Maxtor 16Channel Stand Alone DVR User Manual

VER1.2

16Channel Stand Alone DVR

Audio, USB Backup available

Installation & Safeguards

INSTALLATION & SAFEGUARDS

All the safety and operating instructions should be read before the unit is operated.

Environment Condition for Installation

- To prevent electric shock or other hazard, do not expose units to rain, moisture, or dust.

- This unit should be located in an area with low humidity and a minimum of dust..

- Place this unit in a well-ventilated place and do not place heat-generating objects on this unit.

- This unit should not be located in an area where it is likely to be subjected to mechanical shocks.

Before You Start

- Ensure the power switch is in the OFF position prior to starting.

- Do not attempt to service this unit yourself as opening or removing covers may expose you to
dangerous voltage or other hazards.

- Installation should be performed by qualified service personnel only.

- This unit should be operated only from the type of power source indicated on the manufacturer’s
label and with the power supply included with the unit.

Notice

Notice

NoticeNotice

- Be aware thoroughly about the power connection before installation of the unit.

- Before initial configuration or operation you must first set the TIME/DATE, followed by

setting the unit to the FACTORY DEFAULT settings, lastly clearing the HDD. Please follow
these steps in order.

- Pull the unit out of record mode prior to cutting power to the unit. Do this by entering the

setup menu, followed by switching the unit off. Powering off the unit while writing to the
disks can cause critical malfunctions. (ex: Recording Error, Playback Error, System Error)

- When you set the record type, you have to set the Record Configuration and also

Schedule Setup. This unit records as per the Record type & Schedule setup.

- The [REC] button on the front panel is for emergency record using highest image quality.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the

user of this equipment that there are dangerous voltages within the enclosure which may be of
sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to presence of
important operating and maintenance(Servicing) instructions in the literature accompanying the
appliance.

1

Contents

Contents

CHAP. 1 Features & Package Contents ---------------------------------------------------------------- 4

1-1. Features ---------------------------------------------------------------- 4

1-2. Package Contents ---------------------------------------------------------------- 5

CHAP. 2 Function of Each Button ---------------------------------------------------------------- 6

2-1. Front ---------------------------------------------------------------- 6

2-2. Rear ---------------------------------------------------------------- 8

CHAP. 3 Installation ---------------------------------------------------------------- 9

3-1. Installation Configuration ---------------------------------------------------------------- 9

3-2. Detailed Installation ---------------------------------------------------------------- 10

1) Rack Mount ---------------------------------------------------------------- 10

2) HDD(Hard Disk Drive) ---------------------------------------------------------------- 10

3) Camera ---------------------------------------------------------------- 11

4) Monitor ---------------------------------------------------------------- 11

5) Power ---------------------------------------------------------------- 11

6) SPOT, Video Printer ---------------------------------------------------------------- 12

7) Other External Device ---------------------------------------------------------------- 12

CHAP. 4 Operation ---------------------------------------------------------------- 13

4-1. System Log-in ---------------------------------------------------------------- 13

4-2. Factory Default ---------------------------------------------------------------- 13

4-3. Display Configuration ---------------------------------------------------------------- 14

4-4. Live View Setup ---------------------------------------------------------------- 14

1) Full / Multiple View ---------------------------------------------------------------- 14

2) View in Sequence ---------------------------------------------------------------- 15

3) PIP View ---------------------------------------------------------------- 15

4) Freeze View ---------------------------------------------------------------- 15

5) Zoom View ---------------------------------------------------------------- 15

4-5. Record ---------------------------------------------------------------- 16

4-6. Playback ---------------------------------------------------------------- 16

4-7. Search ---------------------------------------------------------------- 17

4-8. PTZ Camera Operation ---------------------------------------------------------------- 18

4-9. Data Back-Up ---------------------------------------------------------------- 18

4-10. Audio Operation ---------------------------------------------------------------- 18

2

Contents

CHAP. 5 Set Up ---------------------------------------------------------------- 19

5-1. Entering the Menu ---------------------------------------------------------------- 19

5-2. Display Setup ---------------------------------------------------------------- 20

1) Screen Display ---------------------------------------------------------------- 20

2) Monitor Setup ---------------------------------------------------------------- 20

5-3. Configuration ---------------------------------------------------------------- 21

1) HDD Management ---------------------------------------------------------------- 21

2) TIME/DATE Setup ---------------------------------------------------------------- 23

3) Camera Setup ---------------------------------------------------------------- 23

4) Interval Setup ---------------------------------------------------------------- 25

5) Alarm Setup ---------------------------------------------------------------- 25

6) Event Popup Setup ---------------------------------------------------------------- 25

7) Buzzer Setup ---------------------------------------------------------------- 26

8) Password Setup ---------------------------------------------------------------- 26

9) System Information ---------------------------------------------------------------- 26

5-4. Record Setup ---------------------------------------------------------------- 27

1) Record Configuration ---------------------------------------------------------------- 27

2) Schedule Setup ---------------------------------------------------------------- 28

3) Holiday Setup ---------------------------------------------------------------- 28

5-5. Back-Up (CDR, USB) ---------------------------------------------------------------- 29

5-6. External Device ---------------------------------------------------------------- 30

1) TCP/IP Setup ---------------------------------------------------------------- 30

2) RS-232C Setup ---------------------------------------------------------------- 32

3) Pan Tilt Zoom Setup ---------------------------------------------------------------- 32

4) Spot Monitor Setup ---------------------------------------------------------------- 33

5) Audio Setup ---------------------------------------------------------------- 33

5-7. Factory Default ---------------------------------------------------------------- 34

5-8. Language Setup ---------------------------------------------------------------- 34

CHAP. 6 Network Setup ---------------------------------------------------------------- 35

6-1. DVR Network Configuration ---------------------------------------------------------------- 35

6-2. Remote Viewer Program ---------------------------------------------------------------- 39

6-3. Back-Up CD Player ---------------------------------------------------------------- 44

CHAP.7 DDNS Web Server ---------------------------------------------------------------- 46

CHAP.8 Specification ---------------------------------------------------------------- 52

CHAP.9 Remocon Key Definition ---------------------------------------------------------------- 53

3

CHAP. 1 Features & Package Contents

1-1. Features

Live View

Real time display per camera
Auto Sequence
PIP (Picture in picture)
Event Popup
Digital Zoom
Display Freeze
Simple Playback mode
Simple PTZ camera control

Record

Variable Record resolution (For higher picture quality or higher recording speed)
Efficient Image Quality setup in 5 steps
Schedule Record / Holiday Record
Event Record (Alarm / Motion)
Emergency Record

CHAP. 1 Features & Package

Contents

Network

View Live and Playback images across IP network
Copy images across the network

Playback

Search & Playback by Date/Time, Event and Camera
Outstanding picture quality by JPEG 2000 compression algorithm (No mosaic effect)
Suitable for recording not only images but also text
Various steps in Forward Playback Speed (X1/16, X1/8, X1/4, X1/2, X2, X4, X16, X32, X64)
Various steps in Backward Playback Speed (X1/16, X1/8, X1/4, X1/2, X2, X4, X16, X32, X64)
Easy and convenient search by Jog Shuttle & Remote Controller

Data Back-Up

Simple Back-Up using built-in CD Writer (Back-up CD Player included in the package)
Network Back-Up using Remote Viewer program(Remote Viewer included in the package)
Supports bigger capacity of HDD (300GB or bigger)
USB Device Back-Up available

Others

Multi-Language (English, Spanish, German, French, Italy, Japan, China)
VGA option board supports both TFT LCD monitor and CRT monitor
Lock the system by Password
JOG / SHUTTLE
PAL/NTSC Auto detection
Control the unit by using Remote Controller
Audio recording : IN-4ch, OUT-1ch (mono)

4

1-2. Package Contents

CHAP. 1 Features & Package Contents

1. DVR Main Unit

2. Remote Controller

3. Power Cable

4. Power Adapter 5. User’s Manual

7. Rubber Pad 8. HDD absorber 9. Battery for remote controller 10. Bolts

Package Contents Description

1. DVR Main Unit STAND-ALONE DIGITAL VIDEO RECORDER

2. Remote Controller DVR control

3. Power Cable AC power supply to adapters for 12 V DC power

4. Power Adapter 12 V DC power supply

5. User’s Manual User’s Manual

6. Software CD Remote Viewer Software & Back up CD player

7. Rubber Pad Prevent DVR from slipping. Attach it to the bottom of main unit

6. Software CD

8. HDD absorber Absorbing the mechanical shock of HDD against the case bottom

9. Battery Battery for remote controller

10. Rack mount
bracket / Bolts

Rack mount bracket

For fixing Rack Mount bracket to DVR (6ea)

For fixing DVR with Rack Mount bracket to 19” Rack (4ea)

For fixing Hard Disk Drive into DVR (8ea)

5

CHAP. 2 Function of Each

Button

CHAP. 2 Function of Each Button

Name Function

① LED Lamps Shows status of operation

②-1 USB HOST Back-Up by connecting USB Media to USB HOST

②-2 USB Device Firmware upgrade by connecting PC with latest firmware to USB port

③ IR IR receiver

④ Camera

selection
&
PTZ camera
control

1. Pressing this button will display a full screen image of that camera

2. Control PTZ camera (Each button is assigned for each PTZ command)

• ON : LIGHT ON • SET : SET PRESET

• OFF : LIGHT OFF • CLEAR : CLEAR PRESET

2-1 FRONT

• OPEN : IRIS OPEN • GOTO : GOTO PRESET

• CLOSE: IRIS CLOSE • AUTO : AUTO SCAN

• NEAR : FOCUS NEAR • F1 : USER 1

• FAR : FOCUS FAR • F2 : USER 2

• WIDE : ZOOM IN • F3 : USER 3

• TELE : ZOOM OUT

⑤ Record /

Playback

⑥ SETUP MENU Set up for SYSTEM MENU or Use to exit the menu

REC Emergency Record at continuous, 60ips, SUPER FINE size

STOP

PLAY Playback of recorded data on HDD

SEARCH Search recorded data on HDD

ENTER Selects each menu option

NEXT Move to next step

▲▼◀▶

Stop of Emergency Record and return to Schedule Record
from Emergency Record. Playback stop.

Press MENU button before powering off the unit.

Navigate in the menu

+ - Reduce or increase the option value in the menu

6

Name Function

CHAP. 2 Function of Each Button

⑦ LIVE View

Control

⑧ Jog Shuttle

Control

PTZ On/Off for PAN/TILT/ZOOM control mode

Press this button first to control PTZ camera connected to
DVR unit via RS-485

ZOOM Zooming an image

FRZ Freezing an image

MODE Switch to split display

MODE button changes screen-division from (to) full screen
to (from) 16-split screen.

