WDR-516S
Installation Guide
FCC Compliance Statement
Caution : Any changes or modifications in construction of this device which are not expressly
approved the party responsible for compliance could void the user's authority to operate the
equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications, However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION
1. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
2. Disposal of used batteries according to the general recommendations against the environmental
pollution.
3.
Do not throw the batteries into a fire, and do not heat, short-circuit or attempt to disassemble the
batteries.
4.
Do not attempt to recharge the batteries.
Important Notice
1. Do not place heavy objects on the top of the WDR-516S.
2. WDR-516S is not weatherproof. In case of outdoor use, equip a weatherproof case to protect WDR-
516S from water, moisture, or temperature (higher or lower than specifications). To clean the WDR-516S,
gently wipe the outside with a clean dry cloth.
3. Be sure to use a DC adapter that is provided by DENTEC Corp. Connecting WDR-516S directly to an
AC current will cause electric damages to WDR-516S.
4. Be careful not to drop the WDR-516S. Physical shocks may harm the product. In addition, be sure the
WDR-516S is secured after installation.
5. If WDR-516S does not operate properly, please contact the closest DENTEC distributor for after sales
service. Tampering or disassembling the product will void the warranty.
6. Security surveillance laws may differ for each country. Therefore, please contact the local region first
to avoid any surveillance law violations.
OVERVIEW.................................................................................................................................. 7
1. What is WDR-516S?............................................................................................................ 7
2. Supplied Accessories......................................................................................................... 8
3. Description & Function ...................................................................................................... 9
INSTALLATION AND CONNECTION ....................................................................................... 11
4. Connecting & Running WDR-516S.................................................................................. 11
4.1. Connecting camera.......................................................................................................11
4.2. Connecting Monitor...................................................................................................... 12
4.3. Connecting Audio ........................................................................................................ 12
4.4. Supplying Power.......................................................................................................... 13
5. Running OSD menu .......................................................................................................... 14
5.1. Using menu.................................................................................................................. 14
5.2. Dialogue Box to Edit a Word........................................................................................ 15
6. Setting remote controller ................................................................................................. 16
6.1. Setting remote control DIP switch................................................................................ 16
6.2. Set ID of WDR-516S................................................................................................... 16
6.3. Selecting WDR-516S................................................................................................... 17
6.4. Operable range of remote controller............................................................................ 18
6.5. Loading the batteries into remote controller................................................................. 18
7. WDR-516S Configuration ................................................................................................. 19
7.1. Basic Configuration...................................................................................................... 19
7.2. Advanced Configuration .............................................................................................. 19
7.3. External Storage & Backup Configuration ................................................................... 20
7.4. Internet/Intranet Configuration ..................................................................................... 20
8. WDR-516S Basic Setting .................................................................................................. 21
8.1. Viewing Image ............................................................................................................. 21
8.2. Setting Date & Time..................................................................................................... 22
8.2.1. Time Zone............................................................................................................. 22
WDR-516S Installation Guide
4
Rev 1.0(93/11)
8.2.2. Daylight Saving..................................................................................................... 22
8.2.3. Time Format ......................................................................................................... 23
8.2.4. Date...................................................................................................................... 23
8.2.5. Time...................................................................................................................... 23
8.2.6. Apply Date/Time ................................................................................................... 23
8.3. Setting Recording Condition ........................................................................................ 24
8.3.1. Configuration Status ............................................................................................. 25
8.3.2. Channel Status ..................................................................................................... 25
8.3.3. Recording Speed/Quality...................................................................................... 25
8.3.4. Speed(ips) ............................................................................................................ 25
8.3.5. Quality .................................................................................................................. 26
8.3.6. Audio Recording ................................................................................................... 26
8.3.7. Apply..................................................................................................................... 26
9. Connecting and Configuring Sensor .............................................................................. 27
9.1. Connecting Sensor Input ............................................................................................. 27
9.2. Setting Sensor at OSD menu ...................................................................................... 28
10. Connecting & Configuring Relay Out .......................................................................... 29
10.1. Connecting Relay Out .............................................................................................. 29
10.2. Configuring Relay Out.............................................................................................. 30
11. Connecting External Device with Serial Port .............................................................. 31
11.1 . Connecting Text Input Device (ATM / POS / Access Control) .................................. 31
12. Connecting & Configuring Serial Ports for Pan/Tilt/Zoom ........................................ 32
12.1. Connecting Serial Port ............................................................................................. 32
12.1.1. Connecting RS232............................................................................................ 32
12.1.2. Connecting RS485............................................................................................ 32
12.1.3. Connecting RS422............................................................................................ 32
12.2. Configuring Serial Port ............................................................................................. 33
13. Connecting USB Device ............................................................................................... 34
14. Connecting External Storage ....................................................................................... 36
14.1. IEEE1394 Bay.......................................................................................................... 36
14.2. Connecting IEEE1394 Device.................................................................................. 36
WDR-516S Installation Guide
5
Rev 1.0(93/11)
14.3. Available HDD.......................................................................................................... 36
14.4. Registering & Formatting HDD................................................................................. 37
15. Network Monitoring & Managing ................................................................................. 38
15.1. Connecting Ethernet ................................................................................................ 38
15.2. Configuring WDR-516S’s Network Information ........................................................ 39
16. Using WDR Manager ..................................................................................................... 40
16.1. PC System Requirements for running WDR Manager ............................................. 40
16.1.1. Installing WDR Manager ................................................................................... 40
16.1.2. Uninstalling WDR Manager............................................................................... 42
16.2. Configstation ............................................................................................................ 42
16.3. Monitor ..................................................................................................................... 43
16.4. Playback................................................................................................................... 43
APPENDIX ............................................................................................................................... 44
Appendix #1 Installing and Replacing internal HDD .......................................................... 45
Appendix #2 Video Input ...................................................................................................... 50
Appendix #3 Using CD-ROM ................................................................................................ 51
Appendix #4 Specification.................................................................................................... 52
WDR-516S Installation Guide
6
Rev 1.0(93/11)
