Maxtor 4 Channel Digital Video Recorder User Manual

Page 1
Thank you for purchasing our product.
Please read this User’s Manual before
using the product. Change without Notice
4 Channel Digital Video Recorder
User’ s Manual
1
Page 2
A
Safety Precautions
This label may appear on the bottom of the unit due to space limitations.
CAUTION
RISK OF ELECTRICAL
SHOCK. DO NOT OPEN !
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVI CEABL E PARTS REFER SERVICIN G TO QUALIFIED SERVI CE PERSONN EL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of insulated
dangerous Voltage within the product’s enclosure that may be
sufficient magnitude to constitute risk of electrical shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operation and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE UNITS NOT SPECIFICALLY DESIGNED FOR
ttention: installation should be performed by qualified service
Personnel only in accordance with the National Electrical Code or
applicable local codes.
Power Disconnect. Units with or without ON-OFF switches have
power supplied to the unit whenever the power cord is inserted into
the power source; however, the unit is operational only when the
ON-OFF switch is the ON position. The power cord is the main power
disconnect for all unites.
“CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
Warranty
and Service
manufacturer‘s instruction.”
During the warranty period (one year), we will repair or replace the
DVR free of charge.
Be sure to have the model number, serial number and vendor stick on
hard disk for service representative.
2
Page 3
About this document
Before installing stand alone DVR, be sure to thoroughly review and follow the instructions in this Users
Manual. Pay particular attention to the parts that are marked NOTICE.
Also, when connecting with external application, first turn the power OFF and follow manual
instruction for appropriate installation.
Before reading this document
1. This document is intended for both the administrator and users of stand alone DVR Model.
2. This manual contains information for configuring, managing and using stand alone DVR Model.
3. To prevent fire or electrical shock, do not expose the product to heat or moisture
4. Be sure to read this manual before using stand alone DVR Model.
5. For questions and technical assistance of this product, contact your local dealer.
Strong recommendation on installation of the DVR unit
1. Check electricity at the place you want to install the DVR unit is stable and meets our electricity
requirements.
Unstable electricity will cause malfunction of the unit or give critical damage to the unit.
2. Several chips on the main board of the DVR unit and hard disk drive inside the unit generate heat,
and it must be properly discharged.
Do not put any objects just beside exhaust port(fan) on the left side of the unit and do not close up an
opening (fresh air in-take) on the right side of the unit..
3. Put the DVR unit at well-ventilated place and do not put heat-generating objects on the unit.
When it is installed inside 19 inch mounting rack together with other devices, please check built-in
ventilation fan of the rack is properly running.
3
Page 4
Content
Safety Precautions………………………………………………………………………………………………… 2
About this document………………………………………………………………………………………………. 3
Before reading this document……………………………………………………………………………………. 3
Unite Description of Front Panel………………………………………………………………………………… 5
Unit Description of Rear Panel……………………………………………………………………………………6
Installation………………………………………………………………………………………………………….. 7
Function Setup…………………………………………………………………………………………………….. 15
Login…………………………………………………………………………………………………………. 15
Basic Operation…………………………………………………………………………………………….. 4
USB Data Read and Networking………………………………………………………………………………... 39
Record Time Table: 80 GB HD………………………………………………………………………………….. 49
VGA Description (Optional) ……………………………………………………………………………………… 50
Additional…………………………………………………………………………………………………………….51
4
Page 5
Unit Description of Front Panel
4 split screen
Playback forward / reverse
Function item change shuttle.
1 ~ 4 full screen / password
Sequence / Freezer / Zoom / Water Mark(PTZ mode) / Information
MENU button / PLAY button / REC. record button LOCK key lock button BACKUP data back up button / T-SRH time search playback button ESC function exit button
Value change button
Direction UP / Down,
Record and play stop,
Playback pause / steps.
ENTER / Audio ON or OFF
Direction Left / Right
Playback forward or reverse.
Function LED light display
Remote controller IR
USB. Data backup or firmware update
5
Page 6
Unit Description of Rear Panel
Power cord in 12V/5A, power switcher (ON / OFF)
Camera 1 ~ 4 in and
looping out
Audio channel
input x 1 and output x 1
Main Monitor
RS-485
VGA
Control keyboard connector
75 Ohm ON/OFF (high/low adjust)
VGA output. PC monitor connector.
(Optional)
S-Video (Y/C) monitor
LAN. Network connector
Notice: Reboot DVR after installing any device.
RS-232 connector (ISP. For RD control)
Alarm connector
6
Page 7
Installation
Procedure
1) Camera Connection
Connect the camera to the CAMERA INPUT
on the Rear Panel of the 4 CH DVR.
CH1 CH2 CH3
CH1 CH2 CH3 CH4
CH4
MONITOR
7
Page 8
NOTICE: Sensor input is RECOGNIZED as LOW when alarm signal is on a level with GND, and it is
recognized as HIGH when alarm signal is FLOATING or 5V. Following is internal circuit.
5
Internal Circuit
V
D1
Thus, there is a danger of damage, when the sensor input goes to a Negative level or voltage higher than 5V.
5) Network Connection
DVR connects to LAN
ETHERNET
rks
TERATRAY CONNECTION
To view video image on the computer through internet with DVR view software.
8
Page 9
5) HDD connection
1
How to connect single HDD 2 How to connect 2 HDD
I/O BOARD
MAIN BOARD
Set the drive jumpers as specified by hard disk drive manufacturer.
1
tie
2
3
MASTER
HDD
1
2
3
I/O BOARD
MAIN BOARD
Set the drive jumpers as specified by hard disk drive manuf acturer.
2
1
MASTER
HDD1
3
SLAVE
HDD2
1. Make sure the HDD is MASTER.
2. Make sure the cable connector is
correct.
3. Please check the HDD panel for
Master set up.
1. Make sure the HDD is MASTER and
SLAVE.
2. Make sure the cable connector is
correct.
3. Please check the HDD panel for
Master and Slave set up.
Notice:
-Hard Disk Master and Slave jumper pin must right, otherwise it makes DVR work fault.
Hard Disk testing table:
Brand Model Capacity Notice
Seagate Barracuda 80 GB
IBM DeskStar 80 GB
WD2000 Caviar 200 GB
Hitachi DeskStar 80 GB
Maxtor MaxLineII 300 GB
9
Page 10
Picture
Full screen or split screen display
Press button, to display 4 split screen.
Press numeric buttons to display the desired camera image in full screen.
1.) FREEZE Mode
1. In live mode press (FREEZE) button to freeze image.
2. Press
2.) Zoom Mode(Display Enlargement.)
Go to full screen mode with numeric buttons at live or playback
mode, then press ZOOM button to display screen Enlargement.
Use
3.) Auto Mode
Press (AUTO) button to start screen auto sequencing, and press it again to cancel auto mode.
again to cancel freeze mode.
button to move position.
4.) W.MARK. Water Mark mode.
Water Mark on to check if the data has modify.
5.) INFO (System Information). Auto disappear after 2 minutes if no any button operating.