PIP Display in PIP (Picture in Picture) mode

SEQ Auto camera image sequencing in full screen mode

K.LOCK Lock the key function.

To unlock, press longer time (for several seconds) and then
input the password.

Q. Play

(Quick Play)

Play from image recorded 2 minutes ago in forward
direction. (in case recorded in continuous mode).

AUDIO Select audio channel

J/SHUTTLE Pressing Jog Shuttle button (Ready for use Jog/Shuttle)

: In playback mode, pressing J. SHUTTLE button make

images frozen.

RUN LED on : While you operate Jog or Shuttle

ACTIVE LED on : When J. SHUTTLE button is pressed

⑨ Jog Shuttle Very easy and convenient search : Press J. Shuttle button, and images in

playback pause, and then Jog and Shuttle makes it very easy and convenient
to search, forward or backward, fast and slow, as user want.

⑩ CD Recorder Data Back-up and Firmware Upgrade using built-in CD writer

7

CHAP. 2 Function of Each Button

2-2. REAR

Name Function

1 RS 485 Connection with PTZ Camera or other external device using RS 485

interface

RELAY Output Relay out terminal

SENSOR Input Sensor input terminal

2 VGA Connection to VGA Monitor (CRT type or TFT LCD monitor)

Just in case you purchased DVR with VGA option board fixed on the main
board of DVR, you can connect VGA Monitor to DVR unit.

3 ETHERNET Connection to ETHERNET device

4 RS-232C Connection to external device as PC using RS-232C to control the DVR

5 CAMERA Input Connection with camera

6 LOOP Output Camera loop out

7 MONITOR

Connection with Composite Monitor

Output

8 SPOT Connection with additional composite monitor

9 DC Power DC 12V 6.67A Adaptor

10 POWER

SWITCH

Power ON/OFF switch for adapters
To avoid accidental deletion of HDD data, please make sure to press

MENU button and enter into setup menu before powering off the unit.
This takes the unit out of record mode for safe shutdown.

11 Audio Input Microphone Input (4ch)

Audio Output Speaker Output (1ch)

8

CHAP.3 Installation

3-1. Installation Configuration

CHAP. 3 Installation

9

3-2. Detailed Installation

1) Rack mount

CHAP. 3 Installation

1. Remove 4 bolts on each side cap to
install rack mount.

2. Attach rack mount bracket to DVR.

3. Attach DVR with rack mount bracket to 19” rack.

2) HDD

Connection of HDD Cable

MAIN BOARD

HDD1 HDD2

HDD1 HDD2

I/O BOARD I/O BOARD

CD-RW

)

(

MASTER

HDD fix

x

x

MAIN BOARD

x

x

x

x

x

x

x

x

x

x

1. Connect Main Board and HDD using SATA HDD data cable and HDD power cable.

2. When you use just 1 HDD, install the HDD onto HDD1 location.

3. When you use 2 HDDs, install the first HDD onto HDD1 location and then install the second HDD
onto HDD2 location in order.

4. Stick the HDD absorber (included in package) on the bottom of case and then install the HDD
on top of them by using the bolts (included in package).

5. Screws must be inserted from outside of the case bottom.

10

3) Camera

Connect cameras to the camera input on rear panel of DVR marked CAMERA IN.

4) Monitor

CHAP. 3 Installation

Connect the video output marked MONITOR to Video-In of Main monitor.

5) Power

VIDEO A

IN OUT

VIDEO B

IN OUT

VIDEO C

IN OUT

Connect one DC 12V, 6.67 A Adaptor to the back side of Power Jack for right operation of
2HDDs and CDRW.

Before you turn on the Power switch, be sure all necessary devices such as Power
adaptor, cameras and Monitor are connected properly to DVR!

Notice

To avoid accidental deletion of HDD data, please make sure to press MENU button

before powering off the unit. This takes the unit out of record mode for safe shutdown.

11

6) SPOT, VIDEO PRINTER

Connection with additional composite monitor

7) Other External Device

CHAP. 3 Installation

RS-232C : Control DVR through RS-232C port by using PC.
RS-485 : Control external device like PTZ Camera. (Pin No.1 & No.2 at Terminal Block).
RELAY Output : Relay Output. (Pin No.3 ~No.5 at Terminal Block)
SENSOR Input : SENSOR Input (Alarm connection) – (Pin No.6 ~ No.26 at Terminal Block)
ETHERNET : Connection to LAN, WAN, Internet.
VGA : Connection to a VGA monitor(CRT,TFT LCD) if optional VGA board is fixed

on the main board as shown in the following figure.
Resolution set by manufacturer is 800x600 60 Hz, and user can set resolution
in MONITOR SETUP / VGA SETUP / VGA RESOLUTION.

Audio Input : Microphone Input (IN1~IN4)

Audio Output : Speaker Output (OUT)

12

4-1. System Log-In

1) To enter into the setup menu, press the [MENU] button.

2) Enter password with channel number button
from No.1 to No.10 on the front of the DVR unit.
(Maximum of 8 digits are available)

CHAP. 4 Operation

DVR LOG-IN

ENTER PASSWORD

_ _ _ _ _ _ _ _

3) After inputting the password, press the [ENTER] button.

INPUT YOUR OWN PASSWORD

TO EXIT, PRESS [MENU]

Administrator :
If the password entered matches previously set password, “ LOGIN ADMIN” message appears and
you can enter into SYSTEM SETUP.
If the password entered does not match previously set password, the DVR unit goes back to live
display mode.

Factory default password is blank. For log-in, just press [MENU] button and then [ENTER] button.

-Factory default password

ADMIN : (Blank)
MANAGER : ‘ 1 ’
USER 1~USER8 : ‘ 2 ’ ~ ’ 9 ’

※ We recommend configuring a unique password as per the procedure in

SYSTEM MENU - CONFIGURATION - PASSWORD SETUP.

※ For security reasons, be sure to make note of your own password.

4-2. Factory Default

Before first operation, you must check first if all connected camera images are displayed properly,
and then login to the SYSTEM MENU. And you also need to set Time/Date, Factory Default, and
then clear HDD. Even though it is brand new one. it is to make DVMR system and HDD ready for
proper operation. Starting recording without FACTORY DEFAULT setting and HDD clear will cause
malfunction.

1. FACTORY DEFAULT 2. HDD CLEAR

DISPLAY SETUP
CONFIGURATION
REOCRD SETUP
BACK-UP
EXTERNAL DEVICE
FACTORY DEFAULT
LANGUAGE

Refer to page 34.

DISPLAY SETUP
CONFIGURATION
REOCRD SETUP
BACK-UP
EXTERNAL DEVICE
FACTORY DEFAULT
LANGUAGE

Refer to page 21.

HDD MANAGEMENT
TIME/DATE SETUP
CAMERA SETUP
INTERVAL SETUP
ALARM SETUP
EVENT POPUP SETUP
BUZZER SETUP
PASSWORD SETUP
SYSTEM IMFORMATION

13

4-3. Display Configuration

CHAP 4. Operation

Current Time & Date

PIP

FREEZE

SEQUENCE

ZOOM

AUDIO

ALARM Record

MOTION Record

CONTINUOUS Record

120(100) IPS @ 720x240(720x288)

240(200) IPS @ 360x240(360x288)

480(400) IPS @ 360x120(360x144)

HDD Status
In live mode : Amount of data recorded
In Playback mode : Amount of data played

LIVE Display

Camera Title

ETHERNET status

Connected

Disconnected

Status of DVR system

Emergency Record (Red)
Schedule Record (Green)
Record Stop (White)
Stop
Forward Playback
Backward Playback
Pause
1/16~1/2x forward playback
1/16~1/2x backward playback
2~4x forward playback
2~4x backward playback
16~64x forward playback
16~64x backward playback

Picture Quality

BASIC

NORMAL

ENHANCED

FINE

SUPER FINE

4-4. Live View Setup

1) Full / Multiple View

Switch to multi-screen display by pressing [MODE]. For full image display, just press the channel button
which you want or continue to press [MODE] button until you see full screen.
When you playback images which recorded in 360X240(360X288) resolution, only 4,9,13 & 16 split
screens are available.

Full screen

Multiple screen changes

14

2) View in Sequence

Press [SEQ] button. It automatically displays full screen images in sequence.

CH16

……

CH02

CH01

●●●●

●●●●

●●●●

CHAP. 4 Operation

3) Picture in Picture(PIP View)

When it is in full screen display mode, you can see other camera in a small
window by pressing [PIP].The other camera in small window is rotating in
sequence to next number of camera and you can set the rotating time
interval as per the procedure in SYSTEM MENU-CONFIGURATION­INTERVAL SETUP.

CAM-01

2

4) Freeze View
Full display mode : If you press the [FRZ] button, the FRZ icon will be activated on the

screen and “F” character will be shown beside camera title, and
live image will be frozen.

Split display mode : If you press the [FRZ] button, the FRZ icon will be activated on the

screen. press the channel button which you want to freeze.
To release frozen image, press channel number of frozen image again
and press [FRZ] button to exit FRZ mode.

5) Zoom View

In full screen, press the [ZOOM] button and move the Selection Frame using J.SHUTTLE or Direction
keys to the area which you want to enlarge. And then press the [ENTER] button for 2-times enlarged
picture. To exit Zoom mode, just press [ZOOM] button again.

Horizontal Movement : J.SHUTTLE
Vertical Movement : Hold [UP or DOWN] button and turn J/SHUTTLE

15

CHAP. 4 Operation

4-5. Record

Recording mode set before delivery by manufacturer (Default recording mode) is Schedule Recording.
In this default recording mode, it records 24 hours/day continuously in weekday and on the weekend.
Once you press the [REC] button while you see live view, the record type is changed to Emergency Record mode.

- Emergency Record : at full resolution/in best quality
Record type : CONTINUOUS, SUPER FINE quality,

120 (100) ips at 720X240 (720x288)

- Schedule Record
Record and stop as set (time interval and
record type) in RECORD-SCHEDULE SETUP menu.

- Stop Record
Recording stopped as set in
RECORD-SCHEDULE SETUP menu.

