 7.
6. Attach mounting angles (E11) to beam (3) using
screws (E12)
7. Install beam (3) from rear, sliding onto legs.
Secure beam (3) with screws (E3) and washers (E4).
8. Insert bushing (E9) into trough side (4).
9. Tighten all screws (E3) at this time.
(4)
10. Lay pan (6) onto trough sides flanges (4 & 5).
Secure pan (6) to trough sides (4 & 5) using pine
tree (E10)
11. Install slam latch (E7) into slot in the inner leg
panel (10) as shown.
12. Insert tabs in the bottom of inner leg panel
(10) into slots in foot. Rotate inner leg panel (10) up
so that slam latch catches flange on pan (6).
13. Install outside leg panels (9) by aligning the
one flange with the inside edge of the tube and
applying pressure to create a curve in the end panel
that allows 2nd flange to slide inside edge of tube.
14. Insert square hole plugs (E6) and ratchet
fastener (E9) into holes in beam. NOTE: This step
should be done after privacy panels or monitor
posts are installed in the beam.
For tables "WITHOUT" Access Panels (8).
15. Position work surface (7) without access panels and
secure with screws (E5).
For tables "WITH" Access Panels (8).
15. Insert dowels (E13) into holes in access panels (8) as
shown below. NOTE: For 48" W tables use the positions
shown in the far left and right of the view below.
16. Lay access panels (8) onto table frame so that dowels
engage holes in mounting angles.
17. Insert spacers (E14) between access panels and work
surfaces as shown (2 per access panel).
18. Position work surfaces and secure with screws (E5).
Remove spacers.
Install dowels (E13) in
the positions shown
Underside of Access Panels
(5)
Loading...