** SYSTEM INFORMATION **
1.IP ADDR:
2.GATEWAY:
3.NETMASK:
4.NET USER:
5.HDD SIZE:
6.HDD USED:
7.STATUS1
8.STATUS2
9.UPTIME
10.VERSION:
1. Network IP address
2. Network IP gateway
3. Network IP netmask
4. Network user amount
5. Hard disk capacity
6. Hard disk used percentage
7. First hard disk status
8. Video format
9. System running time
10. System version
10
Page 11
6.) BACKUP. Image backup mode.(Image back up must be done on playback mode only.)
Locate the playback point of which you want. Press BACKUP, back up menu shows:
CDRW / USB CDRW USB
BACKUP MENU
CDR WRITE SPEED
START BACKUP TO CDR
FORMAT USB
START BACKUP TO USB
USB:
The BACKUP CAUTION window pop-up. Press ENTER to begin data back up. Capacity of USB device is not
limit.
On playback mode, presses BACKUP: Lower-Right corner of the screen:
** BACKUP CAUTION **
THE ORIGINAL BACKUP FILE
WILL BE KILLED.
PRESS [ENTER] TO BACKUP.
PRESS [BACKUP] TO CANCEL.
BACKUP MENU
CDR WRITE SPEED x1,x2,x3
START BACKUP TO CDR
BACKUP MENU
FORMAT USB
START BACKUP TO USB
xxx K
xxx K (Presently back up progress)
Important:
If DVR cannot detect USB device, please format it to FAT or FAT 32 on PC OS.
When the file is opened from a CF card, only DVR images will appear, but without sounds.
Additional:
During playback, USB device is full or user press BACKUP button screen display a “PAUSE” caption, User
takes out the USB device to computer USB slot then save data to hard disk. After re-insert USB device to
DVR slot, user press BACKUP again. Press ENTER to continue backup or backup button to cancel.
PAUSE
PS: NetViewer software auto copied to USB device when data backup. See the USB Data Read and
** BACKUP CAUTION **
THE ORIGINAL BACKUP FILE
WILL BE KILLED.
PRESS [ENTER] TO BACKUP.
PRESS [BACKUP] TO CANCEL.
Networking pages.
11
Page 12
Compatible USB: Transcend 256 MB, 1 GB / A-DATA, 512MB / USB Flash Drive 128 MB /
Intelligent Stick 256 MB / SOLOMON 128 MB / ISTEC 1GB.
CD-RW:
7.) Key Lock function
xxx K
xxx K (Presently back up progress)
Press BACKUP to stop saving. Or wait for CD is full done.
Data only read in Netviewer.
>On the Live mode, press nly, numeric, freeze, auto, and zoom buttons could work. (lock), O
Press lock key again to enter the login-in window. Enter admin or user password to unlock.
Key lock function only accept password correct log in even re-boot DVR power.
8.) AUDIO function ))))

Notice

Audio playback only on normal( x 1 ) playback.
)))) xxxxxxxxx
ENTER / AUDIO button
Audio playback: AUDIO ,
)))))displays on the Upper-left of screen. At that time, audio
will playback. Press it again to turn it off.
9. NETWORK Playing
ENTER PASSWORD TO TERMINATE
NETWORK PLAYING
PASSWORD : (*****)
1. When the admin do playback mode on AP (Net Viewer), user can terminate it after into password of DVR.
On AP client, admin needs to connect again.
2. When AP on playback mode, DVR is on playback mode also.
12
Page 13
Playback
1. Playback Mode
PL
1) Press button to begin playback. (System playback the images backward)
2. T-SRH button
1) T-SRH: Playback by time search.
Press T-SRH button to active playback function.
1) TIME LIST (Playback image by Time-Search): Recorded images list (by hours)
AY
MAIN PLAY PAGE
1.MASTER TIME LIST
2.SLAVE TIME LIST
Press direction button
UP/DOWN to choose
items.
3.MASTER EVENT LIST
4.SLAVE EVENT LIST
5.GOTO DATE: 2004/12/31
6.GOTO TIME: 12:12
7.GOTO PLAY
Y / M / D H : M (Beginning of recording time) Y / M / D H : M (End of recording time)
Every playback data list displays by an hour.
No page display limit. 10 items display on each page.
Y / M / D H : M Y / M / D H : M
Press direction button UP/DOWN to choose items.
Press values change button to change to previous / next page.
TIME LIST
Notice:
Every playback data list displays by an hour, but if user finds out like:
1. 10:00 ~ 10:12
2. 10:12 ~ 11:00
Reason: 1. Hard disk is full. 2. User change record mode setup.
13
Page 14
2) EVENT LIST (Alarm List): Event source- Video loss / Alarm trigger / Motion / Record
10 items display on each page / Total 5000 items display for 500 pages. When event list is out of compass,
the total items are less then 5000.
NO Y / M / D H : M CH EVENT
>Event happens time and list.
CH: Event Channel Display.
>1 CH ~ 4 CH
+10 : Display pages by 10 units / +100 : Display pages by 100 units / +1000 : Display pages by 1000 units.
- Press direction button left and right to change +10 / +100 / +1000
EVENT LIST +10
NO Y / M / D H : M CH EVENT
Event type.
>Includes Motion / Alarm / V-Loss / Record / Power On / Event Full / Network (Network total users,
include log in and log out.)
>Special time search playback:
Go TO DATE:2002∕12∕12
-Choose year / month / day
>Press direction button Left / Right to choose items, press values change button to change value.
GOTO TIME:12:12
-Choose hour and minute
Press direction button UP/DOWN to choose items.
Press values change button to change page. Press ENTER to start
playback.
>Press direction button Left / Right to choose items, press values change button to change value.
GOTO PLAY
-Press ENTER button to start playback.
Notice: Playback speed change by or shuttle. Speed is x 1, x 2, x 4, x 8, x 4.
14
Page 15
Function Setup
LOGIN
MENU
1) Press
2) Password enter window pop-up:
3) Press numeric (1 ~ 10 )button or remote controller ( 1 ~ 10 )to choose password.
button to enter into menu. You could do the system function setup in MENU.
CHECK PASSWORD MENU
PASSWORD (*****)
Default password (Account-Admin) : 44444
Defau l t pas s w or d (A cc ou n t -U s er ) : 11111
4) Remote controller function buttons are same as DVR panel function buttons.
15
Page 16
Basic Operation
Press MENU button to enter MAIN SETUP PAGE.
MAIN SETUP PAGE
1. HDD INFORMATION
2. DATE-TIME SETUP
3. DISPLAY SETUP
4. CAMERA SETUP
5. BUZZER
6. RELAY SETUP
7. SYSTEM SETUP
8. ADVANCED SETUP
1) Use direction button up/down
2) Press
3) Press sub-menu item with direction button up/down
button to enter into sub-menu function setup.
MENU, ESC: EXIT, ENTER: RUN
button to select setup item.
SETUP
or left/right
And change the value with values change button or turn inner-shuttle.
4) Press ESC to go back to main / sub menu or exit menu.