OVERVIEW
1. What is WDR-516S?
The WDR-516S is a 4-Analog, 12-IP channel network digital video recorder. The WDR-516S can record
and display 4 analog video channels and 12 IP video channels simultaneously. Video, Audio, and Text
Event-Logs are digitized and stored on two internal hard-drives.
Key features
□
Expandable up to 16 channels (4 analog video channels + 12 IP video channels)
□
1 channel audio recording & playback
□
Total 120 ips recording speed (Analogue video 60ips + IP video 60ips)
□
Total 120 ips display speed (Max 60ips over Network)
□
Built-in software multiplexer for all 16 live monitoring channels (1 / 4 / 9 / 13 / 16Ch Mode on
CCTV Monitor as well as PC)
□
Maximum 4TB storage capacity (IEEE 1394 for external HDD)
□
ATM/POS transaction information text recording and search with corresponding video
□
4 pairs of sensor inputs and alarm outputs
□
Built-in hardware motion detection with search function (64-division comparison)
□
Various efficient back-up methods (IEEE 1394(FiWi), USB (V 1.1), Ethernet)
□
PTZ Control (Preset support) via RS 232 and RS 485/RS422
□
User-friendly 32bit True-colored Graphic OSD Menu
□
Dynamic IP (DHCP, Floating IP) support (when xDSL and Cable Modem are used)
□
IR remote controller (User controls PTZ with remote controller)
□
Remote Management Software (WDR Manager)
WDR-516S Installation Guide
7
Rev 1.0(93/11)
2. Supplied Accessories
Unpack and check all the items as below.
1. WDR-516S (1)
3. AC Power Cord (1)
2. DC Power Supply (1)
(110V~220V)
4. CD-ROM (Including WDR Manager) (1)
5. Remote Controller (1)
7. Plug Bracket (1)
6. Guide (2)
8. HDD Fixing Screw (8)
WDR-516S Installation Guide
8
Rev 1.0(93/11)
3. Description & Function
WDR-516S Front
1
3
6
4
2
5
(1) LED
(2) IEEE1394 connecter
(3) Remote controller receiver
(4) USB connecter
(5) Function buttons
(6) Bracket fixing hole for rack mount
WDR-516S Installation Guide
9
Rev 1.0(93/11)
WDR-516S Rear
11
12
13
14
15
(7) Power switch
(8) Ethernet connector
(9) BNC connector for Video input
(10) Audio input / output connector
16
10
17
9
18
7
8
19
20
(11) RS232 connecter (9Pin D-Sub)
(12) Terminal block for RS232 & 422/485
(13) Terminal block for Sensor input
(14) Terminal block for Relay output
(15) Video output for MONITOR or VCR
(16) Video input type/impedance select & remote controller switch
(17) IEEE1394 connecter
(18) USB connecter
(19) Power connector (DC12V)
(20) GND
WDR-516S Installation Guide
10
Rev 1.0(93/11)
INSTALLATION AND CONNECTION
4. Connecting & Running WDR-516S
4.1. Connecting camera
(1) Connect CCTV camera to WDR-516S with BNC cable as shown below.
(2) Set video type (NTSC/PAL) by rear panel’s switch.
<Note>
The video type for all channels should be either NTSC or PAL. NTSC is the standard used in North
America.
(3) Set the impedance control switch for each channel as needed.
<Note>
It may be necessary to configure impedance of video input differently for each channel. For more
detailed information, please refer to “Video type / impedance setup switch” in Appendix #2.
CAMERA
REMOTE
CONTROL
N
Hi-Z
ON
WDR-516S Installation Guide
11
4P
3
2
OFF
Rev 1.0(93/11)
4.2. Connecting Monitor
(1) Connect CCTV monitor to WDR-516S with BNC cable as shown below.
<Note>
WDR-516S has two video output ports ; for Monitor and VCR. The output signals from the two ports
are same and either port may be used.
4.3. Connecting Audio
(1) Connect audio signal to WDR-516S.
WDR-516S Installation Guide
12
Rev 1.0(93/11)
4.4. Supplying Power
(1) Connect power cable to WDR-516S.
(2) Turn on the power switch located on the WDR-516S rear panel.
<Note>
Use the plug bracket to secure the power cable if needed.
<Note>
To connect EARTH, refer to the following picture.
WDR-516S Installation Guide
13
Rev 1.0(93/11)
(1)
(4)
5. Running OSD menu
5.1. Using menu
Press the [MENU] button to open the OSD Configuration Menu.