On the screen

- Emergency Record
: Red Record Icon ( ) and Record LED is lit

- Schedule Record
: Green Record Icon ( ) and Record LED is lit

- Record Stop
: White Icon ( ) and Record LED is off

- Motion Record, Alarm Record, Alarm+Motion Record
: Record standby LED blinks
: Record LED is lit

※ While in Emergency Record mode, press [STOP],

[PLAY], [MENU], or [SEARCH] button to exit from
Emergency Recording mode and return to Schedule
Record mode.

※ For details, refer to the SYSTEM MENU – RECORD

SETUP (Page 27)

Emergency Record [RED]

Schedule Record [GREEN]

Stop Record [WHITE]

- This DVR unit does not record in following conditions ;

※ While entered in the Menu.

※ No camera is connected
※ Overwriting is off in the Record Setup menu.

4-6. Playback

On record mode or stop mode, press [PLAY] button to play the recorded data in 1x speed.
For backward playback, press [PLAY] button again.
Use Jog/Shuttle to pause and control playback speed. To stop playback, press the [STOP] button.

Using Jog/Shuttle

press the [J.SHUTTLE] button in playback mode. The [ACTIVE] LED will be lit, and Jog/Shuttle is ready
for use. The [RUN] LED will blink whenever you operate the Jog/Shuttle.
For forward playback, turn the Shuttle right and turn Shuttle left for backward playback.
Turn Jog using your index figure to see picture by picture in forward or backward direction.
Operation of Shuttle is as follows.

1/4 x : 4 times slower than normal playback speed
1/2 x : 2 times slower than normal playback speed

1 x : Normal playback speed
2 x : 2 times faster than normal playback speed

4 x : 4 times faster than normal playback speed
16 x : 16 times faster than normal playback speed
64 x : 64 times faster than normal playback speed

Backward Playback 32x supportable.

If you want to keep the playback speed you selected using Shuttle, just hold the shuttle at that location for a few
seconds, and playback in speed you selected continues until you rotate Shuttle again.

16

CHAP. 4 Operation

4-7. Search

Press [SEARCH] button, and 3 different methods for searching recorded data are available as shown
in following SEARCH window. For selecting searching method, use direction key or Jog/Shuttle.
After selecting each search method, press [ENTER] button for playback. exit, press [MENU] button.

1) SEARCH BAR
Search by percentage of total recorded data. It starts from image corresponding to set % of data
on the search bar.

2) TIME/DATE
Search by time & date. Playback starts from the time & date selected.

3) EVENT LIST

Search by event list (Motion, Alarm, Video Loss).

SEARCH

SEARCH BAR

TIME/DATE

EVENT LIST

SELECT MENU : ▲▼, & [ENTER]

[START] 2006/JUN/15 AM11:34:34

[ END ] 2006/JUN/15 PM02:50:45

SEARCH : [ENTER], EXIT : [MENU]

SEARCH BAR

[TARGET DATE/TIME]

SELECT: JOG, SHUTTLE

SEARCH page SEARCH BAR page

TIME/DATE

[START] 2006/JUN/20 AM04:04:12

[ END ] 2006/JUN/20 PM08:12:23

INPUT TIME/DATE

2006/JUN/07 AM04:04:12

CH EVENT TIME/DATE 001/001

--

--

--

--

--

--

--

----

----

----

----

----

----

----

EVENT LIST

020 %

---- / - -/ --

---- / - -/ --

---- / - -/ --

---- / - -/ --

---- / - -/ --

---- / - -/ --

---- / - -/ --

-- : -- : --

-- : -- : --

-- : -- : --

-- : -- : --

-- : -- : --

-- : -- : --

-- : -- : --

SELECT: ▲▼, PAGE:+-

SEARCH : [ENTER], EXIT : [MENU]

SEARCH : [ENTER] , EXIT : [MENU]

TIME/DATE page EVENT LIST page

4-8. PAN/TILT/ZOOM Camera Operation

Press [PTZ] button first for PTZ control mode. Numeric buttons from 1 to 16 and direction buttons are
assigned for each PTZ command, and user can control PTZ camera connected to DVR unit by
pressing any one of those 20 buttons, one after the other, as needed, and it is just like control by
separate PTZ controller.

17

CHAP. 4 Operation

Button PTZ command Button PTZ command

1/ON LIGHT ON 10/CLEAR PRESET CLEAR

2/OFF LIGHT OFF 11/GOTO PRESET GOTO

3/OPEN IRIS OPEN 12/AUTO AUTO SCAN

4/CLOSE IRIS CLOSE 13/F1 ~ 16/F4 FUNCTION

5/NEAR FOCUS NEAR UP BUTTON TILT UP

6/FAR FOCUS FAR DOWN BUTTON TILT DOWN

7/WIDE ZOOM IN LEFT BUTTON PAN LEFT

8/TELE ZOOM OUT RIGHT BUTTON PAN RIGHT

9/SET PRESET SET

4-9. Data Back-Up

Enter into SYSTEM MENU-BACKUP-CD-R SETUP.

1) Insert empty CD-R media into CD writer and select the start time & date from which you want to back up.

※ The START & END time / date in HDD sub-menu only shows start and end of recording.

This is not selectable and editable.

※ 700MB on CD-R sub-menu represent size of CD-R media inserted.

2) To set start time of back-up and back-up data size, press the [ENTER] button first on [START] or [SIZE]
sub-menu and adjust using [+] or [-] button and move using [LEFT] and [RIGHT] button for next
change. After setting the time & date and back-up data size, press the [ENTER] button again to exit.

※ End of back-up time will be calculated automatically as per start time & date and the back-up

data size you set.

※ User can select the back-up data size (size of back-up data from start of back-up) on [SIZE] item but

END of back-up time is automatically determined by DVR system.

3) Press [ENTER] button on BURN sub-menu. DVR system starts burning CD.

4) When burning is completed, CD-R media will come out automatically. In the next CD back-up, start

time of CD-R shall be the end time of previous CD-back-up, and you can back-up from that for
continuous data back-up. If you need another backup, repeat the above procedure. To stop backup,
press the [MENU] button.

※ During burning CD, it’s impossible to cancel burning process.

5) User can verify the back-up CD on PC with BACK-UP CD PLAYER (Included in Package).

CD-R SETUP

HDD

[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23

CD-R

[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
[ SIZE ] 000MB

BACKUP

EXIT : [MENU]

HDD

[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23

CD-R 700 MB

[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
[ SIZE ] 700 MB - > 700MB

BACKUP

CD-RW BURNING : IMAGE DATA.

EXIT : [MENU]

CD-R SETUP

4-10. Audio Operation

Press [AUDIO] button to select audio channel..Ch1, Ch2, Ch3, Ch4 or silence in due sequence.
※Sound of the selected audio channel comes out in Live display.

Recorded sound comes out in Playback.

18

CHAP. 5 Set Up

5-1. Entering into the Menu

Enter into SYSTEM MENU by pressing [MENU] button.

Button Function

MENU Enter into SYSTEM MENU, Move to previous menu, ESC

ENTER Selection key, Move to sub-menu, change status (ON or OFF)

NEXT Move to next page

UP Move to upper side

DOWN Move down side

LEFT Move to the left

RIGHT Move to the right

MINUS [-] Decrease the option value

CHAP. 5 Set Up

PLUS [+] Increase the option value

Jog Shuttle Jog left turning : Move backward to next image / Decrease value

SCREEN DISPLAY
MONITOR SETUP

HDD MANAGEMENT
TIME/DATE SETUP
CAMERA SETUP
INTERVAL SETUP
ALARM SETUP
EVENT POPUP SETUP
BUZZER SETUP
PASSWORD SETUP
SYSTEM INFORMATION

Jog right turning : Move forward to next image / Increase value

Shuttle left turning : Decrease playback speed / Decrease value
Shuttle right turning : Increase playback speed / Increase value

SYSTEM MENU

DISPLAY SETUP

CONFIGURATION

RECORD SETUP

BACK-UP

EXTERNAL DEVICE

FACTORY DEFAULT

LANGUAGE ENGLISH

SELECT MENU : ▲▼, & [ENTER]

RECORD CONFIGURATION
SCHEDULE SETUP
HOLIDAY SETUP

CD-R SETUP
USB SETUP

TCP/IP SETUP
RS-232C SETUP
PANTILT SETUP
SPOT MONITOR SETUP
AUDIO SETUP

SYSTEM MENU

19

5-2. DISPLAY SETUP

Setting up parameters for monitor and display on screen.
Enter into SYSTEM MENU-DISPLAY SETUP.

DISPLAY SETUP

CHAP. 5 Set Up

SCREEN DISPLAY
MONITOR SETUP

SELECT MENU : ▲▼, & [ENTER]

1) SCREEN DISPLAY

1

3

5

LIVE
PLAYBACK

VGA SETUP
COLOR BAR TEST

2

Setting up the screen display in LIVE mode
and PLAYBACK mode.

Select the sub-menu which you would like to set using

4

direction buttons and then change ON/OFF with
[ENTER] button.

1. TIME/DATE : Display time & date

2. DVR STATUS : Display system setting status

3. ICON DISPLAY : Display function setting status

4. REC/PLAY BAR : Display record / playback status

5. CAMERA TITLE : Display camera title

2) MONITOR SETUP

VGA SETUP : VGA option card enables to connect TFT LCD monitor or CRT type PC monitor to

DVR unit. To connect TFT LCD monitor or CRT type PC monitor to DVR unit, select

−

resolution as follows using [+] or [

] button. After setting the below option, press
[ENTER] button then the DVR unit will set VGA resolution automatically.
VGA option card supports following resolution, and choose best resolution that
match TFT LCD monitor or CRT type PC monitor to be connected to DVR unit.

- 640X480 / 60Hz - 640X480 / 75Hz ※※※※ NOTICE : In the booting process,

X

600 / 60Hz - 800X600 / 75Hz DVR unit with VGA option

- 800

- 1024X768 / 60Hz - 1024X768 / 75Hz card takes some seconds

- 1280X1024 / 60Hz - 1280X1024 / 75Hz more to set parameters.

COLOR BAR TEST : Adjust color tone of monitor.

(Color bar test is Not available for monitor through VGA)

20

5-3. CONFIGURATION

Various parameters for system can be set in CONFIGURATION menu.
Enter into SYSTEM MENU-CONFIGURATION and press the [ENTER] button.