Notice:
1. ADMIN level can setup all DVR menu functions.
2. USER level cannot setup ADVANCED page of DVR main menu function.
3. Auto disappear after 4 minutes if no any button operating.
button.
16
Page 17
1. HDD INFORMATION
- 2 hard disk information display.
Information display: POSITION SIZE USED BRAND
1. HDD INFORMATION
2. DATE-TIME SETUP
3. DISPLAY SETUP
4. CAMERA SETUP
5. BUZZER
6. RELAY SETUP
7. SYSTEM SETUP
8. ADVANCED SETUP
MENU, ESC: EXIT, ENTER: RUN
MAIN SETUP PAGE
SETUP
POSITION SIZE USED BRAND
MASTER
LAST TIME
SLAVE
LAST TIME
MENU, ESC: EXIT, :PAGE
>POSITON: Master / Slave
>SIZE: Hard Disk capacity. xxGB. Maximum display is 999MB
>USED: 00 ~ 100 %. Hard disk overwrites 100 ~ 199 %.
>BRAND: DVR auto detect hard disk brand.
>LAST TIME: The last record time display.
17
Page 18
2. DATE-TIME SETUP
1. DATE
2. TIME: > Use direction button up/down choose position, values change button to change date and time
1. HDD INFORMATION
2. DATE-TIME SETUP
3. DISPLAY SETUP
4. CAMERA SETUP
5. BUZZER
6. RELAY SETUP
7. SYSTEM SETUP
8. ADVANCED SETUP
MENU, ESC: EXIT, ENTER: RUN
MAIN SETUP PAGE
SETUP
DATE-TIME SETUP PAGE
1. DATE 2000 / 00 / 00
2. TIME
3. FORMAT
3. DISPLAY AT xx LI N E (S )
MENU, ESC:EXIT, :MODIFY
values. Do not need to stop hard disk working (Play or record).
3. FORMAT:
YY/MM/DD, MM/DD/YY, DD/MM/YY, YY/ENG/DD, ENG/DD/YY, DD/ENG/YY, YYYY/MM/DD,
MM/DD/YYYY, DD/MM/YYYY, YYYY/ENG/DD, ENG/DD/YYYY, DD/ENG/YYYY.
Y=Year. M=Month. D=Day. ENG=Month display in English.
4. DISPLAY AT xx LI N E (S )
-Date and Time position on screen xx line(s). 00 ~ 23.
-. Day and time change
Press direction button up/down/left/right to choose items or move date-time position.
Press values change button to change values.
18
Page 19
3. DISPLAY SETUP
1. DATE-TIME: Date and Time caption display mode on or off setup.
>ON / OFF
2. CAMERA TITLE: Camera Title caption display mode on or off setup.
1. HDD INFORMATION
2. DATE-TIME SETUP
3. DISPLAY SETUP
4. CAMERA SETUP
5. BUZZER
6. RELAY SETUP
7. SYSTEM SETUP
8. ADVANCED SETUP
MENU, ESC: EXIT, ENTER: RUN
MAIN SETUP PAGE
SETUP
DISPLAY SETUP PAGE
1. DATE-TIME ON
2. CAMERA TITLE ON
3. PB DATE-TIME
4. PB CAMERA TITLE ON
5. PB DUMMY CAMERA ON
6. DVR STATUS ON
7. BORDER COLOR WHITE
MENU, ESC:EXIT, :MODIFY
ON
>ON / OFF
3. PB DATE-TIME: Play back date and time caption display mode on or off setup.
>ON / OFF
4. PB CAMERA TITLE: Play back camera title caption display mode on or off setup.
>ON / OFF
5. PB DUMMY CAMERA: To clear dummy image if channel input not up to 4.
>ON / OFF
6. DVR STATUS: DVR system, record, playback, audio caption display mode on or off setup.
>ON / OFF
7. BORDER
COLOR: Border color WHITE / DARK / BLACK / GRAY.
Press direction button up/down to choose the desired item.
Press values change button to change values.
19
Page 20
4. CAMERA SETUP
MAIN SETUP PAGE
1. HDD INFORMATION
2. DATE-TIME SETUP
3. DISPLAY SETUP
4. CAMERA SETUP
5. BUZZER
6. RELAY SETUP
7. SYSTEM SETUP
8. ADVANCED SETUP
MENU, ESC: EXIT, ENTER: RUN
SETUP
CAMERA SETUP PAGE
1. COLOR SETUP
2. TITLE SETUP
3. SCREEN POSITION SETUP
4. V-LOSS DISPLAY SETUP
5. VIDEO MASK SETUP
MENU, ESC: EXIT, ENTER: RUN
>>DEFAULT RESET<<
MENU,ESC:EXIT, 71.66068 Tm(EXIT)Tj0 10.02 335.32 1 Tf0.0002 Tc -0.E
Page 21
(2.) TITLE SETUP: Input TITLE of each camera. 9 characters can be input.
CAMERA SETUP
1. COLOR SETUP
2. TITLE SETUP
3. SCREEN POSITION SETUP
4. V-LOSS DISPLAY SETUP
5. VIDEO MASK SETUP
Press direction button up/down/left/right to choose items and position.
CH 01 (01 )
CH 02 (02 )
CH 03 (03 )
CH 04 (04 )
MENU, ESC: EXIT: : MODIFY
TITLE SETUP PAGE
Characters choose:
Space:
Numeric: 0 / 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9
Capital letter: A / B / C / D / E / F / G / H / I / J / K / L / M / N / O / P / Q / R / S / T / U / V / W / X / Y / Z
Press values change button to change values.
21
Page 22
(3.) SCREEN POSITION SETUP
CAMERA SETUP
1. COLOR SETUP
2. TITLE SETUP
3. SCREEN POSITION SETUP
4. V-LOSS DISPLAY SETUP
5. VIDEO MASK SETUP
1.
**** SCREEN POSITION****
UP
LEFT
ENTER : DEFAULT
ESC : QUIT
RIGHT
DOWN
Press direction buttons up/down/left/right to move screen position.
2. Press ENTER button for default.
3. Press ESC button to quit.
22
Page 23
(4.) V-LOSS DISPLAY SETUP
** V-LOSS FUNCTION: ON / OFF
CH 01 : ON / OFF
CH 02 : ON / OFF
CAMERA SETUP
1. COLOR SETUP
2. TITLE SETUP
3. SCREEN POSITION SETUP
4. V-LOSS DISPLAY SETUP
5. VIDEO MASK SETUP
VLOSS SETUP PAGE
**V-LOSS FUNCTION:
CH 01 : ON
CH 02 : ON
CH 03 : ON
CH 04 : ON
MENU, ESC: EXIT: : MODIFY
CH 03 : ON / OFF
CH 04 : ON / OFF
PS. If choose on, X icon displays beside camera title.
Press direction buttons up/down/left/right to choose items.
Press values change button to change values.
