Maxon Electronics Australia MM-5100P Users Manual

FCC Documentation

User Manual

CM-5100P CDMA 1X Network card

Incorporating extracts of MM-5100P User Manual

Version : 0.1
Date : JUL. 25, 2003

1/25

Maxon Proprietary : Restricted Distribution. This document is the sole and exclusive property of Maxon

Australia. Not to be distributed or divulged without prior written agreement.

Maxon Electronics Australia Pty. Ltd. 36A Gibson Avenue, Padstow, N.S.W. Australia
Tel : [phone] Facsimile : [phone] URL : http//www.maxon.com.au

FCC Documentation- CM-5100P CDMA 1X Network card

FCC RF EXPOSURE COMPLIANCE

In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report

and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF)

electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the

safety standard previously set by both U.S. and international standards bodies. The design of this phone

complies with the FCC guidelines and these international standards.

Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could

impair call quality, damage the phone, or result in violation of FCC regulations.

This CDMA PCMCIA Card has been tested for FCC RF exposure hand and body SAR compliance with

the MM-5100P PCMCIA Card form factor. In order to comply with FCC RF exposure requirements, the

CDMA PCMCIA Card module must be operated with the MM-5100P PCMCIA Card form factor. The use

of this device in any other type of host configuration may not comply with FCC RF exposure

requirements and should be avoided. During operation, a 1.5cm separation distance should be

maintained between the antenna, whether extended or retracted, and the user’s/bystander’s body

(excluding hands, wrists, feet, and ankles) to ensure FCC RF exposure compliance.

CAUTION

Change or modification without the express consent of Maxon Electronics Australia Pty. Ltd. voids the user’s

authority to use the equipment. This equipment has been tested and found to comply with the limits pursuant

to Part 15.105 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference in an appropriate installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not used in accordance with instructions, can cause harmful radiation to radio communication.

However, there is no guarantee that interference will not occur in a particular installation. If the equipment

does cause harmful interference in radio and television reception, which can be determined by turning the

equipment on and off, the user is encouraged to try to correct the interference by one or more of the following

measures:

z Reorient or relocate the receiving antenna

z Increase the separation distance between the equipment and the receiver

z Contact Maxon Electronics Australia Pty. Ltd. Technical Support for assistance.

2/25

Maxon Proprietary : Restricted Distribution. This document is the sole and exclusive property of Maxon

Australia. Not to be distributed or divulged without prior written agreement.

Maxon Electronics Australia Pty. Ltd. 36A Gibson Avenue, Padstow, N.S.W. Australia
Tel : [phone] Facsimile : [phone] URL : http//www.maxon.com.au

FCC Documentation- CM-5100P CDMA 1X Network card

Table of contents

1. Contact Information······························································································· 4

2. Product Overview ·································································································· 5

2.1 Overview........................................................................................................ 5

2.2 What is the CM-5100P CDMA network card ............................................... 5

2.3 Supplied accessories................................................................................... 5

3. Specifications ········································································································ 6

3.1 Mechanical Specifications........................................................................... 6

3.2 Environment Specifications ........................................................................ 6

3.3 Electrical Specifications .............................................................................. 6

3.4 CDMA RF Specifications.............................................................................. 7

4. Instruction ·············································································································· 9

4.1 Supplied accessories................................................................................... 9

4.2 Getting started .............................................................................................. 9

5. Circuit description ······························································································· 14

5.1 CM-5100P CDMA 1X Network card circuit description ...........................14

5.2 Power interface part ................................................................................... 15

5.3 Digital part...................................................................................................15

5.4 RF part ......................................................................................................... 16

6. Range of operating power levels and description of means for variation of

operating power··································································································· 20

7. Description of frequency determining and stabilizing circuitry······················21

8. Description of circuit employed for suppression of spurious radiation ········ 23

9. Description of modulation system used ··························································· 24

3/25

Maxon Proprietary : Restricted Distribution. This document is the sole and exclusive property of Maxon

Australia. Not to be distributed or divulged without prior written agreement.

Maxon Electronics Australia Pty. Ltd. 36A Gibson Avenue, Padstow, N.S.W. Australia
Tel : [phone] Facsimile : [phone] URL : http//www.maxon.com.au

FCC Documentation- CM-5100P CDMA 1X Network card

1. Contact Information

If you have any technical queries about this manual, please contact:

Maxon Electronics Australia Pty. Ltd.

36a Gibson Avenue

Padstow, New South Wales 2211

Australia

Phone: [phone]

Fax: [phone]

Mr. Ray Sanders-Managing Director

Mr. Ashween Prasad- Technical Manager

Email: [e-mail]

4/25

Maxon Proprietary : Restricted Distribution. This document is the sole and exclusive property of Maxon

Australia. Not to be distributed or divulged without prior written agreement.

Maxon Electronics Australia Pty. Ltd. 36A Gibson Avenue, Padstow, N.S.W. Australia
Tel : [phone] Facsimile : [phone] URL : http//www.maxon.com.au

FCC Documentation- CM-5100P CDMA 1X Network card

2. Product Overview

2.1 Overview

The CM-5100P wireless network card fits into a standard type 2 PC card slot (available on most

notebook PCs). This card functions as a wireless network card, a modem, a mobile phone and

allows you to connect to the Internet, send and receive e-mail, connect to a corporate network, and

make phone calls, without the need of a network cable or phone line.