CONFIGURATION

CHAP. 5 Set Up

HDD MANAGEMENT
TIME/DATE SETUP
CAMERA SETUP
INTERVAL SETUP
ALARM SETUP
EVENT POPUP SETUP
BUZZER SETUP
PASSWORD SETUP
SYSTEM INFORMATION

SELECT MENU : ▲▼, & [ENTER]

HDD SETUP
HDD INFORMATION
HDD CHANGE SETUP

CAMERA TITLE

CAMERA SETTING

CAMERA ACTIVE SETUP

MOTION SETUP

1) HDD MANAGEMENT

Enter into SYSTEM MENU-CONFIGURATION-HDD MANAGEMENT and press the [ENTER] button.

(1) HDD SETUP

This page includes information about start and end of recording, location of recorded data, or location
of last playback on HDD. In addition, users can delete all the data on HDD.

HDD SETUP

On the [HDD CLEAR] sub-menu, press the [ENTER]

STATUS HDD DATE/TIME

---------------------------------------------------------------------­BEGIN MASTER 2005/04/08

12:12:05

RECORD MASTER 2005/04/09

15:09:58

PLAY MASTER 2005/04/08

19:44:31

HDD STATUS IN USE
HDD CLEAR IN USE

button to delete all image data on HDD.
The system will ask password for verification.
After you clear all data on HDD, status of HDD CLEAR
changes from IN USE to EMPTY.
※ When you clear HDD, event list is deleted, too.

ENTER PASSWORD : ________

OK

INPUT YOUR OWN PASSWORD.

TO EXIT, PRESS [MENU]

EMPTY

HDD CLEAR [ENTER], EXIT [MENU]

If you selected OVERWRITE in Record Setup, the HDD STATUS presented as OVERWRITE.

(2) HDD INFORMATION

This menu will show the physical information
of HDD in DVR.

[MASTER-1]

MODEL
SPEED
SIZE
START
END

[MASTER-2]

MODEL
SPEED
SIZE
START
END

HDD INFORMATION

Maxtor 6Y080L0

81,964,302,336 BYTES

2005/04/08 12:08:56
2005/04/08 15:07:06

Maxtor 6Y080L0

81,964,302,336 BYTES

2005/04/08 15:08:26
2005/04/08 19:04:53

TO EXIT, PRESS [MENU]

21

PIO-4

PIO-4

CHAP. 5 Set Up

(3) HDD CHANGE SETUP

Without losing data, user can use HDD from other DVRs, and HDD installed current DVR can be used

to other DVRs.

HDD CHANGE SETUP

SAVE DVR INFO
LOAD DVR INFO

SELECT MENU : ▲▼, & [ENTER]

1) SAVE DVR INFO

Once you press ENTER button on "SAVE DVR INFO" , the DVR information will be saved on HDD.
If the DVR information is saved properly, you can see "NOW CHANGE HDDDISK" message on DVR.
Then power off the DVR and change with new HDD.

※ NOTICE : Be sure to write down the DVR information as like NTSC/PAL, MODEL name, Channel,

HDD location(PORT 1, PORT2). When you want to retrieve the HDD(old), you must do based on this
DVR information.

2) LOAD DVR INFO

"LOAD DVR INFO " : it retrieves recorded HDD from other DVR set.

- HDD retrieval procedure

1. Install HDD with new DVR and power on.

2. Press [STOP] button when the DVR is booting.
(Then, User can see “HDD CHANGE MODE-ON“ message.)

3. It retrieves when user executes “LOAD DVR INFO” in Menu.

Please note that if the HDD conditions are changed between backup and retrieval. There are some

possibilities losing DATA. So, please remember the condition during backup.

22

22

2) TIME/DATE SETUP

CHAP. 5 Set Up

Set time and date of DVR system which is very
important for search with time and date of the event.
Time and date set by manufacturer is different from
local time of user, and user must set time and date
exactly in the first operation. Set time & date using
direction buttons and [-][+] button or Jog shuttle

2.Change the date, time and month format for

user’s convenient

3) CAMERA SETUP

CAMERA SETUP

CAMERA TITLE
CAMERA SETUP
CAMERA ACTIVE SETUP
MOTION SETUP

TIME/DATE SETUP

YEAR
MONTH
DAY
HOUR
MINUTE
SECOND

DATE FORMAT
TIME FORMAT
MONTH FORMAT

SELECT : ▲▼, CHANGE VALUE : - +

CAMERA TITLE SETUP

0123456789 .ABCDEFGHIJKLMNOPQ
RSTUVWXYZ ! #-[ ]*+ -,./ :<=>?@◀▶

CAMERA01 CAM -1
CAMERA02 CAM -2
CAMERA03 CAM -3
CAMERA04 CAM -4
CAMERA05 CAM -5
CAMERA06 CAM -6
CAMERA07 CAM -7
CAMERA08 CAM -8

2005 / JUN /11

PM14:06:45

ASIA
12 HOUR
ENGLISH

SELECT MENU : ▲▼, & [ENTER]

[ENTER] SELECT MODE

[▲/▼] select CAMERA

(1) TITLE : Input Title of each camera. Move to channel you want to change using [LEFT] or [RIGHT]

direction button and then change the title using [-] [+] button. When modification is finished,
press the [ENTER] button. To exit to previous menu, press the [MENU] button.

(2) COLOR : Adjust image color

Move to each element using
[UP][DOWN] button and adjust using

-

] [+] button or Jog shuttle.

[

CHANNEL : Select camera

BRIGHTNESS : Adjust image brightness (-32~ 31)

CONTRAST : Adjust color contrast ( -32 ~ 31)

CHANNEL
BRIGHTNESS
CONTRAST
SATURATION
HUE
CAMERA POSITION

CAMERA COLOR SETUP

+0
+0
+0
+0
32

1

SATURATION : Adjust color saturation ( -32 ~ 31)

HUE : Adjust color hue ( -32 ~ 31)

CAMERA POSITION : Adjust camera image
To the center. If value is lower:Left.value is

SELECT : ▲▼, CHANGE VALUE : + -

higher:Right (0~80)

23

CHAP. 5 Set Up

CAMERA ACTIVE SETUP

CH STATUS LIVE REC

---------------------------------------------------------------------------

01
02
03
04
05
06
07
08

ACTIVE
ACTIVE

LOSS
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE

SELECT : ▲▼ ◀▶, & [ENTER]

ON
ON

OFF

ON
ON
ON
ON
ON

ON

ON
OFF
OFF

ON

ON

ON

ON

CHANNEL

SENSITIVITY GRADE

MOTION DISPLAY TYPE

RECORD DURATION

NUMBER OF CELL OT DETECT

MOTION CONFIGURATION

01

01

OFF

05 SEC

02

SELECT ▲▼, CHANGE VALUE : + -

(3) CAMERA ACTIVE SETUP : With direction button, move to option to be changed, and press [ENTER]

button to select [ON/OFF]. If it is set at LIVE [OFF] and REC [ON], DVR
system records, but does not show live image of set channel.

- STATUS : Shows if image from a specific channel is coming for live display and recording. In normal
camera condition, it is ACTIVE, but LOSS is displayed when the cable is disconnected or
camera is not working.

- LIVE : Decides whether to show LIVE screen image or not.

- REC : Decides whether to record relevant channel or not.

(4) MOTION SETUP: You can set sensitive of motion detection in 4 steps, motion detection area and others

in relation to motion recording in this menu.

(4)-1. MOTION CONFIGURATION

- SENSITIVITY GRADE : Adjusts motion detection sensitivity. (LOW, MEDIUM, HIGH, VERY HIGH)

- MOTION DISPLAY TYPE : Showing cells with motion detected differently from cells with no motion .

- RECORD DURATION : Whenever motion is detected and it is set at Motion Recording mode, DVR

system records for RECORD DURATION from time motion is detected.
(1sec. ~ 99 sec.) (Default duration : 5 sec.)

(4)-2. MOTION MASK SETUP: Set motion detection area. Direction button is for moving and [ENTER]

button is for selection, and [MODE] button is for changing mode of MASK SETUP.

- CELL : Move to the location which you want to detect and then press the [ENTER] button.

Highlighted cell area means motion detection area.

- ALL ON : Set all cells as detection area. Use [ENTER] button to set.

- ALL OFF : Set all cells as no-detection area. Use [ENTER] button to set.

- BLOCK ON : Select detection area by block. Use [MODE] button and press [ENTER] button to set ON.

- BLOCK OFF : Select un-detection area by block. Use [MODE] button and press [ENTER] button to set ON.

Highlighted Area

(Motion Detection Area)

Non-highlighted Area

(No Motion Detection Area)

24

4) INTERVAL SETUP

Set the switching time interval for SEQ or PIP
function.(1 sec. ~ 99 sec.)

INTERVAL SETUP

SWICHING INTERVAL

FULL SCREEN

PIP SCREEN

CHAP. 5 Set Up

01 SEC

01 SEC

(1)FULL SCREEN : set the sequencing switch time interval

in live full screen.

EVENT RECORD

EVENT UPDATE TIME 01 SEC

(2)PIP SCREEN : set the sequencing switch time interval

of PIP window.

SELECT ▲▼◀▶, CHANGE VALUE : - +

(3)EVENT UPDATE TIME : Set the minimum time interval of event to be listed in EVENT LIST.

If EVENT UPDATE TIME is set at 20 sec, only following event happened

20 sec or more than 20 sec later previous event shall be listed in EVENT LIST.

5) ALARM SETUP

Set type of alarm sensors connected to DVR unit.
N.O represents Normal Open type and N.C Normal
Close type.

CHANNEL

ALARM INPUT

DURATION

ALARM SETUP

(1) ALARM INPUT : Select type of alarm sensor

connected to DVR unit (N.O or N.C).

Use direction button and [-] [+] button

to set.

DISABLE represents not to use alarm

N.O ................................ NORMAL OPEN

N.C ................................ NORMAL CLOSE

___ .................................. DISABLE

sensor connected to DVR.

CH1

N.O

005

(2) DURATION : Set the duration of alarm when an

alarm is activated. (0 sec. ~ 300 sec.)

6) EVENT POPUP SETUP

When event is activated, the full image will pop up
as user set.

(1)CHANNEL : Choose a channel

(2)POPUP ON/OFF : Set a popup function at ON/OFF

(3)EVENT : Set event mode which ‘popup’ function is

applied to.

*A : ALARM event. M : MOTION event.

(4)DURATION : Set the duration how long the popup

Image is shown.(0 sec. ~ 60 sec.)

※If more than 2 channels pop up at the same time,

the first channel out of them will be shown.
(For e.g. Ch1 and CH3 pop up at the same time,

CH1 will be shown)

SELECT : ▲▼, CHANGE VALUE : - +

EVENT POPUP SETUP

CHANNEL

POPUP ON / OFF

EVENT

DURATION

SELECT : ▲▼, CHANGE VALUE : - +

CH01

ON

AM

0 3

25

6) BUZZER SETUP

Set parameters for buzzer (On or Off).
Use direction button and [ENTER] button.