23
Page 24
(5.) VIDEO MASK SETUP
**VIDEO MASK FUNCTION: ON / OFF
CH 01 : ON / OFF
CH 02 : ON / OFF
CAMERA SETUP
1. COLOR SETUP
2. TITLE SETUP
3. SCREEN POSITION SETUP
4. V-LOSS DISPLAY SETUP
5. VIDEO MASK SETUP
VIDEO MASK SETUP PAGE
**VIDEO MASK FUNCTION:
CH 01
CH 02
CH 03
CH 04
MENU, ESC: EXIT: : MODIFY
CH 03 : ON / OFF
CH 04 : ON / OFF
MASK means the channel would not display on the live screen, but still can set it on recording.
Press direction buttons up/down/left/right to choose items.
Press values change button to change values.
24
Page 25
5. BUZZER
**BUZZER FUNCTION: All buzzer function
>ON / OFF
1. BUTTON BUZZER?
SETUP
MAIN SETUP PAGE
1. HDD INFORMATION
2. DATE-TIME SETUP
3. DISPLAY SETUP
4. CAMERA SETUP
5. BUZZER SETUP
6. RELAY SETUP
7. SYSTEM SETUP
8. ADVANCED SETUP
MENU, ESC: EXIT, ENTER: RUN
BUZZER SETUP PAGE
**BUZZER FUNCTION ON
BUTTON BUZZER ON
ALARM BUZZER ON
MOTION BUZZER ON
V-LOSS BUZZER ON
HDD-FULL BUZZER ON
CRASH BUZZER ON
MENU, ESC: EXIT: : MODIFY
> ON / OFF
2. ALARM BUZZER?
> ON / OFF
3. MOTION BUZZER?
> ON / OFF
4. VLOSS BUZZER?
> ON / OFF
5. HDD-FULL?
> ON / OFF (Buzzer on if hard disk record only once(Record setupÆ HDD FULLÆSTOP REC.)
6. CRASH?
> ON / OFF (Buzzer on if DVR system or hard disk crash.)
Press direction buttons up/down to BUZZER SETUP items.
Press values change button to change values.
25
Page 26
6. RELAY SETUP
**RELAY FUNCTION: ON
1. HDD INFORMATION
2. DATE-TIME SETUP
3. DISPLAY SETUP
4. CAMERA SETUP
5. BUZZER
6. RELAY SETUP
7. SYSTEM SETUP
8. ADVANCED SETUP
MENU, ESC: EXIT, ENTER: RUN
MAIN SETUP PAGE
SETUP
RELAY SETUP PAGE
**RELAY FUNCTION: ON
1. ALARM RELAY: ON
2. MOTION RELAY: ON
3. V-LOSS RELAY: ON
4. HDD-FULL RELAY: ON
5. CRASH RELAY: ON
1. ALARM RELAY: ON
2. MOTION RELAY: ON
3. VLOSS RELAY: ON
4. HDD FULL RELAY: ON (Relay on if hard disk record only once.)
Record setupÆ HDD FULLÆSTOP REC.
5. CRASH RELAY: ON (Relay on if DVR system or hard disk crash.)
Press direction buttons up/down to each item.
Press values change button to change values.
26
Page 27
7. SYSTEM SETUP
SYSTEM SETUP
1. DWELL INTERVAL:
1. HDD INFORMATION
2. DATE-TIME SETUP
3. DISPLAY SETUP
4. CAMERA SETUP
5. BUZZER
6. RELAY SETUP
7. SYSTEM SETUP
8. ADVANCED SETUP
MENU, ESC: EXIT, ENTER: RUN
- 0 ~ 999SEC. Full channel and call monitor auto sequence time.
MAIN SETUP PAGE
SETUP
SYSTEM SETUP
1. DWELL INTERVAL
2. LANGUAGE
3. VIDEO INPUT
4. RS-485 ID
5. RS-485 PROTOCOL
6. RS-485 BAUD RATE
UPTIME: xx HRS
MENU, ESC: EXIT: : MODIFY
2. LANGUAGE:
- ENGLISH / CHINESE / JAPANESE / FRENCH
- After change language, user needs to exit menu. Language would change next time back to menu.
3. VIDEO INPUT: NTSC / PAL system detection.
- AUTO / NTSC / PAL
- User needs to re power on after change.
4. RS-485 ID:
- 01 ~ 4
5. RS-485 PROTOCOL
- KEYB / LILIN / PELCO-P / PELCO-D / NICECAM / DENTEC-D / DENTEC-P
6. RS-485 BAUD RATE
- 1200 / 2400 / 4800 / 9600
-UPTIME: xx HRS. This means the total system working time after DVR first power on.
RS-485 ID and protocol is the command for system control keyboard. If user has no keyboard to control then does not have to care.
Press direction buttons up/down to choose items.
Press values change button to change values.
27
Page 28
8. ADV ANCED SETUP
1. HDD INFORMATION
2. DATE-TIME SETUP
3. DISPLAY SETUP
4. CAMERA SETUP
5. BUZZER
6. RELAY SETUP
7. SYSTEM SETUP
8. ADV ANCED SETUP
MENU, ESC: EXIT, ENTER: RUN
MAIN SETUP PAGE
SETUP
ADVANCED SETUP PAGE
1. ALARM SETUP
2. MOTION SETUP
3. RECORD SETUP
4. PASSWORD SETUP
5. NETWORK SETUP
6. HDD FORMAT
7. FACTORY DEFAULT
8. SOFTWARE UPDATE
1. Alarm function: ON / OFF. Alarm function on or off depends on alarm device includes in DVR system.
2. Alarm duration: 10 ~ 999. Alarm buzzer and record duration time.
ALARM RELAY SETUP
>ALARM 01 ~ ALARM 04: ON / OFF
Even choose on, but RELAY SETUPÆAlarm relay or relay function off, this function is still closed.
ADVANCED SETUP PAGE
1. ALARM SETUP
2. MOTION SETUP
3. RECORD SETUP
4. PASSWORD SETUP
5. NETWORK SETUP
6. HDD FORMAT
7. FACTORY DEFAULT
8. SOFTWARE UPDATE
ALARM SETUP PAGE
1. ALARM FUNCTION
2. ALARM DURATION
3. ALARM RELAY SETUP
4. ALARM POLARITY SETUP
MENU, ESC: EXIT: : MODIFY
ALARM POLARITY SETUP
>ALARM 01 ~ ALARM 4: N.O. / N.C. / OFF
Press direction buttons up/down to choose items.
Press values change button to change values.
28
Page 29
2. MOTION SETUP
MOTION SETUP
**MOTION FUNCTION (For all channels)
**MOTION DURATION
ADVANCED SETUP PAGE
1. ALARM SETUP
2. MOTION SETUP
3. RECORD SETUP
4. PASSWORD SETUP
5. NETWORK SETUP
6. HDD FORMAT
7. FACTORY DEFAULT
8. SOFTWARE UPDATE
-ON / OFF
-10 ~ 999. Motion buzzer and record duration time.