Main Menu
(2) Sub-menu
(3) Setting Page
Help message
(1) Main Menu Tabs: The selected tab is shown in blue and the related sub-menus will be shown below
the tab. To move to the previous/next Main Menu Tab, use the [◄ or ►] arrow buttons. To move to a
sub-menu, press the [ENTER] or [▼] buttons.
(2) Sub-menu: The selected sub-menu is shown in blue and the related setting page will be shown to the
right of the sub-menu. Use the [▲/▼] arrow buttons to move within the sub-menu list. To move to the
setting page press the [ENTER] button. To exit the setting page, press the [EXIT] button.
(3) Setting Page: The selected item is shown in gray. To move within each page, use the [◄ or ►] or
[▲/ ▼] arrow buttons. Press the [ENTER] button to change the value of a setting. When the setting value
is a word, a dialogue box to edit the word will open. When setting value is a number, it should be set with
using the [◄ or ►] or [▲/▼] arrow buttons. After the value is set, press the [EXIT] button. To exit the
Setting Page, press the [EXIT] button.
(4) Help message: Related information for each menu/setting will be displayed here.
WDR-516S Installation Guide
14
Rev 1.0(93/11)
5.2. Dialogue Box to Edit a Word
There are two methods to set word.
(1) Using number button
Enter the related numbers in order of horizontal/vertical. (For example, in order to select “ C ” , press
[3] and [2] buttons.)
(2) Using arrow button
Select a value using the [◄ or ►] or [▲/▼] buttons. The intersection of the horizontal and vertical bar is
selected value. Press the [►] button to confirm the selected value.
(3) Function word
The following symbols are for executing specific functions:
9
: Enter
: Back Space & delete
: Space
◄ : Move to left
► : Move to right
: Previous Code Page
: Next Code Page
WDR-516S Installation Guide
15
Rev 1.0(93/11)
6. Setting remote controller
6.1. Setting remote control DIP switch
Set the remote control DIP switch to “ON.”
REMOTE
CONTROL
N
4P
ON
OFF
Hi-Z
3
2
1
6.2. Set ID of WDR-516S
When controlling several WDR-516S with one remote controller, set Remote Control ID as follows.
(1) Press [MENU] button.
(2) Select “System” with using [►] button and press the [ENETR] or [▼] button.
WDR-516S Installation Guide
16
Rev 1.0(93/11)
(3) Select “Miscellaneous” from the sub-menu list using the [▼] button and press the [ENETR] button.
(4) Select “Remote Control ID,” and press the [ENETR] button.
(5) Select a value using the [◄ or ►] buttons and press the [EXIT] button.
(6) Press the [EXIT] button to exit the Settings Page and return to Monitor mode.
<Note> Remote Control ID
Up to 16 WDRs can be controlled with a single remote controller.
6.3. Selecting WDR-516S
If several WDRs are set with unique ID numbers, they can be controlled with one remote controller. To
select a specific WDR-516S, press the ID button of remote controller until the 8 LEDs on the front of the
WDR-516S light up and a buzzer sounds.
Press repeatedly
till to select WDR
What you want
Remote Controller
Unselected
Selected
PWR NET
A1 A2
PWR NET
A1 A2
All LED Blink One Time
REC PLAY
A3 A4
REC PLAY
A3 A4
<Note>
Because remote controller ID is sixteen, WDR will correspond.
WDR-516S Installation Guide
17
Rev 1.0(93/11)
6.4. Operable range of remote controller
WDR
6.5. Loading the batteries into remote controller
Remote controller requires two AAA-type batteries.
1. Remove the battery cover.
2. Taking care that the poles(+/-)
3. Replace the battery cover.
are correctly positioned.
WDR-516S Installation Guide
18
Rev 1.0(93/11)
7. WDR-516S Configuration
7.1. Basic Configuration
7.2. Advanced Configuration
WDR-516S Installation Guide
19
Rev 1.0(93/11)
7.3. External Storage & Backup Configuration
7.4. Internet/Intranet Configuration
WDR
WDR-516S Installation Guide
20
Rev 1.0(93/11)
8. WDR-516S Basic Setting
8.1. Viewing Image
After initial start-up, images from Ch.1~4 are displayed in a quad-split screen.
<Note>
If user password is set, a prompt for entering the password will appear.
WDR-516S Installation Guide
21
Rev 1.0(93/11)
8.2. Setting Date & Time
(1) Press [MENU] button, and select “Quick Setup” tab.
(2) Select “Date/Time” and enter the Settings Page by pressing [ENTER].
8.2.1. Time Zone
(1) Select “Time Zone” and press [ENETR] button to configure.
(2) Select a value using the [◄ or ►] button and press the [EXIT] button when finished.
8.2.2. Daylight Saving
(1) “Daylight Saving Time” is only activated for time zones that use Daylight Savings. If activated, press
[ENTER] to enter a new value.
(2) Select “On/Off” using the [◄ or ►] button and press the [EXIT] button when finished.
WDR-516S Installation Guide
22
Rev 1.0(93/11)
8.2.3. Time Format
(1) Select “Time Format” using the [◄ or ►] or the [▲/▼] buttons and press [ENTER].