KEY BEEP : buzz when button is pressed.
VIDEO LOSS : buzz when video signal is lost.
ALARM ACTIVE : buzz when alarm is activated.
MOTION DETECT : buzz when motion is detected.

User can set all buzzers at On/Off at once
by set ALL at ON/OFF.

7) PASSWORD SETUP

Set user ID and password.

-Use [UP] and [DOWN] button to move to option
and [LEFT] and [RIGHT] button to set user ID.

ALL

KEY BEEP

VIDEO LOSS

ALARM ACTIVE

MOTION DETECT

SELECT : ▲▼, & [ENTER]

CHAP. 5 Set Up

BUZZER SETUP

ON

ON

ON

ON

ON

The password must be consist of 1 to 8 digit
number. Just use numbers button from 1 to 10
on the front panel of DVR unit.

-To change password, user must input current
password and then input new password.

USER I D

USER PW

NEW PW

CONFIRM

PASSWORD SETUP

ADMIN

---------------------

---------------------

---------------------

And input again new password to confirm.

- Default value

ADMIN : ‘ ‘ (Blank)
MANAGER : ‘1’

[K1-K10] INPUT PASSWORD

[ENTER] CHANGE PASSWORD

USER 1 : ‘2”

:
:

TO EXIT, PRESS [MENU]

USER 8 : ‘9’

※ Change the user PASSWORD in the first operation is recommended.
※ In case you forgot PASSWORD, contact dealer of DVR to get instruction to enter into menu to

set new PASSWORD.

8) SYSTEM INFORMATION

SYSTEM INFORMATION

DVR system information including firmware
version, hardware version, product ID, etc….

S/W VERSION VER 1.0
H/W VERSION REV-B. / ES518
PRODUCT ID

01S-2039-001008-AR-01

MASTER-1

WDC WD2000JS-00NCB1

MASTER-2

WDC WD2000JS-00NCB1
CD-R
SAMSUNG CD-R/RW SW-256B

26

TO EXIT, PRESS [MENU]

5-4. RECORD SETUP

This is the most important configuration of the DVR.
Enter into SYSTEM MENU-RECORD SETUP
and press the [ENTER] button.

1) RECORD CONFIGURATION

-

Use direction button to move and [

] [+] button to set value.

(1) OVERWRITE : Set overwrite or stop recording when

the HDD is full.

(2) MULTIPLEX

- DUPLEX : Playback & Ethernet

- TRIPLEX : Playback & Recording & Ethernet

※ Note: DUPLEX MODE is recommended to playback

the images at a maximum frame rate.
But, it makes DVR not to record during search.

(3) QUALITY : Set recording picture quality.

Actually it is fixing maximum data size of
image for each picture quality in 5 steps
as follows.

BASIC

-

- NORMAL

- ENHANCED

- FINE

- SUPER FINE:

Default quality set by manufacturer

RECORD SETUP

RECORD CONFIGURATION
SCHEDULE SETUP
HOLIDAY SETUP

SELECT MENU : ▲▼, & [ENTER]

RECORD CONFIGURATION

OVERWRITE

MULTIPLEX

QUALITY

RESOLUTION

RECORD IN ALARM

RECORD IN MOTION

CONTINUOUS RECORD

CHAP. 5 Set Up

ON

TRIPLEX

ENHANCED

120IPS 720*240

1/1X

1/1X

1/1X

In Emergency recording mode, recording quality is

SUPER FINE.

SELECT MENU : ▲▼, CHANGE VALUE : + -

To send more images via IP network and longer recording

time, set QUALITY at NORMAL or ENHANCED and

record at 360x240(360x288).

※ Data size of image in PAL system is a little bigger than NTSC system, but the total recording time

is same as in NTSC system.

(4) RESOLUTION : Set recording resolution.

- 120 ips at 720x240(NTSC) , 100 ips at 720x288(PAL)

- 240 ips at 360x240(NTSC) , 200 ips at 360x288(PAL)

- 480 ips at 360x120(NTSC) , 400 ips at 360x144(PAL)

※ It is not possible to see those images in full screen mode in playback.

Recording in Dual resolution is recommended for higher recoding speed, and also to send
more images via IP network.

(5) RECORD IN ALARM : Set record speed (skip rate) in ALARM record mode.

(6) RECORD IN MOTION : Set record speed (skip rate) in MOTION record mode.

(7) CONTINUOUS RECORD : Set record speed (skip rate) in CONTINUOUS record mode.

Set record speed (skip rate)

- 1/1x, 1/2x, ………. 1/999x record speed

- ex: 1/2x ) R->S->R->S… - ex: 1/3x ) R->S->S->R->S->S->R…

- ex: 1/4x ) R->S->S->S->R->S->S… ( R : RECORD S : SKIP )

- ex : If record resolution is set at 360x240, 1/1x = 240 ips, 1/2x = 120 ips, 1/3x = 80 ips, etc.

27

CHAP. 5 Set Up

2) SCHEDULE SETUP

Unless you selected other recording mode, DVR system records in Schedule Recording mode.
In SCHEDULE REC SETUP, you set type of recording for every time interval of 2 hours in each day of
the week. Schedule Recording set by manufacturer is recording continuously at its full recording
speed, and it means DVR system record continuously at 60 ips in total at 720x240 resolution.
To set Schedule Recording parameters, enter into SYSTEM MENU-RECORD SETUP-SCHEDULE SETUP
and Press the [ENTER] button.

(1) SCHEDULE SETUP

Set recording type for each recording time interval for a day of the week (2 hours interval).

SCHEDULE REC SETUP

SUN

MON

TUE

WED

THU

FRI

00-02

02-04

04-06

-M-

-M -

- M -

AM -

AM -

AM-

- -C

- -C

- -C

- -C-

- - C

- - C

- -C-

- - C

- - C

- -C

- -C

- -C

SAT

- -C

- - C

- - C

Use [MODE] button to select edit type and move to
the time interval of a day of the week you want to change.

−

Press [ENTER] button to select and use [+] or [

] button,
to change the record type. To go next page, use [NEXT]
button.

06-08

08-10

10-12

MODE: CELL BY CELL

-M -

AM-

-- C

-- C

- - C

-- C

- - -

AM-

- -C-

- - C

- - C

- -C

-- -

AM-

- - C

- - C

- - C

- -C

▲▼◀▶ & [NEXT], EDIT:+ -&[MODE]

A:ALARM M:MOTION C:CONTINUES

-- C

※ MODE (Edit type)

- - C

-- C

TIME CELL : Set each time interval of a day of the week
WEEK : Set a day of the week at once
TIME ZONE : Set a time slot at once
ALL : Set page by page at once

1 / 2

CLEAR ALL: Clear page by page

※ Unless user press [REC] button to record at full resolution and in SUPER FINE picture quality,

DVR system records in SCHEDULE Record mode.

※ DEFAULT record mode for each time interval of a day of the week set by manufacturer is

CONTINUOUS recording.

※ Record type :

After power on Schedule record
Exit from menu Schedule record
End of search or playback Schedule record
After pressing [STOP] button Schedule record
After pressing [REC] button Emergency record (Continuous recording in full performance)

[120(100) ips at 720x240(720x288)]

3) HOLIDAY SETUP

HOLIDAY SETUP

Users can set national holiday or holidays on
calendar to record just as setting for Sunday in
SCHEDULE REC SETUP.

Use [MODE] button to select a month and direction
button to move to a day, and press [ENTER] button to
set a holiday. Then color of date shall be changed to
red, as Sunday.

EDIT HOLIDAY : Set as holiday
CLEAR MON DATA : Cancel the holiday set per month
CLEAR ALL DATA : Cancel all holiday set

※ The maximum holidays is 100 days.

28

< APR > 000/100

SUN MON TUE WED THU FRI SAT

01 02

03 04 05 06 07 08 09

10 11 12 13 14 15 16

17 18 19 20 21 22 23

24 25 26 27 28 29 30

MODE : EDIT HOLIDAY
SELECT ▲▼◀▶, EDIT [ENTER]&[MODE]

CHAP. 5 Set Up

5-5. BACK-UP

1) CD-R SETUP

User can back up the recorded data to CD using CD writer installed in DVR.
Refer to [START] and [END] of data on HDD and set copy from time, [START], and size of data
copied, [SIZE], and move to BURN and press [ENTER] button to start copy.

CD-R SETUP

HDD

[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23

CD-R

[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
[ SIZE ] 000MB

BURN

SELECT : SETUP BUTTON, JOG SHUTTLE

HDD

[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23

CD-R 700 MB

[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
[ SIZE ] 700 MB - > 700MB

BURN

CD-RW BURNING : IMAGE DATA.

SELECT : SETUP BUTTON, JOG SHUTTLE

CD-R SETUP

System Status Messages :

- CD-RW DOOR CLOSE. CHECKING CD-R : Blank CD check

- INPUT BLANK CD : CD writer has no blank CD.

- CD-RW DOOR OPEN : Open CD-RW and insert blank CD –R media into CD drive.

- CD-R MEDIA IS DETECTED : Blank CD-R media has been inserted and detected. DVR system will
display size of blank CD-R.

After you set [START] time and [SIZE] in CD-R sub-menu and then select BURN, DVR system starts
copying images to CD and shows following message.

CD-RW BURINING START
CD-RW BURNING : LEAD-IN
CD-RW BURNING : IMAGE DATA
CD-RW BURING : CLOSE TRACK
CD-RW DOOR OPEN

When burning is completed, CD-R media will be ejected automatically.
To copy more images, repeat above process. In the next back-up process, [START] time in
CD-R sub-menu shall be [END] time in previous back-up, and you can copy images in series
to many CDs as many as you want.

※ SIZE Change

+ , - : Change per 10MB unit LEFT , RIGHT : Change per 100MB unit

2) USB SETUP

User can back up the recorded data to USB Media using USB (HOST) port on front panel of DVR.
Refer to [START] and [END] of data on HDD and set start and end time of data to USB Media
( USB Memory Stick ). Select backup file size, and move to BACKUP and press [ENTER] Button
to start copy.

29

CHAP. 5 Set Up

Partition can be selectable by Ch button 1~4.