MOTION SETUP PAGE
**MOTION FUNCTION ON
**MOTION DURATION
**CHANNEL NUMBER
1. SENSITIVITY
2. VELOCITY
3. ACTIVATION
4. RELAY
5. MOTION AREA SETUP
MENU, ESC: EXIT: : MODIFY
**CHANNEL NUMBER
-CH 01 ~ 04
1. SENSITIVITY Adjusts motion Detection Sensitivity.
-1 ~ 32 (low Æhigh)
2. VELOCITY Adjusts motion object slow /fast speed detection
-1 ~ 10 (slow speedÆfast speed)
3. ACTIVATION (For each channel)
-ON / OFF. The function only for channel motion detect active, not for motion record per each.
4. RELAY
-ON / OFF
Even choose on, but RELAY SETUPÆMotion relay or relay function off, this function is still closed.
5. >MOTION AREA SETUP<
Press direction buttons up/down to choose items.
Press values change button to change values.
29
Page 30
> MOTION AREA SETUP <
All area detect with factory default. Press ENTER button to change mode and then increase or reduce.
For example:
Clear lattices
Press value change button to reduce.
Press value change button
Page 31
3. RECORD SETUP
RECORD SETUP
1) HDD FULL: When hard disk is full, DVR next step is kept overwrite record or stop record?
-OVERWRITE / STOP REC
Notice: STOP RECOne hard disk record full, stop record. Two hard disk, both of them record full,
ADVANCED SETUP PAGE
1. ALARM SETUP
2. MOTION SETUP
3. RECORD SETUP
4. PASSWORD SETUP
5. NETWORK SETUP
6. HDD FORMAT
7. FACTORY DEFAULT
8. SOFTWARE UPDATE
RECORD SETUP
1. HDD FULL
2. RECORD SPEED
3. RECORD MODE
4. RECORD AUDIO
5. QUALITY
6. SCHEDULE SETUP
7. CHANNEL SETUP
MENU, ESC: EXIT: : MODIFY
stop record.
Record process OVERWRITE STOP REC
M(99%), S(0%) Æ M(100%), S(0%) To second and record To second and record
M(99%), S(100%) Æ M(100%), S(100%) To second and record To second and record
M(0%), S(99%) Æ M(0%), S(100%) To first and record To first and record
M(100%), S(99%) Æ M(100%), S(100%) To first and record Stop record
Notice:
When hard disk is full, system buzzer on, and then presses ENTER to stop. Next to press REC, over write
message window popup.
"** OVERWRITE CAUTION **"
"THE HDD ARE BOTH FULL,"
"RECORDING WILL DELETE"
"THE OLD IMAGE."
"PRESS [ENTER] TO OVERWRITE."
Press ENTER to continue record.
Over write from the first data area.
Press MENU to exit.
31
Page 32
2) RECORD SPEED: Record FPS setup
-1/30(1/30), 1/15(1/15), 1/10(1/10), 1/5 (1/5), 1/3 (1/3), 1/2 (1/2), 1(1), 2(2), 3(3.13), 5(5), 10 (8.33),
15(12.5), 30(25), 60(50), 120(100). NTSC / (PAL)
3) RECORD MODE: Record mode setup.
-ALWAYS / SCHEDULE / EVENT / EVENT ON SCHEDULE / EVENT + SCHEDULE
4) RECORD AUDIO: Audio record setup
-ON / OFF. (Suggest not fewer than 5 fps.)
5) QUALITY: Record image quality setup
- SUPER / HIGH / FINE / NORMAL / LOW
6) SCHEDULE SETUP
7) CHANNEL SETUP: CH01 ~ CH04 record on or off.
Press direction buttons up/down to choose item.
Press values change button to change values.
Additional:
2. RECORD SPEED. 1/30(1/30), 1/15(1/15), 1/10(1/10), 1/5 (1/5), 1/3 (1/3), 1/2 (1/2), 1(1), 2(2), 3(3.13), 5(5),
10 (8.33), 15(12.5), 30(25), 60(50), 120(100).
- 120 is the maximum fps. Full screen playback with 120 frames per each.
- Split screen playback with 60 frames.
3. RECORD MODE. ALWAYS / SCHEDULE / EVENT / EVENT ON SCHEDULE / EVENT + SCHEDULE.
- Always: 24 hours recording.
- Schedule: Date and time schedule recording mode.
- Event: Alarm / Motion / V-Loss event mode recording. (Whatever which channel event, all channel record.)
- Event on schedule: Event record only on schedule time.
- Event + Schedule: Except event on schedule recording, it would still do record if event happens not on
schedule time.
Notice:
After record mode setup, user needs to press REC button to start. Set on Always mode, DVR do record if user
presses REC. Other record mode would ready on DVR idle status.
4. RECORD AUDIO: ON / OFF.
-Choose on, DVR would do audio recording.
32
Page 33
>SCHEDULE SETUP<
RECORD SETUP
1. HDD FULL
2. RECORD SPEED
3. RECORD MODE
4. RECORD AUDIO
5. QUALITY
6. SCHEDULE SETUP
7. CHANNEL SETUP

SCHEDULE SETUP

CURSOR STEP 30MIN / 6MIN
SUN
MON
Factory default is everyday all schedules time on
recording.
Press direction buttons up/down to
SCHEDULE items.
Press values change button to change values.
TUE
WED
THU
FRI
SAT
Press direction buttons up/down/left/right to see
date and time difference.
Press values change left/right button to change 30MIN or 6 MIN
++ / - - : Increase / Reduce. Every day record with factory default.
On , use up/down button to choose date, press button to change on
+ + or - -. After, use direction left / right button to start increase or reduce time area.
Mode function button
+ + increase
- - reduce
33
Page 34
SCHEDULE SETUP
CURSOR STEP
30MIN
SUN
00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00
00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30
MON
00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00
00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30
TUE
00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00
00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30
WED
00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00
00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30
THU
00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00
00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30
FRI
00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00
00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30
SAT
00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00
00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30
For example:
TUE ~ SAT, all day schedule time recording, but SUN 07:00 ~ 22:00 and MON 01:30 ~ 11:30
do schedule recording. User can press ENTER to see the schedule time area difference.
34
Page 35
7) RECORD CHANNEL SETUP PAGE
CH 01 : ON / OFF
CH 02 : ON / OFF
CH 03 : ON / OFF
CH 04 : ON / OFF
RECORD SETUP
1. HDD FULL
2. RECORD SPEED
3. RECORD MODE
4. RECORD AUDIO
5. QUALITY
6. SCHEDULE SETUP
7. CHANNEL SETUP
RECORD CHANNEL SETUP PAGE
CH 01
CH 02
CH 03
CH 04
: MODIFY
MENU, ESC: EXIT:
PS. Choose off if no video input channel or which channel would not do record.
According to channel record, record time would different.
Press direction buttons up/down to choose item.
Press values change button to change values.
35
Page 36
4. PASSWORD SETUP
1) LEVEL (Log In level ID type setup)
>NONE / ADMIN / USER
-ADMIN
-USER
ADVANCED SETUP PAGE
1. ALARM SETUP
2. MOTION SETUP
3. RECORD SETUP
4. PASSWORD SETUP
5. NETWORK SETUP
6. HDD FORMAT
7. FACTORY DEFAULT
8. SOFTWARE UPDATE
PASSWORD SETUP PAGE
1. LEVEL:( )
2. ADMIN:( )
3. USER :( )
Press direction buttons up/down/left/right to
Choose items position.
