Page 1
ASSEMBLY INSTRUCTIONS
(1)
RANGER STEEL FOUR-POST TABLES
NOTE: Please count and inspect all pieces before disposing of any carton or packing materials.
When ordering components, specific color and/or size information may be
required. Contact a Mayline Customer Service Representative. 1-800-822-8037
COMPONENTS:
REF. # QTY. DESCRIPTION PART No.
1 1 R.H. END ASSEMBLY CALL~~**
2 1 L.H. END ASSEMBLY CALL~~**
3 1 FRONT RAIL CALL~~**
4 1 REAR RAIL CALL~~**
5 1 FOOT RAIL CALL~~**
6 1 DUST COVER CALL~~
7 2 TILT ROD ASSEMBLY A315
HARDWARE BAG:
REF. # QTY. DESCRIPTION PART No.
E1 2 LOWER HINGE B195*
E2 2 UPPER HINGE B194*
E3 4 10-24 x 3/8 X147*
MACHINE SCREW
TABLE w/o DRAWER -
TABLE
PART No. A7680
*for individual item, order that part number
REF. # QTY. DESCRIPTION PART No.
E8 10 10 x 3/4 SCREW X11*
E9 2 KNOB K13*
E10 2 WASHER W30*
E4 4 10-24 KEPS NUT T2*
E5 12 1/4-28 x 3/8 X156*
MACHINE SCREW
E6 12 1/4-28 KEPS NUT T25*
E7 11 8 x 5/8 SCREW X140A*
E11 2 5/16-18 X 1/2 RD. X157*
HD. MACHINE SCREW
E12 2 TILT ROD GUIDE B160*
OPTIONAL COMPONENTS AND HARDWARE
are listed on the last page of this sheet.
Page 2
Center Support.
E6
(2)
E5
1. Place the two End Assemblies (1 & 2)
upside down. Position the Front Rail (3)
with the larger of the two flanges toward the
floor. Position the Rear Rail (4) with the
Dust Cover attachment holes toward the
floor. Secure these Rails to the End
Assemblies with two Screws (E5) and two
Nuts (E6) per leg. DO NOT tighten screws
at this time.
2. Position the Foot Rail (5) with flat
surface toward the floor. Attach the Foot
Rail to the End Assemblies with four Screws
(E5) and Nuts (E6). TIGHTEN all screws
from steps 1 & 2 now.
3. Turn assembled table to an upright
position. MAYLINE recommends that two
people perform this task.
4. Fasten one Tilt Rod Guide (E12) to each
side of the table using one Bolt (E11) and
one Washer (E10) per guide. DO NOT
tighten completely.
ASSEMBLY INSTRUCTIONS:
OPTIONAL DRAWERS
1. Separate the Drawer Slides (9) into two pieces.
Extend the Slide to the full extension. Remove the
smaller portion (9B) by pressing the plastic release
and pulling.
5. Insert Tilt Rod Assembly (7) through hole
in Guide and tighten in place with Plastic
Knob (E9).
6. Position the Lower Hinge (E1) with the
slot hanging beyond the front of the table.
Align the holes and attach with Screws (E3)
and Hex Nuts (E4). Tighten these screws.
NOTE: If your product is not equipped with
the OPTIONAL Drawers proceed to the
final page of this Instruction Sheet for Top
Installation.
"PRESS"
PULL
Begin
"HERE"
2. Attach the large Slide portion (9A) to the Center
Support (8) using two Screws (E16). Begin attaching
the Slide using the large 'Horizontal' slot in the last
mounting tab.
NOTE: If you are installing the Optional Shallow
Drawer, repeat step #2 on the opposite side of the
TOOL
DRAWER
SLIDE
SHALLOW
DRAWER
SLIDE
Page 3
3. Attach one large Slide portion (9A) to the
(3)
brackets on the R.H. side of the table using two
Screws (E16). Begin attaching the Slide using the
large 'Horizontal' slot in the last mounting tab using
the lower set of holes for Tool Drawer installation.
NOTE: If you are installing the Optional Shallow
Drawer, repeat this procedure on the L.H. side of
the Table using the upper set of holes.
4. Attach the smaller Slide portion (9B) to each
side of the Drawer body using three Screws (E17)
and three Acorn Nuts (E18). Begin attaching the
Slide using the 'Vertical' slot in the first hole cluster.
NOTE: If you are installing the Optional Shallow
Drawer, repeat Step 4, beginning at the same
vertical slot in Slide portion 9B as on the tool
drawer assembly.
Begin "HERE"
E16
R.H. Side - Tool Drawer
Begin "HERE"
5. Install the Drawer Pull (E15) onto the Tool
Drawer head using Screws (E13).
6. Install the assembled Center Support into the
Base. Attach the Support with two Screws (E13)
and two Nuts (E14) per rail.
7. Install the drawer/s into the assembled table.
'OPTIONAL'
Shallow Drawer Slide
L.H. Side - Shallow Drawer
Begin "HERE"
Begin "HERE"
Page 4
TOP INSTALLATION:
(4)
1. Lay the Dust Cover (6) onto the table. Align
the holes in the Dust Cover with the holes in the
Rails and attach with Screws (E7).
2. Align the holes in the Upper Hinge (E2) with
the holes in the underside of the Top. Attach the
Hinge using three Screws (E8) per Hinge.
3. Hold the Top in a vertical position and insert
the ears of the Upper Hinge (E2) into the slots of
the Lower Hinge (E1). Lower the Top.
4. Attach the Tilt Rods (7) to the Top using two
Screws (E8) per Tilt Rod.
E2
E8
E8
5. Paper apron is shipped in the "flush" position
from the factory. Apron may be reversed to
provide a "LIP".
6. To change apron position, remove and retain 4
screws and spacers that attach apron to top.
7. Flip apron 180° and align holes in apron with
holes in edge of top. Reattach the apron using
the 4 screws and spacers.
Page 5
OPTIONAL COMPONENTS:
(5)
The following components are in addition
to the TABLE components.
TOOL DRAWER ACCESSORY:
REF. # QTY. DESCRIPTION PART No.
8 1 CENTER SUPPORT B7469**
9 2 DRAWER SLIDE B6361**
10 1 TOOL TRAY F187
11 1 TOOL DRAWER A7553**
SHALLOW DRAWER ACCESSORY:
12 2 DRAWER SLIDE B6361**
13 1 SHALLOW DRAWER CALL~~**
** Denotes Color Code
~~Denotes Size
OPTIONAL COMPONENTS HARDWARE:
The following hardware is in addition to the Table Hardware .
HARDWARE BAG:
TOOL and SHALLOW DRAWER ACCESSORIES:
REF. # QTY. DESCRIPTION PART No.
E13 6 #10-24 x 3/8 SCREW X147*
E14 4 #10-24 KEPS NUT T2*
E15 1 DRAWER HANDLE Q35*
E16 8 #8-32 x 3/8 THRD. CUTTING SCREW X247*
E17 12 #8-32 x 5/16 MACHINE SCREW X384*
E18 12 #8-32 ACORN NUT T129*
TABLE with DRAWERS -
PART No. A7681
Loading...