Status message

System Status Messages
(1) If USB MEMORY STICK is not inserted :

- USB STORAGE IS CHECKING…

- USB STORAGE IS NOT AVAILABLE

- RE-CONNECT THE USB STORAGE

- CONECT THE OTHER USB STORAGE

(2) When USB MEMORY STICK is recognized

- USB STORAGE IS CHECKING …

- THERE IS A FREE SPACE ON STORAGE

- USB STORAGE IS AVAILABLE

(3) During Back-Up

- CHANGE WRITE PROTECT MODE (Only WRITE PROTECT is caught, it can be seen)

- START WRITING IN USB STORAGE

- FINISH WRITING IN USB STORAGE

(4) Error Message

- THERE IS A PROBLEM ON USB PORT (If USB PORT fails to work properly)

- USB STORAGE IS FULL (When USB is full)

- FILE SYSTEM IS NOT SUPPORTED (If File System is not supported)

- SIZE IS LARGER THAN FREE SIZE (If back-up size is larger than free space)

※ Back-Up procedure is the same as CDR Back-Up.
※ If Back-Up size is larger than 2GB, it creates several files. (It saves by 2GB).

USB SETUP

HDD

[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23

USB MEDIA

[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
[ SIZE ] 00000MB

BACKUP

USB STORAGE IS CHECKING…

EXIT : [MENU]

USB SETUP

HDD

[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23

USB MEDIA 118M , 28M , P:1

[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
[ SIZE ] 28 MB - > 28MB

BACKUP

START WRITING IN USB STORAGE

EXIT : [MENU]

SIZE , FREE SPACE, PARTITION

5-6. EXTERNAL DEVICE

Set parameters of external devices connected to DVR, like Ethernet, PTZ camera, RS-232C, etc.
Use direction button to move to sub-menu and Press [ENTER] button to set.

1) TCP/IP SETUP

TCP/IP function enables user to see live pictures and
recorded pictures via the internet.

(1) IP CONFIG SETUP :

Show the network information assigned to the DVR

unit. If the DHCP setup status is AUTOMATIC, user

MAC ADDRESS

IP ADDRESS

IP PORT

GATEWAY

IP CONFIG SETUP

can set the IP port only and if the DHCP setup status
is MANUAL, user must set all parameters.

SUBNET MASK

For detail procedure of Remote viewer program
installation, refer to CHAP. 6 Software

DHCP SETUP

program.(Remote viewer software).

SELECT MENU : ▲▼, & [ENTER]

30

_ _ _ _ _ _ _ _ _ _ _

00-0A-A2-00-00-00

_ _ _ _ _ _ _ _ _ _ _

192.168.001.160

_ _ _ _ _ _ _ _ _ _ _

50000

_ _ _ _ _ _ _ _ _ _ _

192.168.001.001

_ _ _ _ _ _ _ _ _ _ _

255.255.255.000

AUTOMATIC

(2) DDNS SETUP :

- DDNS ON/OFF : Select if DDNS Function use

CHAP. 5 Set Up

DDNS SETUP

- DDNS SERVERS : IP Address of DDNS SERVER.

- INTERVAL : Registered time period to DDNS SERVER.
Per D(Day) H(Hour) M(Minute)

- REGISTER : Once press [ENTER],
It automatically registered.

- DDNS STATUS : present current status by
"REGISTER OK“
"REGISTER ERROR", "NOT REGISTER"

- IP ADDRESS : IP of last registered DVR

- IP PORT : Port of last registered DVR

- REMAIN TIME : Remain time to next registration

- LAST REG... DATA : Last registered time

(3) CONNECTION SETUP :

- TIME OUT :
Adjust TIMEOUT value properly to
successfully access to DVMR unit via Internet
line. If data transmission speed is high enough,
leave TIMEOUT value as set by manufacturer
(200 msec), and increase it if data ansmission
via Internet line is relatively slow. Execute
tracert (Tracing Route) in your PC for IP
assigned to DVMR unit, and you can figure
out how much TIMEOUT value increased.

- RETRY COUNT :

Set the retry number of times for network
connection.

DDNS ON/OFF OFF
DDNS SERVER 211.062.253.087
INTERVAL D-00 H-00 M-20
REGISTER

-------------------------------------------------------------------------­DDNS STATUS
IP ADDRESS ---.---.---.---.--­IP PORT ----­REMAIN TIME D-00 H-00 M-00
LAST REGISTERATION DATE
>

SELECT MENU : ▲▼, & [ENTER]

CONNECTION SETUP

TIMEOUT 200 MSEC

RETRY COUNT 08

SELECT MENU : ▲▼, & [ENTER]

(4) DHCP SETUP :

- DHCP MODE : If user selects AUTOMATIC,
IP automatically assigned.

If user selects MANUAL, in IP CONFIG SETUP
User selects it manually.

- DETECT IP : It only appears for AUTOMATIC.
Once press [ENTER], it automatically starts IP
Assignment.

31

DHCP SETUP

DHCP MODE

DNS SERVER

IP ADDRESS

SUBNET MASK

GATEWAY

SELECT : ▲▼, CHANGE VALUE : + -

AUTOMATAIC

168.126.063.001

192.168.001.086

255.255.255.000

192.168.001.001

(5) EVENT SERVER SETUP :

IP ADDRESS : IP Address of PC that executes
EVENT SERVER PROGRAM.
IP PORT : PORT of PC that executes
EVENT SERVER PROGRAM
EVENT SERVER TYPE :
It is the way to transmit data to SERVER
By "OFF", "EVENT", "MINUTE“,
In case Event happens from DVR.

"EVENT“: It transmits by the number of EVENT.
"MINUTE“: It transmits each scheduled time.

CHAP. 5 Set Up

EVENT SERVER SETUP

IP ADDRESS 192.168.001.072
IP PORT 09988
EVENT SERVER TYPE OFF
INTERVAL --­EVENT GMT TYPE GMT+00:00

INTERVAL: If EVENT SERVER TYPE is "EVENT"

SELECT : ▲▼, CHANGE VALUE : + -

User can select from 1~512.
If EVENT SERVER TYPE is "MINUTE“, User can select from 1 ~ 60 mins.

EVENT GMT TYPE : User can set currently installed location(DVR) of GMT.

2) RS-232C SETUP

User can control the DVR via RS-232C port.
Connect DVR to PC via RS-232C port and control
DVR using keyboard of PC.
This function is mainly for programmer who

SPEED

LENGTH

STOP BIT

PARITY

RS-232C SETUP

wants to control DVR as part of many devices
connected to PC system, as in SI project.

SELECT : ▲▼, CHANGE VALUE : + -

3) PANTILT SETUP

It is to set parameters for PTZ camera connected to DVR unit. DVR unit already includes all
protocols of well-known PTZ cameras like PELCO D type PTZ camera, and user just select MODEL
and set other parameters to control this PTZ cameras, using operation buttons on the front panel of
DVR.

115200

8

1

NONE

PANTILT SETUP

CHANNEL

MODEL
PTZ ID

COMMAND SETTING  PTZ camera set

SPEED SETTING  PTZ speed set

SELECT : ▲▼, & [ENTER]

BAUDRATE
CMD DELAY

COMMAND

LENGTH
CODE

SELECT : ▲▼, CHANGE VALUE : + -

(1) CHANNEL : Select channel
(2) MODEL : Select camera model (protocol type) per each channel
(3) PTZ ID : Select ID
(4) BAUDRATE : Select data transmission speed
(5) CMD DELAY : Select command delay time

32

COMMAND SETTING

01
PELCO-D
000
2400 BPS
1 MSEC

PAN/TILT STOP
07
FF 00 00 00
00 00 00 00

4) SPOT MONITOR SETUP

CHAP. 5 Set Up

SPOT MONITOR SETUP

SPOT MONITOR SETUP

SPOT MONITOR SETUPSPOT MONITOR SETUP

(1) SWITCHING INTERVAL

Channel switching time (01 sec. ~ 99 sec.)

SWITCH INTERVAL 03 SEC
ALARM POP UP ON
MOTION POP UP ON
EVENT POP UP DURATION 01 SEC

(2) ALARM POP-UP

When ALARM is detected, the image of channel
connected with Alarm sensor pops up.
Set ALARM detection pop-up (ON/OFF)

(3) MOTION POP-UP

SELECT: ▲▼, CHANGE VALUE : + -

※

EVENT POP-UP DURATION

Set MOTION detection pop-up (ON/OFF)

Set EVENT POP-UP DURATION

If events (MOTION or ALARM) happen on several channel at the same time, channel No. 1 has the
first priority to pop up. For example, if events happen on channel No. 1, channel No. 2, and channel
No. 4 at the same time, channel No. 1 pops up. If the motion disappears on channel No. 1, then channel

No. 2 pops up for the duration that you set. However, even though motion happens on channel No. 1

again within the duration, channel No. 2 still displays. If motion on channel No.1 keeps on going even after

the duration, channel No. 1 pops up again.

5) AUDIO SETUP

Use direction button to move to channel and Press [ENTER] button to set (ON/ OFF).

AUDIO SETUP

AUDIO SETUP

AUDIO SETUPAUDIO SETUP

1) REC

CH REC PLAY

01 ON ON
02 ON ON
03 ON ON
04 ON ON

(1) ON : Record images with AUDIO

(2) OFF : Record images without AUDIO

2) PLAY

(1) ON : Recorded sound comes out during

playback

(2) OFF : Recorded images only play back

SELECT: ▲▼◀▶, & [ENTER]

33

CHAP. 5 Set Up

5-7. FACTORY DEFAULT

Set the all system parameters as manufacturer first
set before delivery. It is a kind of system
initialization, and manufacturer recommends to do it
when you add new HDD or other changes in
system to make all system ready for normal
operation.
Use direction button to move and Press [ENTER]
button to change parameters. After move to RUN,
Press [ENTER] button for actual Factory Default
setting.

5-8. LANGUAGE SETUP

The menu can be displayed in a number of languages.
Press [ENTER] button to select your language.

SYSTEM MENU

DISPLAY SETUP

FACTORY DEFAULT

ALL
SCREEN DISPLAY
CAMERA SETTING
MOTION SETUP
PANTILT SERUP
SCHEDULE SETUP
CONFIGURATION

RUN

SELECT MENU : ▲ ▼, & [ENTER]

OFF
OFF
OFF
OFF
OFF
OFF
OFF

CONFIGURATION

RECORD SETUP

EXTERNAL DEVICE

FACTORY DEFAULT

LANGUAGE ENGLISH

SELECT MENU : ▲▼, & [ENTER]

34

CHAP. 6 Network Setup

CHAP. 6 Network Setup

6-1. DVR Network Configuration

Please call your provider to identify what type of service they are providing you.
You will need to know following ;

Upload speed – For your own knowledge for expected frame rates
Download speed – For your own knowledge for expected frame rates
Addressing – For determining what scenario you should follow
Router On Site or Just a Modem – For determining what scenario you should follow

※NOTE : If your provider is using PPPOE (usually DSL providers), you MUST have a IP Share

installed on site and follow 3) Dynamic IP of PPPOE (DSL) for DVR setup and access.