(2) Two Time Formats are available; ‘MM/DD/YYYY’ and ‘YYYY/MM/DD’. Select a value using [▲/
▼] buttons, and press the [EXIT] button when finished. (Default value is ‘MM/DD/YYYY’.)
8.2.4. Date
(1) Select “Date” using the [◄ or ►] or the [▲/▼] buttons and press [ENTER].
(2) Select ‘MM’/‘DD’/‘YYYY’ using the [◄ or ►] buttons, and select the value using the [▲/▼]
buttons.
(3) Press the [EXIT] button when finished.
8.2.5. Time
(1) Select “Time” using the [◄ or ►] or the [▲/▼] buttons and press [ENTER].
(2) Select ‘HH’/‘MM’ using the [◄ or ►] buttons, and select the value using the [▲/ ▼] buttons.
(3) Press the [EXIT] button when finished.
8.2.6. Apply Date/Time
Most setting values are applied automatically, when exiting from the related menu page. But “Date”
& “Time” settings are not applied automatically because they may critically affect the file system of
the recorded HDD. To apply Date/Time settings confirm settings with [Apply Date/Time] button.
(1) Select “Apply Date/time” using the [◄ or ►] or the [▲/▼] buttons and press [ENTER]. A warning
message will appear.
(2) Select “OK” using the [◄ or ►] or the [▲/▼] buttons and press [ENTER]. To cancel, press the
[EXIT] button.
WDR-516S Installation Guide
23
Rev 1.0(93/11)
8.3. Setting Recording Condition
Recording conditions under the “Quick Setup” menu tab apply the same values to all analog channels 1~4.
All settings are applied for 24 hours/day regardless of the values set for “Time Schedule” or “Alarm Rec.”
WDR-516S Installation Guide
24
Rev 1.0(93/11)
(1) Press [MENU] button, and select “Quick Setup.”
(2) Move to sub-menu by pressing [ENTER] or the [▼] button.
(3) Select “Recording” using the [▲/▼] buttons and press the [ENTER] button.
8.3.1. Configuration Status
Displays the recording configuration status. When setting up through the “Quick Setup” menu, “Quick
Setup” will be shown. When setting up through “Normal Rec.” or “Alarm Rec.,” “Custom Setup” will be
shown.
<Note>
Only when all the 16 channels' normal recording conditions are set through 'Macro Setup' and
maintained, it is marked as 'Macro Setup'. Otherwise, it will be marked as 'Custom Setup'.
8.3.2. Channel Status
(1) Select “Channel Status” using [▲/▼] buttons and press the [ENTER] button.
(2) Select a value using the [◄ or ►] button. Press the [EXIT] button when finished.
8.3.3. Recording Speed/Quality
(1) Select “Recording Speed/Quality” using [▲/ ▼] buttons and press the [ENTER] button.
(2) Select a value using the [◄ or ►] button. Press the [EXIT] button when finished.
<Note> Recording Speed/Quality means
- Low : Speed=1ips and Quality=Q5
- Std. : Speed=5ips and Quality=Q5
- High : Speed=15ips and Quality=Q5
- Custom : Manually defined by User.
8.3.4. Speed(ips)
When “Recording Speed/Quality” is set as “Custom,” values can be set manually.
(1) Select “Speed” using [▲/▼] buttons and press the [ENTER] button.
(2) Select a value using the [◄ or ►] button. Press the [EXIT] button when finished.
WDR-516S Installation Guide
25
Rev 1.0(93/11)
8.3.5. Quality
When “Recording Speed/Quality” is set as “Custom,” values can be set manually.
(1) Select “Quality” using [▲/▼] buttons and press the [ENTER] button.
(2) Select a value using the [◄ or ►] button. Press the [EXIT] button when finished.
8.3.6. Audio Recording
(1) Select “Audio Recording” using [▲/▼] buttons and press the [ENTER] button.
(2) Select a value using the [◄ or ►] button. Press the [EXIT] button when finished.
8.3.7. Apply
(1) Select “Apply” using [▲/▼] buttons and press the [ENTER] button.
(2) Setting values are applied and the previous menu will be displayed.
WDR-516S Installation Guide
26
Rev 1.0(93/11)
9. Connecting and Configuring Sensor
9.1. Connecting Sensor Input
To connect a sensor to S1, fix the wire to “S1” and “G“.
S1
G
<Note>
Devices connected to the sensor input should have “Dry contact.” The following diagram is of an
electric circuit with approximately 12mA flows.
WDR-516S Installation Guide
27
Rev 1.0(93/11)
9.2. Setting Sensor at OSD menu
After a sensor is connected, it can be activated through the OSD Configuration menu.
Select the sensor number (S1, S2, etc.) and press the [Enter] button to configure. Use the [◄ or ►]
buttons to select “On” or “Off.” Press [EXIT] when finished.
<NOTE>
When activated, the “Pre / Post Alarm” function will cause the WDR-516S to record images at the
specified Speed and Quality for a length of time before and/or after the sensor is triggered.
WDR-516S Installation Guide
28
Rev 1.0(93/11)
10. Connecting & Configuring Relay Out
10.1. Connecting Relay Out
WDR-516S has total four ports of Relay Out.