Press values change button to change values.
-NONE, user does not need to insert password before enter in MENU.
2) ADMIN password
>44444 (Factory Default)
3) USER password >11111 (Factory Default)
Notice:
1. ADMIN level can setup all DVR menu functions.
Press direction buttons up/down/left/right to choose items position.
Press numeric (1 ~ 10 )button or remote controller ( 1 ~ 10 )to choose
Notice:
Password always 5 character input, cannot < 5 characters
2. USER level cannot setup ADVANCED page of DVR main menu function.
3. Auto disappear after 4 minutes if no any manual operate.
36
Page 37
5. NETWORK SETUP
1. SPEED : >512K / 512K / 256K / 128K / 64K
> Upload speed. Choose the close speed by applied.
2. DVR NAME: [ x 15 space ]
3. NET TYPE: STATIC / DHCP / PPPOE / OFF
4. STATIC IP SETUP
5. PPPOE ID SETUP
6. DNS/DDNS SETUP
ADVANCED SETUP PAGE
1. ALARM SETUP
2. MOTION SETUP
3. RECORD SETUP
4. PASSWORD SETUP
5. NETWORK SETUP
6. HDD FORMAT
7. FACTORY DEFAULT
8. SOFTWARE UPDATE
TCP-IP SETUP PAGE
1. SPEED:>512K
2. DVR NAME:[dvr16]
3. NET TYPE: OFF
4. STATIC IP SETUP
5. PPPOE ID SETUP
6. DNS/DDNS SETUP
7. SERVER PORT SETUP
MAC ADDR: xx.xx.xx.xx.xx.xx
Press direction buttons up/down/left/right to
TCP-IP items position.
7. SERVER PORT SETUP
-MAC ADDR
XX.XX.XX. Machine number, user cannot change.
2. DVR NAME: see DDNS apply.
3. NET TYPE:
> choose network connecting type as user.
4. STATIC IP SETUP:
> Depends on LAN or WAN. Input value witch get from network technician or ISP company.
> Advice user apply network speed Upload 512K / Download 512K, to avoid image data too big influence the
remote quality. The network traffic jam always make data transfer slow, it is normal.
STATIC IP SETUP
1. IP ADDR: 192.168.192.250
2. GATEWAY: 192.168.192.254
3. NETMASK: 255.255.255.000
4. INTERNAL MAPPING: OFF
Internal Mapping:
LAN IP corresponding
Press values change button to change values.
37
Page 38
5. PPPOE ID SETUP
If users apply the dynamic IP from ISP, then should input ID and password that from ISP information list. And then go to set DNS/DDNS SETUP For example: Address name is
123456@hinet.net.tw
Password is 654321
PPPOE ID SETUP
1. LOGIN ID: [ x 20 space]
2. :[ x 20 space]
3. PASSWORD: [ x 20 space]
4. CLEAR PPPOE SETUP 4. CLEAR PPPOE SETUP
PPPOE ID SETUP
1. LOGIN ID: [ 123456@hinet.net.tw]
2. :[ ]
3. PASSWORD: [ 654321]
Or
Notice:
1. Please “CLEAR PPPOE SETUP”
if data is changed.
2. PASSWORD shows “*” icon.
PPPOE ID SETUP
1. LOGIN ID: [ 123456 ]
2. :[ @hinet.net.tw]
3. PASSWORD: [ 654321]
4. CLEAR PPPOE SETUP
7. SERVER PORT SETUP
SERVER PORT SETUP
1. W.W.W: 0080
2. VIDEO : 0021
SERVER PORT SETUP
1. W.W.W: 0080
For IE. (feature)
2. VIDEO : 0021
For AP(Net Viewer)
38
Page 39
6. DNS/DDNS SETUP
Whatever user apply a free or pay DDNS, user needs to input every thing below. DDNS apply: User can get a free hostname or pay from website below.
http://www.3322.net/ (China)
1.
2. http://www.changeip.org/
3. http://www.dyndns.com/
4. http://www.no-ip.com/
5. http://www.dhs.org/
6. http://www.dtdns.com/index.cfm?fuseaction=info.hosts
For example: Go to:
http://www.dtdns.com/index.cfm?fuseaction=info.hosts
Click sign up to create an account.
39
Page 40
Fill your information to sign up paper.
After, go to email account to get activate ID and code.
40
Click here to active
Page 41
Fill ID and code.
Click hostnames
41
Page 42
Type Hostname and choose a domain name, and then click Add Hostname. EX: Hostname = Myhostname, Domain = 4irc.com
After click Add Hostname>>
42
Page 43
Data confirm done, then you can go to DVR advanced setupÆ Network setup now.
Advanced setup Æ TCP-IP SETUP
TCP-IP SETUP PAGE
1. SPEED:>512K
2. DVR NAME:[dvr16]
3. NET TYPE: OFF
4. STATIC IP SETUP
5. PPPOE ID SETUP
6. DNS/DDNS SETUP
7. SERVER PORT SETUP
MAC ADDR: xx.xx.xx.xx.xx.xx
TCP-IP SETUP PAGE
1. SPEED:>512K
2. DVR NAME:[Myhostname ]
3. NET TYPE: OFF
4. STATIC IP SETUP
5. PPPOE ID SETUP
6. DNS/DDNS SETUP
7. SERVER PORT SETUP
MAC ADDR: xx.xx.xx.xx.xx.xx
DTDNS hostname
43
Page 44
6. DNS/DDNS SETUP
DNS/DDNS SETUP
1. D.N.S 1: 000.000.000.000
2. D.N.S 2: 000.000.000.000
3. SERVER : DHS
4. DOMAIN: [ x 20 space]
5. LOGIN ID:[ x 20 space]
6. :[ x 20 space]
7. PASSWORD: [ x 20 space] 15. PASSWORD: [your DTNS long in password ]
8. CLEAR DDNS SETUP
DNS/DDNS SETUP
9. D.N.S 1: 000.000.000.000
10. D.N.S 2: 000.000.000.000
11. SERVER : DTDNS
12. DOMAIN: [ 4irc.com ]
13. LOGIN ID:[ your DTNS long in name ]
14. :[ ]
16. CLEAR DDNS SETUP
Important:
LOGIN ID: This is your DTDNS apply login user name! Not Hostname! PASSWORD: This is your DTDNS apply login password, not Activation Code!
44
Page 45
6. HDD FORMAT
ADVANCED SETUP PAGE
1. ALARM SETUP
2. MOTION SETUP
3. RECORD SETUP
4. PASSWORD SETUP
5. NETWORK SETUP
6. HDD FORMAT
7. FACTORY DEFAULT
8. SOFTWARE UPDATE
Æ HDD FORMAT CAUTION!! :
** HDD FORMAT CAUTION!!**
ALL DATA IN HDD WILL BE
DESTROYED!!
PRESS [ENTER] TO FORMAT.
PRESS [ESC] TO CANCEL.
Press direction buttons up/down to
HDD FORMAT items position.
Press ENTER to format all HDD.