※PLEASE verify Internet access after installing any new equipment (routers, switches, modems, etc.).

PC’s TCP/IP Setting

Before configuring the DVR, please fill out the information below if applicable ;

Choose any PC on your network and determine its TCP/IP settings;

IP Address :

Subnet Mask :

Default Gateway :

Next pages are several network scenarios. Please identify which scenario your current network
falls within and follow the instructions for configuring and accessing your DVR via TCP/IP.

(ex.192.168.1.5)

(ex. 255.255.255.0)

(ex.192.168.1.1)

35

CHAP. 6 Network Setup

1) Static IP

User input IP address in IP CONFIG SETUP which is assigned from ISP company.

1. Verify if IP address is OK or not with PC before connecting DVR.

2. Connect LAN cable to DVR after confirmation.

3. DVR : MENU  EXTERNAL DEVICE  TCP/IP

4. Set DHCP to MANUAL and go into TCP/IP SETUP.

5. Verify if MAC ADDRESS starts from 00-0A-A2….

6. Input IP address which is assigned from ISP company.

7. Set IP PORT. (50000 recommended)

8. Input GATEWAY which is assigned from ISP company.

9. Input SUBNET MASK which is assigned from ISP company.

10. Go out of MENU SETUP.

11. Turn off and on Modem (Router) which is provided by ISP company.
 This is to reset client of MAC from ISP company.

User have to wait for 30 seconds after turning on.

12. Access DVR with Remote Viewer software.

Internet

Internet (Static IP)

Remote Viewer

InternetInternet

(Client)

DVMR

(Server)

* If user fail to access, please verify 1, 6, 7, 8, 9, 11 again.

* When speed is too slow and connection fails after access : MENU  EXTERNAL

DEVICE  TCP/IP SETUP  CONNECTION SETUP

Increase value of Timeout to find the most suitable speed.

36

2) Dynamic IP

1. Verify if IP address is OK or not with PC before connecting DVR.

2. Connect LAN cable to DVR after confirmation.

3. Turn off and on Modem (Router) which is provided by ISP company.
 This is to reset client of MAC from ISP company.

User have to wait for 30 seconds after turning on.

4. Turn off and on DVR.

5. DVR : MENU  EXTERNAL DEVICE  TCP/IP

6. Verify if MAC ADDRESS starts from 00-0A-A2….

7. Set DHCP to AUTOMATIC and detect IP to get Dynamic IP.

8. Go out of MENU SETUP after getting IP successfully.

9. Access DVR with Remote Viewer software.

CHAP. 6 Network Setup

Remote Viewer

(Client)

Internet

InternetInternet

Cable Modem

(Dynamic IP)

LAN

LAN

LANLAN

Internet

* If user fail to access, please verify 1, 3, 4 again.

* When speed is too slow and connection fails after access : MENU  EXTERNAL

DEVICE  TCP/IP SETUP  CONNECTION SETUP

Increase value of Timeout to find the most suitable speed.

DVMR

(Server)

37

CHAP. 6 Network Setup

3) Dynamic IP of PPPoE (DSL)

DVR doesn’t support DSL (PPPoE), user have to set NETWORK with IP SHARE if
user need to access DVR remotely. At this time, User have to port forward on DVR.
Please contact IP SHARE Manufacturer if you need to know how to forward port.

Even though user have Static/Dynamic IP, if user want to use another device
(PC) through IP SHARE, user can set NETWORK as follows,

1. Verify if IP address is OK or not with PC before connecting DVR.

2. Connect Router (IP SHARE) to DSL modem as shown the following picture.

3. Set the internet connection on Router (IP SHARE). (Refer to the Router Manual.)

4. Verify if sub-group of network in Router is OK or not.

5. Connect DVR to Router.

6. DVR : MENU  EXTERNAL DEVICE  TCP/IP

7. Set DHCP to MANUAL and go into TCP/IP SETUP.

8. Verify if MAC ADDRESS starts from 00-0A-A2….

9. Input internal IP address which user assigned from Router.

10. Set IP PORT. (50000 recommended)

11. Input GATEWAY of Router.

12. Input SUBNET MASK of Router.

13. Go out of MENU SETUP.

14. Forward port from Router. (Refer to the Router Manual.)

15. Access DVR with external IP and Port (Port forwarded).

* If Router support DDNS, user can access Remote Viewer using Domain Information.

Remote Viewer

(Client)

* If user fail to access, please verify 1, 4, 15 again.

* When speed is too slow and connection fails after access : MENU  EXTERNAL

DEVICE  TCP/IP SETUP  CONNECTION SETUP

Increase value of Timeout to find the most suitable speed.

Internet

Internet

InternetInternet

DSL Modem

(Dynamic IP)

LAN

LAN LAN

LANLAN

Router

LAN

LANLAN

or Gateway

(IP Share)

DVMR

(Server)

38

6-2. Remote Viewer program

MAIN INTERFACE

3

2

CHAP. 6 Network Setup

1

6

7

8

5

4

①

- Power button : Press the Power switch to exit the program. Please disconnect the live feed before
powering off the software

②

- Connect button : Press the Connect button to view the live images from the DVR. These are the same
images being displayed on the monitor of the DVR, with a delay depending on your
internet connection at both the DVR location and from where you’re currently accessing.

③

- Disconnect button : Press this button to disconnect from the DVR unit. Then you may power off the

software.

④

- Screen Division button : Select how many channels to view simultaneously(single,4-split,9-split,

or 16-split). When you select a view you will see the Channel Numbers highlighted
which determine what channels are currently being viewed.

⑤

- Channel number button : Select the channel that you want to view based on what Screen Division

view is enabled.

⑥

- Status window : Display’s the current time and date based. The date is in the format : Year/Month/Day.

You will also see the status of your connection.

⑦

- Setting, Playback, and Sequence buttons ; a. Setting : Enables the software configuration screen.

b. Playback : Enables the remote playback screen.
c. Sequence : When in single channel view, hitting the sequence button will sequence

through all active channels at a speed specified in the settings menu.

⑧

- PTZ control : You can control a PTZ camera via the software with these controls.

a. First, you must input or configure the specific PTZ protocol into the software in

order to communicate with the PTZ device.

b. When you press any of the controls for the PTZ, please press and hold the button

for 1-2 seconds per instance to compensate for the data transmission rate. If you
do not and instead simply click the PTZ buttons, you may get undesired results

(having the requested operation transmitted repeatedly, regardless of your intention).

c. The plus and minus buttons send the PTZ commands to the corresponding PTZ

camera ID.

39

IP/PORT Setting Screen

CHAP. 6 Network Setup

IP List

MANUAL Input IP address and PORT manually
DDNS Receive IP address and PORT from DDNS Server.

For further information of DDNS, please contact your vendor.

Name Name of IP address on the list.
Address Input IP address which is set on DVR
PORT Input PORT which is set on DVR
ID Input ID which is set on DVR. (Please input ‘admin’.)
Password Input password which is set on DVR

IP List It shows IP list which user input manually.

Select Button Select IP and PORT on the list.
Save Button Save IP and PORT on the list.
Delete Button Delete IP and PORT on the list.

40

PTZ/SAVE Setting Screen

CHAP. 6 Network Setup

Circular Monitoring Interval : This indicates the speed of the channels sequence when the

SEQUENCE button is used from the main interface.

Scan Rate : Set speed of playback.

PTZ TYPE : Select PTZ camera which is connected to DVR.

PTZ Baud Rate : Enter the Baud Rate of your PTZ camera.

Set Path to Save Downloaded image : Determines the location and folder on your PC where the

downloaded video clips are stored.

Run in full screen mode : When checked, this will enable the program to re-adjust the interface to

completely fill your computer screen.

41

PLAYBACK INTERFACE through Remote Viewer

CHAP. 6 Network Setup

2

3

4

5

6

1

7

8

9

10

Function of each button in Search window.

①

Exit : Exit to live window.

②

Full screen : Select a certain camera to view in full screen.

③

Quad : To view quad mode (4 channels at the same time)

④

Time : The recording time & date information of the pictures which is being played.

⑤

Channel selection : Select each camera.

⑥

Time selection : Select a time from which user want to see. The playback will be started from this

point.(drag the point using mouse)

⑦

Start and end time : Indicate record starting time and end time of images on HDD

⑧

Other operating button : Refer to the next page description.

42

CHAP. 6 Network Setup

: Play fast backward

: Play backward(1X)

: Play forward(1X)

: Play fast forward

: Stop playback

⑨

Command button.

a) SAVE : After pressing the Stop button, click SAVE button to save the currently viewed image in jpg

format.

b) PRINT : After pressing the Stop button, click PRINT button to print the currently viewed image.
c) RECORD : Press this button to download playback images transmitted from DVR unit into your

PC. User can see saved images using Windows Media Player.

: Move to the start of recording

: Move to the previous hour

: Move to the afterward hour

: Move to the end of recording

⑩

Calendar

Use this to select the date you wish to search. The filled in square outlines the date that is at the
beginning of the hard drives. The outlined square indicates the data at the end of the hard drives.
Select the date you wish to view. Verify a filled in square for that particular date. If an invalid date is
selected it will default to the beginning of the hard drive(s).

43

9

Back-up CD Player

6-3.

CHAP. 6 Back-up CD Player

1

2

10

8

67

DVR units are with a built-in CD-RW, and user can copy images to CD.
Using back-up CD player, user can see images on back-up CD, and function of each button in
Back-up CD player is as below.

①

Time : Current time.

②

Status Window : Start & End of time & date, Status of operating button.

When user play forward/backward, recorded time will appear.

③

Play Speed button : User can adjust play speed by pressing up/down button.

