Maxview MXR0024 Instructions Manual

Assembly instructions

Contact:

Helplin e: [phone]
Email: [e-mail]
Web: w ww. max vie w.co.u k

Maxview re serve the right t o change specific ations withou t prior notice
9111307 Iss 2

MXR0024 TV Aerial - 18 Element

Model:

Connecting Coaxial Cable (Not supplied)

1.

Using a shar p knife prepare the Coa xial Cabl e as
shown.

Loosen th e screws on the 2 t erminals i n the
Dipole. F eed the inn er core to one of the
terminal s and the tw isted brai d into the oth er.
Tighten sc rews and clo se Dipole C ap.

2.

12mm

18mm

28mm

Turn on your T V set. Refer to ma nufact urers inst ructio ns to tune you r TV into the availabl e digital/H D/3D
channels. Select a tuned-in channel. Next, carry out the following procedures:

1. Turn your aeri al to the LEF T until you los e the picture (if alone t urn the vol ume up and tu rn until you hear a
reduction in sound quality).

2. Remembe r this posit ion and tur n your aerial to the RIGH T until you lose the pic ture/sound ag ain.

3. Now point th e aerial in the centre of the se two points and you w ill receive op timum recep tion.

Digital & H D reception:

Reception of d igital terrestria l TV (DTT) sig nals is subject to:

1. Use with a DTT se t top box or inte grated T V with digit al tuner/receiver

2. Satisfa ctory si gnal qual ity from DT T transmitter

To receive terres trial HD ch annels you w ill requi re the follow ing:

1. An HD ready T V

2. Freeview HD re ceiver or TV with integ rated Freev iew HD tuner/receive r

3. HD signals m ust be transmitte d in your loc al area. Visi t www.freev iew.co.uk for more informat ion.

Safety warnings:

> Before sta rting in stallati on check st ructure is sound an d check for hidden ele ctrical wiring o r plumbin g.
> When work ing on installatio ns outsid e, beware of overhead power l ines.
> Observ e safe work ing prac tices, tread c arefully a nd ensure ad equate lig hting is ava ilable in l oft/roof space .
> Always follow manufacturer’s operating and safety instructions before using tools and/or equipment.
> Ladder s afety - alway s read and follow the manu factur er’s instru ction label affixe d to the ladde r.
> Ensure cab le is correc tly routed before fixin g into positi on, taking care not to ove r tighten ca ble clips.
> This prod uct may cont ain small pa rts - keep out of reach of ch ildren.
> After ins tallatio n make regula r maintenance check s.
> If in doubt co nsult a qua lified or pro fessional a erial installer.

Aligning your aerial

Polarisation

Tip: Look at o utdoor aerials
in your area to s ee which
directi on to point yo ur
aerial for best reception.

(Note different
model illustrated for
example only)

Vertical mounting
recommended for
Relay TV transmitters.

Horizontal mounting
recommended for
Main TV transmitters.

Pack contents check

A. Reflec tor Plate x 1
B. Suppor t Arm x 1
C. Dipol e x 1
D. Joining P late x 2
E. Suppor t Arm Bracket x 4
F. Washer x 4
G. M5 Nut x 4
H. M5 x 25mm Sc rew x 4

I. Screw x 1
J. Mast Cla mp x 1
K. Rear Boo m Assemb ly x 1
L. Front Boo m Assembly x 1

B

A

D

J

F

G

H

1.

Join the 2 pi eces of boom t ogether us ing the
joining p late, M5 x 25mm sc rews M5 nuts and
5mm Shake Proo f Washers.

2.

3.

Assembly

Screw the Di pole firm ly to the Boom .

Fit the sup port ar m to boom of the a erial usin g the four joining pla tes. Secu re with nuts a nd bolts.

I

E

C

4.

Slide on an d firmly pus h down the Refl ector onto
the groove of the Reflector Bung.

5.

Attach ae rial to suit able mast (not i ncluded)
using the su pplied Mast Clamp.

L

K