To connect a device to “R1,” connect the wires to two “R1”s.
R1
R1
<Note>
The rated voltage and current of Relay Out are as follows. Do not exceed the rated values.
24V DC, 1.25A, 30W
Maximum Switching Capacity
125V DC, 0.24A, 30W
125V AC, 0.5A, 62.5VA
WDR-516S Installation Guide
29
Rev 1.0(93/11)
10.2. Configuring Relay Out
Each relay can be synchronized with a sensor input or with motion detection for each of the four time sch
edules (Weekday (Day), Weekday (Night), Weekend (Day), Weekend (Night)). Relays can also be control
led locally by pressing the [SEARCH/RELAY] button followed by the relay number (1-
4). Relays can also be controlled remotely through the “WDR Manager S/W.”
WDR-516S Installation Guide
30
Rev 1.0(93/11)
11. Connecting External Device with Serial Port
11.1. Connecting Text Input Device (ATM / POS / Access Control)
In addition to images, the WDR-516S can record text data received from POS/ATM through the RS232
serial port.
Connect RS232 to 9pin D-sub of WDR-516S, and configure the “Text” sub-menu under the “System” tab.
Set “Serial Setup” under the “System” menu tab to “RS232” and “Device” to “Text.” The baud rate may d
iffer for each device; consult the device manual for more information.
<Note>
Before installing any external device, consult with the local DENTEC distributor. Some external
devices may not be compatible with the WDR-516S.
WDR-516S Installation Guide
31
Rev 1.0(93/11)
12. Connecting & Configuring Serial Ports for Pan/Tilt/Zoom
12.1. Connecting Serial Port
The WDR-516S has most major PTZ protocols already pre-programmed. Makes and models not
supported can still be controlled using the Transparent Protocol. For a list of supported protocols, refer to
the list on the OSD Configuration menu.
12.1.1. Connecting RS232
Fix the wire to 1~3 pins (RX, TX, GND).
12.1.2. Connecting RS485
GND
R- R+
Fix the wire to 4~5 pins and 8 pin (R+, R-,GND).
12.1.3. Connecting RS422
Fix the wire to 4~8 pins (R+, R-, T+, T-, GND).
GN
TXD
RXD
WDR-516S Installation Guide
32
GND
T-
T+
R-
R+
Rev 1.0(93/11)
12.2. Configuring Serial Port
Configure PTZ serial ports and available modes at “System / Serial Setup”.
After completing serial setup, configure base address and port for each channel under the “Camera” menu
tab. When connecting PTZ devices to several cameras, be sure the base address matches the address for
the camera.
WDR-516S Installation Guide
33
Rev 1.0(93/11)
<Note> Wire Handling
Trimming Wire
When connecting a wire to a terminal block, follow the instructions below. Note the different types of
wire that can be used.
Stranded Wire: Peel off the wiring cover
8~10mm and solder it. Wire gage should be
AWG 22 ~ 26.
Solid Wire: Peel off the wiring cover 8~10mm
and solder it. Wire gage should be AWG 20 ~
26.
Inserting & removing wire
To insert the wire, use a screwdriver as
shown in the diagram to the right.
13. Connecting USB Device
USB port can be used to copy up to 1 minute of images to a USB Flash memory disk. When connecting
USB device, do not exceed the rated values of USB device.
USB Spec. Ver 1.1 (Max 12M bps)
Available Device USB Memory Stick,
Output Voltage/Current Max. 200mA per DC 5V / Port
<Note>
The disk should be formatted with FAT32 type.
WDR-516S Installation Guide
34
Rev 1.0(93/11)
If properly connected, the disk is recognized automatically as in the following picture. To copy images,
the process is as follows: Set copy range (up to 1 minute) Æ Select drive Æ Copy (press “Start”).
<Note>
USB Flash products that require a Windows program to operate may not be recognized by the WDR-
516S.
WDR-516S Installation Guide
35
Rev 1.0(93/11)
14. Connecting External Storage
14.1. IEEE1394 Bay
WDR-516S has three IEEE1394 ports for external storage device interface. With them, WDR-516S can
expand storage capacity up to 4TB.
<Note>
Some IEEE1394 Bay may not be recognized by the WDR-516S. Before purchasing, consult the local
DENTEC distributor.
14.2. Connecting IEEE1394 Device
When using FireWire supported external HDD, hard drive bays can be connected to 1 port in the front
panel or 2 ports in the rear panel. The WDR-516S does not supply power to the hard drive bay; therefore
only bays that use external power can be used.
14.3. Available HDD
It is recommended to use the following HDD models with the WDR-516S. If a non-recommended HDD
is used, DENTEC Corp. will not guarantee the warranty.
Manufacturer : MAXTOR
Series Model No. Size Series Model No. Size
6Y060L0 60GB 4R060L0 60GB
DiamondMax
Plus 9
(7200rpm)
<Note>
Buffer for DiamondMax Plus 9’s model “L” is 2MB; for model “P” the buffer is 8MB.