Speed (1/4X, 1/2X, 1X, 2X, 4X, 8X, 16X) Delay : (1, 2, 4, 8, 16, 32)

④

Operation button : User can search recorded data using these buttons.
a) Move the slide bar to start position
b) Play fast backward in preset speed
c) Play backward at 1x speed
d) Pause
e) Play forward at 1x speed
f ) Play fast forward in preset speed
g) Move the slide bar to end position

⑤

Function button

a) OPEN : Open the Back-up CD Player.
b) EDIT : User can edit, save and print recorded image on Edit mode. This edit button will work

when you selected one of 16 cameras.

c) EXIT : Exit from Back-up CD Player.

⑥

Channel button : Select channel to see pictures in full screen.

⑦

Slide Bar : Move to a point from which user want to see.

⑧

Page button : This button is just working when screen-division is 4-split in 8 ch DVR, or 4-split or

8-split in 16 ch DVR. Moves to next page.

⑨

Screen division : 1/4/9/16

3

b

c

a

e

4

d

g

f

5

44

CHAP. 6 Back-up CD Player

⑩ When you open the file, audio menu OSD will come up automatically.

- on : check to output recorded sound, then choose the audio channel 1,2,3 or 4

- skip : skip images forward.
* During playback, you can control only.

* During playback, only one channel is displayed and can not be changed to multi or full screen.

Image EDIT

Contrast

a

a

1

Sharpness

①

Image Edit Status Window : Shows record time & date, Image size, Command status.

②

Edit Button : User can adjust color tone of copied images using this button.

- Contrast :
a) make bright part of image brighter and dark part of image darker
b) To reduce light and shade, lower contrast a little

- Brightness
a) make an image brighter
b) make an image darker

- Sharpness : give sharp-edge effect

- Blur : make an image soft

b

b

Brightness

Save Print Exit

a b c

Blur

2

3

③

Function button

a) Save : User can save an image in JPEG format. It is saved in the folder where you installed

back-up CD player.
b) Print : User can print current image user selected
c) EXIT : Return to Back-up CD Player mode.

45

CHAP. 7 DDNS Web Server

CHAP. 7 DDNS Web Server

CHAP. 7 DDNS Web ServerCHAP. 7 DDNS Web Server

* Register DVR for DDNS Web-server and set DVR as shown below,

7777----1. Registering DVR for DDNS (DDNS Web

1. Registering DVR for DDNS (DDNS Web----server)

1. Registering DVR for DDNS (DDNS Web1. Registering DVR for DDNS (DDNS Web

server)

server)server)

CHAP 7. DDNS Web Server

1) Please access

2) Please click DVR Add to register DVR.

www.j2kip.com and Register Member ID.

46

3) Please click confirm after inputting DVR Name & Mac Address.

CHAP 7. DDNS Web Server

4) Now, DVR is listed on DDNS Web Server without IP and Port number.

47

CHAP 7. DDNS Web Server

7777----2.

2. DDDDDNS Set Up in DVR

DNS Set Up in DVR

2. 2.

DNS Set Up in DVRDNS Set Up in DVR

* The following setting is a sample for a cable modem connected to DVR directly.

1) Click Menu and Enter into ‘LOGIN -> EXTERNAL DEVICE -> TCP/IP SETUP’

2) Go to IP Config Setup, if user set DHCP ‘Automatic’, it detects IP address automatically.

IP CONFIG SETUP

MAC ADDRESS

_ _ _ _ _ _ _ _ _ _ _

00-0A-A2-00-00-00

IP ADDRESS

IP PORT

GATEWAY

SUBNET MASK

_ _ _ _ _ _ _ _ _ _ _

_ _ _ _ _ _ _ _ _ _ _

_ _ _ _ _ _ _ _ _ _ _

_ _ _ _ _ _ _ _ _ _ _

DHCP SETUP

SELECT MENU : ▲▼, & [ENTER]

3) Go to the previous menu and enter into DDNS Setup.

192.168.001.160

50000

192.168.001.001

255.255.255.000

AUTOMATIC

TCP/IP SETUP

IP CONFIG SETUP
DDNS SETUP
CONNECTION SETUP
DHCP SETUP
EVENT SERVER SETUP

48

CHAP 7. DDNS Web Server

4) Set DDNS ON/OFF “ON”.
IP address which is assigned from DHCP Server is automatically input on DNS Server.

DDNS SETUP

DDNS ON/OFF OFF
DDNS SERVER 211.062.253.087
INTERVAL D-00 H-00 M-20
REGISTER

-------------------------------------------------------------------------­DDNS STATUS
IP ADDRESS

---.---.---.---

IP PORT ----­REMAIN TIME D-00 H-00 M-00
LAST REGISTERATION DATE

>

SELECT : ▲▼, CHANGE VALUE : + -

5) Go down to REGISTER and push ENTER button to renew IP and Port resistered on DDNS

Sever(www.j2kip.com)

( Interval : connection interval time between DVR and DDNS Server)
D = Day, H = Hour, M = Minute

DDNS SETUP

DDNS ON/OFF ON
DDNS SERVER 211.062.253.087
INTERVAL D-00 H-00 M-20
REGISTER

-------------------------------------------------------------------------­DDNS STATUS REGISTER OK
IP ADDRESS

192.168.001.160

IP PORT 5000
REMAIN TIME D-00 H-00 M-20
LAST REGISTERATION DATE
> WED. 12 JUL 2006 09 : 21 : 36 GMT

SUCCESS TO REGISTER DVR INFO

SELECT : ▲▼, CHANGE VALUE : + -

49

CHAP 7. DDNS Web Server

6) Go to your PC again after you see “SUCCESS TO REGISTER DVR INFO.” and then Click ‘refresh’
button. Then, DDNS Server automatically catches your DVR’s IP address and Port number.

Note.

Note.

Note.Note.

Before using Web-Viewer, please add www.j2kip.com on Trusted Sites at first installation as
follows.
(Tools -> Internet Options -> Security -> Trusted Sites)

①①①①

②②②②

50

③③③③

CHAP 7. DDNS Web Server

④④④④

⑤⑤⑤⑤

⑥⑥⑥⑥

⑦⑦⑦⑦

Click

Click

ClickClick

Leave this check box empty

51

CHAP 7. DDNS Web Server

7777----3. Web Program

3. Web Program

3. Web Program3. Web Program

*If ActiveX control installation is required for the first time access,please click ‘Yes’.

Click these icons, then it connects to DVR
Input information needed for network
connection to DVR manually.

automatically via DDNS Server.

VIEWER Enables to show live image display.
BACKUP Enables to back up recorded images in DVR to your PC.
PLAYER Enables to back up recorded images on your PC.

52

CHAP. 8 Specifications

• The best picture quality in Playback(JPEG-2000)

• Real time live display in all channels

• 16 channel video 480(400)ips recording capability

• Triplex (Playback/Recording/Ethernet)

• Multi-language menu

• Remote monitoring and download through network

• Convenient search function with Jog/shuttle

• VGA option available (Supporting TFT LCD Monitor)

• USB (Device) port for firmware upgrade

• Easy PTZ camera control by pre-assigned buttons

• Password Protection

• Remote Controller

CHAP. 8 Specifications

Multiplex function

Storage Internal HDD Up to 2 HDDs with no limitation in capacity (SATA HDD support)

Capacity CD-RW For Backup

Video Inputs Composite 16Ch

Outputs Composite 2Ch (Monitor / SPOT)

VGA 1Ch (Supporting TFT LCD Monitor/Option)

Loop out 16Ch

Compression JPEG-2000

Compression Rate Basic

(Image size fixed) Normal

Display Speed Real Time display

Recording Recording Mode Schedule (Time, Motion, Alarm), Emergency

/Search Search Event Search, Date/Time Search, Search Bar (Jog/Shuttle)

Recording Speed (NTSC/PAL) Full (120/100), Dual (240/200)

Recording Resolution (NTSC/PAL) Full (720x240/720x288), Dual (360x240/360x288)

Multi-language English, Spanish, German, Italy, France, to be added more

Switching Interval 1~99 sec selectable

Live Division Screen 1 / 4/ 6/ 8/ 9/ 13/ 16 Split

Alarm Inputs 16 Alarms (NO/NC selectable in SETUP menu)

Outputs 1 (NO/NC)

Post Alarm Duration of alarm output : 1 sec ~ 300 sec selectable

Motion Detection Area division : 16 x12 / Detection Division : 32 x 24

Network Ethernet (TCP/IP), Remote viewer program included

Backup

PTZ Control RS-485, Key Control( Key assigned for each PTZ command)

Firmware upgrade USB port for firmware upgrade, CD-R

Serial I/F RS-485 For PTZ camera control

RS-232C For operation using keyboard of PC

AUDIO

Power Requirements DC 12V 6.67A Adaptor

Weight 8.5kg

Dimensions (WXHXD) mm 436 X 396 X 88

Packing 600 X 520 X 180

Design and specifications are subjected to changes without notice

Input

Output

Triplex (Playback/Recording/Ethernet)

Enhanced

Fine

Super Fine

Digital Zoom, Freeze function available in Live mode, PIP, SEQ

VCR, CD-RW back-up, USB backup, Download via IP Network

4CH Microphone Input

1CH Speaker Output

53

CHAP. 9 Remocon Key Definition

CHAP. 9 Remocon Key Definition

MODE

▲◀▶▼

▲◀▶▼

▲◀▶▼▲◀▶▼

OK

CH + / -

+ / -

AUDIO

PTZ

SEARCH

MENU

F1

F2

F3

F4

Screen Division / Change Mode

Move menu items & Change Value

Enter Menu & Select

Change Channel

Change Value

Change Audio Ch

OSD DISPLAY On/Off

4-SPLIT

9-SPLIT

16-SPLIT

PTZ On/Off

Search Menu

Menu

PTZ CONTOL

SET

CLEAR

GOTO

AUTO

1~9

0

ESC

FUNC

I◀◀◀◀

◀◀◀◀

▶▶▶▶

▶▶▶▶I

◀◀

◀◀

◀◀◀◀

II

■■■■

▶▶

▶▶

▶▶▶▶

SEQ

FRZ

PIP

ZOOM

SET PRESET

CLEAR PRESET

GOTO PRESET

AUTO PAN

Select Ch / Input Number

Indicates 2 digits

‘0’ + ‘0’ = ’10’

‘0’ + ‘0’ = ’11’

Emergency Recording

<No functions>

Playback location

Backward Playback

Start Playback / Fast Forward

Go back to the end

Decrease Playback Speed

Pause

Stop

Increase Playback Speed

SEQUENCE

FREEZE

Picture In Picture

ZOOM

54

MEMO :

55

MEMO :

56

MEMO :

57

16Channel Stand Alone DVR

Audio, USB Backup available

Best Picture Quality - JPEG2000

58