May Cheong Toy Fty 07188RC27 Users Manual

Maisto Radio Control Project 66

y

The packaging has to be kept since it contains important information.

Contents:

Project 66 x 1
Transmitter x 1
Transmitter antenna x 1
Instruction Manual x 1

Project 66: Installation of Batteries

1. Switch the power OFF.

2. Open the battery cover using a screwdrive.
Take out the battery compartment and install six new 1.5V AA

3.
batteries with correct polarity (+/-) as shown inside the battery

copartment.
Insert the battery compartment back and fastern the battery cover.

4.

Transmitter: Battery and Antenna Installation

1. Switch the power OFF.

2. Open the battery cover.
Install a new 9V battery with correct polarity (+/-) as shown

3.
inside the battery compartment.

4. Close the battery cover.

5. Screw the antenna into the transmitter securely.

Warning!Do not aim at e

Warning!

There are hazardous of using projectiles other

es or face

than those supplied or recommended by the manufacturer.

How to play:

1. Fully extend the antenna of the transmitter.

2. Match the transmitter with the Project 66 Channel (Channel A or B or C).

3. Switch ON the transmitter, the transformation button will light up.

4. Switch ON the Project 66.

5. Use the transimitter's levers and buttons to control the movement, transformation and shooting of Project 66

A. Movement

i. Push the left / right lever up or down to move the Project 66.

B. Transformation

i. Press the transform button to transform Project 66 into different mode.

C. Shooting

i. Transform into attack mode and Insert 5 missiles into the launcher.
ii. Press the shoot button to shoot missiles one by one.

Performance Tips:

1. Do not drive on grass, sand, carpet or go through water.

2. Do not drive in windy or rainy weather.

3. Avoid colliding with hard surfaces.

4. Switch OFF the Project 66 and transmitter when not in use.

5. Remove all batteries from the Project 66 and transmitter when not in use.

6. Fully extend the antenna for best performance and do not point the antenna toward the Project 66.

7. The operating range can be affected by a variety of factors:
a) Weak transmitter battery, or under-charged batteries.
b) Interference from other items that emit radio frequency signals such as another R/C item on the same frequency,

CB radios, cordless phones, high voltage transformers, etc.

8. Make sure all missiles insert into the launcher tightly.

9. Check if there is foreign object inside the Project 66 before transformation each time.

Cautions :

1. Do not aim at eyes or face.

2. Do not use projectiles other than those supplied or recommended by the manufacturer.

3. Do not pick up the Project 66 while its in motion.

4. Do not pick up the Project 66 by holding the wind shield or the rear wing.

5. Do not hold the wheels while the Project 66 is moving.

6. Do not bend the wind shield, body and missiles of the Project 66.

7. Do not force to pull missiles out from launcher.

8. Keep fingers, hair and loose clothing away from the wheels.

Battery use :

1. Alkaline batteries are recommended to use.

2. Only batteries of the same or equivalent type as recommended are to be used.

3. Do not mix alkaline, standard or rechargeable batteries.

4. Do not mix old and new batteries or different type of batteries.

5. Non-rechargeable batteries are not to be charged.

6. If rechargeable batteries are used, they are only to be charged under adult supervision.

7. Rechargeable batteries are to be removed from the product before they are charged.

8. Be sure to insert batteries with the correct polarities and always follow the battery manufacturer's instructions.

9. Remove all batteries from the vehicle and transmitter when not in use.

10. Exhausted batteries are to be removed from the product.

11. The supply terminals are not to be short-circuited.

12. Dispose of batteries properly. Do not dispose the batteries in fire — it may cause them to explode or leak
causing injury or damage

FCC Label Compliance Statement:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions :

This device may not cause harmful interference, and

1.