6Y080L(P)0 80GB 4R080L0 80GB
DiamondMax
6Y120L(P)0 120GB 4R120L0 120GB
16
6Y160L(P)0 160GB 4R160L0 160GB
(5400rpm)
6Y200P0 200GB
6Y250P0 250GB
WDR-516S Installation Guide
36
Rev 1.0(93/11)
14.4. Registering & Formatting HDD
“Disk Manager” will automatically run on start-up after installing a HDD.
If “Disk Manager” does not automatically run on start-up, make sure the HDD is properly installed.
(1) Press [ENTER] button at “Select Disk”.
(2) Select new added HDD (indicated as “[F]”) using [▲/▼] button and press [EXIT] button
(3) Select “Action” using [▲/▼] button and press [EXIT] button.
(4) Select “Add” using [◄ or ►] button and press [EXIT] button.
(5) Select “Apply” using [▲/▼] button and press [EXIT] button. The HDD status is changed to “[*]”.
(6) Select “Action” using [▲/▼] button and press [EXIT] button.
(7) Select “Format” using [◄ or ►] button and press [EXIT] button.
WDR-516S Installation Guide
37
Rev 1.0(93/11)
(8) Select “Apply” using [▲/▼] button and press [EXIT] button. The HDD status is changed to “[R]”
after formatting.
(9) Shut down “Disk Manager” by pressing [EXIT] button.
15. Network Monitoring & Managing
WDR-516S can be accessed, controlled, and managed from remote site via Internet/Intranet.
15.1. Connecting Ethernet
1) Turn off WDR-516S’s power switch.
2) Connect WDR-516S to hub with Ethernet cable.
3) Turn on WDR-516S’s power switch.
<Note>
1. Supply power to WDR-516S after connecting Ethernet cable to protect against electrical damage to
WDR-516S.
2. Check cable connection status.
3. Check LED on WDR-516S’s rear panel after supplying power.
WDR-516S Installation Guide
38
Rev 1.0(93/11)
15.2. Configuring WDR-516S’s Network Information
The following description is on based on Ethernet connection. For more detailed information on the
Network Settings Page, please refer to “WDR-516S OSD User’s Guide”.
(1) Press [MENU] button.
(2) Select “System” using the [◄ or ►] buttons and press [ENTER].
(3) Select “Network” using the [▲/▼] buttons and press [ENTER].
(4) Select “IP Addr” using the [▲/▼] buttons and press [ENTER].
(5) Press [EXIT] button after entering IP address in the dialogue box.
(6) Select “Net Mask” using the [▲/▼] buttons and press [ENTER].
(7) Press [EXIT] button after entering Net Mask in the dialogue box.
(8) Select “Gateway” using the [▲/▼] buttons and press [ENTER].
(9) Press [EXIT] button after entering Gateway in the dialogue box.
(10) Select “DNS” using the [▲/ ▼] buttons and press [ENTER].
(11) Press [EXIT] button after entering DNS in the dialogue box.
(12) Press [EXIT] button to exit the page.
WDR-516S Installation Guide
39
Rev 1.0(93/11)
16. Using WDR Manager
16.1. PC System Requirements for running WDR Manager
Minimal Requirements Recommended Requirements
CPU P-Ⅲ 600MHz or above P-Ⅲ 1GHz or above
RAM 128 MB or above 256 MB or above
VGA 16 MB or above 32 MB or above
OS Windows 2000/XP Windows 2000/XP
Resolution 1024 X 768 pixels or above 1024 X 768 pixels or above
Network 100 Base TX Fast Ethernet 100 Base TX Fast Ethernet
16.1.1. Installing WDR Manager
(1) Insert Setup CD-ROM into CD-ROM drive of administrator’s PC
(2) Doubleclick the WDR Manager setup file. Install Shield Wizard will be automatically installed.
(3) Click the “I Agree” button to accept the license agreement
WDR-516S Installation Guide
40
Rev 1.0(93/11)
(4) Select which components to install and press the “Next” button.
(5) Browse and choose a directory if the default directory is not preferred. Click the “Install” button, after
selecting a directory to install.
(6) Click the “Close” button after WDR Manager program is installed successfully
WDR-516S Installation Guide
41
Rev 1.0(93/11)
16.1.2. Uninstalling WDR Manager
(1) Click Windows “Start” Button.
(2) Select and Click ‘Uninstall’ icon to run Uninstall Shield.
(3) WDR Manager program will be automatically deleted.
16.2. Configstation
Click icon on desktop to run “WDR Manager Configstation” program.
WDR-516S Installation Guide
42
Rev 1.0(93/11)
16.3. Monitor
Click the related icon and run the “WDR Manager Monitor” program.
16.4. Playback
Click the related icon and run the “WDR Manager Playback” program.
WDR-516S Installation Guide
43
Rev 1.0(93/11)
APPENDIX
APPENDIX
WDR-516S Installation Guide
44
Rev 1.0(93/11)
Appendix #1 Installing and Replacing internal HDD
Compatible HDD
It is recommended to use the following HDD models with the WDR-516S. If a non-recommended
HDD is used, DENTEC Corp. will not guarantee the warranty.