The CM-5100P card performs data communication functions between Host and IS-95 CDMA Cellular

station.

2.2 What is the CM-5100P CDMA network card

- IS-95A, B, and cdma2000-1X CDMA Protocol Support

- Standard Type 2 PC card slot

- Remote controlled by AT commands

- DATA transmission up to 153Kbps [network limited]

- LED indicating of the modem status

2.3 Supplied accessories

- CM-5100P CDMA 1X network card (1)

- Ear-piece assembly (1)

- Driver CD (1)

5/25

Maxon Proprietary : Restricted Distribution. This document is the sole and exclusive property of Maxon

Australia. Not to be distributed or divulged without prior written agreement.

Maxon Electronics Australia Pty. Ltd. 36A Gibson Avenue, Padstow, N.S.W. Australia
Tel : [phone] Facsimile : [phone] URL : http//www.maxon.com.au

FCC Documentation- CM-5100P CDMA 1X Network card

3. Specifications

3.1 Mechanical Specifications

Table 3.1 mechanical specifications

Dimensions 95mm x 54mm x 5mm, except antenna parts

Weight Approx. 45g , except ear-piecd assemblies

Housing Material CASE – STAINLESS STEEL

3.2 Environment Specifications

Table 3.2 environment specifications

Operating conditions 0°C ~ +60°C , 85%(at 50(C), relative humidity (non-condensing)

Storage Temperature -40°C ~ +70°C

Humidity 95%, non-condensing

3.3 Electrical Specifications

Table 3.3 Current Consumption

- DC input voltage +5VDC from PCMCIA Slot

- Maximum current Under 1.0A

- Typical current Under 200mA

- Digital block operating voltage +3.0V (typical)

On communication @ Maximum TX Power (24+/- 0.3dBm) Under 700mA

(Note) The current consumption might vary of 5% over the whole operating temperature range.

6/25

Maxon Proprietary : Restricted Distribution. This document is the sole and exclusive property of Maxon

Australia. Not to be distributed or divulged without prior written agreement.

Maxon Electronics Australia Pty. Ltd. 36A Gibson Avenue, Padstow, N.S.W. Australia
Tel : [phone] Facsimile : [phone] URL : http//www.maxon.com.au

FCC Documentation- CM-5100P CDMA 1X Network card

3.4 CDMA RF Specifications

RF performances are compliant with IS-95A/B, cdma2000-1X RTT CDMA Protocol.

3.4.1 Transmitter specifications

Table 2.4 Transmitter performance

Type of Multiplexing Frequency-Division Duplex

Frequency Range 824.64MHz ~ 848.37MHz

Channel Number 20CH

Bandwidth 1.23MHz

Occupied Bandwidth Under 1.32MHz

Type of Oscillation PLL Synthesizer & VCTCXO(19.2MHz)

VCO Output Frequency Range

( divide-by-2 frequency range)

Intermediate Center Frequency 138.6MHz

Modulation Method OQPSK

RF Maximum Output Power 0.28W (24.5dBm/1.23MHz)

Frequency Stability(Accuracy) Under defined freq. +/- 300Hz

Waveform Quality Over 0.944

Conducted Spurious Emission Over carrier +/-900KHz, -42dBc/30KHz

Common RF Impedance 50ohm

Supplied voltage +3.8V DC @ Power Amp.

1372.08MHz ~ 1421.54MHz

(686.04MHz ~ 710.77MHz)

Over carrier +/-1980KHz, -54dBc/30KHz

+2.85V DC @ TX block

7/25

Maxon Proprietary : Restricted Distribution. This document is the sole and exclusive property of Maxon

Australia. Not to be distributed or divulged without prior written agreement.

Maxon Electronics Australia Pty. Ltd. 36A Gibson Avenue, Padstow, N.S.W. Australia
Tel : [phone] Facsimile : [phone] URL : http//www.maxon.com.au

FCC Documentation- CM-5100P CDMA 1X Network card

3.4.2 Receiver specifications

Table 2.5 Receiver performance

Type of Receiving Super Heterodyne Method

Frequency Range 869.94MHz ~ 893.37MHz

Channel Number 20CH

Band width 1.23MHz

Type of Oscillation PLL Synthesizer & VCTCXO(19.2MHz)

VCO Output Frequency Range

( divide-by-2 frequency range)

1372.08MHz ~ 1419.54MHz

(686.04MHz ~ 709.77MHz)

Intermediate Center Frequency 183.6MHz

Modulation Method QPSK

Receiver Sensitivity Under -104dBm @FER=0.5%

Single Tone Desensitization

(-30dBm @F

+/-900KHz)

C

Inter-modulation

(Fc +/-900KHz&1.7MHz)

-43dBm Under -101dBm @FER=1%

-32dBm Under -90dBm @FER=1%

Under -101dBm @FER=1%

-21dBm Under -79dBm @FER=1%

Common RF Impedance 50ohm

Supplied voltage +3.0V DC

8/25

Maxon Proprietary : Restricted Distribution. This document is the sole and exclusive property of Maxon

Australia. Not to be distributed or divulged without prior written agreement.

Maxon Electronics Australia Pty. Ltd. 36A Gibson Avenue, Padstow, N.S.W. Australia
Tel : [phone] Facsimile : [phone] URL : http//www.maxon.com.au