Page 1
re l
o
ffice
PARTS LIST
Aberdeen Series
TM
Conference Table 216" x 48"
Model No. ACTB18
Name Part
A
REALS004
Wood Dowel
B
REALS003
Cam Post
Qty.
HB
24
HB
38
HB
C 38 2
REALS001
Cam Fastener
HB
Spare
Qty
1
2
F
H
PartName
REALS099
Grommet
REALS167
Plate
REALS118
Center Plate
HB
HB
Qty.
3
4G
2
Spare
Qty
ASSEMBLY INSTRUCTIONS
CALL 1-800-822-8037 FOR ASSISTANCE
P/N ACTB18 REV 04 07/22/14
www.mayline.com
D
REALS102**
E
Cam Sticker
REALS067
Leveler
HB
238
6
J
REALS043
M6 x 15mm
ACBT18HB
Items with HB are in
48 2
hardware box
1
Page 2
Name Part
PARTS LIST
Qty.
DO NOT assemble table with top to floor. Table must be assembled in
1
an upright position only.
Insert Wood Dowels (A) and Cams(C) into top edge of each Modesty
2
PartName
Qty.
Panel (S). Insert Wood Dowels (A) and Cams (C) into the end of each
Modesty Panel (S). Install Cam Posts (B) into threaded inserts in Table
Legs (M&P). Install Leveler (E) and insert Cams (C) into the Table
Legs (M&P). Secure Modesty Panels (S) to Table Legs (M&P) by
turning Cams (C).
L
ABT18L**
M
Middle Table Leg
N
ABT18N**
Middle Top
2
Top
1
ACLG1**
1
P
ACLG**
Table Leg
2
4S
ACM18**
Modesty Panel
Items with HB are in the hardware box
**Denotes Color Code
IMPORTANT!
Review ALL instructions before beginning assembly. These
instructions are provided to avoid problems that may occur from
improper assembly or installation. Mayline and/or its distributor
are not responsible for failure resulting from improper assembly
or installation of this product. Moreover, all warranties are void
for failure to follow these assembly instructions.
S
P
NOTE: The arrow on the face of the Cam (C)
should point towards the Cam Post (B) for
proper alignment.
M
S
2 3
Page 3
Insert Wood Dowels (A) and Cams(C) into top edge of each Modesty
3
Panel (S). Insert Wood Dowels (A) and Cams (C) into the end of each
Modesty Panel (S). Install Cam Posts (B) into threaded inserts in Table
Legs (M&P). Install Leveler (E) and insert Cams (C) into the Table
Legs (M&P). Secure Modesty Panels (S) to Table Legs (M&P) by
turning Cams (C).
Install Cam Posts (B) into threaded inserts into the underside of each
4
Top (N). Attach Plates (H & G) to the underside of Top (N) using
Screws (J).
S
S
M
P
NOTE: The arrow on the face of the Cam (C)
should point towards the Cam Post (B) for
proper alignment.
C
P
S
S
B
P
G
N
H
B
P
A
4
5
Page 4
Place each Top (N) onto the base. Secure Top (N) to base by turning
5
Cams (C). Insert Grommet (F) into Top (N). Apply Cam Stickers (D) to
all exposed Cams (C).
N
Install Cam Posts (B) into threaded inserts into the underside of each
6
Top (L).
L
6
7
Page 5
Place each Top (L) onto the base. Fasten tops (L) together using
7
Plates (G, H) and Screws (J). Secure Tops (L) to base by turning Cams
(C). Insert Grommet (F) into Tops (L). Apply Cam Stickers (D) to all
exposed Cams (C).
L
N
L
M
S
P
P
8
Loading...