Manufacturer : MAXTOR
Series Model No. Size Series Model No. Size
6Y060L0 60GB 4R060L0 60GB
DiamondMax
DiamondMax
6Y120L(P)0 120GB 4R120L0 120GB
6Y080L(P)0 80GB 4R080L0 80GB
Plus 9
16
6Y160L(P)0 160GB 4R160L0 160GB
(7200rpm)
(5400rpm)
6Y200P0 200GB
6Y250P0 250GB
<Note>
L series of DiamondMax Plus 9 has 2MB buffer memory, while P model has 8MB
Installing & Replacing
Adding or replacing HDD should follow below process
(1) Turn off the power of WDR-516S.
(2) Check whether the dip switches are set as illustrated below
WDR-516S Installation Guide
45
Rev 1.0(93/11)
CO
<Note>
The dip switch should be set at ‘MASTER’ position for the first installed or built-in HDD.
Additional HDD should be set as ‘SLAVE.’ Identical dip switch setting may cause system conflict
or mal-function.
(3) Remove the 6 screws as illustrated below and pull up the cover from the rear part to open
SCREW
6EA
TOP
VER
(4) Take out power and data cable of HDD from Main PCB ASS’Y. Remove 4 HDD Bracket screws and
take out HDD ASS’Y.
HDD POWER
CABLE
SCREW
MAIN PCB
4EA
ASS’Y
HDD CABLE
WDR-516S Installation Guide
46
Rev 1.0(93/11)
(5) Fix the HDD with provided screws. Connect power and data cables to HDD
MASTER HDD
HDD POWER
CONNECTOR
HDD FIXING
SCREW 4EA
SLAVE HDD
HDD POWER
CONNECTOR
HDD FIXING
SCREW 4EA
Installing single HDD Installing 2 HDDs
<Note> Caution for HDD Management
1. Replacing ‘SLAVE’ HDD of internal 2 HDDs causes permanent data loss in the SLAVE HDD.
2. MASTER HDD has all the index of stored data including ‘SLAVE’ HDD. Corruption on ‘MASTER’
HDD may cause total data loss. Be careful when handling the main HDD.
3. It is strongly recommended that MASTER HDD should be backed up before replacing
(6) Connect HDD power cable to main PCB ASS’Y. Secure the HDD with screws.
HDD POWER
CONNECTOR
MAIN PCB
ASS’Y
ASSEMBLED
HDD
(7) Connect HDD cable’s connector to HDD as in the following picture.
WDR-516S Installation Guide
47
Rev 1.0(93/11)
HDD
CABLE
(8) Assemble the top cover.
Registering & Formatting HDD
“Disk Manager” will automatically run on start-up after installing a HDD. If “Disk Manager” does not
automatically run on start-up, make sure the HDD is properly installed.
(9) Press [ENTER] button at “Select Disk”.
(10) Select new added HDD (indicated as “[F]”) using [▲/▼] button and press [EXIT] button
WDR-516S Installation Guide
48
Rev 1.0(93/11)
(11) Select “Action” using [▲/▼] button and press [EXIT] button.
(12) Select “Add” using [◄ or ►] button and press [EXIT] button.
(13) Select “Apply” using [▲/▼] button and press [EXIT] button. The HDD status is changed to “[*]”.
(14) Select “Action” using [▲/▼] button and press [EXIT] button.
(15) Select “Format” using [◄ or ►] button and press [EXIT] button.
(16) Select “Apply” using [▲/▼] button and press [EXIT] button. The HDD status is changed to “[R]”
after formatting.
(17) Shut down “Disk Manager” by pressing [EXIT] button.
<Note> HDD Type at Disk Manager
1. Available of recording
2. [V] Connected and formatted as WDR-516S’s file system
If using ‘Add used’ command, it will be changed to [R]. There is no need to reformat.
3. [F] Connected but not available file system. After using ‘Add’, need to format for making as [R].
4. [*] Connected and added using the ‘ADD’ command. If formatting, it will be [R].
5. [X] HDD cable is not
<Note> HDD Managing Command
1. Format : Format as WDR-516S’s file system. Not available to PC file system.
2. Add : Add HDD for recording. Need to format.
3. Add Used : Add a HDD that has been used and formatted. There is no need to reformat
4. Remove : Remove current HDD. HDD can be reused without data loss by the ‘Add Used’
command.
5. Confirm Removed : Used when a removed HDD is still listed. ALL DATA WILL BE LOST!
<Note> How to format current HDD?
WDR-516S doesn’t need additional format command. Just do it; ‘Remove’ Æ ‘Add’ Æ ‘Format’.
WDR-516S Installation Guide
49
Rev 1.0(93/11)
Appendix #2 Video Input
Video type / impedance setup switch
It’s possible to set up Impedance of Video input line.
When one Video output is connected to several Input as below, the impedance of one input should be 75
ohm.
REMOTE
CONTROL
Hi-Z
4P
3
2
1
N
ON
OFF
WDR-516S Installation Guide
50
Rev 1.0(93/11)
Appendix #3 Using CD-ROM
Components of CD- ROM disc
Installation Guide : WDR-516S Installation Guide
User’s Guide : WDR-516S User’s Guide
WDR Manager
: WDR Manager User’s Guide
( WDR-516S Remote Management Program)
Preparation
To read manual of CD-ROM disc, Adobe Acrobat 5.0 should be installed in client’s PC.
Reading manual of CD-ROM
Follow the steps to read user’s guide.