Caution: User can format HDD only when
all HDD stop record or playback.
Press ENTER button to format hard disk.
Press ESC button to cancel hard disk format.
Notice:
New hard disk detect: When DVR power, system would detect new hard disk install. If the hard disk is in
different format, then the message popup. User needs to press ENTER to format, if press MENU, and then
this hard disk would not be detected.
** NEW HDD CAUTION **"
"THE NEW HDD IS DETECTED."
"FORMAT THE NEW HDD??"
"PRESS [ENTER] TO FORMAT."
"PRESS [MENU] TO CANCEL."
MENU
Press FORMAT to format.
Press MENU to exit.
45
Page 46
7. FACTORY DEFAULT
ADVANCED SETUP PAGE
1. ALARM SETUP
2. MOTION SETUP
3. RECORD SETUP
4. PASSWORD SETUP
5. NETWORK SETUP
6. HDD FORMAT
7. FACTORY DEFAULT
8. SOFTWARE UPDATE
Press direction buttons up/down to
FACTORY DEFAULT items position.
Press ENTER to restore.
ALL SETUP VALUE WILL BE CLEAR,
AND RESTORE FACTORY DEFAULT!!
PRESS [ENTER] TO RESTORE.
PRESS [ESC] TO CANCEL.
** CAUTION!! **
8. SOFTWARE UPDATE
ADVANCED SETUP PAGE
1. ALARM SETUP
2. MOTION SETUP
3. RECORD SETUP
4. PASSWORD SETUP
5. NETWORK SETUP
6. HDD FORMAT
7. FACTORY DEFAULT
8. SOFTWARE UPDATE
Press ENTER button to restore.
Press ESC button to cancel.
SOFTWARE UPDATE
UPDATE METHOD:
START UPDATE
UPDATE METHOD: USB / HTTP / UNIX
USB: Copy firmware to USB device, and then plug in DVR USB interface. Choose START UPDATE and then
press ENTER to start. Or save the update version to USB device, DVR system would do data update
automatically. USB ERROR displays if no any USB device plug.
NETWORK: Press START UPDATE to link. 80 Port must open in your network server.
UNIX: For R&D testing.
46
Page 47
USB Data Read and Networking
1. Windows 2000 / XP, select small
2. Resolution 1024 x 768.
3. RAM up to 128 MB, system up to PIII-800.
4. Double click SETUP.EXE of CD, and then start to install.
5. User can go to company server to download AP software.
character display.
6. Browse install path and then click Next.
47
Page 48
7. Advice resolution 1024 x 768. According computer equipment, please choose suitable resolution
8. Select Start Menu Folder, and then click Next.
48
Page 49
9. Click create a desktop icon or not, select DVR type, and then click Next. 4 CH and 16 CH DVR Net viewer is suitable. Only some split screen can not display.
10. Click INSTALL to start install.
49
Page 50
11. Click Launch NetViewer and click Finish to done.
50
Page 51
12. Click Setting.
Name: Name the IP address position.(Each name and IP saves every different input)
IP Addr: Input DVR IP address.
AVI codec: Different computer equipment; different AVI format.
1 ~ 16 full screen select.
Full / Quad / 9 split / 16 split
6 split / 8 split / 10 split / 13 split
Microsoft Windows Media video 9 is better.
Or Cinepak Codec by Radius(Slow transmission, better quality) /
Microsoft Video 1(Fast transmission, bad quality).
Video: Fullsize, Halfsize: screen size choose.
NTSC, PAL. Frame/Sec: Video system choose. Record frame choose.
Click OK to confirm.
On Live / PlayBack , click DVR to save action pictures, *.DVR file. It needs this software to play.
Browser, Local record path could change. The path user changes is for .DVR save, *JPG file is always
C:\DVR
- Press DVR to start record .DVR file(DVR LED green on.), press again to stop.
51
Page 52
Click DDNS Host Name:
Which is same DVR MENU Æ ADVANCED SETUP Æ NETWORK SETUP Æ DVR NAME:
TCP-IP SETUP PAGE
1. SPEED:>512K
2. DVR NAME:[Myhostname ]
3. NET TYPE: OFF
4. STATIC IP SETUP
5. PPPOE ID SETUP
6. DNS/DDNS SETUP
7. SERVER PORT SETUP
MAC ADDR: xx.xx.xx.xx.xx.xx
Type DVR DDNS host name: Myhostname.4irc.com
CMD Port: command port 21 or 1025 ~ 5999.
It is same as DVR network setup.
DNS/DDNS SETUP
1. D.N.S 1: 000.000.000.000
2. D.N.S 2: 000.000.000.000
3. SERVER : DTDNS
4. DOMAIN: [ 4irc.com ]
5. LOGIN ID:[ your DTNS long in name ]
6. :[ ]
7. PASSWORD: [your DTNS long in password ]
8. CLEAR DDNS SETUP
DDNS host name: Myhostname.4irc.com
52
Page 53
13. Click Login, depends on limits of authority. (ID / password is same as DVR)
Factory ID is user login. Input admin if you are an administer. Must input on little character.
Factory: Password, admin : 44444, user : 11111. Password displays when log in, user just needs to input ID.
User log in, no PlayBack function authority. Total 6 people log in. Admin x 1, user x 5.
Click OK, after about 5 seconds, admin login!! Message popup. And then click Connect to start.
Login OK!! Check ID or
PASSWORD is correct.
Login error!! Check ID or
PASSWORD is correct.
53
Page 54
14. Click Connect, after about 2 ~ 3 seconds to start connect LAN or WAN. Click Disconnect to stop. If the NETWORK is connecting success, the blue light would keep glisten Else, blue is always on light or not display, the connecting is failed.
Click live / PlayBack / BackPlay mode.
Live: DVR live watching.
PlayBack: Change to playback mode. After 2 ~3 seconds to change.
54
Page 55
PLAY: Click RUN around 2 ~ 30 seconds to start play first record. If over 30 seconds, cannot find any file or
network disconnect, Time out message popup. Please try again play or connect again. Click STOP to end
playback.
TIME LIST: Click RUN, time lists popup. On the item, double click date and time to start play, around 2 ~ 30 to
start play first record. If over 30 seconds, cannot find any file or network disconnect, Time out message popup.
Please try again play or connect again. Click STOP to end playback.
TIME SEARCH: Chose date and time, click RUN, around 2 ~ 30 seconds to start play first record. If over 30
seconds, cannot find any file or network disconnect, Time out message popup. Please try again play or
connect again. Click STOP to end playback.
Notice: PLAY / TIME LIST / TIME SEARCH change, needs to stop play first.
55
Page 56
-Master HDD Event Lists:
lave HDD Event Lists:
-S
lick RUN, time lists popup. On the item, double click date and time to start play, around 2 ~ 30 to start play
C
first record. If over 30 seconds, cannot find any file or network disconnect, Time out message popup. Please
try again play or connect again. Click STOP to end playback.
56
Page 57
5. Backup Play:
1
Click Open to choose file path.
-
57
Page 58
lick Play to start backup data play. Click Stop to end. Click Pause to temporary stop playback. Click Resume
C
to restart.
hoose camera, click mouse right button. Camera 1 ~ 4 switches or reset all. Click Save “CamNo xx image . /
C
save image all to save current image. Save path is C:\DVR.
58
Page 59
. AVI transfer: Click Backup Play
4
VI : On live or playback mode, save files to .DVR file. And then OPEN file, press play to start playback.
A
Press AVI button to start record AVI file. Press again to stop.
nly 2 cameras selectable. A warning message appears if user selects over 3 cameras,
O
59
Page 60
Record Time Table: 80GB HD
ecord Quality: Low. KB Range: Lowest: 13, Highest: 20. Average: 17.
R
REC FPS 120 60 30
REC Hour 11 22 45 91 137
REC FPS 5 3 2 1 1/2
REC Hour 274 456 685 1370 2741
REC FPS 1/3 1/5 1/10 1/15 1/30
REC Hour 4112 6853 2 413706 0565 1140
Re y: Normal. KB Range: Low , Highest: 2 ge: 20.
cord Qualit est: 14 5. Avera
REC FPS 120 60 30
REC Hour 9 19 38 77 14
REC FPS 5 3 2 1 1/2
REC Hour 233 388 582 145 2330
REC FPS 1/3 1/5 1/10 1/15 1/30
REC Hour 3495 5825 1 31450 7479 4967
Re y: Fine. K ge: Lowest: 15, Highest: 28. A e: 22.
cord Qualit B Ran verag
REC FPS 120 60 30
REC Hour 8 17 35 70 105
15 10
15 10
15 10
REC FPS 5 3 2 1 1/2
REC Hour 2 353 529 1059 211 118
REC FPS 1/3 1/5 1/10 1/15 1/30
REC Hour 3177 5295 10591 1 3 5890 1787
Rec : High. K ge: Lowest: 17, Highest: 30. : 24.
ord Quality B Ran Average
REC FPS 120 60 30
REC Hour 7 4 32 64 97
REC FPS 5 3 2 1 1/2
REC Hour 194 323 485 970 1941
REC FPS 1/3 1/5 1/10 1/15 1/30
REC Hour 2912 4854 9709 1 2 4563 9127
Rec : Super. KB Range: Lowest: 19, Highest: 45 ge: 32.
ord Quality . Avera
REC FPS 120 60 30
REC Hour 6 12 24 48 72
REC FPS 5 3 2 1 1/2
REC Hour 145 242 364 728 1456
15 10
15 10
REC FPS 1/3 1/5 1/10 1/15 1/30
REC Hour 2184 3640 7281 1 2 0922 1845
Act g time is n live envir t. This table or referencual recordin base o onmen only f e.
60
Page 61
VGA Description (Optional)
ccessories:
A
1. 20 PIN Male
2. VGA PCB bracket X1
3. Screws X4
to Female D-SUB pin cable X 1
. VGA board introduction.
1
Socket
VGA connector
. Resolution switcher table
2
in 4 Resolution Pin 1 Pin 2 Pin 3
P
640X480 60HZ ON ON ON
800X600 60HZ ON ON OFF
1024X768 60HZ ON OFF ON 640X480 75HZ ON OFF OFF 800X600 75HZ OFF ON ON 1024X768 75HZ OFF ON OFF
Resolution and . switcher description
Step. 1 DVR Power on. NTSC / PAL auto detects.
Step. 2 Pin 4 no used
Step. 3 Pin 1 ~ 3 switcher resolution. Do not need to power off DVR.
61
Page 62
Additional
ard Disk x 2 can be installed on DVR base. Both are 2-iron slices immobile type.
H
2 Iron slices are in the accessories box, please tell supplier if slices are not exist
2-iron slices immobile type:
lices immobile type: 4 screws hole on each slice. 2 for DVR base fixed. Another 2 for hard disk fixed.
S
ard disk install.: Locking hard disk screws, then locking DVR base screws to fixed on.
H
62
Page 63
P / T / Z Dome mode.
. ADVNACED SETUP PAGE Æ P.T.Z SETUP
6
P
ADVANCED SETUP PAGE
1. ALARM SETUP
2. MOTION SETUP
3. RECORD SETUP
4. PASSWORD SETUP
5. NETWORK SETUP
6. P.T.Z SETUP
7. HDD FORMAT
8. FACTORY DEFAULT
9. SOFTWARE UPDATE
TZ SETUP PAGE
PTZ SETUP PAGE
CHANNEL NUMBER
1. ID
2. PRO
3. BAUDRATE
4. AUTO TOUR
5. LINE SCAN
6. AUTO FOCU
7. AUTO IRIS
TOCOL
S
CHANNEL NUMBER
1. ID: 01 ~ 4
2. PROTOCO
3. BAUDRATE: 1200 / 2400 / 4800 / 9600
4. AUTO TOUR: ON / OFF
5. LINE SCAN: ON / OFF
6. AUTO FOCUS: ON / OFF
7. AUTO IRIS: ON / OFF
L: PELCO-P / PELCO-D / LILIN / ABC / ELITAR / DENTEC-D / DENTEC-P / OFF
: CH01 ~ CH4
fter PTZ setup done, go back to live mode. Press W.M. button to PTZ mode.
A
Icon displays beside date and time caption. To use direction button left/
to mov
e PTZ Dome. PTZ Dome can not be control on split screen.
right/up/down
S. Because the P / T / Z Dome setup is independent by channel and ID, user does not worry about the
P
different ID / Protocol / Baud Rate would affect DVR controls P / T / Z dome error. Just make sure channel
ID / Protocol / Baud Rate corresponding is correct.
and
63
Page 64
Front Panel Button Comparison:
.M.: To P / T / Z mode
W
LAY / REC = IRIS off / IRIS open
P
= FOCUS near / FOCUS far
ACKUP / T-SRH = ZOOM IN / ZOOM OUT
B
ENU = P / T / Z Dome Menu
M
RE. : To Preset mode. PRESET: 000 glisten on left-up corner. Moves P / T / Z dome to the position user
F
wants.
hen “PRESET: glistening”, press number button.
W
EX: 1 ~ 9. 10 = 1 + 10, 11 = 1 + 1, 12 = 1 + 2, 21 = 2
OOM : After press ZOOM button to save the presets.
Z
FO : Press FRE. button into preset mode. When “PRESET: glistening”, press number button, and then
IN
press INFO to call preset.
UTO : Press FRE. button into preset mode. When “PRESET: glistening”, press number button, and then
A
press AUTO to clear preset.
+ 1, 132 = 1 + 3 + 2.
64
Page 65
IE Networking Software
. This web is for preliminary IE browser.
1
2. User can download the network viewer fr
3. The AP software is already saved to DVR system IC. User needs to do is:
a.) Go to Advanced SetupÆ Network SetupÆSets LAN or WAN IP address o
b.) Open IE browser, and then into your IP on the IE address bar.
c.) If LAN or WAN connects ok, the 4 Channel Digital Video Record
om this web page or view the DVR video image in the future.
er web page displays like under:
f DVR.
65
Loading...