1. Insert the supplied CD-ROM into CD-ROM drive of PC.
2. Open the user’s guide, PDF file.
WDR-516S Installation Guide
51
Rev 1.0(93/11)
Appendix #4 Specification
General
CPU 32bit RISC Processor (200MIPS)
Flash Memory 8MB
Main Memory 64MB
OS Embedded LINUX
Video Channel 4 Analog Channel & 12 IP Video Channel (NTSC or PAL)
Storage Device Internal 3.5” IDE HDD 2EA
External 3EA for IEEE1394 Interface
Support Max. 4Tbytes
Intelligent File System Data-loss protection against power failure
Image Compression
Technology Differential Wavelet
Average File Size 1~5KB (Standard Quality)
Image Quality Level 5 Level
Image Compression Rate 20:1~500:1
Recording Speed Max. 120ips in total at NTSC (Analog Ch 60ips + IP Video Ch
60ips)
Network
Browser WDR Manager
Protocol TCP/IP, ARP, ICMP, DHCP, PPPoE
Connector 10/100Mbps Ethernet (RJ-45)
S/W Upgrade Firmware upgrade via Network
Simultaneous Users Monitoring : Max. 5 Users
Playback : Max. 5 Users
Security Password (User or Administrator Authentication)
Watermarking (Against image forging)
WDR-516S Installation Guide
52
Rev 1.0(93/11)
Display
Monitoring Max. 120ips (Analog Video 60ips)
(IP Video 60ips)
Viewer 1ch, 4ch, 9ch, 13ch, 16ch, Auto Sequential
Playback Performance Max. 60ips
Playback Speed 1x, 2x, 4x, 8x, 16x (Forward & Reverse Play)
Function Step-Forward, Step-Reverse
Environment
Operation Temperature 5~45 Cº
Storage Temperature -10~55 Cº
Operation Humidity 30~80%, free of condensation
Storage Humidity 93% below, free of condensation
Data Backup/Expansion/Copy
HDD Expandable Data Backup IEEE1394
Analogue VCR VHS Video output for VCR
Backup Reminder Daily / Weekly / Monthly
Data Copy USB Flash memory disk
Input/Output
Video 1 Monitor output via BNC
1 Video output via BNC
Audio 1 Input : Line-in, 1 Vpp
1 Output : Line-out, 1Vpp
Level : -7~8(16 Step) Recording level
AMP : 20dB amplifier for low level audio
Monitoring : Local and remote
Digital Output 4 Relay outputs (Max DC 30W, AC 62.5VA)
Digital Output Schedule Daily : Day / Night
Weekly : Weekdays / Weekends
Conditions : MD, Sensor inputs
Sensor Input 4 Sensor inputs (Support Dry contact)
WDR-516S Installation Guide
53
Rev 1.0(93/11)
PTZ Control
Serial Port RS232(1), RS485/422(1), RS232(1)
Control Method (Local) Front panel button & IR remote controller
(control IP video channel as well)
Control Method (Remote) On-the-screen PTZ control on PC
Preset Mode 16 points preset per channel
Others
Digital Zoom 2x (Live & PlayBack Mode)
Alarm Trigger Motion Detection or Sensor input
Alarm Data Preservation Alarm triggered Video Data Preservation
Alarm Log Log search
Log monitoring via OSD & Network
Pre/Post Alarm Pre : 1~10 seconds
Post : 1~60 seconds
Schedule Recording Daily : Day / Night
Weekly : Weekdays / Weekends
Conditions : Normal / Event
Text Data Recording POS/ATM transaction information archived along with
corresponding video data
Electricity
Power (Applied Adaptor) DC 12V
Consumption Current Max 4.5A (Internal 2 HDD)
Typical 2.9A (Internal 2 HDD)
Consumption Voltage Max. 54W
Typical 35W
WDR-516S Installation Guide
55
Rev 1.0(93/11)
Mechanical
Dimension (WⅹDⅹH) 350ⅹ298ⅹ66(mm)
Weight 3.5Kg (With one HDD)
RS-232
AUDIO
COMM.
RELAY OUT
SENSOR IN
RRTT4321R
T
++
X
X
RS422/485
RS232
R4R3R2R1
__
VIDEOVIDEO
OUTPUT
INPUT
IN
OUT
CH2
CH1
MON
VCR
CH3
CH4
REMOTE
CONTROL
1
POWER
ETHERNET
10/100
N
ON
IEEE 1394
Hi-Z
1
3
4P
2
OFF
DC12V
2
USB1
USB2
USB IEEE1394
WDR-516S Installation Guide
PWR NET REC
A1
A2 A3
1432
55
PLAY
A4
SEQ
SELECTMULTIZOOM
09
765
8
SEARCH /
RELAY
10+
Network Matrix DVR
MENU
PAUSE
REW
ENTER
STOP
HELP
FFW
WDR- 516S
Rev 1.0(93/11)
Model： WDR-516S
Warranty： Full 1 year as of invoice shipping date
Manufacture ：DENTEC CORP.
Email: tech@dentec.com.tw
Address： 8/F, No. 116 Hou-Kang St. Shih-Lin Dist,
Taipei, Taiwan
http://www.dentec.com.tw
WDR-516S Installation Guide
56
Rev 1.0(93/11)
Loading...